Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cation-disordered Li-Excess cathodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

15 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Fluorination effect for stabilizing cationic and anionic redox activities in cation-disordered cathode materials

We see that cation-disordered Li-excess cathodes with oxygen redox reactions are promising candidates for high-energy-density Li ion batteries. Nevertheless, the oxygen redox process that is required for the high capacity often comes with the oxygen loss, which leads to severe capacity degradation and voltage decay. In this work, we have successfully synthesized a series of Li-excess cation-disordered cathodes (Li 1.2 Mn 0.4+x Ti 0.4-x O 2-x Fx) (0 ≤ x ≤ 0.2) with different fluorine (F) contents. The electrochemical performance results show that the Li 1.2 Mn 0.55 Ti 0.25 O 1.85 F 0.15 (LMTOF0.15) exhibits the highest reversible capacity (275 mAh g -1 , under 30 mA g -1 ), cyclability, and voltage retentions. The mapping of resonant inelastic X-ray scattering (mRIXS) and differential electrochemical mass spectroscopy (DEMS) results reveal that the fluorination enhances the reversible lattice oxygen redox reaction while suppressing irreversible gas release and surface reactions. The X-ray Absorption Spectroscopy (XAS) during the initial two cycles shows that F-substitution alleviates the reduction of the Mn valence state during the whole (dis)charge processes in the bulk and at the surface of the material, results in higher average discharge voltage. In addition, the introduction of F improves the structural stability and suppresses local lattice distortion of the material. Therefore, LMTOF 0.15 is able to cycle with smaller polarization, less interfacial side reaction and Mn dissolution, and therefore results in enhanced cyclability. This work provides a comprehensive understanding of the fluorination effect on the cationic and anionic redox activities in cation-disordered Li-excess cathodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Increasing Capacity in Disordered Rocksalt Cathodes by Mg Doping

Using both computations and experiments, we demonstrate that the performance of Li-excess cation-disordered rocksalt cathodes can be improved by Mg substitution. Furthermore we find that Mg reduces the amount of Li in the compound that is strongly bound to F and thereby increases the capacity. This enables the use of fluorination as a tool to improve stability of the compounds without significant loss of capacity. Mg emerged as the most optimal substitution element from a systematic computational study aimed at identifying inactive doping elements with a strong enough bonding strength to fluorine to displace Li from the F environments. Our results also show that capacity can be traded for cycle life depending on whether Mg is substituted for Li or for the redox metal. This design strategy should be considered in fluorinated cathodes, which will facilitate the design of optimized disordered rocksalt oxyfluoride cathodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Redox Behaviors in Li-Excess Cation-Disordered Mn-Nb-O-F Rocksalt Cathode

Lithium-excess cation-disordered rocksalt oxide (DRX) is a new choice of high energy Li-ion cathode materials. DRX cathode can deliver an exceptionally high capacity of >250 mAh/g, implying the participation of cationic transition metal and anionic oxygen redox in the electrochemistry. Understanding the explicit roles of both redox reactions in the newly developed cathode is of critical importance to further development of these materials. Herein, we synthesize a representative Mn-redox-based fluorinated DRX material, Li1.2Mn0.625Nb0.175O1.95F0.05 (LMNOF). Using a comprehensive suite of electroanalytical methods, we probe the cationic and anionic redox processes and their evolution upon cycling exclusively from the electrochemical point of view. This work sheds light on understanding of cationic and anionic redox and their roles in the capacity loss for high-capacity fluorinated DRX cathode, meanwhile, showcases an explicit approach to study the electrochemistry of novel electrode materials using such non-disruptive electroanalytical methods.

Li-ion battery, high-capacity cathode, Li-excess m↗
DOE OSTI2023

Toward Stable Cycling of a Cost-Effective Cation-Disordered Rocksalt Cathode via Fluorination

The recently developed Li-excess cation-disordered rock salts (DRXs) exhibit an excellent chemical diversity for the development of alternative Co/Ni-free high-energy cathodes. Herein, the synthesis of a highly fluorinated DRX cathode, Li 1.2 Mn 0.6 Ti 0.2 O 1.8 F 0.2 , based on cost-effective and earth-abundant transition metals, via a solid-state reaction, is reported. The fluorinated DRX cathode using ammonium fluoride precursor exhibits more uniform particle size and delivers a specific discharge capacity of 233 mAh g -1 and specific energy of 754 Wh kg -1 , with 206 mAh g -1 retained after 200 cycles. Further, the combined synchrotron X-ray absorption spectroscopy and resonant inelastic X-ray scattering spectroscopy analysis reveals that the remarkable cycling performance is attributed to the high fluorination and thus enhanced Mn content, enabling the utilization of more Mn redox than the oxide analog. This study demonstrates a great promise to develop next-generation cost-effective DRX cathodes with enhanced capacity retention for high-energy Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Phase Transformation Enables Stable Cycling and Fast Charging of Cation-Disordered Rocksalt Cathodes

Developing high-capacity, long-life cathodes is critical to overcome the energy limitations of current Li-ion batteries. In this work, we report a Li-excess cation-disordered rocksalt (DRX) cathode, Li 1.167 Mn0.7Ti 0.133 O 1.8 F 0.2 (M 0.7 F 0.2 ), which demonstrates excellent electrochemical performance. This cathode delivers a capacity approaching 250 mAh g –1 and maintains 200 mAh g –1 over 200 cycles with an average discharge voltage of 3.1 V at 2 V cutoff. The formation of a spinel-like phase during cycling enables fast charging, achieving over 240 mAh g –1 at 2C for 100 cycles. Combined X-ray absorption spectroscopy and transmission electron microscopy reveal reversible electrochemical redox processes and stable Mn local structures during 2 V discharge. These results highlight the potential of DRX cathodes for next-generation Li-ion batteries and provide insights into strategies to overcome kinetic limitations and optimize the cathode-electrolyte interface.

25 ENERGY STORAGE↗
DOE OSTI2023

Atomic-scale probing of short-range order and its impact on electrochemical properties in cation-disordered oxide cathodes

Abstract Chemical short-range-order has been widely noticed to dictate the electrochemical properties of Li-excess cation-disordered rocksalt oxides, a class of cathode based on earth abundant elements for next-generation high-energy-density batteries. Existence of short-range-order is normally evidenced by a diffused intensity pattern in reciprocal space, however, derivation of local atomic arrangements of short-range-order in real space is hardly possible. Here, by a combination of aberration-corrected scanning transmission electron microscopy, electron diffraction, and cluster-expansion Monte Carlo simulations, we reveal the short-range-order is a convolution of three basic types: tetrahedron, octahedron, and cube. We discover that short-range-order directly correlates with Li percolation channels, which correspondingly affects Li transport behavior. We further demonstrate that short-range-order can be effectively manipulated by anion doping or post-synthesis thermal treatment, creating new avenues for tailoring the electrochemical properties. Our results provide fundamental insights for decoding the complex relationship between local chemical ordering and properties of crystalline compounds.

25 ENERGY STORAGE↗
DOE OSTI2021

Understanding cation-disordered rocksalt oxyfluoride cathodes

Partial fluorine (F) substitution into the oxygen (O) sublattice has been shown to improve cycling stability of cation-disordered Li-excess rocksalt oxide (DRX) cathodes. Detailed understanding on failure mechanisms and key optimization knowledge of fluorinated-DRX (F-DRX), however, are lacking. In the present study, we incorporate different amounts of F into a baseline DRX system, Li 1.2 Ti 0.4 Mn 0.4 O 2 (LTMO3.0, 3.0 denotes nominal Li/Mn ratio), and synthesize two oxyfluoride compounds, Li-rich Li 1.3 Ti 0.3 Mn 0.4 O 1.7 F 0.3 (LTMOF3.25) and Mn-rich Li 1.2 Ti 0.2 Mn 0.6 O 1.8 F 0.2 (LTMOF2.0) with an increased and reduced Li/Mn ratio of 3.25 and 2.0, respectively. Through careful monitoring of chemical and structural evolution, we show that cycling-induced changes are manifested not only by Mn reduction and degradation of its local coordination environment, but also by F enrichment and formation of LiF-type of domains on the surface. A “concerted-densification” based failure mechanism, involving atomic-level changes in both transition-metal cationic sublattice and oxygen/fluorine anionic sublattice, is proposed for the degradation in F-DRX cathode materials. The study reveals that increasing F content accompanied by reduced Li/Mn ratio mitigates the degradation process, offering key design strategies in achieving balanced cathode capacity and stability.

25 ENERGY STORAGE↗
DOE OSTI2023

Quantitative Decoupling of Oxygen-Redox and Manganese-Redox Voltage Hysteresis in a Cation-Disordered Rock Salt Cathode

Pronounced voltage hysteresis in Li-excess cathode materials is commonly thought to be associated with oxygen redox. However, these materials often possess overlapping oxygen and transition-metal redox, whose contributions to hysteresis between charge and discharge are challenging to distinguish. In this work, a two-step aqueous redox titration is developed with the aid of mass spectrometry (MS) to quantify oxidized lattice oxygen and Mn 3+/4+ redox in a representative Li-excess cation-disordered rock salt—Li 1.2 Mn 0.4 Ti 0.4 O 2 (LMTO). Two MS-countable gas molecules evolve from two separate titrant-analyte reactions, thereby allowing Mn and O redox capacities to be decoupled. The decoupled O and Mn redox coulombic efficiencies are close to 100% for the LMTO cathode, indicating high charge-compensation reversibility. As incremental Mn and O redox capacities are quantitatively decoupled, each redox voltage hysteresis is further evaluated. Overall, LMTO voltage hysteresis arises not only from an intrinsic charge-discharge voltage mismatch related to O redox, but also from asymmetric Mn-redox overvoltages. The results reveal that O and Mn redox both contribute substantially to voltage hysteresis. In conclusion, this work further shows the potential of designing new analytical workflows to experimentally quantify key properties, even in a disordered material having complex local coordination environments.

25 ENERGY STORAGE↗
DOE OSTI2021

Interplay Between Cation and Anion Redox in Ni-Based Disordered Rocksalt Cathodes

The reversibility of the redox processes plays a crucial role in the electrochemical performance of lithium-excess cation-disordered rocksalt (DRX) cathodes. Here, we report a comprehensive analysis of the redox reactions in a representative Ni-based DRX cathode. The aim of this work is to elucidate the roles of multiple cations and anions in the charge compensation mechanism that is ultimately linked to the unique electrochemical performance of Ni-based DRX cathodes. Generally, the low-voltage discharge plateau that results in the low energy efficiency and strong voltage hysteresis is associated with the low-voltage oxygen redox. However, incorporating Mo cation promotes the oxygen activity and the Mo migration between octahedral and tetrahedral sites enhances the O reduction potential as well as energy efficiency. This work highlights the important role that electrochemically inactive transition metal plays in the redox chemistry and provides useful insights into the potential pathway to further address the challenges in Ni-based DRX systems.

Yue, Yuan↗
DOE OSTI2021

Role of Fluorine in Chemomechanics of Cation-Disordered Rocksalt Cathodes

The role of nanoscale chemomechanical behavior in the macroscopic performance of functional materials is well recognized. For lithium-ion battery cathodes, tremendous effort has been devoted to the development of new chemistry and structure, yet fundamental understanding of the correlation between redox processes and mechanical properties of the novel materials lags behind. In the present study, we prepare large discrete single grains of Li-excess cation-disordered rocksalts (DRX) and investigate their chemomechanical behavior at the particle level, using nanoresolution X-ray and electron-based spectro-imaging and chemical mapping techniques. While irregular cracking upon lithium extraction leads to the eventual breakdown of the baseline DRX oxide (Li 1.2 Ti 0.4 Mn 0.4 O 2 ) particles at a high delithiation state, the fluorinated-DRX (Li 1.3 Ti 0.3 Mn 0.4 O 1.7 F 0.3 ) clearly displays aligned cracking along the <001> direction. The resulting periodicity in the cracking pattern enables the particles to retain their integrity and, consequently, improved electrochemical stability. Density functional theory (DFT) calculations showed that fluorination leads to increased concentration of Li+ on the (001) planes and preferential Li movements along the <001>-family directions, revealing the underlying mechanism for directional cracking. Overall, our study demonstrates the unique role of fluorine in modulating nanoscale chemomechanics, which in turn influences the evolution of charge and strain heterogeneity at the particle level. These insights provide important design guidelines in further improving DRX cathode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Optimizing Li‐Excess Cation‐Disordered Rocksalt Cathode Design Through Partial Li Deficiency

Li-excess disordered rocksalts (DRXs) are emerging as promising cathode materials for Li-ion batteries due to their ability to use earth-abundant transition metals. In this work, a new strategy based on partial Li deficiency engineering is introduced to optimize the overall electrochemical performance of DRX cathodes. Specifically, by using Mn-based DRX as a proof-of-concept, it is demonstrated that the introduction of cation vacancies during synthesis (e.g., Li 1.3-x Mn 2+ 0.4-x Mn 3+ x Nb 0.3 O 1.6 F 0.4 , x = 0, 0.2, and 0.4) improves both the discharge capacity and rate performance due to the more favored short-range order in the presence of Mn3+. Density functional theory calculations and Monte Carlo simulations, in combination with spectroscopic tools, reveal that introducing 10% vacancies (Li 1.1 Mn 2+ 0.2 Mn 3+ 0.2 Nb 0.3 O 1.6 F 0.4 ) enables both Mn 2+ /Mn 3+ redox and excellent Li percolation. However, a more aggressive vacancy doping (e.g., 20% vacancies in Li 0.9 Mn 3+ 0.4 Nb 0.3 O 1.6 F 0.4 ) impairs performance because it induces phase separation between an Mn-rich and a Li-rich phase.

25 ENERGY STORAGE↗