Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cascading failures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Lightning Pin Injection Testing on MOSFETS

Lightning transients were pin-injected into metal-oxide-semiconductor field-effect transistors (MOSFETs) to induce fault modes. This report documents the test process and results, and provides a basis for subsequent lightning tests. MOSFETs may be present in DC-DC power supplies and electromechanical actuator circuits that may be used on board aircraft. Results show that unprotected MOSFET Gates are susceptible to failure, even when installed in systems in well-shielded and partial-shielded locations. MOSFET Drains and Sources are significantly less susceptible. Device impedance decreased (current increased) after every failure. Such a failure mode may lead to cascading failures, as the damaged MOSFET may allow excessive current to flow through other circuitry. Preliminary assessments on a MOSFET subjected to 20-stroke pin-injection testing demonstrate that Breakdown Voltage, Leakage Current and Threshold Voltage characteristics show damage, while the device continues to meet manufacturer performance specifications. The purpose of this research is to develop validated tools, technologies, and techniques for automated detection, diagnosis and prognosis that enable mitigation of adverse events during flight, such as from lightning transients; and to understand the interplay between lightning-induced surges and aging (i.e. humidity, vibration thermal stress, etc.) on component degradation.

Ely, Jay J.↗
NASA NTRS1983

A renormalization group model for the stick-slip behavior of faults

A fault which is treated as an array of asperities with a prescribed statistical distribution of strengths is described. For a linear array the stress is transferred to a single adjacent asperity and for a two dimensional array to three ajacent asperities. It is shown that the solutions bifurcate at a critical applied stress. At stresses less than the critical stress virtually no asperities fail on a large scale and the fault is locked. At the critical stress the solution bifurcates and asperity failure cascades away from the nucleus of failure. It is found that the stick slip behavior of most faults can be attributed to the distribution of asperities on the fault. The observation of stick slip behavior on faults rather than stable sliding, why the observed level of seismicity on a locked fault is very small, and why the stress on a fault is less than that predicted by a standard value of the coefficient of friction are outlined.

Smalley, R. F., Jr.↗
NASA NTRS1985

A renormalization group approach to the stick-slip behavior of faults

A fault which is treated as an array of asperities with a perscribed statistical distribution of strengths is described. For a linear array the stress is transferred to a single adjacent asperity and for a two dimensional array to three adjacent asperities. It is shown that the solutions bifurcate at a critical applied stress. At stresses less than the critical stress virtually no asperities fail on a large scale and the fault is locked. At the critical stress the solution bifurcates and asperity failure cascades away from the nucleus of failure. It is found that the stick slip behavior of most faults can be attributed to the distribution of asperities on the fault. The observation of stick slip behavior on faults rather than stable sliding, why the observed level of seismicity on a locked fault is very small, and why the stress on a fault is less than that predicted by a standard value of the coefficient of friction are outlined.

Smalley, R. F., Jr.↗
NASA NTRSDate not supplied

An Enhanced Model for Evaluating Failure Propagation in Launch Vehicle Engine Sections

An important component in the assessment of launch vehicle safety is the estimation of the likelihood of large-scale explosions given the existence of failures that manifest as a localized energy release. A failure propagation model is presented for simulating cascading failures of energetic components in proximity where the primary modes of energy transfer are fragments/shrapnel and blast overpressure. The model is an extension of the model developed by Mathias and Motiwala (2015) [1] with enhancements to include the effects of fragment ricochet, fragment drag, fragment ballistic limit equation thresholds, and blast impulse thresholds. A series of sensitivity studies were conducted for a generic launch vehicle engine section and results are presented that illustrate the effects of the model modifications.

Susie Go↗
NASA NTRSDate not supplied

An Enhanced Model for Evaluating Failure Propagation in Launch Vehicle Engine Sections

An important component in the assessment of launch vehicle safety is the estimation of the likelihood of large-scale explosions given the existence of failures that manifest as a localized energy release. A failure propagation model is presented for simulating cascading failures of energetic components in proximity where the primary modes of energy transfer are fragments/shrapnel and blast overpressure. The model is an extension of the model developed by Mathias and Motiwala (2015) [1] with enhancements to include the effects of fragment ricochet, fragment drag, fragment ballistic limit equation thresholds, and blast impulse thresholds. A series of sensitivity studies were conducted for a generic launch vehicle engine section and results are presented that illustrate the effects of the model modifications.

Susie Go↗
NASA NTRS2015

Simulation of Liquid Rocket Engine Failure Propagation Using Self-Evolving Scenarios

Traditional probabilistic risk assessment approaches often require failure scenarios to be explicitly defined through event sequences that are then quantified as part of the integrated analysis. This approach becomes difficult when failure propagation paths change as a function of the system operation. Additionally, if the propagation paths represent interactions among even a modest number of components, the scenario count becomes combinatorially intractable. This paper presents an alternate approach for quantifying the probability of failure propagation in such a case. Rather than explicitly defining scenario sequences, simple physical models are created for each of the components. In this way, only the physical states and rules of component interactions must be defined, rather than event sequences for each individual scenario. Initiating failures are introduced into the system, either randomly or as defined by relative likelihood, and the failures cascade through the system via the interaction rules. This process is repeated using Monte Carlo methods and, as a result, the most probable scenarios “self-evolve” in terms of both sequence path and frequency. This approach was applied to failures occurring in the engine compartment of a space launch vehicle with four liquid rocket engines and four high-pressure helium tanks. Each engine was modeled with key components, such as turbomachinery, combustion chamber, propellant lines, and additional support systems. Three test cases were conducted with different high-energy engine failures. End results of interest included an additional engine-out failure and tank burst, which represent the loss-of-mission (LOM) and loss-of-crew (LOC) failure environments, respectively. Observations show that almost every scenario outcome is unique and that many scenarios involve complex chain reactions that are difficult to predict. This validates the usefulness of the modeling approach in assessing the overall risks to the crew during a launch vehicle abort.

Rocket Engine↗
NASA NTRS1983

Productivity in an evolutionary space station

Space station productivity is treated from a systems point of view, considering the functions and attributes of space station development, formation, and operation that affect productivity. An optimum planning method is needed to assure that the station will have mission flexibility, technology advancement, maintainability, and evolutionary capability. Advanced technology will be designed into the housekeeping and utility functions of the station. Greater risk taking may be allowed into designs if the potential benefits of the advanced system support the risk, and if the system can be buffered from causing a failure cascade throughout the station. A common data base is needed to store and track all designs, developments, and changes in the station subsystems. Systems that can be automated and free the human inhabitants for more productive work are favored, as are modular components that are highly fault-free. Human control must also be possible, especially during check-out and verification, and also for teaching the automated systems new or modified tasks.

Anderson, J. L.↗
NASA NTRS2023

Technological and Medical Human Health and Well-Being Options in Deep Space

Zeroth order, maintenance of human health requires supportive protection from the hazards of space, including supplying breathable air, comfortable temperatures, a supportive diet/nutrition, radiation protection, and sufficient gravity to avoid the combinatorial impacts of such effecting human operability and health. Spacecraft operability must be “fail-safe” to ensure these basic human life support conditions are maintained throughout the mission and the mission(s) must be affordable. There are known effects and unknowns effects regarding aspects of human health for Mars duration missions. Mars has the order of a third g. We have no data regarding the health impacts of this on humans or the combinatorial effects associated with 45% GCR on the Martian surface over time. There is a suspicion that if humans survive such conditions over long times they will evolve to living at reduced g and become “Martians”. Cascading failures and subcritical degradations in systems of systems causing an overall unrecoverable failure are a potential issue. There are two exremely complex systems associated with humans-Mars missions: the technical, engineering, and architectural system of systems that enable the mission and the humans. Both need to be mutually configured and operated to mitigate the overall risks and hazards of the mission. Regarding the humans that mitigation includes both the mission risks and supporting-to-increasing the human immune and other concomitant physiological systems. This report will summarize the risks, current mitigation approaches, and putative approaches including lifestyle, nutrition, and “wellness” approaches to possibly improve the human capacity to withstand the large number of combinatorial human physiological rigors of the missions. The wellness observations also apply to and are derived from Earth terrestrial applicable research.

Dennis M Bushnell↗
NASA NTRS2001

Adjustable Autonomy Testbed

The Adjustable Autonomy Testbed (AAT) is a simulation-based testbed located in the Intelligent Systems Laboratory in the Automation, Robotics and Simulation Division at NASA Johnson Space Center. The purpose of the testbed is to support evaluation and validation of prototypes of adjustable autonomous agent software for control and fault management for complex systems. The AA T project has developed prototype adjustable autonomous agent software and human interfaces for cooperative fault management. This software builds on current autonomous agent technology by altering the architecture, components and interfaces for effective teamwork between autonomous systems and human experts. Autonomous agents include a planner, flexible executive, low level control and deductive model-based fault isolation. Adjustable autonomy is intended to increase the flexibility and effectiveness of fault management with an autonomous system. The test domain for this work is control of advanced life support systems for habitats for planetary exploration. The CONFIG hybrid discrete event simulation environment provides flexible and dynamically reconfigurable models of the behavior of components and fluids in the life support systems. Both discrete event and continuous (discrete time) simulation are supported, and flows and pressures are computed globally. This provides fast dynamic simulations of interacting hardware systems in closed loops that can be reconfigured during operations scenarios, producing complex cascading effects of operations and failures. Current object-oriented model libraries support modeling of fluid systems, and models have been developed of physico-chemical and biological subsystems for processing advanced life support gases. In FY01, water recovery system models will be developed.

Malin, Jane T.↗
NASA NTRS1980

A mathematical model of post-instability in continuum mechanics

The post-instability can appear in the form of failure of hyperbolicity or in the form of cascade instability (stretching of vorticity in an inviscid fluid or instability of the Navier-Stokes equations). All the cases are characterized by an unlimited decrease of the scale of the motions, in the course of which the derivatives of the corresponding functions tend to infinity, though the functions themselves remain finite. Such an instability shows that the corresponding state of a continuum cannot be properly simulated by smooth functions. Hence, the original model must be corrected by giving up the requirement about differentiability and enlarging the class of functions. Applications to a model of an inviscid fluid and to a model of turbulence are discussed.

Zak, M.↗
NASA NTRS2019

High Reliability Requires More than Providing Spares

It is sometimes optimistically hoped that a space life support system can be kept working throughout a long duration mission by repairing failed components, as long as sufficient spares are flown. It is usually assumed that the components have constant known failure rates. Then the needed numbers of spares can be computed to have any particular probability that all failed components can be replaced by available spares. This approach can provide high reliability if its favorable assumptions, including constant known failure rates, are satisfied. Other favorable assumptions are that the failures are statistically independent, repair will be successful without causing further failures, and all failures are due to internal component failures. These assumptions are not usually justified. The failure rates may be estimates that are inadequately verified because of insufficient testing. Failure rates may change due to materials substitutions, manufacturing changes, redesigns to fix failures, and new failures caused by redesigns. Failures that are not statistically independent may result from one common cause, such as a design or manufacturing error or a cascade of cause and effect, possibly caused by an external event such as a power outage. Repair may be unsuccessful or cause damage. Many failures occur at component interfaces or at the overall systems level, not within isolated components. Other failures causes are completely external to the system, due to assembly, maintenance, and operational errors or to unexpected environmental challenges. Replacement with sufficient spares can compensate for expected internal component failures but may not be able to cope with unpredictable design and manufacturing flaws, human errors, and environmental impacts. Reliability estimates based on providing sufficient spares to compensate for expected failures may be far too high. They are essentially upper bounds on reliability that might be approached if many frequent but often unconsidered failure causes can be eliminated.

spares↗
NASA NTRS1975

Cyclic stress analysis of an air-cooled turbine vane

The effects of gas pressure level, coolant temperature, and coolant flow rate on the stress-strain history and life of an air-cooled vane were analyzed using measured and calculated transient metal temperatures and a turbine blade stress analysis program. Predicted failure locations were compared to results from cyclic tests in a static cascade and engine. The results indicate that a high gas pressure was detrimental, a high coolant flow rate somewhat beneficial, and a low coolant temperature the most beneficial to vane life.

Kaufman, A.↗
NASA NTRS2020

Plant responses to rising vapor pressure deficit

Recent decades have been characterized by increasing temperatures worldwide, resulting in an exponential climb in vapor pressure deficit (VPD). VPD has been identified as an increasingly important driver of plant functioning in terrestrial biomes and has been established as a major contributor in recent drought‐induced plant mortality independent of other drivers associated with climate change. Despite this, few studies have isolated the physiological response of plant functioning to high VPD, thus limiting our understanding and ability to predict future impacts on terrestrial ecosystems. An abundance of evidence suggests that stomatal conductance declines under high VPD and transpiration increases in most species up until a given VPD threshold, leading to a cascade of subsequent impacts including reduced photosynthesis and growth, and higher risks of carbon starvation and hydraulic failure. Incorporation of photosynthetic and hydraulic traits in ‘next‐generation’ land‐surface models has the greatest potential for improved prediction of VPD responses at the plant‐ and global‐scale, and will yield more mechanistic simulations of plant responses to a changing climate. By providing a fully integrated framework and evaluation of the impacts of high VPD on plant function, improvements in forecasting and long‐term projections of climate impacts can be made.

mortality↗
NASA NTRS2025

HabSim: A Modular Coupled Virtual Testbed for Simulating ExtraTerrestrial Habitat Systems

Extraterrestrial habitats involve a tightly coupled combination of hardware, software, and humans while operating in an unforgiving environment that poses many risks, both anticipated and unanticipated. Traditional approaches with such systems of systems focus on reliability, robustness, and redundancy. These approaches seek to avoid failure rather than reduce overall risk. However, faults are inevitable, and understanding and managing the complex and emergent behavior and cascading events of such a complex system is critical. This study describes the development of HabSim, a computational simulation environment intended to support research to establish the know-how to design and operate resilient and autonomous SmartHabs. HabSim is a modular virtual testbed composed of many of the coupled dynamic systems expected in a typical SmartHab. A heterogeneous set of interconnected physics-based and phenomenological models is used to represent the essential functions of a SmartHab. HabSim further considers disruptions and models damage and repair of certain components. This paper discusses a) system and subsystem requirements of the deep space habitat included in the HabSim platform; b) architectural choices made in response to the requirements; c) technical considerations for developing, verifying, configuring, and executing HabSim; and d) illustrative sample results from a simulation of a representative disruption scenario.

Mohsen Azimi↗
NASA NTRS2000

Investigation of Flow Separation in a Transonic-fan Linear Cascade Using Visualization Methods

An extensive study into the nature of the separated flows on the suction side of modem transonic fan airfoils at high incidence is described in the paper. Suction surface.flow separation is an important flow characteristic that may significantly contribute to stall flutter in transonic fans. Flutter in axial turbomachines is a highly undesirable and dangerous self-excited mode of blade oscillations that can result in high cycle fatigue blade failure. The study basically focused on two visualization techniques: surface flow visualization using dye oils, and schlieren (and shadowgraph) flow visualization. The following key observations were made during the study. For subsonic inlet flow, the flow on the suction side of the blade is separated over a large portion of the blade, and the separated area increases with increasing inlet Mach number. For the supersonic inlet flow condition, the flow is attached from the leading edge up to the point where a bow shock from the upper neighboring blade hits the blade surface. Low cascade solidity, for the subsonic inlet flow, results in an increased area of separated flow. For supersonic flow conditions, a low solidity results in an improvement in flow over the suction surface. Finally, computational results modeling the transonic cascade flowfield illustrate our ability to simulate these flows numerically.

Lepicovsky, Jan↗
NASA NTRS2002

Fan Stall Flutter Flow Mechanism Studied

Modern turbofan engines employ a highly loaded fan stage with transonic or low-supersonic velocities in the blade-tip region. The fan blades are often prone to flutter at off-design conditions. Flutter is a highly undesirable and dangerous self-excited mode of blade oscillations that can result in high-cycle fatigue blade failure. The origins of blade flutter are not fully understood yet. Experimental data that can be used to clarify the origins of blade flutter in modern transonic fan designs are very limited. The Transonic Flutter Cascade Facility at the NASA Glenn Research Center was developed to experimentally study the details of flow mechanisms associated with fan flutter. The cascade airfoils are instrumented to measure high-frequency unsteady flow variations in addition to the steady flow data normally recorded in cascade tests. The test program measures the variation in surface pressure in response to the oscillation of one or more of the cascade airfoils. However, during the initial phases of the program when all airfoils were in fixed positions, conditions were found where significant time variations in the pressures near the airfoil leading edges could be observed.

Lepicovsky, Jan↗
NASA NTRS1986

Star of Lima - Overview and optical diagnostics of a barium Alfven critical velocity experiment

The Alfven critical velocity mechanism for ionization of a neutral gas streaming across the magnetic field has been demonstrated in laboratory experiments. In March 1983, two rocket-borne experiments with Ba and Sr tested the effect in the wall-less laboratory of space from Punto Lobos, Peru, near 430 km altitude. 'Star of Lima' used a conical Ba shaped charge aimed at an instrument payload about 2 km away. Because of rocket overperformance the detonation occurred in partial sunlight, so that less than 21.6 percent of the ionizing UV was present. Particle and field measurements indicate the production of hot electrons and waves in the energy and frequency range that are respectively predicted to produce a cascade of ionization by the Alfven mechanism. However, the ionization fluxes and wave energy density did not reach cascade levels, and optical observations indicate that only 2.5 to 5 x 10 to the 20th Ba ions were produced. A substantial portion and perhaps all of the ionization could have been produced by solar UV. The failure of the Alfven process in this experiment is not well understood.

Wescott, E. M.↗