Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “carbon fiber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Development of fiber orientation in injection molding: Comparison of glass fiber, carbon fiber and their hybrid composites

Fiber orientation distribution (FOD) in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for glass fiber (GF), carbon fiber (CF), and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varied with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of Oxygen Uptake on Pitch Carbon Fiber

Carbon fiber precursor materials, such as polyacrylonitrile, pitch, and cellulose/rayon, require thermal stabilization to maintain structural integrity during conversion into carbon fiber. Thermal stabilization mitigates undesirable decomposition and liquification of the fibers during the carbonization process. Generally, the thermal stabilization of mesophase pitch consists of the attachment of oxygen-containing functional groups onto the polymeric structure. In this study, the oxidation of mesophase pitch precursor fibers at various weight percentage increases (1, 3.5, 5, 7.5 wt%) and temperatures (260, 280, 290 °C) using in situ differential scanning calorimetry and thermogravimetric analysis is investigated. The results are analyzed to determine the effect of temperature and weight percentage increase on the stabilization process of the fibers, and the fibers are subsequently carbonized and tested for tensile mechanical performance. Finally, the findings provide insight into the relationship between stabilization conditions, fiber microstructure, and mechanical properties of the resulting carbon fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Comparative Analysis of Radial and Random Microstructures of Mesophase Pitch Carbon Fibers

Carbon fibers (CF) with radial and random microstructures are produced. Here, these fibers are subjected to identical treatment before being mechanically tested and analyzed with Weibull analysis, with the results revealing a statistically significant difference in tensile strengths of 2.23 GPa for random CF and 1.69 GPa for radial CF. Raman mapping probed the crystalline structure perpendicular to the fiber axis and found a uniform structure, while wide‐angle X‐ray diffraction showed a significant difference of 7.5 Å in the crystallites’ basal lengths parallel to the fiber. Small‐angle X‐ray scattering is completed parallel to the fiber for the first time. A cross‐section Guinier plot of the 1D azimuthal integration is generated assuming symmetric scattering, and the parallel scatterers are found to have a similar length scale to the crystallite's length, validating the testing method. Finally, transmission electron microscopy is completed on the longitudinal cross‐section of each fiber. The radial carbon fiber is found to have a core–shell structure, as evidenced further by fast Fourier transform images. Through all studies, it is shown that the structure developed during mesophase pitch spinning altered the microstructure, thus impacting the mechanical properties, confirming a direct relationship between processing, structure, and properties.

Scherschel, Alexander [Univ. of Virginia, Charlott↗
DOE OSTI2015

Method for the preparation of carbon fiber from polyolefin fiber precursor, and carbon fibers made thereby

Methods for the preparation of carbon fiber from polyolefin fiber precursor, wherein the polyolefin fiber precursor is partially sulfonated and then carbonized to produce carbon fiber. Methods for producing hollow carbon fibers, wherein the hollow core is circular- or complex-shaped, are also described. Methods for producing carbon fibers possessing a circular- or complex-shaped outer surface, which may be solid or hollow, are also described.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Aligned carbon fibers-carbon nanotube-polymer-based composite as lithium-ion battery current collector

High energy density demand is pushing the development of high-voltage cathode materials, which necessitates improved electrochemical stability of other battery components such as binders, electrolytes, and current collectors. Current collectors are considered to be an inactive component but still play an essential role. In this study, a metal-free composite film containing directionally aligned carbon fiber (CF), carbon nanotube (CNT), and polymer (P) was developed to replace aluminum foil as a cathode current collector, which relies on forming an Al 2 O 3 layer to ensure electrochemical stability at high voltage. Here, each component in the new cathode current collector played a functional role. The CNTs provided uniform current densities, and CFs improved the electronic conductivity and mechanical strength of the composite material. The polymer enhanced the adhesion of the cathode coating with the current collector and provided an impervious support to the cathode materials. The CF-CNT-P composite demonstrated excellent electrochemical and thermal stability. Cathodes coated on the CF-CNT-P composite exhibited lower charge transfer resistance, improved rate capability, and improved cyclic stability compared with the cathodes deposited on conventional aluminum foil. Additionally, the composite current collector was lighter (1.81 mg/cm 2 and 15 µm thick) than the commonly used aluminum foil (4.35 mg/cm2 and 15 µm thick), which can increase the cell energy density. Additionally, the CF-CNT-P did not need to be separated from the cathode coating during recycling and can be burnt out with binder, simplifying the recycling process.

25 ENERGY STORAGE↗
DOE OSTI2024

3D printed carbon fiber reinforced carbon as an energy efficient alternative to graphite for EFAS tooling

As Electric Field Assisted Sintering (EFAS) gains more industrial acceptance and use, it becomes more important to develop more efficient means to implement this technology. To this aim, 3D printed continuous carbon fiber reinforced carbon (CCC) was manufactured and fabricated into tooling for EFAS systems as an alternative to traditional graphite tooling. The impact of fiber orientation on the thermal and electrical properties of the CCC was characterized. Sample material was sintered in Tokai G535 graphite tooling, under common processing conditions and compared with CCC tooling. There was nearly 50 % energy savings compared to graphite while maintaining equivalent sample density and microstructure plus keeping ram temperatures 39 % cooler. This is due to spatial control of generated heat and thermal diffusivity within the molds, by means of fiber orientation anisotropy. Finite element modeling of the tooling design supported the experimental results as well as displays the effect of optimization of this 3D printed CCC material.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Local conformations and heterogeneities in structures and dynamics of isotactic polypropylene adsorbed onto carbon fiber

Carbon fiber (CF) reinforced polymers (CFRPs) have experienced widespread use in various industries. One of the most important parameters that controls the macroscopic property of CFRPs is the interface between a polymer matrix and CF. There is growing evidence to suggest the formation of a bound polymer layer (BPL), i.e., polymer chains that physically adsorb on a filler surface. However, this interface is always in contact with the thicker part of a polymer matrix, rendering its understanding a difficult task. Therein, we use CF-reinforced isotactic polypropylene (iPP) as a rational CFRP. To characterize the BPL on the CF surface, we extracted it from the CFRP using solvent-rinsing with p-xylene. The physical and thermal properties of the BPL were characterized by differential scanning calorimetry and thermogravimetric analysis, while its microscopic structures and dynamics were probed by small-angle neutron scattering and quasi-elastic neutron scattering (QENS) techniques. Subsequently, we employed atomistic molecular dynamics (MD) simulations to complement the QENS results above the bulk melting temperature and reveal details that were experimentally inaccessible. In this work, we observed that the degree of crystallinity of the BPL was quite lower than the bulk, while the melting temperature of the BPL remained the same as the bulks. Within the given length and time scales probed by QENS and MD, we also observed that most of the bound chains were mobile, with the formation of a high-density region (less than 1 nm in thickness) near the CF surface. The segmental dynamics of the bound chains probed by both QENS and MD were also much faster than those of the free chains, possibly due to the presence of a free surface region at the topmost surface of the BPL. Furthermore, the MD results demonstrated that the backbone chains and side groups lie nearly flat on the CF surface, which is the driving force for the flattening process of the iPP BPL to overcome the conformational entropy loss in the total free energy.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Two-step sulfonation process for the conversion of polymer fibers to carbon fibers

Disclosed herein are processes for preparing carbon fibers, comprising: sulfonating a polymer fiber with a sulfonating agent that is fuming sulfuric acid, sulfuric acid, chlorosulfonic acid, or a combination thereof; treating the sulfonated polymer with a heated solvent, wherein the temperature of the heated solvent is at least 95.degree. C.; and carbonizing the resulting product by heating it to a temperature of 501-3000.degree. C. Carbon fibers prepared according to these methods are also disclosed herein.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Lightweight, Flexible Electromagnetic Shielding Composite Films Reinforced with Recycled Carbon Fibers and Carbon Nanofillers

Lightweight, flexible polymer composites are widely adopted in modern electronic devices and systems for high-efficiency electromagnetic interference (EMI) shielding. Reinforcing polymer composites with conductive fillers offers a promising alternative to conventional metal-based shielding material thanks to their low density, tunable properties, and flexibility. Herein, lightweight, flexible ultra-high molecular weight polyethylene composite films reinforced with recycled carbon fibers (rCFs) and carbon-based nanofillers, including graphene nanoplatelets (GNPs) and carbon nanotubes, are reported for EMI shielding applications. The incorporation of these nanofillers significantly reduces the required content of rCFs and improves processability while maintaining comparable shielding effectiveness. The addition of these nanofillers with rCFs enhances the EMI shielding effectiveness by up to 15 dB. Incorporating 1 wt% GNPs can replace 5 wt% rCFs and achieve comparable EMI shielding performance, while 5 wt% of either nanofillers can substitute for 10 wt% rCFs. Numerical modeling of electromagnetic wave transmission reveals that increasing nanofiller concentrations enhances both reflection and absorption losses, with absorption consistently dominating across all levels. Furthermore, this study not only provides insight into the synergistic contributions of rCFs and carbon nanofillers to shielding effectiveness but also paves the way for the design of sustainable, lightweight EMI shielding composite films for applications in electric vehicles, medical equipment, and portable electronics.

carbon nanofiller↗
DOE OSTI2023

3D Printed Carbon Fiber Reinforced Carbon: An energy efficient alternative to graphite EFAS tooling

Carbon fiber preforms are printed in a Quasi-Isotropic layup, where the fibers are aligned to the X and Y axes, and ±45° in plane. Thermal and electrical conductivity values along the fiber axes are comparable to graphite but are extremely low through the Z axis. Low conductivity (high resistivity) in the axis of current flow enables more efficient Joule heating.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Converting PBO fibers into carbon fibers by ultrafast carbonization

Here, we report an ultrafast transformation of poly(p-phenylene-2,6-benzobisoxazole) (PBO) fibers into car- bon fibers (CFs) by direct carbonization that eliminates high-cost oxidation in traditional CF conversion. Ultrafast heating and cooling render PBO-derived CFs superlative mechanical properties. ReaxFF atomistic-scale reactive molecular dynamics simulations unveil the PBO to CF conversion mechanism in which ultrafast heating suppresses the O-contained gas release, facilitating all-carbon rings alignment during the carbonization of PBO. These results offer new guidelines for identifying and evaluating alternative CF precursors and fresh perspectives on smart manufacturing of CFs.

42 ENGINEERING↗
DOE OSTI2017

Quality carbon fibers from fractionated lignin

The application of lignin carbon fibers was hindered by their low quality and mechanical performance. We addressed this challenge by developing a new approach to fractionate and modify lignin to produce quality carbon fibers using an enzyme-mediator system, which derives lignin fractions with different molecular weights, functional groups, and interunitary linkages. The fractionated lignin in general improves the miscibility and spinnability of lignin. In particular, the insoluble lignin fraction renders carbon fibers with a significantly improved turbostratic carbon structure as revealed by XRD and Raman spectroscopy. The improvement in the carbon structure leads to the significantly improved elastic modulus. The results suggest that higher molecular weights, less –OH groups, and more linear structures may contribute to the improved crystallization and mechanical performance of lignin carbon fibers. Finally, the technical breakthrough produces lignin-based carbon fibers with a similar elastic modulus to commercial carbon fibers for the first time, and paves the path for replacing PAN with lignin for producing quality carbon fibers.

Enzymatic fractionation↗
DOE OSTI2017

Magneto-carbonization method for production of carbon fiber, and high performance carbon fibers made thereby

Method for the preparation of carbon fiber from fiber precursor, wherein the fiber precursor is subjected to a magnetic field of at least 3 Tesla during a carbonization process. The carbonization process is generally conducted at a temperature of at least 400.degree. C. and less than 2200.degree. C., wherein, in particular embodiments, the carbonization process includes a low temperature carbonization step conducted at a temperature of at least or above 400.degree. C. or 500.degree. C. and less than or up to 1000.degree. C., 1100.degree. C., or 1200.degree. C., followed by a high temperature carbonization step conducted at a temperature of at least or above 1200.degree. C. In particular embodiments, particularly in the case of a polyacrylonitrile (PAN) fiber precursor, the resulting carbon fiber may possess a minimum tensile strength of at least 600 ksi, a tensile modulus of at least 30 Msi, and an ultimate elongation of at least 1.5%.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Molecular weight and uniformity define the mechanical performance of lignin-based carbon fiber

Lignin-based carbon fiber represents a renewable and low-cost alternative to petroleum-based carbon fiber. However, the poor mechanical performance of current lignin carbon fiber hinders its application. We hypothesized that the lower optimal mechanical performance is caused by the inherent heterogeneity of lignin. It is still unknown how the molecular weights (MWs) and lignin uniformity will impact the performance of lignin carbon fiber. We thereby addressed this hypothesis by fractionating lignin into fractions with different MWs and polydispersity indices (PDIs). An enzyme–mediator-based method and a dialysis method were developed to derive lignin fractions with increased MW and decreased PDI. Lignin fractions were electro-spun into fibers after blending with polyacrylonitrile (PAN) at 1 : 1 (w/w) ratio. The fractionation in general improved the spinnability of lignin to allow us to obtain finer lignin-based carbon fibers. The elastic modulus of lignin carbon fibers, as measured by nanoindentation, was increased as the lignin MW increased and as PDI decreased. The scatter plot and linear regression revealed very good correlation between the elastic modulus and PDI, as well as certain correlation between the elastic modulus and MW. XRD and Raman spectroscopy revealed that the crystallite size and the content of the pre-graphitic turbostratic carbon increased with higher lignin MW and lower PDI, revealing the mechanism of the improvement in carbon fiber mechanical performance. Finally, this study elucidated the impacts of lignin MW and uniformity on the mechanical properties of carbon fiber, and could thus guide the development of lignin processing technologies for quality lignin-based carbon fiber.

09 BIOMASS FUELS↗
DOE OSTI2019

Fiber motion in highly confined flows of carbon fiber and non-Newtonian polymer [Advanced modeling of non-Newtonian polymer and carbon fibers]

Inks compounded of short carbon fibers suspended in polymer resin can be extruded to produce composite materials during additive manufacturing or 3D printing processes. The flow process induces anisotropic orientation of the fibers which is set into the matrix and significantly affects the mechanical and physical properties of the final product. Therefore, the flow of fiber suspensions needs to be understood in order to predict the orientation distribution of the fibers during such manufacturing processes. There is still a lack of knowledge for extrusion of the complex mixture of a non-Newtonian polymer containing a high-volume fraction of fibers with high fiber aspect ratio, where both inter-particle, fluid-particle and fiber-wall interactions are computationally evaluated. This paper presents predictive numerical simulations and experimental results of such confined flow in a concentrated regime. The code is based on Lagrange multiplier technique and resolves each particle and interaction between the fibers and surrounding fluid and nozzle walls. We investigate numerically how the fiber length impacts the fiber alignment during extrusion. We found that a fiber length above 67% of the nozzle's diameter induces dramatic change in the fiber flow, causing fibers to concentrate at the nozzle boundaries with very low concentration of fibers in the center of the nozzle. It was found that the best fiber alignment is reached for fiber lengths equal to 40–50% of the nozzle diameters. Numerical findings are supported by experimental results. In conclusion, this work improves understanding of fiber orientation during 3D printing and is an important milestone for the prediction of the complex mechanical properties of additively manufactured fiber composites.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Controlled chemical stabilization of polyvinyl precursor fiber, and high strength carbon fiber produced therefrom

Method for the preparation of carbon fiber, which comprises: (i) immersing functionalized polyvinyl precursor fiber into a liquid solution having a boiling point of at least 60.degree. C.; (ii) heating the liquid solution to a first temperature of at least 25.degree. C. at which the functionalized precursor fiber engages in an elimination-addition equilibrium while a tension of at least 0.1 MPa is applied to the fiber; (iii) gradually raising the first temperature to a final temperature that is at least 20.degree. C. above the first temperature and up to the boiling point of the liquid solution for sufficient time to convert the functionalized precursor fiber to a pre-carbonized fiber; and (iv) subjecting the pre-carbonized fiber produced according to step (iii) to high temperature carbonization conditions to produce the final carbon fiber. Articles and devices containing the fibers, including woven and non-woven mats or paper forms of the fibers, are also described.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Comparison of ORNL Low Cost Carbon Fiber with Commercially Available Industrial Grade Carbon Fiber in Pultrusion Samples

Composite Applications Group LLC in collaboration with Heil Trailer International partnered in a project to design and develop solutions for light weighting of aluminum dry bulk tank trailers. The project approach was to utilize pultruded composite sections in place of aluminum components to reduce weight thereby saving energy through more efficient transport. Low cost carbon fiber was evaluated as a potential cost saving option that could enhance weight savings at reduced cost versus current commercial material.

36 MATERIALS SCIENCE↗