Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “capillary discharge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Creation of an axially uniform plasma channel in a laser-assisted capillary discharge

Dissipative capillary discharges form plasma channels which allow for high power laser guiding, enabling efficient electron acceleration in a laser wakefield accelerator. However, at the low plasma densities required to produce high-energy electrons, in order to avoid capillary wall damage, high power lasers need a tighter transverse confinement that cannot be achieved by the capillary discharge powered by Ohmic heating alone. The introduction of an additional laser for heating of the plasma leads to deeper and narrower plasma channels. Here we investigate the formation of laser-heated axially uniform plasma channels. Here, we show that a high degree of longitudinal uniformity can be achieved despite significant evolution of the heater laser during its propagation through the channel.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Radial density profile and stability of capillary discharge plasma waveguides of lengths up to 40 cm

We measured the parameter reproducibility and radial electron density profile of capillary discharge waveguides with diameters of 650 μm to 2 mm and lengths of 9 to 40 cm. To the best of the authors’ knowledge, 40 cm is the longest discharge capillary plasma waveguide to date. This length is important for ≥10 GeV electron energy gain in a single laser-driven plasma wakefield acceleration stage. Evaluation of waveguide parameter variations showed that their focusing strength was stable and reproducible to <0.2% and their average on-axis plasma electron density to <1%. These variations explain only a small fraction of laser-driven plasma wakefield acceleration electron bunch variations observed in experiments to date. Measurements of laser pulse centroid oscillations revealed that the radial channel profile rises faster than parabolic and is in excellent agreement with magnetohydrodynamic simulation results. We show that the effects of non-parabolic contributions on Gaussian pulse propagation were negligible when the pulse was approximately matched to the channel. However, they affected pulse propagation for a non-matched configuration in which the waveguide was used as a plasma telescope to change the focused laser pulse spot size.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Density Tailored Capillary Discharge (Final Technical Report)

This final report describes efforts to validate a novel way to drive capillary discharges in order to achieve true matched guiding of a focused laser beam traveling along the capillary. Achieving such matched guiding is important for laser plasma accelerators, such as ones based upon laser wakefield acceleration. During this Phase II program, a computer model, which was specifically designed to predict the time-dependent behavior of the capillary discharge, was exercised to determine whether unconventional ways to drive the discharge may yield matched guiding. A custom power supply was built to drive the capillary discharge in the unconventional manner specified by the model. Experiments performed at STI Optronics seemed to support the predictions of this model; however, subsequent more accurate measurements performed at Lawrence Berkeley National Laboratory did not agree with the model predictions.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Laser-heated capillary discharge plasma waveguides for electron acceleration to 8 GeV

A plasma channel created by the combination of a capillary discharge and inverse Bremsstrahlung laser heating enabled the generation of electron bunches with energy up to 7.8 GeV in a laser-driven plasma accelerator. The capillary discharge created an initial plasma channel and was used to tune the plasma temperature, which optimized laser heating. Although optimized colder initial plasma temperatures reduced the ionization degree, subsequent ionization from the heater pulse created a fully ionized plasma on-axis. The heater pulse duration was chosen to be longer than the hydrodynamic timescale of ≈ 1 ns, such that later temporal slices were more efficiently guided by the channel created by the front of the pulse. Here, simulations are presented which show that this thermal self-guiding of the heater pulse enabled channel formation over 20 cm. The post-heated channel had lower on-axis density and increased focusing strength compared to relying on the discharge alone, which allowed for guiding of relativistically intense laser pulses with a peak power of 0.85 PW and wakefield acceleration over 15 diffraction lengths. Electrons were injected into the wake in multiple buckets and times, leading to several electron bunches with different peak energies. To create single electron bunches with low energy spread, experiments using localized ionization injection inside a capillary discharge waveguide were performed. A single injected bunch with energy 1.6 GeV, charge 38 pC, divergence 1 mrad, and relative energy spread below 2% full-width half-maximum was produced in a 3.3 cm-long capillary discharge waveguide. This development shows promise for mitigation of energy spread and future high efficiency staged acceleration experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Laser-heated capillary discharge waveguides as tunable structures for laser-plasma acceleration

Laser-heated capillary discharge waveguides are novel, low plasma density guiding structures able to guide intense laser pulses over many diffraction lengths and have recently enabled the acceleration of electrons to 7.8 GeV by using a laser-plasma accelerator (LPA). These devices represent an improvement over conventional capillary discharge waveguides, as the channel matched spot size and plasma density can be tuned independently of the capillary radius. This has allowed the guiding of petawatt-scale pulses focused to small spot sizes within large diameter capillaries, preventing laser damage of the capillary structure. High performance channel-guided LPAs require control of matched spot size and density, which experiments and simulations reported here show can be tuned over a wide range via initial discharge and laser parameters. In this paper, measurements of the matched spot size and plasma density in laser-heated capillary discharges are presented, which are found to be in excellent agreement with simulations performed using the MHD code MARPLE. Strategies for optimizing accelerator performance are identified based on these results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Impact of electron transport models on capillary discharge plasmas

Magnetohydrodynamics (MHD) can be used to model capillary discharge waveguides in laser-wakefield accelerators. However, the predictive capability of MHD can suffer due to poor microscopic closure models. Here, we study the impact of electron heating and thermal conduction on the capillary waveguide performance as part of an effort to understand and quantify uncertainties in modeling and designing next-generation plasma accelerators. To do so, we perform two-dimensional high-resolution MHD simulations using an argon-filled capillary discharge waveguide with three different electron transport coefficients models. The models tested include (i) Davies et al., (ii) Spitzer, and (iii) Epperlein–Haines (EH). We found that the EH model overestimates the electron temperature inside the channel by over 20% while predicting a lower azimuthal magnetic field. Furthermore, the Spitzer model, often used in MHD simulations for plasma-based accelerators, predicts a significantly higher electron temperature than the other models suggest.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Scaling of pulsed nanosecond capillary plasmas at different specific energy deposition

Nano-second, capillary discharges (nCDs) are unique plasma sources in their ability to sustain high specific energy deposition ω dep approaching 10 eV/molecule in molecular gases. This high energy loading on short timescales produces both high plasma densities and high densities of molecular exited states. These high densities of electrons and excited states interact with each other during the early afterglow through electron collision quenching and associative ionization. In this paper we discuss results from a two-dimensional computational investigation of a nCD sustained in air at a pressure of 28.5 mbar and with a voltage amplitude 20 kV. Discharges were investigated for two circuit configurations—a floating low voltage electrode and with the low voltage electrode connected to ground through a ballast resistor. The first configuration produced a single ionization wave from the high to low voltage electrode. The second produced converging ionization waves beginning at both electrodes. With a decrease of the tube radius, the velocity of the ionization fronts decreased while the shape of the ionization wave changed from the electron density being distributed smoothly in the radial direction, to being hollow shaped where there is a higher electron density near the tube wall. For sufficiently small tubes, the near-wall maxima merge to have the higher density on the axis of the capillary tube. In the early afterglow, the temporal and radial behavior of the N 2 (C 3 Π u ) density is a sensitive function of ω dep due to electron collision quenching. Finally, these trends indicate that starting from ω dep $\geqslant$ 0.3 eV/molecule, it is necessary to take into account interactions of electrons with electronically excited species during the discharge and early afterglow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Whitepaper submitted to Snowmass21: Advanced accelerator linear collider demonstration facility at intermediate energy

It is widely accepted that the next lepton collider beyond a Higgs factory would require center-of-mass energy of the order of up to 15 TeV. Since, given reasonable space and cost restrictions, conventional accelerator technology reaches its limits near this energy, high-gradient advanced acceleration concepts are attractive. Advanced and novel accelerators (ANAs) are leading candidates due to their ability to produce acceleration gradients on the order of 1--100~GV/m, leading to compact acceleration structures. Over the last 10-15 years significant progress has been achieved in accelerating electron beams by ANAs. For example, the demonstration of several-GeV electron beams from laser-powered capillary discharge waveguides, as well as the proof-of-principle coupling of two accelerating structures powered by different laser pulses, has increased interest in ANAs as a viable technology to be considered for a compact, TeV-class, lepton linear collider. However, intermediate facilities are required to test the technology and demonstrate key subsystems. A 20-100 GeV center-of-mass energy ANA-based lepton collider can be a possible candidate for an intermediate facility. Apart from being a test beam facility for accelerator and detector studies, this collider will provide opportunities to study muon and proton beam acceleration, investigate charged particle interactions with extreme electromagnetic fields (relevant for beam delivery system designs and to study the physics at the interaction point), as well as precision Quantum Chromodynamics and Beyond the Standard Model physics measurements. Possible applications of this collider include the studies of $\gamma\gamma$ and $e$-ion collider designs.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Experimental characterization of discharge plasma dynamics in a square capillary for prospective applications in laser wakefield acceleration

Research on plasma generated by electrical discharge in gas-filled capillaries plays an important role in advancing laser wakefield accelerators. We present a comprehensive study of the temporal and spatial distribution of plasma density within a short, 1 cm long, square-shaped capillary filled with hydrogen gas. Two transverse capillary sizes, 500 μm and 300 μm, were investigated achieving peak plasma densities of 0.9 × 10 18 cm −3 and 2.5 × 10 18 cm −3 , respectively, at the capillary center. In addition, we explore how these distributions depend on discharge parameters, specifically discharge current and gas flow through the capillary. Plasma density was determined by analyzing the Stark broadening of the hydrogen Balmer-alpha line. The results obtained were compared with the theoretical models and simulations. The comparison between the model predictions and the experimental data at the transient ionization stage of the discharge reveals a discrepancy of a factor of ∼1.3–2.1, depending on the capillary size, which is thoroughly discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Reconfiguration of an Electrothermal-Arc Plasma Source for In Situ PMI Studies

An electrothermal-arc plasma source (ET-Arc) has been developed to produce transient plasma heat and particle fluxes similar to those produced by edge localized modes onto divertor plasma-facing components in tokamaks. The ET-Arc utilizes a capacitive discharge to send current through a 4-mm-diameter, 9-cm-long capillary source liner. The liner material is ablated to form a high-velocity plasma jet that impacts the target downstream. With the current discharge circuit configuration, pulse lengths are 1 to 2 ms in duration and deliver heat fluxes of 0.25 to 2.1 GW m-2. The plasma was previously characterized with optical emission spectroscopy (OES) on helium emission lines. The He I line ratios were interpreted with collisional radiative analysis to calculate ne and Te. The electron temperature and electron density ranged from Te = 1 to 5 eV and ne = 1022 to 1028 electrons/m3, respectively.

Lindquist, Elizabeth G.↗
DOE OSTI2026

Testing of spark plasma sintered porous tungsten under neon glow discharge cleaning conditions in LTX-β

This paper demonstrates that tungsten (W) based powder reconstituted Plasma Facing Components (PFCs) can be treated in situ in a fusion reactor to remove W oxide and carbon (C) contamination. Doing so should ease the challenge of using these materials in a Capillary Porous System (CPS) with lithium (Li) by enabling better wetting and less contamination of the Li by the underlying CPS. Most powder reconstituted materials including 3D printed and sintered PFCs suffer from a high surface contamination from oxides and surface C, which complicates their use with liquid Li, a primary PFC candidate. Spark plasma sintered porous W samples were fabricated to be used as a CPS with liquid Li. The samples were characterized in terms of morphology and surface chemistry. Analysis confirms a high C and oxygen (O) contamination. We present the results of exposing this type of CPS to Glow Discharge Cleaning (GDC) cycles in the Lithium Tokamak Experiment-β (LTX-β). The sample was exposed to neon (Ne) GDC in the midplane of the low-field side of LTX-β and analyzed in vacuo with Temperature Programmed Desorption (TPD) and Secondary Ion Mass Spectrometry (SIMS) to investigate the effects the Ne GDC had on the chemical composition of the sample. The combination of Ne GDC with rapid heating as done in TPD was successful in reducing the W oxides and removing the C contamination.

Capillary porous system↗
DOE OSTI2021

Atmospheric-pressure ionization and fragmentation of molecules for structural elucidation

A solution-cathode glow discharge mass spectrometry (SCGD-MS) apparatus comprises a SCGD source and a mass spectrometer. The SCGD source may comprise conductive rods, a power source, and a capillary. A method for ionizing an analyte comprises flowing an electrically conductive liquid onto a conductive rod, applying an electric potential to a second conductive rod such that a plasma discharge forms between the first conductive rod and the electrically conductive liquid to produce ions, and separating the ions in a mass spectrometer. The analyte may be a polypeptide that may be contacted with trypsin. The analyte may be a solid, liquid, gas, chemical complex, or ion in solution. The method may comprise sequencing the polypeptide.

Shelley, Jacob T.↗
DOE OSTI2020

Numerical simulation of an atmospheric pressure plasma jet with coaxial shielding gas

A two-dimensional ( r, z ) numerical simulation of the discharge characteristics of an atmospheric pressure plasma jet (APPJ), with coaxial shielding gas, was performed. The helium working gas flowed in a central capillary tube, engulfing a needle electrode powered by 13.7 MHz radio frequency sinusoidal voltage. The N 2 shielding gas flowed in the annular space of a coaxial tube. These gases emerged, in laminar flow, in a 78%N 2 -21%O 2 -1%Ar dry air ambient. The characteristics of the APPJ with shielding gas were compared to those of the APPJ without shielding gas. The nitrogen shielding gas hindered the diffusion of oxygen and argon from the ambient air into the helium jet. With the shielding gas present, more nitrogen penetrated into the helium core, causing a shorter plasma ‘plume’. The flow rates of the working and shielding gas, critically affected the gas temperature, and in turn the discharge characteristics. For a He flow of 2 standard liters per minute (slm), switching on the nitrogen shielding gas flow (at 4.5 slm) reduced the on-axis O 2 and Ar mole fractions from 3.9 × 10 - 4 to 6.8 × 10 - 5 and from 1.9 × 10 - 5 to 3.3 × 10 - 6 , respectively, at an axial distance of 3 mm downstream of the nozzle. The radial profiles of the mole fractions of the ambient gases were monotonically and strongly decreasing towards the system axis, for short axial distances from the nozzle (~1 mm), but became progressively flatter at longer distances from the nozzle (3 mm and 5 mm). Simulation predictions captured the salient features of experimental data of ambient species mole fractions in the plasma jet, and the 706 nm optical emission intensity profiles of the He 3 3 S excited state.

Physics↗
DOE OSTI2026

Overview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D

Characterization and testing of advanced plasma-facing materials (PFMs) for Fusion Pilot Plants (FPP) is being conducted at the DIII-D National Fusion Facility through the ongoing two-year FPP Candidate Materials Thrust. Year one tested 17 novel materials utilizing the Divertor Materials Evaluation System (DiMES), with samples analyzed pre- and post-experiment via SEM, EDS, and confocal microscopy. Repeatable reference discharges were developed to ensure uniformity between experiments, including a new strike-point rastering scenario to provide more uniform heat/particle flux across DiMES during ELMing H-mode discharges. Various sample geometries and temperatures were used to achieve FPP-relevant conditions, including samples angled 10° towards the incident plasma flux and pre-heating up to 500 °C. The first exposure of liquid lithium (Li) capillary porous structures in a tokamak demonstrated uniform emission of Li vapor and suppression of Li droplets in H-mode when preheated to 350 °C. Dispersoid-strengthened W with 1 wt% TaC, TiC, and ZrC exposed to H-mode showed cracking and dispersoid ejection for all varieties except TiC, providing a clear down-selection. Ultra-high temperature ceramic materials TiB 2 and ZrB 2 showed minimal degradation under L-mode exposure. Silicon carbide (SiC) fiber composites showed arcing along edges, while CVD SiC remained pristine. Atmospheric plasma-sprayed W and SiC coatings endured H-mode exposure without macroscopic delamination; SiC exhibited granular ejection, while W showed increased outgassing. Additional W-based alloys were stress tested in H-mode, including Ni-based W heavy alloys, W f SiC f /W composites, W multi-principle element alloys, and functionally-graded W/SiC, to varying degrees of success.

DIII-D↗
DOE OSTI2025

Surface deformation coupled with self-organized pattern on a liquid anode of 1 atm DC glow discharge

Intricate, self-organized plasma structures observed above the surface of a liquid anode of atmospheric DC glow discharge were found to give rise to coherent, organized surface deformation and mechanical wave formation at the plasma–liquid interface. This new phenomenon indicates that the liquid is closely coupled to the plasma by the anode sheath’s electrohydrodynamic (EHD) force. A scientific question then arises: Do surface perturbations, coupled with the nonuniform surface charge distribution, enhance the electric field and induce self-organization? Using the reflective background-oriented schlieren technique, the liquid surface profile under the plasma pattern was measured for the first time. The results show that surface distortions are driven by the repulsive Coulomb force of nonuniform net-negative surface charge acted by the anode sheath field. The impacts of various operating parameters on the patterns and surface waves were examined, revealing the significance of gas heating and liquid charge relaxation time in the pattern formation mechanism. Time-resolved dynamics of a pulsed DC discharge indicated that the surface deformation only appeared after the establishment of plasma patterns. Statistically, the surface wave under the plasma has high wave numbers (8000–16000 m −1 ) and small amplitudes ($<$ 10 µm), generally found in the capillary wave regime. Yet the motion of surface deformations is in tandem with the plasma pattern and exhibits a nondispersive nature of constant phase velocity (0.1–0.4 m s −1 ), suggesting the dominant role of EHD force over the surface tension in the observed surface wave. These results indicate that the deformed liquid surface is driven by the EHD force of the plasma sheath. Although they share a similar geometry, the deformation and wave dynamics of the liquid surface do not stimulate a plasma pattern. Importantly, the complex EHD coupling in the plasma–liquid system raises awareness and new challenges for plasma control engineering, and the quantitative characteristics of the nondispersive surface wave are informative for advancing relevant theory and modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Thermal Response of a Lithium Vapor Divertor to Cyclical Operation

The lithium vapor divertor concept is being developed as a method to achieve detached divertor conditions in a tokamak while minimizing impurity radiation losses from the core plasma. SOLPS-ITER modeling has previously been used to identify some of the geometric constraints and required lithium evaporation rate of a lithium vapor divertor in a medium-sized tokamak during steady-state operation. Here an updated conceptual design based on these operating requirements is introduced and the thermal response of the system is modeled during cyclical operation, consistent with operation in a short-pulse tokamak. Controllability of the temperature of the lithium capillary porous system (CPS) is achieved by adopting a design where there is no line-of-sight for radiation from the plasma to reach the heated CPS surface. Operational strategies to minimize the amount of lithium evaporated between plasma discharges while achieving steady evaporation rates during plasma discharges are discussed and modeled here. The optimal feedforward control strategy demonstrated in this work is to ramp up the temperature of the evaporator as quickly as possible immediately before a plasma discharge and then reduce the heating to match the desired steady-state net evaporation rate just before the plasma discharge begins, allowing the thermal inertia of the system to stabilize the evaporation rate during the first second of the plasma discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Optimizing the Fabrication of Electrospun Nanofibrous Membrane Using Fractional Factorial Design

Electrospinning, a simple and easily tunable technique that utilizes the force balance between the electrostatic force and the solution surface tension to fabricate membranes out of 1D nanostructured fibers, has garnered much interest especially from the nanotechnology community. Depending on the morphology of the fibers, electrospun membrane has found its way in a wide range of applications, such as oil-water separation, desalination, tissue engineering, and batteries. During an electrospinning process, many factors can affect the morphology of the products, such as viscosity of the solution, voltage supply, discharge distance, feed rate of the solution, and electrospinning time. In this work, we investigated the impacts of the most important parameters on the morphology of electrospun fibrous membrane based on the fractional factorial design. We evaluated the electrospun fibrous membrane morphology using scanning electron microscopy (SEM) and capillary flow porometry. Poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) was chosen for the current study due to its interesting and versatile functionalities including superior hydrophobicity, high free volume, and piezoelectricity. This work provides valuable insight for the fabrication of electrospun membranes, especially for tailoring membrane properties in accordance with any targeted applications.

Zhao, Yajing↗