Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bulk absorbers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Identification of Recombination Losses in CdSe/CdTe Solar Cells from Spectroscopic and Microscopic Time-Resolved Photoluminescence

Due to the lowest-cost and best reliability, CdTe solar cells are the leading thin-film photovoltaic technology. Increasing open-circuit voltage by reducing recombination represents the most promising path toward further improvements. Analysis is needed to identify limitations that cause efficiency losses. To achieve this goal for Cu-doped CdSe/CdTe solar cells, time-resolved spectroscopy and microscopy are developed and applied. Recombination lifetimes and radiative efficiency identify that defect-mediated recombination is the dominant voltage loss mechanism. When carrier lifetimes are averaged over many crystalline grains, they increase from 180 to 430 ns when Al2O3 is applied to the back contact. The quasi-Fermi-level splitting correspondingly increases from 880–905 to 906–931 mV, indicating a pathway to overcome the long-standing 900 mV voltage limitation. However, the dominant recombination losses are attributed to the absorber bulk. From microscopic carrier lifetime measurements, it is identified that space charge fields due to charged grain boundaries (GBs) lead to recombination in the CdTe absorber bulk. At high injection, GB space charge fields are screened, but that occurs above 1 Sun excitation conditions. Alloying with selenium in the near-interface CdSeTe absorber region reduces GB losses and is identified as one of the factors leading to high radiative and power conversion efficiency.

14 SOLAR ENERGY↗
DOE OSTI2022

Large-Area (Ag,Cu)(In,Ga)Se 2 Thin-Film Solar Cells with Increased Bandgap and Reduced Voltage Losses Realized with Bulk Defect Reduction and Front-Grading of the Absorber Bandgap

The 1.24 eV bandgap, 18.8% power conversion efficiency Ag-alloyed chalcopyrite (Ag,Cu)(In,Ga)Se 2 (ACIGS) solar cells are characterized to relate voltage and efficiency improvements to electro-optical (EO) characteristics. Shockley-Read-Hall recombination center defect density, identified and characterized through deep level transient spectroscopy and time-resolved photoluminescence (TRPL), is reduced through potassium and copper treatment optimization. Concomitantly, longer minority carrier lifetimes are achieved, which increases open-circuit voltage (V OC ). Near-conduction band defects associated in earlier studies with light-induced current instability are also mitigated. Analysis of charge-carrier dynamics after single- and two-photon excitation is used to separate recombination at the front interface and in the absorber bulk. From TRPL decay simulations, the authors estimate ranges of key solar cell material characteristics: bulk carrier lifetime T bulk = 110-210 ns, charge-carrier mobility u = 110-160 cm 2 V -1 s -1 , and front interface recombination velocity S front = 700-1050 cm s -1 . This lowest-reported S front for ACIGS absorbers originates from the notched conduction band grading, which also makes the impact of the back interface recombination negligible. It is suggested in the results that solar cell performance enhancements can be made most readily with two distinct strategies: improving device architecture and reducing semiconductor defect densities. Using these approaches, power conversion efficiency in large-area solar cells is improved by 1.1% absolute.

14 SOLAR ENERGY↗
DOE OSTI2021

Quantifying Bulk and Surface Recombination in CdTe Solar Cells Using Time-Resolved Terahertz Spectroscopy

Understanding the nature of recombination mechanisms is essential for higher power conversion efficiency in photovoltaic (PV) devices. Here we use a combination of time-resolved terahertz spectroscopy and numerical modeling to determine the bulk Shockley-Read-Hall lifetime and interface and back surface recombination velocities in CdTe thin film stacks. Furthermore, the measurement was facilitated by fabricating wire-grid device structures using conventional laser scribing. Evaluation of a glass/FTO/SnO2/CdS/CdTe stack treated with CdCl2 allowed separation of the CdTe absorber bulk lifetime, 1.6 ns, from the back surface recombination velocity, ~6x10 4 cm/s, and indicated that CdTe/CdS interface recombination velocity had no significant impact on carrier dynamics.

14 SOLAR ENERGY↗
DOE OSTI2022

Investigating the Role of Copper in Arsenic Doped CdSeTe Photovoltaic Devices

As part of NREL's development of arsenic doped CdSeTe devices, co-doping with copper has become a common practice and, despite little difference in carrier concentration (often ~1016 cm-3), co-doped devices regularly show improved Voc. Given the critical importance of improving Voc, we are investigating this trend with a wide variety of characterization techniques including SEM, EBSD, SIMS, PL, CL, XPS, TRPL, JVT, KPFM, and DLTS. Together these indicate that Cu facilitates improved absorber-buffer interface properties and potentially improved bulk absorber characteristics, though specific mechanisms have not yet been determined. Despite the improved performance of co-doped devices, Voc is still far below its potential, and we explore the possibility that this limitation is the result of low buffer doping in conjunction with high absorber doping.

arsenic doping↗
DOE OSTI2020

Investigating the Effects of Chemical Gradients on Performance and Reliability within Perovskite Solar Cells with TOF-SIMS

Time-of-flight secondary-ion mass spectrometry (TOF-SIMS), a powerful analytical technique sensitive to all components of perovskite solar cell (PSC) materials, can differentiate between the various organic species within a PSC absorber or a complete device stack. The ability to probe chemical gradients through the depth of a device (both organic and inorganic), with down to 100 nm lateral resolution, can lead to unique insights into the relationships between chemistry in the absorber bulk, at grain boundaries, and at interfaces as well as how they relate to changes in performance and/or stability. In this essay, the technique is described; then, from the literature, several examples of how TOF-SIMS have been used to provide unique insight into PSC absorbers and devices are covered. Finally, the common artifacts that can be introduced if the data are improperly collected, as well as methods to mitigate these artifacts are discussed.

14 SOLAR ENERGY↗
DOE OSTI2023

Stability of Cu(In x Ga 1− x )Se 2 Solar Cells Utilizing RbF Postdeposition Treatment under a Sulfur Atmosphere

Alkali halide postdeposition treatments (PDTs) have become a key tool to maximize efficiency in Cu(In x Ga 1− x )Se 2 (CIGS) photovoltaics. RbF PDTs have emerged as an alternative to the more common Na‐ and K‐based techniques. This study utilizes temperature‐dependent current–voltage ( JVT ) measurements to study a unique RbF PDT performed in a S atmosphere. The samples are measured before and after 6 months in a desiccator to study device stability. Both samples contain Na and K which diffuse from the soda–lime glass substrate. A reference sample and a RbF + S PDT sample both show the development of a rear contact barrier after aging. The contact barrier is higher for the RbF + S PDT sample, leading to decreased current in forward bias. Series resistance is also higher in the RbF + S PDT device which leads to lower fill factor. However, after aging the reference sample has a larger decrease in open‐circuit voltage ( V OC ). Ideality factor measurements suggest Shockley–Read–Hall recombination dominates both samples. V OC versus temperature and a temperature‐dependent activation energy model are used to calculate diode activation energies for each sample condition. Both techniques produce similar values that indicate recombination primarily occurs within the bulk absorber.

14 SOLAR ENERGY↗
DOE OSTI2022

Investigating the Role of Copper in Arsenic Doped Cd(Se,Te) Photovoltaics

The open circuit voltage (VOC) deficit in Cd(Se,Te)-based photovoltaics remains a critical obstacle for pushing the technology closer to theoretical performance limits. Arsenic doping has become a dominant and promising route to achieve the higher p-type carrier concentrations necessary for higher VOC, but challenges associated with this alternate defect chemistry and higher doping density have hindered progress. Here we show that while arsenic doping enables high carrier concentrations (>1016 cm-3), co-doping with copper can provide a boost to VOC without a significant change to carrier concentration. A large data set is initially used to explore current-voltage and capacitance-voltage trends associated with arsenic doped devices with and without copper. A smaller subset is then used to probe these trends using a wide variety of characterization techniques. Copper is found to facilitate reduced interface recombination and potentially improved bulk absorber characteristics, though the mechanisms for these improvements are not yet clear. Despite the improved performance of co-doped devices, VOC is still far below its potential especially for highly doped devices. Low emitter doping in conjunction with high absorber doping seems to be a plausible cause for this significant deficit, though other device properties may exacerbate this problem.

CdSeTe↗
DOE OSTI2026

Gold-Induced Chemical Perturbations in CdTe-Based Photovoltaic Cells

Back-contacting p-type CdTe has been identified as one of the major areas of loss in CdTe photovoltaic (PV) power conversion efficiency (PCE). In research settings, Au is a common contact material due to its ease of use and decent performance. This work provides a detailed investigation into using gold for back contacting As-doped, CdCl 2 -treated, polycrystalline CdTe that has been exposed to air after absorber processing, another routine practice. First, X-ray photoemission spectroscopy (XPS) is used to determine the native oxide to be 1.6 nm of CdTeO 3 by using a combination of angle-resolved XPS and the cadmium-modified Auger parameter. During gold metallization of CdTe, oxygen and oxidized tellurium are eliminated from the thin CdTeO 3 native oxide. The fates of the released oxygen and possibly cadmium and tellurium are not known, but these reaction byproducts can enter the absorber bulk or grain boundaries, stay at the interface, or dissolve in the Au. Interfacial hole barriers between CdTe and Au are measured for samples with and without the native oxide present prior to metallization. Results show that the thin CdTeO 3 alleviates the downward band bending by 40 meV from 470 to 430 meV even though it is consumed during interface formation. The implications of these chemical reactions on the device are assessed through photoluminescence (PL) spectroscopy, which shows losses in internal open circuit voltage (iVoc) from 820 to 795 meV, carrier lifetime from 123 to 45 ns, and PL quantum yield from 2.9 × 10 −5 to 1.2 × 10 −5 . Modeling timeresolved PL lifetimes demonstrates the back surface recombination velocity due to metallization reduces minority carrier lifetimes. These results identify the native oxide and show that it plays an important role in mediating downward band bending along with how the back interface reaction can negatively impact device-scale parameters and reduce PV PCE.

14 SOLAR ENERGY↗
DOE OSTI2021

Diverse simulations of time-resolved photoluminescence in thin-film solar cells: A SnO 2 /CdSe y Te 1-y case study

Time-resolved photoluminescence (TRPL) is widely used to measure carrier lifetime in thin-film solar cell absorbers. However, the injection dependence of data and frequent non-exponential decay shapes complicate the interpretation. Here, we develop a numerical model to simulate injection-dependent TRPL measurements in a SnO 2 /CdSe y Te 1-y case study solar cell structure, considering parameters of interest to researchers in industry and academia. Previous simulations have shown that, in low injection, excess electrons and holes injected by the laser pulse are rapidly separated in the electric field formed by the pn junction. As a result, at early times, the PL signal can decay faster than the Shockley-Read-Hall lifetime in the absorber bulk (t_bulk). Prior simulations have shown that the charge stored in the junction can slowly leak out to affect decays at late times. However, it has not been clear if and to what degree charge storage can affect the slopes extracted from TRPL decays - t_2 - commonly cited as the TRPL-measured lifetime. Here, we show that charge storage can, in some cases, result in t_2 values that substantially overestimate t_bulk. Previous simulations indicate that high injection conditions can screen the junction field and minimize charge separation. Here, we show that continued injection increases can drive down t_2 below t_bulk as radiative recombination becomes dominant. We catalog charge storage and radiative recombination impacts for a diverse set of material parameters and compare results to double-heterostructure models.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS,S↗
DOE OSTI2021

Voltage Loss Comparison in CdSe/CdTe Solar Cells and Polycrystalline CdSeTe Heterostructures

Cd(Se)Te solar cells have considerable headroom to increase voltage. Voltage losses occur due to incomplete absorption above bandgap E_g and band tail absorption below E_g; such losses are quantified using radiative voltage. The largest voltage losses are attributed to nonradiative recombination, which is quantified via carrier lifetime and radiative efficiency. We compare radiative voltage, radiative efficiency, and carrier lifetime for Cu-doped CdSe/CdTe solar cells and for undoped polycrystalline CdSeTe heterostructures passivated with Al_2O_3. Using external quantum efficiency spectrum and a CdSeTe absorption spectrum obtained from absolute photoluminescence (PL), we show that the radiative voltage is greater than 1.1 V. Time-resolved PL experiments and modeling show that a major part of voltage losses can be attributed to recombination in the absorber bulk. The front interface recombination makes a larger impact within the first few nanoseconds after pulsed excitation, and the comparison of time-gated and time-integrated PL can be used to assess relative contributions of front interface and bulk recombination rates.

14 SOLAR ENERGY↗
DOE OSTI2026

Data for "Gold-Induced Chemical Perturbations in CdTe-Based Photovoltaic Cells"

Back contacting p-type CdTe has been identified as one of the major areas of loss in CdTe photovoltaic (PV) power conversion efficiency (PCE). In research settings, Au is a common contact material due to its ease of use and decent performance. This work provides a detailed investigation into using gold for back contacting As-doped, CdCl2 treated, polycrystalline CdTe that has been exposed to air after absorber processing, another routine practice. First, X-ray photoemission spectroscopy (XPS) is used to determine the native oxide to be 1.6 nm of CdTeO3 using a combination of angle-resolved XPS and the cadmium modified Auger parameter. During gold metallization of CdTe, oxygen and oxidized tellurium are eliminated from the thin CdTeO3 native oxide. The fate of the released oxygen and possibly cadmium and tellurium are not known, but these reaction byproducts can enter the absorber bulk or grain boundaries, stay at the interface, or dissolve in the Au. Interfacial hole barriers between CdTe and Au are measured for samples with and without the native oxide present prior to metallization. Results show that the thin CdTeO3 alleviates the downward band bending by 40 meV from 470 meV to 430 meV even though it is consumed during interface formation. The implications of these chemical reactions on the device are assessed through photoluminescence (PL) spectroscopy which shows losses in internal open circuit voltage (iVoc) from 820 meV to 795 meV, carrier lifetime from 123 ns to 45 ns, and PL quantum yield from 2.9x10-5 to 1.2x10-5. Modeling time-resolved PL lifetimes demonstrates the back surface recombination velocity due to metallization reduces minority carrier lifetimes. These results identify the native oxide and show that it plays an important role in mediating downward band bending along with how the back interface reaction can negatively impact device-scale parameters and reduce PV PCE.

14 SOLAR ENERGY↗
DOE OSTI2025

X-Ray and Electron Spectroscopy of the CdS/(Ag,Cu)(In,Ga)Se 2 Interface With RbF Treatment

The chemical and electronic structure of the CdS/(Ag,Cu)(In,Ga)Se 2 (CdS/ACIGSe) interface for thin-film solar cells, involving an absorber with a bulk [Ag]/([Ag]+[Cu]) (AAC) ratio of 0.06, a state-of-the-art RbF post-deposition treatment (PDT), and a chemical-bath deposited CdS buffer layer, is studied. To gain a detailed and depth-resolved picture of the CdS/ACIGSe interface, synchrotron- and laboratory-based hard X-ray, soft X-ray, and UV photoelectron spectroscopy, inverse photoemission spectroscopy, and X-ray emission spectroscopy are combined. Compared to the bulk of the absorber, a Cu- and Ga-poor ACIGSe surface is found, with a slightly increased AAC ratio. Strong evidence of a Rb–In–Se species (possibly with some Ag) at the absorber surface is compiled, with a corresponding band gap of 2.79 ± 0.12 eV. This finding is in clear contrast to comparable Ag-free Cu(In,Ga)Se 2 absorbers with RbF-PDT. The Rb–In–Se surface species is not removed by the (wet-chemical) CdS deposition process, while some Se diffuses into the CdS layer and segregates at its surface. The CdS buffer layer shows a band gap of 2.48 ± 0.12 eV, and a cliff (≈ -0.4 eV) is determined in the conduction band alignment at the interface between the Rb–In–Se species and the CdS buffer.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Incorporating Electrochemical Halide Oxidation into Drift-Diffusion Models to Explain Performance Losses in Perovskite Solar Cells under Prolonged Reverse Bias

Partial shading of a solar module can induce a set of cells within the module to operate under reverse bias. Studies have shown that metal halide perovskite solar cells with a wide variety of compositions and contacts exhibit interesting behavior in reverse bias that includes both reversible performance loss and non-reversible degradation. In this paper, an advanced drift-diffusion approach incorporating an electrochemical term to explain the short-circuit, open circuit and fill factor losses that are experimentally measured after prolonged reverse bias is used. It is shown that holes can tunnel into the perovskite due to sharp band bending near the contact, accumulate within the bulk of the perovskite absorber, and trigger the oxidation of halides to form neutral halogens. The density of neutral halogens is much higher in reverse bias because there are hardly any electrons available to reduce the iodine. The resulting halogens act as bulk recombination centers. While the interstitial halogen density does decay when the cell is operated in forward bias, permanent degradation can occur if the iodine diffuses out of the perovskite layer. Finally, the ways in which changing parameters such as the mobile ion density or the series resistance at the contact can influence device performance and stability are discussed.

degradation↗
DOE OSTI2020

Surface-Activated Corrosion in Tin–Lead Halide Perovskite Solar Cells

Mixed tin–lead halide perovskite solar cells have promising power conversion efficiencies, but long-term stability is still a challenge. Here, we examine the stability of a 60:40 tin–lead perovskite to better understand diminished device performance upon thermal treatment, both in ambient and inert atmosphere. Operando X-ray diffraction shows a stable bulk structure of the perovskite absorber, leading to the hypothesis that surface chemistry dominates the degradation mechanism. X-ray photoelectron spectroscopy reveals two new observations post-thermal annealing that accompany previously reported Sn 4+ evolution: (i) the formation of I 3 – intermediates preceding I 2 loss at the surface and (ii) evidence of under-coordinated tin and lead surface sites (Sn δ<2+ and Pb δ<2+ , respectively) in inert and ambient conditions. These two species indicate an activated corrosion (i.e., both oxidation and reduction) process at the surface as a possible chemical pathway for degradation, which is expected to be accelerated under operando voltage and light biases.

14 SOLAR ENERGY↗
DOE OSTI2023

Synergetic Effect of Aluminum Oxide and Organic Halide Salts on Two‐Dimensional Perovskite Layer Formation and Stability Enhancement of Perovskite Solar Cells

Long-chain organic halide salts are widely used in perovskite-based optoelectronic devices for surface passivation owing to their capability to interact with the surface defects of perovskites. Here, aluminum oxide (AlO x ) is introduced via atomic layer deposition onto octylammonium iodide (OAI) to exploit the benefits of organic halide salts without generating undesired defects. The devices incorporating AlO x on OAI-treated perovskite (OAI/AlO x ) show enhancement in both device performance and photo-stability compared to those with only treatment. A diffusion of aluminum from AlO x into the perovskite through surface characterization contributes to a uniform photo-generated carrier transport in both the surface and the bulk of the perovskite absorber. In addition, it is revealed that light-induced two-dimensional perovskite formation on OAI/AlO x . This may be ascribed to preventing the loss of OA cations due to the presence of AlO x , leading to a decrease in the number of iodine anions which suppresses the light-induced degradation of corresponding devices. Consequently, the devices show over 24% efficiency and retain their efficiency over 1000 hours under continuous light illumination.

14 SOLAR ENERGY↗
DOE OSTI2020

Ultra-thin passivation layers in Cu(In,Ga)Se 2 thin-film solar cells: full-area passivated front contacts and their impact on bulk doping

In the search for highly transparent and non-toxic alternative front layers replacing state-of-the-art CdS in Cu(In,Ga)Se 2 thin-film solar cells, alternatives rarely exceed reference devices in terms of efficiency. Full-area ultra-thin aluminium oxide tunnelling layers do not require any contact patterning and thus overcome the main drawback of insulating passivation layers. Even a few monolayers of aluminium oxide can be deposited in a controlled manner by atomic layer deposition, they show excellent interface passivation properties, low absorption, and suitable current transport characteristics on test devices. Depositing a ZnO-based transparent front contact, however, results in extremely poor solar cell performance. The issue is not necessarily a low quality of the alternative front layer, but rather the intricate relation between front layer processing and electronic bulk properties in the absorber layer. We identify three challenges critical for the development of novel front passivation approaches:(i) both Cd and Zn impurities beneficially reduce the high native net dopant concentration in the space charge region, (ii) sputter deposition of ZnO damages the passivation layer resulting in increased interface recombination, (iii) thermal treatments of devices with ZnO layer result in substantial Zn diffusion, which can penetrate the full absorber thickness already at moderate temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Subsurface hydrogen, curvature, and strain: lessons from electro-reduction of benzaldehyde on nano-structured Pd catalysts

The unique ability of palladium (Pd) to absorb hydrogen and form a bulk hydride is vital for chemical transformations that involve hydrogenation reactions. Nano-structured Pd catalysts offer a promise of tuning these reaction rates by exploiting variations of reactant binding energies depending on the surface structure and morphological constraints that result in inhomogeneous strain. However, the interplay between the nano-structure of Pd and the ability of Pd to adsorb (and absorb) hydrogen as well as other reactive species needs to be better understood for a rational understanding of competitive chemical transformations at Pd surfaces. We consider the effects of the surface corrugation, strain, and subsurface Pd hydride on the reduction of benzaldehyde to benzyl alcohol in two qualitatively different samples – Pd nanoparticles and Pd gels formed by quasi-one-dimensional chains of these nanoparticles. Our electrochemical measurements and computational modelling suggest that surface concave sites, inherent to Pd gels, facilitate hydrogen transfer to the Pd subsurface region, thus weakening benzaldehyde binding to the surface. This effect is further modulated by the strain, depending on the local coordination environment on the corrugated surface. Furthermore, these findings demonstrate how structurally complex samples in the form of gels provide degrees of freedom for controlling the behavior of metal catalysts that are not available in isolated nanoparticles, which paves the way for new approaches in the design of catalytic materials and synthesis of metal hydrides.

Padavala, Sri Krishna Murthy [University of Minnes↗
DOE OSTI2023

Stretchable Photodiodes with Polymer-Engineered Semiconductor Nanowires for Wearable Photoplethysmography

Healthcare systems worldwide have been stressed to provide sufficient resources to serve the increasing and aging population in our society. The situation became more challenging at the time of pandemic. Technology advancement, especially the adoption of wearable health monitoring devices, has provided an important supplement to current clinical equipment. Most health monitoring devices are rigid, however, human tissues are soft. Such a difference has prohibited intimate contact between the two and jeopardized wearing comfortableness, which hurdles measurement accuracy especially during longtime usage. Here, in this work, we report a soft and stretchable photodiode that can conformally adhere onto the human body without any pressure and measure cardiovascular variables for an extended period with higher reliability than commercial devices. The photodiode used a composite light absorber consisting of an organic bulk heterojunction embedded into an elastic polymer matrix. It is discovered that the elastic polymer matrix not only improves the morphology of the bulk heterojunction for obtaining the desired mechanical properties but also alters its electronic band structure and improves the electrical properties that lead to a reduced dark current and enhanced photovoltage in the stretchable photodiode. The work has demonstrated high fidelity measurements and longtime monitoring of heat rate variability and oxygen saturation, potentially enabling next-generation wearable photoplethysmography devices for point-of-care diagnosis of cardiovascular diseases in a more accessible and affordable way.

77 NANOSCIENCE AND NANOTECHNOLOGY↗