Interference and radiation blockage effects on surface temperatures of composite flight vehicles
Interference effects on aerodynamic heating and radiation blockage effects on surface temperature of space shuttle during boost
Thomas, A. C.↗
SEARCH · Engineering Papers
Results for “blockage effect”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Swirl, Expansion Ratio and Blockage Effects on Confined Turbulent Flow
A confined jet test facility, a swirles, flow visualization equipment, five-hole pitot probe instrumentation; flow visualization; and effects of swirl on open-ended flows, of gradual expansion on open-ended flows, and blockages of flows are addressed.
Scharrer, G. L.↗
Blockage effects of cone-cylinder bodies on perforated wind tunnel wall interference
Cone-cylinder models tested in supersonic wind tunnel to evaluate effect of wall reflected disturbances on model pressure distributions
Mitchell, G. A.↗
Effect of blockage ratio on drag and pressure distributions for bodies of revolution at transonic speeds
Experimental data were obtained in two wind tunnels for 13 models over a Mach number range from 0.70 to 1.02. Effects of increasing test-section blockage ratio in the transonic region near a Mach number of 1.0 included change in the shape of the drag curves, premature drag creep, delayed drag divergence, and a positive increment of pressures on the model afterbodies. Effects of wall interference were apparent in the data even for a change in blockage ratio from a very low 0.000343 to an even lower 0.000170. Therefore, models having values of blockage ratio of 0.0003 - an order of magnitude below the previously considered safe value of 0.0050 - had significant errors in the drag-coefficient values obtained at speeds near a Mach number of 1.0. Furthermore, the flow relief afforded by slots or perforations in test-section walls - designed according to previously accepted criteria for interference-free subsonic flow - does not appear to be sufficient to avoid significant interference of the walls with the model flow field for Mach numbers very close to 1.0.
Couch, L. M.↗
Airloads on bluff bodies, with application to the rotor-induced downloads on tilt-rotor aircraft
The aerodynamic characteristics of airfoils with several flap configurations were studied theoretically and experimentally in environments that simulate a wing immersed in the downwash of a hovering rotor. Special techniques were developed for correcting and validating the wind tunnel data for large blockage effects, and the test results were used to evaluate two modern blockage effects, and the test results were used to evaluate two modern computational aerodynamics codes. The combined computed and measured results show that improved flap and leading-edge configurations can be designed which will achieve large reductions in the downloads of tilt-rotor aircraft, and thereby improve their hover efficiency.
Mccroskey, W. J.↗
Airloads on bluff bodies, with application to the rotor-induced downloads on tilt-rotor aircraft
The aerodynamic characteristics of airfoils with several flap configurations were studied theoretically and experimentally in environments that simulate a wing immersed in the downwash of a hovering rotor. Special techniques were developed for correcting and validating the wind tunnel data for large blockage effects, and the test results were used to evaluate two modern blockage effects, and the test results were used to evaluate two modern computational aerodynamics codes. The combined computed and measured results show that improved flap and leading-edge configurations can be designed which will achieve large reductions in the downloads of tilt-rotor aircraft, and thereby improve their hover efficiency.
Mccroskey, W. J.↗
Diffraction studies applicable to 60-foot microwave research facilities
The principal features of this document are the analysis of a large dual-reflector antenna system by vector Kirchhoff theory, the evaluation of subreflector aperture-blocking, determination of the diffraction and blockage effects of a subreflector mounting structure, and an estimate of strut-blockage effects. Most of the computations are for a frequency of 15.3 GHz, and were carried out using the IBM 360/91 and 360/95 systems at Goddard Space Flight Center. The FORTRAN 4 computer program used to perform the computations is of a general and modular type so that various system parameters such as frequency, eccentricity, diameter, focal-length, etc. can be varied at will. The parameters of the 60-foot NRL Ku-band installation at Waldorf, Maryland, were entered into the program for purposes of this report. Similar calculations could be performed for the NELC installation at La Posta, California, the NASA Wallops Station facility in Virginia, and other antenna systems, by a simple change in IBM control cards. A comparison is made between secondary radiation patterns of the NRL antenna measured by DOD Satellite and those obtained by analytical/numerical methods at a frequency of 7.3 GHz.
Schmidt, R. F.↗
Partition Thickness Considerations for Additively Manufactured Acoustic Liners
Three types of uniform-depth liners are evaluated to explore the effects of partition thickness on the surface impedance achieved with additively manufactured liners. A transmission line code is used to predict the effects of sound transmission through empty chambers and wire mesh facesheets, and is combined with the Motsinger and Kraft model to account for sound transmission through perforated facesheets. The inclusion of partitions causes a blockage effect, i.e., a portion of the surface is ‘blocked’ (nonactive surface). For liners with no facesheet, these blockage effects are incorporated simply by accounting for the change in cross sectional area between the individual chamber and the unit cell that includes half of a partition thickness around the perimeter of this chamber. Comparison of impedances predicted in this manner with data acquired in the NASA Langley Normal Incidence Tube (NIT) confirms the efficacy of this modeling approach. Two approaches are considered to account for the inclusion of a wiremesh or perforated plate facesheet on these same cores. The first accounts for the effects of partition thickness before including the transfer impedance across the facesheet, while the second reverses these steps. A comparison of data acquired in the NASA NIT with modeled impedances suggests the first approach is best when the facesheet is a wire mesh, but the second approach is preferred when a perforated plate facesheet is used. It is hypothesized that this is due to the fact that a lumped element model is used to compute the transfer impedance across a wire mesh, while the corresponding transfer impedance across a perforated sheet explicitly incorporates the efffects of the liner core. However, comparisons of data acquired in the NASA Langley Grazing Flow Impedance Tube with modeled impedances seem slightly better when the first approach is employed with a perforated plate facesheet. Thus, the effects of partition thickness on liners with perforated sheets subjected to grazing incidence sound require further review
acoustic↗
Radial and circumferential flow surveys at the inlet and exit of the Space Shuttle Main Engine High Pressure Fuel Turbine Model
The main objective of this test was to obtain detailed radial and circumferential flow surveys at the inlet and exit of the SSME High Pressure Fuel Turbine model using three-hole cobra probes, hot-film probes, and a laser velocimeter. The test was designed to meet several objectives. First, the techniques for making laser velocimeter, hot-film probe, and cobra probe measurements in turbine flows were developed and demonstrated. The ability to use the cobra probes to obtain static pressure and, therefore, velocity had to be verified; insertion techniques had to be established for the fragile hot-film probes; and a seeding method had to be established for the laser velocimetry. Once the measurement techniques were established, turbine inlet and exit velocity profiles, temperature profiles, pressure profiles, turbulence intensities, and boundary layer thicknesses were measured at the turbine design point. The blockage effect due to the model inlet and exit total pressure and total temperature rakes on the turbine performance was also studied. A small range of off-design points were run to obtain the profiles and to verify the rake blockage effects off-design. Finally, a range of different Reynolds numbers were run to study the effect of Reynolds number on the various measurements.
Hudson, S. T.↗
Effects of antenna blockage on radio frequency performance of the microwave radiometer spacecraft
Radio frequency scaled models of the microwave radiometer spacecraft suspended feed concept were tested to determine the effects of aperture blockage on the antenna radiation pattern. Contributors to the uncertainty of the test measurements were evaluated, and an estimate of the blockage effects was made for comparison with the test measurements. The gain loss budget associated with reflector performance characteristics (aperture blockage, surface reflectivity, reflector roughness, and defocus) was determined.
Sikes, L. D.↗
Simulating Ice Accretion Effects on Engine Performance
Develop a modeling tool that can be used to predict the onset of engine icing due to ice crystal ingestion. The tool will be capable of modeling the effects of ice build up as well as its effect on engine performance. Perform a parametric study of an engine with simulated ice blockage effects at altitude conditions. Using the tool, estimate the effect of blockage in the low pressure compressor due to ice buildup (accretion), and its effects on engine performance.
Jorgenson, Philip C. E.↗
Support System Effects on the DLR-F6 Transport Configuration in the National Transonic Facility
An experimental investigation of the DLR-F6 generic transport configuration was conducted in the NASA NTF for use in the Drag Prediction Workshop. As data from this experimental investigation was collected, a large difference in drag values was seen between the NTF test and an ONERA test that was conducted several years ago. After much investigation, it was determined that this difference was likely due to a sting effect correction applied to the ONERA data which NTF does not use. This insight led to the present work. In this study, a computational assessment has been undertaken to investigate model support system interference effects on the DLR-F6 transport configuration. The configurations computed during this investigation were the isolated wing-body, the wing-body with the full support system (blade and sting), the wing-body with just the blade, and the wing-body with just the sting. The results from this investigation show the same trends that ONERA saw when they conducted a similar experimental investigation in the S2MA tunnel. Computational results suggest that the blade contributed an interference type of effect, the sting contributed a general blockage effect, and the full support system combined these effects.
Rivers, Melissa B.↗
On Blockage Corrections for Two-dimensional Wind Tunnel Tests Using the Wall-pressure Signature Method
The Wall-Pressure Signature Method for correcting low-speed wind tunnel data to free-air conditions has been revised and improved for two-dimensional tests of bluff bodies. The method uses experimentally measured tunnel wall pressures to approximately reconstruct the flow field about the body with potential sources and sinks. With the use of these sources and sinks, the measured drag and tunnel dynamic pressure are corrected for blockage effects. Good agreement is obtained with simpler methods for cases in which the blockage corrections were about 10% of the nominal drag values.
Allmaras, S. R.↗
Radio frequency performance predictions for the hoop/column point design
Preliminary antenna pattern tests were conducted to determine if catastrophic effects were produced by cables (conducting) in the aperture. This test consisted of an apex feed illuminating a 3 meter solid reflector. A hoop/column configuration was used in positioning the various wires and cables. Radiation patterns were measured at 7 GHz and 10 GHz. No catastrophic effects were observed for this configuration, but additional tests are required to determine the effects for more precision multiple beam applications. In order to better understand the scattering and blockage effects on multiple beam performance, a 35 GHz model was used to model somewhat a single quad aperture configuration. Experimental results using this models are presented in graphs.
Campbell, T. G.↗
A method for the modelling of porous and solid wind tunnel walls in computational fluid dynamics codes
Porous wall wind tunnels have been used for several decades and have proven effective in reducing wall interference effects in both low speed and transonic testing. They allow for testing through Mach 1, reduce blockage effects and reduce shock wave reflections in the test section. Their usefulness in developing computational fluid dynamics (CFD) codes has been limited, however, by the difficulties associated with modelling the effect of a porous wall in CFD codes. Previous approaches to modelling porous wall effects have depended either upon a simplified linear boundary condition, which has proven inadequate, or upon detailed measurements of the normal velocity near the wall, which require extensive wind tunnel time. The current work was initiated in an effort to find a simple, accurate method of modelling a porous wall boundary condition in CFD codes. The development of such a method would allow data from porous wall wind tunnels to be used more readily in validating CFD codes. This would be beneficial when transonic validations are desired, or when large models are used to achieve high Reynolds numbers in testing. A computational and experimental study was undertaken to investigate a new method of modelling solid and porous wall boundary conditions in CFD codes. The method utilized experimental measurements at the walls to develop a flow field solution based on the method of singularities. This flow field solution was then imposed as a pressure boundary condition in a CFD simulation of the internal flow field. The effectiveness of this method in describing the effect of porosity changes on the wall was investigated. Also, the effectiveness of this method when only sparse experimental measurements were available has been investigated. The current work demonstrated this approach for low speed flows and compared the results with experimental data obtained from a heavily instrumented variable porosity test section. The approach developed was simple, computationally inexpensive, and did not require extensive or intrusive measurements of the boundary conditions during the wind tunnel test. It may be applied to both solid and porous wall wind tunnel tests.
Beutner, Thomas John↗
Steady-state performance of J85-21 compressor at 100 percent of design speed with and without interstage rake blockage
Internal compressor instrumentation blockage effects on steady state J85-21 compressor performance at 100 percent of design speed are determined. The blockage was generated by instrumented vanes for the first three compressor stages and by removal rakes for stages 4 to 9. Individual flow passage blockages ranged up to 4.5 percent with the instrumented vanes and up to 22 percent with the removable interstage rakes. At a Reynolds number index of 1.0, pressure ratio and airflow remained unchanged with insertion of the interstage rakes, but efficiency dropped 0.3 percentage point. Compressor exit profiles, compressor stage static pressure rise coefficients, turbine exit temperature, and fuel flow are also presented.
Werner, R. A.↗
CFD Analysis of an Installation Used to Measure the Skin-Friction Penalty of Acoustic Treatments
There is a drive to devise acoustic treatments with reduced skin-friction and therefore fuel-burn penalty for engine nacelles on commercial airplanes. The studies have been experimental, and the effects on skin-friction are deduced from measurements of the pressure drop along a duct. We conduct a detailed CFD analysis of the installation, for two purposes. The first is to predict the effects of the finite size of the rig, including its near-square cross-section and the moderate length of the treated patch; this introduces transient and blockage effects, which have not been included so far in the analysis. In addition, the flow is compressible, so that even with homogeneous surface conditions, it is not homogeneous in the streamwise direction. The second purpose is to extract an effective sand-grain roughness size for a particular liner, which in turn can be used in a CFD analysis of the aircraft, leading to actual predictions of the effect of acoustic treatments on fuel burn in service. The study is entirely based on classical turbulence models, with an appropriate modification for effective roughness effects, rather than directly modeling the liners.
Spalart, Philippe R.↗
An experimental study of wall adaptation and interference assessment using Cauchy integral formula
This paper summarizes the results of an experimental study of combined wall adaptation and residual interference assessment using the Cauchy integral formula. The experiments were conducted on a supercritical airfoil model in the Langley 0.3-m Transonic Cryogenic Tunnel solid flexible wall test section. The ratio of model chord to test section height was about 0.7. The method worked satisfactorily in reducing the blockage interference and demonstrated the primary requirement for correcting for the blockage effects at high model incidences to correctly determine high lift characteristics. The studies show that the method has potential for reducing the residual interference to considerably low levels. However, corrections to blockage and upwash velocities gradients may still be required for the final adapted wall shapes.
Murthy, A. V.↗