SEARCH · Engineering Papers

Results for “biot number analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

12 records

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Thermal Modeling and Limitations for Power Electronics Embedded in Medium-Voltage Cables

As next-generation energy technologies gain traction and power demand increases, the existing electrical infrastructure faces significant stress, prompting innovative solutions to enhance the grid's capacity and lifespan. This work explores the possibility of embedding medium-voltage (MV) power electronics directly inline with the cable, and the resulting thermal challenges. Since the majority of power distribution cables installed in the U.S. are passively cooled, the work focuses primarily on passive cooling, with an emphasis on the limitations of axial heat spreading within the cable. To date, literature on axial spreading of high incident heat loads on cables and cable environments is limited, typically reporting cases with <10 W of incident heat load. This work will explore the considerations, limits, and tradeoffs of cable-embedded heat loads significantly larger than the cable losses. Both external and internal effects are modeled analytically in nondimensional terms via a Biot number analysis, allowing fundamental limits and tradeoffs to be derived. The work culminates in the design and experimental validation of a cable-embedded thermal system capable of passively dissipating 300 W of heat from a coaxial SiC mosfet switch module over a length of 20 cm, thus validating the possibility of MV cable-embedded power electronics from a thermal standpoint.

24 POWER TRANSMISSION AND DISTRIBUTION↗

NASA NTRS1982

An analytical approach to thermal modeling of Bridgman-type crystal growth. I - One-dimensional analysis

A relatively simple one-dimensional thermal model of the Bridgman growth process has been developed which is applicable to the growth of small diameter samples with conductivities similar to those of metallic alloys. The heat flow in a translating rod is analyzed in a way that is applicable to Biot numbers less than unity. The model accommodates an adiabatic zone, different heat transfer coefficients in the hot and cold zones, and changes in sample material properties associated with phase change. The analysis is applied to several simplified cases. The effect of the rod's motion is studied in a three-zone furnace for a rod sufficiently long that end effects can be neglected; end effects are then investigated for a motionless rod. Finally, the addition of a fourth zone, an independently controlled booster heater between the main heater and the adiabatic zone, is evaluated for its ability to increase the gradient in the sample at the melt interface and to control the position of the interface.

Naumann, R. J.↗

DOE OSTI2023

Interpreting T-History Data on Supercooling and Phase Change Enthalpy of a Salt-Hydrogel Complex for Building Thermal Management

Phase change materials (PCMs) are promising materials for storing and discharging latent heat in buildings to regulate the thermal environment. Measurement of salt hydrate PCM thermal performance is often challenging because of supercooling and phase segregation. Though differential scanning calorimetry (DSC) has been widely used to measure thermal properties of various phase change materials, DSC uses milligrams of sample and is unrealistic for predicting large-scale materials performance. The T-history method [1], in contrast, handles higher volumes but the analysis typically requires a lumped capacitance assumption. Here, we report and analyze T-History data on a novel salt-hydrogel complex with high viscosity, that renders low Biot number sample preparation extremely challenging. We re-examine the standard T-history method and compared against DSC data in this complex material. We report details of an experimental setup, built with necessary additions to a controlled environmental chamber. We carefully examine the validity of the lumped capacitance assumption and suggest a modified analysis using a computational approach for reliable data. Experimental parameters such as ramp rate and temperature range of the environmental chamber are considered via computational modeling to understand the effect of ramp rate on supercooling [2]. Finally, we report thermal cycling experiments on the salt-hydrogel complex. Our modified approach to measuring supercooling and enthalpy of fusion at large scales is important in better understanding the performance of phase-change materials at scale for building thermal storage. References: [1] Marin, Jose M, Belen Zalba, Luisa F Cabeza, and Harald Mehling. “Determination of Enthalpy Temperature Curves of Phase Change Materials with the Temperature-History Method: Improvement to Temperature Dependent Properties.” Measurement Science and Technology 14, no. 2 (February 1, 2003): 184–89. https://doi.org/10.1088/0957-0233/14/2/305. [2] Safari, A., R. Saidur, F.A. Sulaiman, Yan Xu, and Joe Dong. “A Review on Supercooling of Phase Change Materials in Thermal Energy Storage Systems.” Renewable and Sustainable Energy Reviews 70 (April 2017): 905–19. https://doi.org/10.1016/j.rser.2016.11.272

thermodynamics↗

DOE OSTI2021

Simulations of biomass pyrolysis using glued-sphere CFD-DEM with 3-D intra-particle models

The shape of biomass particles influences intra-particle heat transfer, particle-particle collisions, interphase momentum, heat transfer, and pyrolysis yield. In this research, the effects of these multi-scale phenomena are captured using a glued-sphere computational fluid dynamic discrete element method (CFD-DEM) with 3-D intra-particle models. The glued-spheres resolved the shapes of particles and intra-particle temperature and species distributions. The implementation was validated using the pyrolysis data of a spherical particle and a cylindrical particle. Then, the influences of biomass shapes and sizes on pyrolysis were investigated. The results revealed the significant influence of surface areas and mass distributions on interphase heat transfer and chemical reactions. The intra-particle heat transfer is neglectable for a Biot number smaller than 0.41. Finally, the pyrolysis of irregularly shaped biomass particles in a fixed bed, fluidized bed, and spouted bed was simulated. Analysis of conversion distributions showed the largest deviations in the fixed bed and the slowest conversion rate in the spouted bed. A good balance between uniform and fast conversion is achieved in the fluidized bed. The multi-scale method proposed in this research provides a tool for the evaluation of large irregular-shaped biomass particle pyrolysis in different types of reactors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Thermal conductivity of two-dimensional disordered fibrous materials defined by interfiber thermal contact conductance and intrinsic conductivity of fibers

A general framework for the theoretical analysis and numerical calculations of the effective thermal conductivity of two-dimensional homogeneous and isotropic disordered fibrous materials is developed in this work based on the model of random contacts between soft-core spherocylinders. The analysis accounts for the interfiber contact conductance and intrinsic conductivity of fibers and is performed in a wide space of governing parameters that includes the fiber aspect ratio, Biot number calculated for a single thermal contact between fibers, and material density ranging from values corresponding to the percolation threshold up to those characteristic of dense fiber networks. For dense networks, exact theoretical equations for the thermal conductivity of materials composed of spherocylinders with an arbitrary aspect ratio and Biot number are derived. The effect of the intrinsic conductivity of fibers on the thermal transport in fibrous materials is found to depend on the density of contacts and can be significant in sufficiently dense fiber networks even if the Biot number for a single thermal contact is small. Semiempirical corrections to the theoretical equations are derived for small and moderate fiber densities. The power law exponent describing the approximate dependence of the conductivity on the density parameter is found to vary from values close to 1 up to values exceeding 2 when evaluated within different finite ranges of the density parameter. This finding explains the variability of scaling laws for thermal conductivity of fibrous materials suggested in the literature based on numerical simulations performed in different regions of the space of material parameters.

36 MATERIALS SCIENCE↗

NASA NTRS1973

Analysis of transient heat flow to thick-walled plates and cylinders

A methodology is described for the analysis of a transient temperature measurement made in a flat or curved plate subjected to convective heat transfer, such that the surface heat flux, the hot-gas temperture, and the gas heat transfer coefficient can be determined. It is shown that if the transient temperature measurement is made at a particular point located nearly midway in the thickness of the plate there is an important simplification in the data analysis process, in that the factor relating the surface heat flux to the measured rate of rise of temperature becomes invariant for a Fourier Number above 0.60 and for all values of the Biot Number. Parameters are derived, tabulated, and plotted which enable straightforward determination of the surface heat flux, the hot-gas temperature, of the plate, the rate of rise of temperature, the plate thickness and curvature, and the mean thermal properties of the plate material at the test temperature.

Powell, W. B.↗

NASA NTRS1991

Effects of anisotropic conduction and heat pipe interaction on minimum mass space radiators

Equations are formulated for the two dimensional, anisotropic conduction of heat in space radiator fins. The transverse temperature field was obtained by the integral method, and the axial field by numerical integration. A shape factor, defined for the axial boundary condition, simplifies the analysis and renders the results applicable to general heat pipe/conduction fin interface designs. The thermal results are summarized in terms of the fin efficiency, a radiation/axial conductance number, and a transverse conductance surface Biot number. These relations, together with those for mass distribution between fins and heat pipes, were used in predicting the minimum radiator mass for fixed thermal properties and fin efficiency. This mass is found to decrease monotonically with increasing fin conductivity. Sensitivities of the minimum mass designs to the problem parameters are determined.

Baker, Karl W.↗

DOE OSTI2026

Flash Heating of a Hollow Rod to Determine Thermal Properties

In a nuclear reactor, prolonged exposure to high neutron flux levels can change material properties of reactor components. Due to the danger posed to personnel by highly radioactive components such as spent fuel, noncontact methods must be used to determine these properties. The objective of the current research is to test the viability of using a flash-heating method to determine the thermal diffusivity of a silicon carbide (SiC) tube, which could be used as cladding for a nuclear fuel rod. The flash-heating experiment was conducted at Oak Ridge National Laboratory and temperature results were analyzed as a two-Dimensional cross section which assumed axial symmetry. The model was fitted iteratively to the temperature measurements using nonlinear regression which required values for thermal diffusivity, Biot number and a term to determine the magnitude of the heat absorbed by the flash. The method could be expanded in the future to estimate the thermal diffusivity of spent nuclear fuel rods in an effort to increase the certainty of new reactor designs using precise thermal properties throughout the core life. A statistical analysis of the results of this work is provided as part of the analysis.

McMasters, Robert L [Virginia Military Institute, ↗

NASA NTRS2001

Crystal Growth and Fluid Mechanics Problems in Directional Solidification

Our work in directional solidification has been in the following areas: (1) Dynamics of dendrites including rigorous mathematical analysis of the resulting equations; (2) Examination of the near-structurally unstable features of the mathematically related Hele-Shaw dynamics; (3) Numerical studies of steady temperature distribution in a vertical Bridgman device; (4) Numerical study of transient effects in a vertical Bridgman device; (5) Asymptotic treatment of quasi-steady operation of a vertical Bridgman furnace for large Rayleigh numbers and small Biot number in 3D; and (6) Understanding of Mullins-Sererka transition in a Bridgman device with fluid dynamics is accounted for.

Tanveer, Saleh A.↗

NASA NTRS1985

Aerodynamic analysis of a horizontal axis wind turbine by use of helical vortex theory, volume 2: Computer program users manual

A description of a computer program entitled VORTEX that may be used to determine the aerodynamic performance of horizontal axis wind turbines is given. The computer code implements a vortex method from finite span wind theory and determines the induced velocity at the rotor disk by integrating the Biot-Savart law. It is assumed that the trailing helical vortex filaments form a wake of constant diameter (the rigid wake assumption) and travel downstream at the free stream velocity. The program can handle rotors having any number of blades which may be arbitrarily shaped and twisted. Many numerical details associated with the program are presented. A complete listing of the program is provided and all program variables are defined. An example problem illustrating input and output characteristics is solved.

Keith, T. G., Jr.↗

NASA NTRS1978

Computational flow development for unsteady viscous flows: Foundation of the numerical method

A procedure is presented for effective consideration of viscous effects in computational development of high Reynolds number flows. The procedure is based on the interpretation of the Navier-Stokes equations as vorticity transport equations. The physics of the flow was represented in a form suitable for numerical analysis. Lighthill's concept for flow development for computational purposes was adapted. The vorticity transport equations were cast in a form convenient for computation. A statement for these equations was written using the method of weighted residuals and applying the Galerkin criterion. An integral representation of the induced velocity was applied on the basis of the Biot-Savart law. Distribution of new vorticity, produced at wing surfaces over small computational time intervals, was assumed to be confined to a thin region around the wing surfaces.

Bratanow, T.↗

NASA NTRS2013

Development of Polyimide Foam for Aircraft Sidewall Applications

In this paper, the use of polyimide foam as a lining in double panel applications is considered. It is being investigated here as a replacement for aircraft grade glass fiber and has a number of attractive functional attributes, not the least of which is its high fire resistance. The test configuration studied here consisted of two 1mm (0.04 in.) thick, flat aluminum panels separated by 12.7 cm (5.0 in.) with a 7.6 cm (3.0 in.) thick layer of foam centered in that space. Random incidence transmission loss measurements were conducted on this buildup, and conventional poro-elastic models were used to predict the performance of the lining material. Results from two densities of foam are considered. The Biot parameters of the foam were determined by a combination of direct measurement (for density, flow resistivity and Young s modulus) and inverse characterization procedures (for porosity, tortuosity, viscous and thermal characteristic length, Poisson s ratio and loss factor). The inverse characterization procedure involved matching normal incidence standing wave tube measurements of absorption coefficient and transmission loss of the isolated foam with finite element predictions. When the foam parameters determined in this way were used to predict the performance of the complete double panel system, reasonable agreement was obtained between the measured transmission loss and predictions made using a commercial statistical energy analysis code.

Silcox, Richard↗