Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “biodiesel blends”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Storage Stability of 50% Biodiesel Blends and Neat Biodiesel Produced in North America

This study investigated aging of two petroleum diesel, seven B100, three B20 blends, and 14 B50 blends representing the full range of fuels in the North American market for 12-weeks at 43 degrees Celsius under the ASTM D4625 accelerated aging protocol. Twelve-weeks under D4625 aging represents approximately 12 months of storage time in clean, dry conditions. Samples were taken every two weeks for measurement of Rancimat induction period (IP), peroxide content, and TAN; and total insoluble were measured at the end of the 12-week test.

09 BIOMASS FUELS↗
DOE OSTI2018

Re-additization of commercial biodiesel blends during long-term storage

Commercial biodiesel blends were aged at 43 degrees C while monitoring stability. The oxidation stability -- or oxidation reserve expressed as Rancimat induction period (IP) -- gradually decreased from its initial value. At a predetermined IP threshold, an antioxidant was used to restore IP to the ASTM D7467 specification minimum of 6 h, referred to as re-additization. At lower IP values, the amount of antioxidant required increased significantly, and the effectiveness tended to be reduced. Once IP fell to essentially zero, the acid content increased to above the allowable limit and insoluble material was also detected. Storage life was increased relative to the as-received fuels as evidenced by longer time to produce acids. Experience in the field may vary based on storage conditions; however, these results indicate re-additization can significantly increase storage life of biodiesel blends when used with regular monitoring of IP and acid number. An assessment of the storage stability of the as-received fuels showed that the initial IP did not predict storage behavior, although fuels above the specification minimum remained stable for >12 weeks accelerated aging (1 year simulated).

25 ENERGY STORAGE↗
DOE OSTI2020

Re-Additization of Commercial Biodiesel Blends During Long-Term Storage

Commercial biodiesel blends representative of the U.S. market were aged following procedure ASTM D4625, Standard Test Method for Middle Distillate Fuel Storage Stability at 43°C (110°F), with periodic monitoring of fuel properties indicative of oxidation. The oxidation stability—or oxidation reserve expressed as Rancimat induction period (IP)—gradually decreased from its initial value, as expected. At a predetermined IP threshold, an antioxidant was used to restore IP to the ASTM D7467 specification minimum of 6 six hours, referred to as re-additization. At lower IP values, the amount of antioxidant required increased significantly, and the effectiveness tended to be reduced. Once IP fell to essentially zero, the acid content increased to above the allowable limit. Insoluble material was detectable after the acid number increased out of specification. Storage life was increased with re-additization relative to the as-received fuels, as evidenced by longer time to produce acids. Experience in the field may vary based on storage conditions; however, these results indicate re-additization can significantly increase the storage life of biodiesel blends when used with regular monitoring of IP and acid number. An assessment of property changes during long-term storage showed the initial IP did not predict storage behavior, although fuels above the specification minimum remained stable for greater than 12 weeks of D4625 accelerated aging (1 one year simulated).

09 BIOMASS FUELS↗
DOE OSTI2024

Research to Address Technical Barriers to Expanded Markets for Biodiesel and Biodiesel Blends (CRADA Final Report)

NREL and the Clean Fuels Alliance America (CFAA) will work cooperatively to assess the effects of biodiesel blends on the performance of modern diesel engines. This work will include research to understand the impact of biodiesel blends on the operation and durability of particle filters and NO x control sorbents/catalysts, to quantify the effect on emission control systems performance, and to understand effects on engine component durability. This research was performed at NREL Renewable Fuels and Lubricants (REFUEL) laboratory (an engine testing laboratory) as well as at third party labs paid directly by CFAA with NREL as part of the project management team. Also, research to develop appropriate ASTM standards for biodiesel quality and stability was conducted in NREL’s bench scale fuel chemistry laboratory. The cooperative project involved laboratory testing and research at NREL using biodiesel from a variety of sources and in collaboration with a broad range of other stakeholders. In addition, NREL will work with NBB to set up an Industrial Steering Committee to design the scope for the various tasks and to provide technical oversight to these projects. NREL and NBB will cooperatively communicate the study results to as broad an audience as possible. This research benefits the public by expanding markets for a domestically produced low-carbon intensity fuel for use in diesel engines.

09 BIOMASS FUELS↗
DOE OSTI2019

Metals Analysis of Biodiesel Blends

The goal of this study was to compare metals analysis methods for biodiesel blends. Thirty-five B20 samples were collected from public stations and private fleets throughout the United States. All samples were analyzed for blend content and critical properties under the ASTM D7467 specification. Although not part of the specification, metals content, specifically Na, K, Ca, Mg, and P, is becoming an increasingly larger concern for industry. This study compared the metals content of the B20 samples using inductively coupled plasma atomic emission spectroscopy (ICP-AES), inductively coupled plasma mass spectrometry (ICP-MS), and microwave plasma atomic emission spectroscopy (MP-AES) methods. All three techniques showed improvements over the current detection limits of 1 ppm for Na, K, Ca, and Mg, and 5 ppm for P. Some differences were found between methods, but agreement was generally acceptable at the very low levels present in these samples. The MP-AES technique showed good promise for future development for this type of analysis.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2016

Impact of a Diesel High Pressure Common Rail Fuel System and Onboard Vehicle Storage on B20 Biodiesel Blend Stability

Adoption of high-pressure common-rail (HPCR) fuel systems, which subject diesel fuels to higher temperatures and pressures, has brought into question the efficacy of ASTM International specifications for biodiesel and biodiesel blend oxidation stability, as well as the lack of any stability parameter for diesel fuel. A controlled experiment was developed to investigate the impact of a light-duty diesel HPCR fuel system on the stability of 20% biodiesel (B20) blends under conditions of intermittent use and long-term storage in a relatively hot and dry climate. B20 samples with Rancimat induction periods (IPs) near the current 6.0-hour minimum specification (6.5 hr) and roughly double the ASTM specification (13.5 hr) were prepared from a conventional diesel and a highly unsaturated biodiesel. Four 2011 model year Volkswagen Passats equipped with HPCR fuel injection systems were utilized: one on B0, two on B20-6.5 hr, and one on B20-13.5 hr. Each vehicle was operated over a one-hour drive cycle in a hot running loss test cell to initially stress the fuel. The cars were then kept at Volkswagen's Arizona Proving Ground for two (35 degrees C average daily maximum) to six months (26 degrees C average daily maximum). The fuel was then stressed again by running a portion of the one-hour dynamometer drive cycle (limited by the amount of fuel in the tank). Fuel rail and fuel tank samples were analyzed for IP, acid number, peroxide content, polymer content, and ester profile. The HPCR fuel pumps were removed, dismantled, and inspected for deposits or abnormal wear. Analysis of fuels collected during initial dynamometer tests showed no impact of exposure to HPCR conditions. Long-term storage with intermittent use showed that IP remained above 3 hours, acid number below 0.3 mg KOH/g, peroxides low, no change in ester profile, and no production of polymers. Final dynamometer tests produced only small changes in fuel properties. Inspection of the HPCR fuel pumps revealed no deposits or abnormal wear for any fuel. The results provide some confidence that the ASTM D7467 stability requirement of 6 hr. minimum IP for B6 to B20 blends provides adequate protection for modern engine fuel systems.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2016

Effect of first and second generation biodiesel blends on engine performance and emission

The biodiesel is a potential source of alternative fuel which can be used at different proportions with diesel fuel. This study experimentally investigated the effect of blend percentage on diesel engine performance and emission using first generation (soybean) and second generation (waste cooking) biodiesel. The characterization of the biodiesel was done according to ASTM and EN standards and compared with ultralow sulfur diesel (ULSD) fuel. A multi-cylinder test bed engine coupled with electromagnetic dynamometer and 5 gas analyzer were used for engine performance and emission test. The investigation was made using B5, B10 and B15 blends for both biodiesels. The study found that brake power (BP) and brake torque (BT) slightly decreases and brake specific fuel consumption (BSFC) slightly increases with an increase in biodiesel blends ratio. Besides, a significant reduction in exhaust emissions (except NO{sub x} emission) was found for both biodiesels compared to ULSD. Soybean biodiesel showed better engine performance and emissions reduction compared with waste cooking biodiesel. However, NO{sub x} emission for B5 waste cooking biodiesel was lower than soybean biodiesel.

09 BIOMASS FUELS↗
DOE OSTI2021

Consumer Guide to Biodeisel

Learn about biodiesel fuel and how, when combined with vehicles with diesel engines, it can be a green transportation choice. This fact sheet from Energy Saver also includes information on biodiesel blends, biodiesel performance, and downsides of biodiesel.

biodiesel, vehicles, transportation, diesel engine↗
DOE OSTI2017

Biodiesel Basics

This fact sheet (updated for 2017) provides a brief introduction to biodiesel, including a discussion of biodiesel blends, which blends are best for which vehicles, where to buy biodiesel, how biodiesel compares to diesel fuel in terms of performance, the difference between biodiesel and renewable diesel, how biodiesel performs in cold weather, whether biodiesel use will plug vehicle filters, how long-term biodiesel use may affect engines, biodiesel fuel standards, and whether biodiesel burns cleaner than diesel fuel. The fact sheet also dismisses the use of vegetable oil as a motor fuel.

09 BIOMASS FUELS↗
DOE OSTI2017

Biodiesel Basics

This fact sheet (updated for 2017) provides a brief introduction to biodiesel, including a discussion of biodiesel blends, which blends are best for which vehicles, where to buy biodiesel, how biodiesel compares to diesel fuel in terms of performance, the difference between biodiesel and renewable diesel, how biodiesel performs in cold weather, whether biodiesel use will plug vehicle filters, how long-term biodiesel use may affect engines, biodiesel fuel standards, and whether biodiesel burns cleaner than diesel fuel. The fact sheet also dismisses the use of vegetable oil as a motor fuel.

biodiesel, blends, B5, B2, B100, B20, ASTM D975, A↗
DOE OSTI2023

Statistical Treatise on Critical Biodiesel (B100) Quality Properties in the United States from 2004-2022

The quality of neat biodiesel (B100) is critical for ensuring biodiesel blends used in diesel-powered vehicles do not adversely impact engine performance. In the United States, B100 is required to meet ASTM International's purity and fuel property requirements in D6751, "Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels." Here we review the development of this standard for the different grades of B100. The BQ-9000 program, which currently covers over 90% of U.S. and Canadian production volumes, is also described. Engine and original equipment manufacturers have expressed a desire for credible, third-party data on values of various ASTM B100 properties in the commercial market to inform their efforts to address future emissions and durability requirements. To address this need, the National Renewable Energy Laboratory published data from analysis and testing of monthly samples from BQ-9000 producers from calendar years 2017-2022, resulting in 300-500 data points (i.e., individual fuel samples) per year. These data and a statistical evaluation of properties including the average, mean, standard deviation, and 95th or 5th percentile are presented. The results show very consistent and high-quality B100 produced in this time frame. Additionally, we review the results of earlier quality surveys conducted in the United States between 2004 and 2011, revealing how quality has changed over time in response to ASTM standard revisions, as well as the significant overall improvement in quality for modern biodiesel production.

ASTM standard↗
DOE OSTI2023

Decarbonization of Liquid Heating Fuels

Annually, residential and commercial buildings use about 5 billion gallons (18.9 billion liters) of distillate fuel for space and water heating. There is considerable interest in decarbonizing these markets through a combination of heat pumps and a future, carbon-free grid. An alternate approach that offers rapid and cost effective decarbonization involves substitution of low-carbon biofuels for fossil fuels within this market. Heating fuel marketers in North America and Europe are aggressively moving to achieve market penetration of biofuels. Processes for this include fuel specification standards, development of manufacturer-approved burners and all system components, development of standards for equipment listing, installation code changes, and generation of performance data. There has been considerable progress in these areas and each of these are reviewed in this paper. Currently, the most important biofuel for this market is biodiesel with a U.S. production capacity of 2.4 billion gallons (9.1 billion liters) and approximately a 75% reduction in GHG emissions. The biodiesel industry has stated a vision for dramatic increases in biodiesel production over the next decades. Fuel and equipment standards are in place to enable use of biodiesel blends to 20% and this blend is now widely used. Standard changes to extend this to as high as 100% biodiesel are nearing completion. Several states have implemented requirements for minimum levels of biodiesel in heating oil with these levels increasing over time.

09 BIOMASS FUELS↗
DOE OSTI2018

Influence of biodiesel decomposition chemistry on elastomer compatibility

Here, the compatibility of biodiesel blends with five common elastomers (acrylonitrile rubber or NBR, fluorocarbon, neoprene, ethylene propylene diene monomer or EPDM, and silicone) was assessed using Hansen solubility parameters. A solubility analysis was performed over the full diesel blend range and the model used methyl hydroperoxide, acetaldehyde, and formic acid to represent the decomposition products of biodiesel. An empirical study was also conducted to determine the efficacy of the approach to predict the volume swell of elastomers. This study included the influence of biodiesel with acetaldehyde and formic acid. The solubility model showed good agreement with measured volumes for fluorocarbon, neoprene, EPDM, and silicone. However, solubility curves for NBR did not reflect the measured volume changes, and therefore the solubility parameters used for NBR in this study are not considered reliable. The results showed that formic acid caused higher swelling in NBR, fluorocarbon, neoprene, and silicone than did acetaldehyde. For EPDM, the measured volume decreased with both biodiesel concentration and the addition of formic acid.

09 BIOMASS FUELS↗
DOE OSTI2016

Evaluation of fuel-borne sodium effects on a DOC-DPF-SCR heavy-duty engine emission control system: Simulation of full-useful life

Here we report that for renewable fuels to displace petroleum, they must be compatible with emissions control devices. Pure biodiesel contains up to 5 ppm Na + K and 5 ppm Ca + Mg metals, which have the potential to degrade diesel emissions control systems. This study aims to address these concerns, identify deactivation mechanisms, and determine if a lower limit is needed. Accelerated aging of a production exhaust system was conducted on an engine test stand over 1001 h using 20% biodiesel blended into ultra-low sulfur diesel (B20) doped with 14 ppm Na. This Na level is equivalent to exposure to Na at the uppermost expected B100 value in a B20 blend for the system full-useful life. During the study, NOx emissions exceeded the engine certification limit of 0.33 g/bhp-hr before the 435,000-mile requirement. Replacing aged diesel oxidation catalyst (DOC), diesel particulate filter (DPF), and selective catalytic reduction (SCR) devices with new degreened parts showed that each device contributed equally to the NOx increase. Following this systems-based evaluation, a detailed investigation of the individual components was completed. Na was determined to have minimal impact on DOC activity. For this system, it is estimated that B20-Na resulted in 50% more ash into the DPF. However, the Na did not diffuse into the cordierite DPF nor degrade its mechanical properties. The SCR degradation was found to be caused by a small amount of precious group metals (PGM) contamination that increased NH3 oxidation, and lowered NOx reduction. Therefore, we determined that the primary effect of Na in this study is through increased ash in the DPF rather than deactivation of the catalytic activity.

42 ENGINEERING↗
DOE OSTI2023

Water Contamination Impacts on Biodiesel Antioxidants and Storage Stability

Biodiesel (fatty acid methyl esters) can oxidize in storage to form acids and gums that negatively impact engine performance and durability. Antioxidant additives are used to increase biodiesel storage stability, and previous studies that evaluated the effectiveness of antioxidants demonstrated that more polar antioxidants tend to be the most effective (provide the largest improvement in stability per unit of antioxidant added). However, polar antioxidants have significant water solubility, and diesel fuel storage tanks are commonly contaminated with water (forming a layer of water under the fuel). This study investigates whether nonpolar antioxidants, which are less effective in dry environments, might be more effective under wet conditions simulating real-world storage. Biodiesel blends treated with polar and nonpolar antioxidants were subjected to accelerated aging using the ASTM D4625 protocol (storage at 43 °C, open to air, for up to 24 weeks) both with and without added water. Fuels treated with polar/higher-effectiveness compounds and stored in contact with water (simulating water in a storage tank) or high humidity showed accelerated loss of stability compared to dry storage. The same fuel treated with a nonpolar antioxidant and stored in the same conditions did not exhibit accelerated stability loss and thus had higher storage stability over the long term despite treatment with an initially less effective additive. Analysis of the fuels during aging showed that this loss of stability was not due to oxidation but rather extraction of the polar antioxidant into the water layer. Antioxidant additives that are incompatible with wet or humid storage conditions were found to cause faster-than-anticipated loss of stability, which was preventable with use of nonpolar additives.

09 BIOMASS FUELS↗
DOE OSTI2016

NO 2 oxidation reactivity and burning mode of diesel particulates

The NO 2 oxidation kinetics and burning mode for diesel particulate from light-duty and medium-duty engines fueled with either ultra low sulfur diesel or soy methyl ester biodiesel blends have been investigated and are shown to be significantly different from oxidation by O 2 . Oxidation kinetics were measured using a flow-through packed bed microreactor for temperature programmed reactions and isothermal differential pulsed oxidation reactions. The burning mode was evaluated using the same reactor system for flowing BET specific surface area measurements and HR-TEM with fringe analysis to evaluate the nanostructure of the nascent and partially oxidized particulates. The low activation energy measured, specific surface area progression with extent of oxidation, HR-TEM images and difference plots of fringe length and tortuosity paint a consistent picture of higher reactivity for NO 2 , which reacts indiscriminately immediately upon contact with the surface, leading to the Zone I or shrinking core type oxidation. In comparison, O 2 oxidation is shown to have relatively lower reactivity, preferentially attacking highly curved lamella, which are more reactive due to bond strain, and short lamella, which have a higher proportion of more reactive edge sites. Furthermore, this preferential oxidation leads to Zone II type oxidation, where solid phase diffusion of oxygen via pores contributes significantly to slowing the overall oxidation rate, by comparison.

33 ADVANCED PROPULSION SYSTEMS↗