SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The Marine Algae Industrialization Consortium (MAGIC) works to solve pressing challenges in the commercialization of sustainable microalgae production as a feedstock for biofuel and other bioproducts.
Algae cultivation and processing is an important pathway under discussion within the broader CO 2 capture and utilization umbrella. Here, we discuss the results of a life-cycle analysis and techno-economic analysis of a pilot-scale photobioreactor that uses flue gas directly from natural gas or biogas combustion at 3–5% CO 2 concentration. The system requires minimal freshwater use as it has been successfully run with industrial wastewater and has a much smaller areal footprint compared with open pond cultivation. Introducing the flue gas directly to the photobioreactor avoids the need for CO 2 separation and pressurization, which is undertaken in many other algae cultivation systems. For the end-use of the biomass, the default case assumes conversion of algae to liquid fuels via hydrothermal liquefaction. The results indicate that the pilot-scale system has a higher cost, and comparable greenhouse gas emissions compared to pond-based systems, especially as the grid is anticipated to evolve to a lower carbon intensity. The costs of algae biofuel production range from $\$12–16$ per GGE at the current pilot scale. Depending on whether the source of the carbon is fossil or biogenic, the net emissions are 68 g CO 2 e per MJ and −4 g CO 2 e per MJ respectively. If the marine algae species is used instead of the freshwater species, it offers an additional 16 g CO 2 e per MJ carbon fixation in the form of calcium carbonate. The findings point to broadly desirable trends in GHG emissions and costs, while the discussion aims to shed light on areas that could further improve the scalability of the system.
Microalgae cultivation on wastewater can provide remediation and generate valuable feedstocks for biofuel production. Wastewater algae typically have a high percentage of inorganic ash, which can reduce yield and quality of biocrude produced during hydrothermal liquefaction (HTL). Here, in this work, we evaluated the ability of hydrocyclone pre-processing to remove inorganic ash from wastewater algae. The pH of the algae slurry was adjusted to 9.5 to encourage the formation of precipitates and create a density differential between ash particles and algal cells. Hydrocyclone processing successfully concentrated ash particles in the underflow fraction and reduced the total ash percentage in the overflow fraction. Overall, hydrocyclone processing reduced the total ash by 21%, while only 8% of organics were lost. Elemental and mineral analysis showed that Mg and P were concentrated in the underflow in the form of baricite (an isomorph of vivianite). Future research should focus on improving vivianite and/or baricite formation, and therefore ash removal, by providing a reducing environment. The addition of multiple hydrocyclones in series could also improve the removal of ash. We concluded that hydrocyclone treatment of wastewater algae is a feasible method to remove inorganic ash, but further process optimization is required.
Genome assembly and annotation of the biofuel- and bioproduct-relevant microalga Nannochloropsis oceanica CCAP849/10
This paper evaluates the potential of algae-derived biobinders as sustainable alternatives for pavement construction. It specifically examines the physicochemical and rheological properties of biomodified binders and their potential to offset carbon emissions when used as partial replacements for conventional petroleum-based asphalt binders. Biosequestration of CO 2 using microalgal cell factories is a promising way of recycling CO 2 into biomass via photosynthesis. Our study demonstrates that incorporating algae-derived binders into asphalt can significantly reduce carbon emissions. Each 1% increase in algae-based biobinder leads to an approximate 4.5% decrease in net carbon emissions. This indicates that a blend containing about 22% biobinder has the potential to achieve carbon neutrality. Blends with higher proportions may even result in net-negative emissions, highlighting a promising strategy for environmentally responsible road construction. In terms of performance, the study shows that certain algae-derived biobinders significantly enhance the cracking resistance of asphalt, particularly under subzero temperatures, by improving its stress-relief capacity. A key contribution of this work is the introduction of polarizability as a novel molecular-level parameter for assessing the compatibility of algae-derived bio-oils with asphalt. By capturing the electronic responsiveness of bio-oil molecules, polarizability serves as a predictive indicator of their interaction potential with asphalt components, providing a new dimension for evaluating the binder performance at the molecular scale. Among the tested materials, the biobinder derived from Haematococcus pluvialis demonstrated particularly strong improvements in resistance to permanent deformation under repeated loading conditions analogous to traffic-induced stress, as well as enhanced resistance to moisture-induced damage. In conclusion, these findings advance the chemistry-driven design of biomass-based binders and highlight a promising pathway toward the development of low-carbon, high-performance, and sustainable infrastructure materials.
This project was proposed in response to the FY19 Bioenergy Technologies Office Multi-Topic Funding Opportunity Announcement DE-FOA-0002029, Area of Interest Subtopic 1 (AOI1): Cultivation Intensification Processes for Algae. The main challenge identified by the FOA was “in translating results between laboratory research systems and larger-scale outdoor (or mass culture) systems. These difficulties limit reliable experimental durations, adequate and representative experimental volumes of material, and results that can be reproduced reliably. By overcoming the challenge in translating results between laboratory and mass cultures, the objective of AOI 1 is to increase the harvest yield, robustness, and quality of algae cultivation for biofuels and bioproducts”. This report marks the final technical deliverable of this project and reviews all the major findings of the research program.
In order to fully exploit algae carbon assimilation for fuels, a preqrequisite is high photosynthetic efficiency and carbon conversion to fuel precursors. In the context of this collaborative project between NLR and EMRE we aim to address aspects of both the biological constraints around photosynthesis-driven carbon assimilation flux as well as elements that bridge the gap between laboratory cultivation and meaningful outdoor deployment, building on the unique capabilities of NLR and EMRE’s algae bioengineering teams. The goal of this work is to improve our understanding of key cellular biochemistry, mass cultivation, and biomass conversion constraints that presently limit the potential bio-oil yield. The proposed first phase of this work will focus on biomass growth improvements by testing hypotheses for alleviating identified metabolic and photophysiological bottlenecks. The results of this work could inform decisions by stakeholders (e.g., industry, community, investors) on the design and deployment of a sustainable biofuel supply chain from algae.
The goal of this project was to develop and demonstrate an integrated system for algal biofuel production system and wastewater treatment that can produce low-cost drop-in biofuels. Experimental data and techno-economic analysis showed the ability to produce drop-in biofuels from wastewater derived algal biomass at a cost of $3.32 and identified methods to further reduce costs. In particular, when accounting for wastewater treatment cost savings relative to conventional processes, the proposed integrated system can support a negative minimum fuel selling price. This means the normal costs of wastewater treatment are sufficient to cover all the costs of biofuel production with the integrated system.
This project focused on developing advanced optical coatings to improve solar energy utilization. The research aimed to create lanthanide-doped upconversion nanoparticles (UCNPs) capable of capturing unused near-infrared (NIR) light from the sun and converting it into visible light (blue and red photons) that can be used for photosynthesis. The primary goal was to identify, synthesize, and integrate highly efficient UCNPs into a transparent thin-film device. Through a comprehensive workflow involving computer simulations, high-throughput robotic synthesis, and detailed optical characterization, the project successfully developed a high-performance material. The key technical achievement was the creation of a core-shell UCNP (NaYF₄:20%Yb³⁺, 2%Er³⁺ coated with a 10 nm NaYF₄ shell) that demonstrated a quantum yield of 3.2% for converting 980 nm NIR light into visible light. Transparent thin films fabricated from these nanoparticles showed excellent optical properties, confirming their potential for practical applications. This research adds to the scientific understanding of energy transfer in lanthanide materials and demonstrates a technically effective method for creating efficient light-converting coatings. The primary benefit to the public lies in the potential for these coatings to enhance the efficiency of solar-driven processes, such as boosting the growth of algae in photobioreactors for biofuel production.
Introduction: Microalgae constitute a prominent feedstock for producing biofuels and biochemicals by virtue of their prolific reproduction, high bioproduct accumulation, and the ability to grow in brackish and saline water. However, naturally occurring wild type algal strains are rarely optimal for industrial use; therefore, bioengineering of algae is necessary to generate superior performing strains that can address production challenges in industrial settings, particularly the bioenergy and bioproduct sectors. One of the crucial steps in this process is deciding on a bioengineering target: namely, which gene/protein to differentially express. These targets are often orthologs which are defined as genes/proteins originating from a common ancestor in divergent species. Although bioinformatics tools for the identification of protein orthologs already exist, processing the output from such tools is nontrivial, especially for a researcher with little or no bioinformatics experience. Methods: The present study introduces AlgaeOrtho, a user-friendly tool that builds upon the SonicParanoid orthology inference tool (based on an algorithm that identifies potential protein orthologs based on amino acid sequences) and the PhycoCosm database from JGI (Joint Genome Institute) to help researchers identify orthologs of their proteins of interest in multiple diverse algal species. Results: The output of this application includes a table of the putative orthologs of their protein of interest, a heatmap showing sequence similarity (%), and an unrooted tree of the putative protein orthologs. Notably, the tool would be instrumental in identifying novel bioengineering targets in different algal strains, including targets in not-fully annotated algal species, since it does not depend on existing protein annotations. We tested AlgaeOrtho using three case studies, for which orthologs of proteins relevant to bioengineering targets, were identified from diverse algal species, demonstrating its ease of use and utility for bioengineering researchers. Discussion: This tool is unique in the protein ortholog identification space as it can visualize putative orthologs, as desired by the user, across several algal species.
Large-scale algae farms may someday become a consistent source of biomass feedstock for biofuels. Near-term supplies of algal biomass are available at certain water resource recovery facilities as algae cultivation is used as a method for nutrient recovery from specific effluent streams. Algae grown as a service shifts the value to the service rather than its sole use as a feedstock, which could enable the provision of algal biomass at low to no cost to biofuel producers. Hydrothermal liquefaction (HTL) can readily upgrade wet feedstock slurries, such as algae, to produce a carbon-enriched biocrude. The HTL biocrude can be hydrotreated and distilled, producing a variety of distillate fuels, including synthetic aviation fuel (SAF). We present a pathway, showing the experimental production of SAF from wastewater-grown algae via HTL, along with a techno-economic assessment to identify opportunities for process improvements. Critical quality attributes of the SAF, such as density, viscosity, surface tension, and freeze point, were estimated within the expected fuel experience ranges when compared against petroleum jet fuel. The average minimum fuel selling price of fuels from wastewater-grown algae for breakeven economics was $\$9.04$ per gasoline gallon equivalent (GGE). The sale of co-products such as struvite fertilizers and cement additives can add revenue to reduce the net cost. Ultimately, the selling price is influenced by the scale of the HTL processing facility. Adjusting estimations in the process scale, algae yield, and capital cost estimation can lower the price to $\$6.51$/GGE or raise it to $13.07/GGE.
Microalgae are promising sources to sustainably meet the global needs for energy and products. Algae grow under different trophic conditions, where nutritional status regulates biosynthetic pathways, energy production, and growth. The green alga Chromochloris zofingiensis has strong economic potential because it co-produces biofuel precursors and the high-value antioxidant astaxanthin while accumulating biomass when grown mixotrophically. As an emerging reference alga for photosynthesis, metabolism, and bioproduction, C. zofingiensis needs a defined, optimized medium to standardize experiments during fast growth for batch cultivation. Because the interplay of glucose treatment (+Glc) and mineral deficiency influences photosynthesis, growth, and the production of lipids and astaxanthin, we designed a replete nutrient medium tailored to the C. zofingiensis cellular ionome. We combined inductively coupled plasma mass spectrometry (ICP-MS) and +Glc growth curves to determine a medium that is nutrient replete for at least 5 days of +Glc logarithmic growth. We found that there are high nutritional needs for phosphorus and sulfur during mixotrophy. Iron was the only element measured for which the cellular concentration correlated with exogenous concentration and was iteratively adjusted until the cellular ionome was consistent through the logarithmic growth phase. This Chromochloris-Optimized Ratio of Elements (CORE) medium supports fast growth and high biomass and lipid accumulation without causing excess nutrient toxicity. This defined, nutrient-replete standard is important for future C. zofingiensis investigations and can be adapted for other species to support high biomass for batch cultivation. The method used to develop CORE medium shows how ionomics informs replicable media design and may be applied in industrial settings to inform cost-effective biofuel production.
Algal biochar, as the solid residue of biofuel production from algal biomass, is reported to explore disposition options, aiming to lessen the liability or obstacles to biofuel production processes. However, landfills and open combustion lead to adverse environmental impacts. One way to add value to such wastes is to use them as admixtures in cementitious construction materials. This study aims to investigate the feasibility of algae-derived biochar as supplementary cementitious materials (SCM) at different water contents and mixture ratios. Algal biochar-cement composites were prepared with different algal biochar content as well as different water-to-cement (w/c) ratios, and the surface area, morphology, elemental, and mineralogical composition were characterized. To compensate for the high-water absorption of algal biochar, a small concentration of a superplasticizer was used since higher w/c ratios negatively impact strength. The mechanical performance of algal biochar-cement composites is compared with control composites using commercial silica fume as a typical commercial SCM. The findings suggest that algal biochar is a promising candidate to replace commercial SCM, like silica fume, since algal biochar-cement composites can reach comparable compressive strength and Young’s modulus to commercial pozzolan-cement materials with the same w/c ratio, though at later curing times, 33 days. Although the tensile strength of algal biochar-cement composites is statistically similar at 7 days, it is significantly lower at later curing times, and further investigation is required to improve this property. Algal biochar-based cement binders showed comparable embodied carbon to silica fume-based cement binders based on a cradle-to-gate lifecycle analysis. However, the ability of algal biochar to absorb large volumes of CO 2 over short periods of time, as measured in this study, makes this novel SCM an excellent alternative to reduce the embodied carbon of concrete structures cradle-to-grave at 1/10 of the cost. In conclusion, valorization of algae-derived solid waste provides great potential to reduce embodied carbon and brings credit to biofuel production and concrete-based construction.
This technology case study report details the cost and sustainability prospects for an emerging feedstock - microalgae - converted to fuels and products via a fractionation and upgrading approach termed combined algae processing (CAP). Detailed techno-economic analysis (TEA) and life cycle analysis (LCA) are conducted for the conversion of farmed algae biomass, with two primary scenarios considering the conversion of either high-compositional-quality biomass enriched in lipids (high-lipid [HL]) or lower-quality biomass enriched in protein (high-protein [HP]). Each scenario employs a different biorefinery configuration tailored towards extracting the maximum value from the given biomass composition. The HL scenario produces fuels and non-isocyanate polyurethane (NIPU) as the primary products, while the HP scenario products fuels and a residual solid coproduct which can be used as a co-feed for producing thermoplastics. The results for the HL scenario were particularly promising, with a minimum fuel selling price (MFSP) of $\$$3.68 per gasoline gallon equivalent (GGE) and fuel GHG emissions translating to 54%-76% reduction compared to petroleum fuels depending on the coproduct handling method used. In contrast, the HP scenario faced more challenges in producing biofuels economically, projecting an MFSP of $\$$7.92/GGE despite significant revenues from the residual algae solids. LCA results for the HP case reflected a 24% reduction potential in biorefinery-level GHG emissions. However, these GHG reductions were primarily associated with the thermoplastic coproduct, which accounted for 93% of all biorefinery outputs by mass. Using a process-level allocation method, carbon intensity results were less promising, indicating a net increase in fuel GHG emissions versus petroleum fuels and highlighting the reliance of this scenario on the thermoplastic coproduct.
This white paper summarizes the historical progress and perspectives on future opportunities for Combined Algae Processing (CAP), a conversion approach centered around fractionating microalgae biomass and producing a slate of fuels and products. We discuss the critical challenges associated with the commercialization of algal biofuels and demonstrate how the CAP approach is uniquely suited to overcome these barriers. The versatility of applying CAP to various sources of algae is highlighted along with conversion to various fuels and product options.
Polyurethane is a versatile material with a wide range of applications in the production of foam products such as car seats, mattresses, footwear, insulation foam, and more. The traditional process for producing polyurethane foam involves the fast reaction of isocyanate with water, which generates CO2 as a blowing agent. However, the use of isocyanate has raised concerns due to its potential for causing allergic reactions and aspiration symptoms. This has led to increased regulation of isocyanate, leading to a growing interest in developing alternatives. Non-isocyanate polyurethane (NIPU) has emerged as a promising alternative to traditional toxic PU production. The most promising approach for producing NIPU is the aminolysis of cyclic carbonate with diamine. The NIPU produced through this process has a polyhydroxyurethane structure, which is similar to traditional PU chemistry. We have demonstrated that microalgal oil is a favored feedstock, as it can provide high reactivity for industrial applications. However, the NIPU production process does not generate gas, and a blowing agent is required to achieve the desired foam structure. One of the challenges in producing NIPU foam is to match the bubble formation and curing rates. We have developed a novel approach to producing NIPU foam that utilizes carbamate as a bifunctional blowing and crosslinking agent. We have used vegetable oil and microalgal oil as feedstocks to produce various NIPU for characterization. The development of microalgal NIPU provides an exciting opportunity for reducing the environmental impact of foam production and improving the safety of the materials used in the production process. The production of value-added NIPU foam can also drive down the cost of microalgal biorefinery, advancing the commercialization of microalgal biofuel.
This report summarizes the research at Pacific Northwest National Laboratory (PNNL) to evaluate the economic viability and environmental impact of using microalgae to produce fuels and other products via hydrothermal liquefaction (HTL). Over the past several years, PNNL has examined key aspects of feedstock cost and availability, formatting and conversion techniques, and the utilization of all HTL products. Investigations of feedstock cost led to opportunities to work with cost-advantaged algal feedstocks that can be provided at minimal cost for HTL processing. Cost-advantaged algae include wastewater-grown algae and harvested algal blooms. Although farm-cultivated algae offer the best possible biomass composition and scalability for HTL processing, the cost of the feedstock is too high to yield an economically competitive biofuel. Processing cost-advantaged feedstocks creates other unique challenges in adapting HTL to upgrade biomass with higher than typical ash content and less preferred composition (low lipid). Despite the challenges, HTL of cost-advantaged algae results in economically competitive pricing scenarios and significant advantages in reducing net emissions below 70% of the petroleum baseline. The utilization of a variety of potential non-fuel products from algal HTL, such as the use of HTL solids as a cement additive, provides a significant reduction in net emissions by offsetting emissions from other carbon-intense products. This report presents an analysis of the research conducted at PNNL to develop an economically and environmentally beneficial process for algae HTL.
This Final Technical Report summarizes the goals, approach, and outcomes of the project “Enhanced Production of Algae Lipids and Carbohydrates for Fuel and Polyurethane Precursors”. The project addressed the challenge of improving microalgae biomass productivity and simultaneously producing valuable polyurethane precursors (PUPs), from both lipids and carbohydrates, that can be converted into renewable biofuels and bio-based polyurethane (PU) products. By integrating advanced genetic engineering, traditional breeding, high-throughput screening, pilot cultivation, and chemical conversion technologies, the team achieved significant advancements in algae biotechnology.