Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WS2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Surface Chemistry, Friction, and Wear Properties of Untreated and Laser-Annealed Surfaces of Pulsed-Laser-Deposited WS(sub 2) Coatings

An investigation was conducted to examine the surface chemistry, friction, and wear behavior of untreated and annealed tungsten disulfide (WS2) coatings in sliding contact with a 6-mm-diameter 440C stainless-steel ball. The WS2 coatings and annealing were performed using the pulsed-laser-deposition technique. All sliding friction experiments were conducted with a load of 0.98 N (100 g), an average Hertzian contact pressure of 0.44 GPa, and a constant rotating speed of 120 rpm. The sliding velocity ranged from 31 to 107 mm/s because of the range of wear track radii involved in the experiments. The experiment was performed at room temperature in three environments: ultrahigh vacuum (vacuum pressure, 7X(exp -10) Pa), dry nitrogen (relative humidity, less than 1 percent), and humid air (relative humidity, 15 to 40 percent). Analytical techniques, including scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDX), x-ray photo electron spectroscopy (XPS), surface profilometry, and Vickers hardness testing, were used to characterize the tribological surfaces of WS2 coatings. The results of the investigation indicate that the laser annealing decreased the wear of a WS2 coating in an ultrahigh vacuum. The wear rate was reduced by a factor of 30. Thus, the laser annealing increased the wear life and resistance of the WS2 coating. The annealed WS 2 coating had a low coefficient of friction (less than O.1) and a low wear rate ((10(exp -7) mm(exp 3)/N-m)) both of which are favorable in an ultrahigh vacuum.

Miyoshi, Kazuhisa↗
NASA NTRS1989

A Spinoff from Mariner

Among the technologies incorporated into the later Mariner missions was a dry film lubricant which offered exceptional lubrication quality for reduced friction and extended wear-life of mating parts in harsh interplanetary environments. Micro Surface Corporation acquired this technology, and currently market it as WS2 modified tungsten disulfide coating. A pressurized refrigerated air application process impinges a dry metallic WS2 coating without heat, curing, binders or adhesives. The coating binds instantly to metal or resin substrates with a 20 millionths of an inch thickness. Performance has been excellent in a variety of industries, particularly in plastics where in some operations, the coating increases production by reducing drag between tool steel and resin. Other advantages include product quality improvement, extension of equipment service life and maintenance elimination or reduction.

Source record↗
NASA NTRS1973

High temperature solid lubricants: When and where to use them

The state of the art of solid lubrication for moderate to extremely high temperature lubrication (to 1600 F) is reviewed. Lubricating characteristics, stability in various environments, and relevant machine design considerations are discussed. Lubricating materials discussed include the layer lattice compounds: MoS2, WS2, graphite and graphite fluoride, the high temperature polyimide polymer, and calcium fluoride based coating and composites. The scope of the information includes results from wear testers, ball bearing, and journal bearings.

Sliney, H. E.↗
NASA NTRS1973

High temperature solid lubricants - When and where to use them.

This paper reviews the state of the art of solid lubrication for moderate to extremely high temperature lubrication (to 1600 F). Lubricating characteristics, stability in various environments, and relevant machine design considerations are discussed. Lubricating materials discussed include MoS2, WS2, graphite, graphite fluoride, the high temperature polymide polymer, and calcium fluoride based coatings and composites. The scope of the information includes results from wear testers, ball bearings, and journal bearings.

Sliney, H. E.↗
NASA NTRS1978

Sputtering technology in solid film lubrication

Potential and present sputtering technology is discussed as it applies to the deposition of solid film lubricants particularly MoS2, WS2, and PTFE. Since the sputtered films are very thin, the selection of the sputtering parameters and substrate condition is very critical as reflected by the lubricating properties. It was shown with sputtered MoS2 films that the lubricating characteristics are directly affected by the selected sputtering parameters (power density, pressure, sputter etching, dc-biasing, etc.) and the substrate temperature, chemistry, topography and the environmental conditions during the friction tests. Electron microscopy and other surface sensitive analytical techniques illustrate the resulting changes in sputtered MoS2 film morphology and chemistry which directly influence the film adherence and frictional properties.

Spalvins, T.↗
NASA NTRS1978

Sputtering technology in solid film lubrication

Current and potential sputtering technology is reviewed as it applies primarily to the deposition of MoS2, though such lubricants as WS2 and PTFE are also considered. It is shown by electron microscopy and surface sensitive analytical techniques that the lubricating properties of sputtered MoS2 films are directly influenced by the sputtering parameters selected (i.e., power density, pressure, sputter etching, dc-biasing, etc.), substrate temperature, chemistry, topography, and environmental conditions during the friction test. Electron micrographs and diffractograms of sputtered MoS2 films clearly show the resultant changes in film morphology which affect film adherence and frictional properties.

Spalvins, T.↗
NASA NTRS1993

Atomic oxygen interaction with spacecraft materials: Relationship between orbital and ground-based testing for materials certification

The effects of atomic oxygen on boron nitride (BN), silicon nitride (Si3N4), Intelsat 6 solar cell interconnects, organic polymers, and MoS2 and WS2 dry lubricant, were studied in Low Earth Orbit (LEO) flight experiments and in a ground based simulation facility. Both the inflight and ground based experiments employed in situ electrical resistance measurements to detect penetration of atomic oxygen through materials and Electron Spectroscopy for Chemical Analysis (ESCA) analysis to measure chemical composition changes. Results are given. The ground based results on the materials studied to date show good qualitative correlation with the LEO flight results, thus validating the simulation fidelity of the ground based facility in terms of reproducing LEO flight results. In addition it was demonstrated that ground based simulation is capable of performing more detailed experiments than orbital exposures can presently perform. This allows the development of a fundamental understanding of the mechanisms involved in the LEO environment degradation of materials.

Cross, Jon B.↗
NASA NTRSDate not supplied

Metallic Environmentally Resistant Coating Rapid Innovation Initiative

Lightweight alloys such as aluminum (Al) and titanium (Ti) are often specified for space systems to minimize mass while maintaining structural integrity [1,2]. Such alloys however, have poor tribological response (high friction and wear), especially in extreme space environments, which becomes worse with the additional presence of lunar regolith. This leads to short lifetimes and premature failures that will ultimately limit long term operations on the lunar surface [2]. This project is addressing this technology gap by developing advanced wear- and radiation-resistant coatings for lightweight parts to extend the life-time and sustainability of both lunar and Martian assets. Ceramics were considered for their high wear resistance, but were rejected because of their low fracture toughness, which would be especially problematic for structural components. The novel and existing coating technologies and deposition methods are being tested in this project. The coating materials are Boron Nitride-Aluminum (BN-Al), Nickle Titanium (NiTi), Aluminum Oxide (AlO3), Ti64 with hBN at 2 and 10 vol percent (Ti-2vol%hBN and Ti-10vol%hBN), and the deposition techniques are high pressure cold-spray (CS) and ambient and vacuum plasma-spray (APS and VPS) [3,4,5]. BN-Al, NiTi, Ti-2vol%hBN, and Ti-10vol%hBN were applied with all three deposition techniques, and AlO3 was applied only using the APS deposition technique. A tungstenite (WS2) film was applied to the NiTi VPS coating. The coating and deposition technique configurations are being tested against several key end-use performance parameters. The parameters include the capabilities of the coatings under wear environments such as regolith simulant, thermal cycling from high (120°C) to cryogenic (-173°C), high vacuum (~10-7 torr), and pre- and post-exposure to ionizing particle radiation. Wear tests include pin on disk, three-body abrasion, and surface erosion by high velocity regolith impacts. The initial down selection is being performed using on virgin and environmental exposure samples using pin on disk and three body abrasion wear tests. From preliminary assessment of this testing, a few configurations were eliminated. Ti-10vol%hBN could not be applied using CS application and NiTi could not be applied using APS or CS application so these configurations did not get tested. Early pin on disk wear tests showed poor wear performance of BN-Al so this coating was eliminated early in the testing process. AlO3 on Al substrate did not survive thermal cycling, but wear testing is continuing for AlO3 on Ti substrate. A more detailed analysis is being con-ducted to further reduce the number of configuration for phase II and III. Phase II testing will include conventionally and additively manufactured substrates with surface erosion testing. In phase III, the coatings will be applied to three mechanism types: channel and slot, ball and socket, and a hinge joint. Each will demonstrate a different type of wear incidence. The mechanisms and their base materials are of direct interest to the end users and infusion points: the Human Landing System (HLS) and the Lunar Surface Innovation Initiative (sustained lunar surface operations). The technology development project is based out of Marshall Space Flight Center, has partnered with Florida International University (Miami, FL) and Plasma Processes (Huntsville, Al), and is supported by a group of NASA mentors from different centers.

dust mitigation↗