Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WHEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2010

Experimental heat and mass transfer of the separated and coupled rotating desiccant wheel and heat wheel

The experimental evaluation of the separated and coupled rotating desiccant wheel and heat wheel is reported. The study aims to investigate the performance of the desiccant wheel and of the heat wheel both when operated separately and jointly. The performance evaluation of the desiccant wheel is based on its moisture removal capacity (MRC), moisture removal regeneration (MRR), and moisture mass balance (MMB). In addition, the study used the total energy balance (TEB), sensible coefficient of performance (COP{sub Sensible}), latent coefficient of performance (COP{sub Latent}) and, total coefficient of performance (COP{sub Total}). The performance of the heat wheel is based on its effectiveness. The COP{sub Sensible}, COP{sub Latent} and, COP{sub Total} are used in the performance evaluation of the coupled desiccant wheel and heat wheel. The general results of the study show that the MRC, MRR and MMB coupled with the TEB, COP{sub Latent}, COP{sub Sensible} and COP{sub Total} predict adequately the performance of the desiccant wheel. In addition, the coupled operation of the desiccant wheel and heat wheel, contributed to the reduction of the external thermal energy requirement for the regeneration of the desiccant wheel. This study can be applied in other researches seeking evaluation of the desiccant wheel, heat wheel, and their combined operation. Moreover, the data presented here are significant for the desiccant wheel benchmarking and for evaluation of the desiccant wheel models. (author)

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2019

On Mechanical Properties of New Railway Wheel Steels for Desert Environments and Sand Caused Wheel Damage Mechanisms

Worn railway wheels after service in the desert were investigated by means of failure analysis, hardness measurements, tensile tests, fracture toughness tests and low-cycle fatigue (LCF) tests. The results complete both previous small-scale laboratory experiments and FEM simulations performed by the authors on widely used steels and new steel grades allowing to better understand the main damage mechanisms due to the sand. These new steel grades were developed for forged-rolled solid wheels in alternative to AAR Class B/C/D steel grades and were designed to ensure high resistance to wear and rolling contact fatigue in the presence of sand, debris or gravel on the rails. This paper covers the in-depth mechanical characterization of wheels made of the new steels. Hardness measurements, tensile tests, fracture toughness tests and LCF tests were carried out. The results are compared with AAR Class B/C/D steels showing an excellent combination of fracture toughness, cyclic yield strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2010

Wheels within Wheels: Hamiltonian Dynamics as a Hierarchy of Action Variables

In systems where one coordinate undergoes periodic oscillation, the net displacement in any other coordinate over a single period is shown to be given by differentiation of the action integral associated with the oscillating coordinate. This result is then used to demonstrate that the action integral acts as a Hamiltonian for slow coordinates providing time is scaled to the 'tick time' of the oscillating coordinate. Numerous examples, including charged particle drifts and relativistic motion, are supplied to illustrate the varied application of these results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

From Atoms to Wheels: The Role of Multi-Scale Modeling in the Future of Transportation Electrification

Traditionally, prototype hardware is built for validation testing to ensure battery systems design changes meet vehicle-level requirements, which is expensive both in cost and time. Virtual engineering (VE) of battery systems for electric vehicle (EV) propulsion offers a reduced-cost alternative to the traditional development process and uses multi-scale modeling to virtually probe the impact of design changes in a particular part on the overall performance of the system. This allows for rapid iteration over multiple design spaces, without committing to build hardware. This perspective article discusses current trends in VE for EV applications and proposes improvements to accelerate EV adoption.

Garrick, Taylor R. (ORCID:0000000322518129)↗
DOE OSTI2012

First-Principles Study of Electronic Structure and Hydrogen Adsorption of 3d Transition Metal Exposed Paddle Wheel Frameworks

Open-site paddle wheels, comprised of two transition metals bridged with four carboxylate ions, have been widely used for constructing metal-organic frameworks with large surface area and high binding energy sites. Using first-principles density functional theory calculations, we have investigated atomic and electronic structures of various 3d transition metal paddle wheels before and after metal exposure and their hydrogen adsorption properties at open metal sites. Notably, the hydrogen adsorption is impeded by covalent metal-metal bonds in early transition metal paddle wheels from Sc to Cr and by the strong ferromagnetic coupling of diatomic Mn and Fe in the paddle wheel configurations. A significantly enhanced H{sub 2} adsorption is predicted in the nonmagnetic Co{sub 2} and Zn{sub 2} paddle wheel with the binding energy of {approx}0.2 eV per H{sub 2}. We also propose the use of two-dimensional Co{sub 2} and Zn{sub 2} paddle wheel frameworks that could have strongly adsorbed dihydrogen up to 1.35 wt % for noncryogenic hydrogen storage applications.

08 HYDROGEN↗
DOE OSTI2025

Advances in Desiccant Wheels for Dehumidification, VOC Mitigation, and CO 2 Removal for Energy-Efficient IAQ Management

Humidity control is pivotal to maintain occupant thermal comfort and suppress mold growth in indoor environments. Furthermore, poor indoor air quality (IAQ) due to the presence of volatile organic compounds (VOCs) and high concentrations (>1,000 ppm) of CO 2 can cause health issues and negatively affect cognitive performance. Therefore, providing high-quality indoor air has gained significant attention over the past decade. Conventional cooling coil and filter-based HVAC systems have limited capability to meet the augmented demand for occupant thermal comfort and high indoor air quality. Moreover, modern buildings are increasingly airtight to save energy, and increasing ventilation to mitigate VOC and CO 2 concentration is discouraged. Separate sensible and latent cooling technology using a rotary desiccant wheel presents a promising solution in this respect. Because of the development of desiccant materials with high water vapor, VOC, and CO 2 uptake, desiccant wheels can be used as an integrated technology option for IAQ management. Here, to promote desiccant wheel use for energy-efficient management of IAQ in buildings, this article reviews recent advancements in using desiccant wheels for dehumidification, VOC mitigation, and CO 2 capture from outdoor air. Finally, the article presents the authors’ perspective by summarizing the key research gaps in the field and discussing the future direction of research to address these gaps from two different aspects, namely, suitable adsorbent material development and desiccant wheel design.

CO2 capture↗
DOE OSTI2016

Effect of wheel speed and annealing temperature on microstructure and texture evolution of Ni{sub 45}Mn{sub 36.6}In{sub 13.4}Co{sub 5} ribbon

Ni{sub 45}Mn{sub 36.6}In{sub 13.4}Co{sub 5} magnetic shape memory alloy was successfully produced as preferentially textured ribbon by melting spinning with different wheel speed. X-ray diffraction (XRD) and electron back scatter diffraction (EBSD) were used to study structure and texture evolution of these melt-spun ribbons. The thickness of melt-spun ribbon is 42 μm, 65 μm and 30 μm depending on wheel speed of 1 0 m/s, 15 m/s and 20 m/s, respectively. Density of α fiber texture (〈100〉//ND) vary with wheel speed changes, and is most intensive in the ribbon with wheel speed of 15 m/s. Grains of the ribbons grow after being annealed at 873 K, 973 K, 1073 K and 1173 K, recrystallization was not observed in ribbons after being annealed at 873 K but occurred in ribbons after being annealed at higher temperatures. The α fiber texture becomes weaker to some extent after annealing at different temperatures, due to new recrystallization texture formed at the process of annealing. - Highlights: •Sectional part of shape memory ribbon is firstly investigated by EBSD method. •Thickness and texture of ribbons vary with wheel speed. •Annealing temperature affect texture and microstructure evolution greatly. •Recrystallization textures were observed in ribbons after being annealed.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Wheel-Walking Propulsion Unit of a Planetary Rover with Active Suspension

The scheme of the propulsion unit with walking mechanism for a wheeled planetary rover is considered. The walking mechanism permits to convert the chassis in a transport position, displacement of rover’s center of mass so as to optimize the load on motor wheels. In wheeled motion the walking mechanism realize function of the active suspension for adaptation of the locomotion system to the surface features. On friable soils where wheeled locomotion is difficult or impossible, wheel-walking mode improves trafficability.

42 ENGINEERING↗
DOE OSTI2022

Robust Wheel Detection for Vehicle Re-Identification

Vehicle re-identification is a demanding and challenging task in automated surveillance systems. The goal of vehicle re-identification is to associate images of the same vehicle to identify re-occurrences of the same vehicle. Robust re-identification of individual vehicles requires reliable and discriminative features extracted from specific parts of the vehicle. In this work, we construct an efficient and robust wheel detector that precisely locates and selects vehicular wheels from vehicle images. The associated hubcap geometry can hence be utilized to extract fundamental signatures from vehicle images and exploit them for vehicle re-identification. Wheels pattern information can yield additional information about vehicles in questions. To that end, we utilized a vehicle imagery dataset that has thousands of side-view vehicle collected under different illumination conditions and elevation angles. The collected dataset was used for training and testing the wheel detector. Experiments show that our approach could detect vehicular wheels accurately for 99.41% of the vehicles in the dataset.

47 OTHER INSTRUMENTATION↗
DOE OSTI2015

Time-resolved spectroscopy using a chopper wheel as a fast shutter

Widely available, small form-factor, fiber-coupled spectrometers typically have a minimum exposure time measured in milliseconds, and thus cannot be used directly for time-resolved measurements at the microsecond level. Spectroscopy at these faster time scales is typically done with an intensified charge coupled device (CCD) system where the image intensifier acts as a “fast” electronic shutter for the slower CCD array. In this paper, we describe simple modifications to a commercially available chopper wheel system to allow it to be used as a “fast” mechanical shutter for gating a fiber-coupled spectrometer to achieve microsecond-scale time-resolved optical measurements of a periodically pulsed light source. With the chopper wheel synchronized to the pulsing of the light source, the time resolution can be set to a small fraction of the pulse period by using a chopper wheel with narrow slots separated by wide spokes. Different methods of synchronizing the chopper wheel and pulsing of the light sources are explored. The capability of the chopper wheel system is illustrated with time-resolved measurements of pulsed plasmas.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2017

Effect of wheel speed on magnetic and mechanical properties of melt spun Fe-6.5 wt.% Si high silicon steel

Here, Fe-Si electric steel is the most widely used soft magnetic material in electric machines and transformers. Increasing the silicon content from 3.2 wt.% to 6.5 wt.% brings about large improvement in the magnetic and electrical properties. However, 6.5 wt.% silicon steel is inherited with brittleness owing to the formation of B2 and D0 3 ordered phase. To obtain ductility in Fe-6.5wt.% silicon steel, the ordered phase has to be bypassed with methods like rapid cooling. In present paper, the effect of cooling rate on magnetic and mechanical properties of Fe-6.5wt.% silicon steel is studied by tuning the wheel speed during melt spinning process. The cooling rate significantly alters the ordering and microstructure, and thus the mechanical and magnetic properties. X-ray diffraction data shows that D0 3 ordering was fully suppressed at high wheel speeds but starts to nucleate at 10m/s and below, which correlates with the increase of Young’s modulus towards low wheel speeds as tested by nanoindentation. The grain sizes of the ribbons on the wheel side decrease with increasing wheel speeds, ranging from ~100 μm at 1m/s to ~8 μm at 30m/s, which lead to changes in coercivity.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Effect of wheel speed on the magnetic and mechanical properties of melt spun Fe-6.5 wt.% electric steel

Fe-Si electric steel is the most widely used soft magnetic materials in electric mahines and motors, transformers and generators. Improving the surperior magnetic and electric properties of 6.5 wt.% high silicon steel is essential for higher may improve energy efficiency and power density of electric machines. However, the brittleness due to the formation of B2 and D03 ordered phases in high silicon steel make it difficult forbids for the application of high silicon steel. It is known that these ordered phases can be fully or partially suppressed by rapid cooling. However, further study is needed to understand the extend of cooling on the magnetic and mechanical properties of 6.5 wt.% silicon steel with various degree of ordering. By tuning the wheel speed from 1m/s to 30m/s with several intervals of the melt spinning process, varying degrees of cooling were achieved on 6.5 wt.% silicon steel ribbons. The cooling rate significant altered the ordering, microstructure size scale, and thus the mechanical and magnetic properties. TEM results showed that D03 ordering can be fully suppressed at high wheel speed, but started to nucleate at 5m/s and below, which correlates with the hardness and Young’s modulus increase towards low wheel speeds as tested by micro and nano indentation. The grain sizes of the ribbons on the wheel side decreased with increasing wheel speeds being ~100 micron at 1m/s and ~8 micron at 30m/s, which led to the change in coercivity. Saturation magnetization and electric resistivity of the ribbons remained about 190 emu/g and 84 microhm *cm, which appeared to be mainly depend on the chemistry.

Fe-6.5%Si Steel↗
DOE OSTI2019

Microstructure and Properties of A356 Alloy Wheels Fabricated by Low-Pressure Die Casting with Local Squeeze

The low-pressure die-casting process (LPDC) is widely used in fabricating aluminum alloy automotive wheels. With good castability and mechanical properties, A356 alloys are important and common materials for LPDC wheels. However, in practical casting process, defects often appear, especially porosities in the wheel thick-walled parts (i.e., spoke) due to inadequate interdendritic feeding, which greatly decreases the mechanical properties. In this investigation, to deal with this problem, local squeeze (LS) was added in conventional LPDC to enhance the interdendritic feeding. The practical A356 alloy wheel castings were fabricated with different LS velocities and times. The quantitative characteristics of α-Al cells, Si particles, and porosities with and without the LS analyzed by optical microscope, scanning electron microscope, and 3D x-ray computed tomography were compared. Their effects on the tensile and impact properties were discussed. The results have shown that the LS can increase the cooling rate and feed shrinkage of spoke parts, hence resulting in finer grains and denser microstructure. In result, the properties of spoke parts were improved with the LS.

36 MATERIALS SCIENCE↗