Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WALL EFFECTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Thick-wall effects in the theory of resistive wall modes

Magnetic interaction of the plasma perturbations with the nearby resistive wall is considered as a resistive wall mode (RWM) problem, but with two essential differences from the traditional thin-wall approach. First, the wall is treated as magnetically thick, which means that the skin depth is not assumed larger than the wall thickness. Second, the plasma is allowed to enter the region where the RWM must be deeply unstable without rotation. The latter corresponds to the plasma operation above the no-wall stability limit demonstrated in the DIII-D tokamak [E. J. Strait et al., Phys. Plasmas 11, 2505 (2004)]. It is shown that the rotational stabilization observed in these experiments can be reproduced in this model if the mode is forced to rotate with a frequency above a critical level. The analytical estimates show that this effect (absent in the model based on the thin-wall approximation) is strong at realistic parameters. The model also predicts that the locking of the rotationally stabilized mode gives rise to instability with a growth rate much larger than its thin-wall estimate.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Theoretical analyses of aerosol aging on a substrate without wall-effects by a cross-flow

Long time ({approx}1 day) aging or reactions of aerosol is typically studied using either large aerosol chambers (> 10 m3) or particles supported on a substrate to minimize wall effects. To avoid wall effects in the latter, it is often essential that the wall reactivity be extremely small (<< 10-5 reactions per encounter) and that the particle loadings be very small (< 1 pg/cm2) to eliminate transport-limited trace gas depletion near the particles and substrate. We evaluate here a cross-flow approach, which greatly reduces these constraints. Particles are to be supported on a micromesh ({approx}50% or more open area) through which the reactive gas is drawn at around a few hundred cm/s. The analysis shows how the competitions between flow and diffusion establishes a 'zone of isolation' several microns wide around each reactive particle, outside of which the reactivity of other particles or the substrate are irrelevant to the local reactions. This cross-flow approach reduces the effects of substrate and collective particle reactivity typically orders of magnitude, and will facilitate aging studies of supported aerosols.

54 ENVIRONMENTAL SCIENCES↗

Boron-10 Lined Proportional Counter Wall Effects

The Department of Energy Office of Nuclear Safeguards (NA-241) is supporting the project 'Coincidence Counting With Boron-Based Alternative Neutron Detection Technology' at Pacific Northwest National Laboratory (PNNL) for development of an alternative neutron coincidence counter. The goal of this project is to design, build and demonstrate a boron-lined proportional tube based system in the configuration of a coincidence counter. This report provides information about how variations in proportional counter radius and gas pressure in a typical coincident counter design might affect the observed signal from boron-lined tubes. A discussion comparing tubes to parallel plate counters is also included.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Reactor wall effects in Si–Cl 2 –Ar atomic layer etching

This work complements our previous manuscript [J. Vac. Sci. Technol. A41, 062602 (2023)] where predictions from molecular dynamics (MD) simulations of silicon–chlorine–argon (Si–Cl 2 –Ar) atomic layer etching (ALE) are compared to experiments. When etch product distributions for atomic chlorine (Cl) and silicon chlorides were initially compared to optical emission spectroscopy (OES) signals, it appeared that there was a discrepancy between the MD predictions and experimental results at higher ion fluences. Experiments showed a relatively long period of nearly constant Cl-containing etch products released from the ion-bombarded surface (referred to as the “plateau”) but this effect was not observed in MD simulations. In this report, we demonstrate that the “plateau” observed in the OES signals is most likely due to the desorption of Cl-containing etch products from the walls of the reactor and subsequent adsorption on the Si substrate. Experiments varying the gas residence time in the chamber while keeping incoming gas concentrations and pressure constant support this interpretation. We also conducted experiments with an additional Ar-only flow in the chamber to reduce the concentration of Cl-containing species on the chamber walls. For both sets of flow modification experiments, we observe results consistent with the hypothesis that Cl-containing species desorbing from chamber walls are a significant cause of the observed discrepancy between MD predictions and experimental observations. If the measured OES signals are corrected for this “additional” source of Cl-containing species at the surface, the MD predictions and measured OES signals are in excellent agreement. This further supports the predictive capability of MD simulations to accurately capture the relevant physical and chemical processes in plasma-assisted ALE processes. We provide an order of magnitude estimate of the required density of Cl-containing species that would account for the additional etch products observed. Finally, we discuss the implications of this effect on ALE in plasma nanofabrication.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Advanced Insulation for High Performance Cost-Effective Wall, Roof, and Foundation Systems Final Report

The objective of this project was to explore and potentially develop high performing insulation with increased R/inch and low impact on climate change that would help design highly insulating building envelope systems with more durable performance and lower overall system cost than envelopes with equivalent performance made with materials available today. The proposed technical approach relied on insulation foams with nanoscale pores (about 100 nm in size) in which heat transfer will be decreased. Through the development of new foaming methods, of new polymer formulations and new analytical techniques, and by advancing the understanding of how cells nucleate, expand and stabilize at the nanoscale, Dow successfully invented and developed methods to produce foams with 100 nm cells and 80% porosity by batch foaming at the laboratory scale. Measurements of the gas conductivity on small nanofoam specimen confirmed quantitatively the benefit of nanoscale cells (Knudsen effect) to increase insulation value, which was the key technical hypotheses of the program. In order to bring this technology closer to a viable semi-continuous/continuous process, the project team modified an existing continuous extrusion foaming process as well as designed and built a custom system to produce 6" x 6" foam panels. Dow demonstrated for the first time that nanofoams can be produced in a both processes. However, due to technical delays, foam characteristics achieved so far fall short of the 100 nm target set for optimal insulation foams. In parallel with the technology development, effort was directed to the determination of most promising applications for nanocellular insulation foam. Voice of Customer (VOC) exercise confirmed that demand for high-R value product will rise due to building code increased requirements in the near future, but that acceptance for novel products by building industry may be slow. Partnerships with green builders, initial launches in smaller markets (e.g. EIFS), and efforts to drive cost down will help acceptance in residential and commercial retrofit and new construction.

36 MATERIALS SCIENCE↗

Effects of wall electrodes on Hall effect thruster plasma

This paper investigates the physical mechanisms that cause beneficial and detrimental performance effect observed to date in Hall effect thrusters with wall electrodes. It is determined that the wall electrode sheath can reduce ion losses to the wall if positioned near the anode (outside the dense region of the plasma) such that an ion-repelling sheath is able to form. The ability of the wall electrode to form an ion-repelling sheath is inversely proportional to the current drawn—if the wall electrode becomes the dominant sink for the thruster discharge current, increases in wall electrode bias result in increased local plasma potential rather than an ion-repelling sheath. A single-fluid electron flow model gives results that mimic the observed potential structures and the current-sharing fractions between the anode and wall electrodes, showing that potential gradients in the presheath and bulk plasma come at the expense of current draw to the wall electrodes. Secondary electron emission from the wall electrodes (or lack thereof) is inferred to have a larger effect if the electrodes are positioned near the exit plane than if positioned near the anode, due to the difference in energy deposition from the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of wall thickness on the flow instability of supercritical pressure water in a tube - 18568

The subcritical steam generators in the current high-temperature-reactor pebble-bed module, HTR-PM, in China can be replaced by supercritical steam generators to better coordinate the reactors and the supercritical steam turbines to improve thermal efficiencies with no phase change at supercritical pressures. This study numerically studied the heat transfer and flow instability of supercritical pressure water in a vertical tube with zero- and finite-thickness walls. The effect of the wall thickness on the heat transfer of supercritical pressure water at steady state was negligible. In the transient calculations, the fluid flow rate oscillated intensely beyond a certain heat flux with zero-thickness wall, while the flows in the tube with the finite-thickness walls acted totally different. The wall properties including the density and specific heat were varied to analyze why the oscillations were suppressed when the finite-thickness wall was considered in the calculation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Influence of Axial Power Distributions on Rod-to-wall Gap

In a scaled-down (3 x 3, 4 x 4, 5 x 5 or 6 x 6) rod bundle thermal hydraulic experiment, channel walls were often applied to surround the experimental rod bundle and provide a hydraulic flow boundary for the experiments. However, in the actual PWR (Pressurized Water Reactor), there are no walls surrounding the rod bundle fuel assembly. These non-representative walls can lead to non-prototypical conditions in the rod bundle experiments. There are several researches about the wall effects in rod bundle experiments. Based on hydraulic consideration, Zang developed a wall effect factor by subchannel analysis method to investigate the wall effects of different scale rod bundles. He did not pay attention to the wall effects in thermal aspects. Li studied the wall effects of different scale rod bundles of tight arrangement spiral-fin fuel assembly by CFD. The existing researches mostly focus on the wall effects of different scale rod bundles. There are very few, if any at all, studies focus on how to avoid or minimize wall effects through proper experimental design by adjusting the rod-to-wall gap (the gap between the channel wall and outer rod wall) for rod bundles of various scales. In addition, the axial power distribution is different in different periods of the life cycle in the PWR core. For example, it usually is outlet peak power distribution in the axial direction at the beginning of life span. However, it may turn to the inlet peak power distribution when the control rods are pulled out from the high burn up of fuel in the reactor core. Both flow dynamics and heat transfer mechanism change depending on various axial power distributions. Subsequently, it is important to study the impacts of the wall effects on flow and heat transfer with different axial power distributions in rod bundle experiments. That is, in the evaluation of rod-to-wall gap in rod bundle experiments, the influence of axial power distributions should be examined. In this paper, the rod-to-wall gap was calculated in axially uniform and non-uniform power, including inlet peak, cosine, and exit peak heat flux distributions. The rod-to-wall gap calculation results were then compared with respect to two different criterion: the average fluid temperature and the maximum wall temperature criterion, to study the influence of axial heat flux profile on radial thermal distribution.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Effect of Collisionality on Kinetic Stability of the Resistive Wall Mode

The impact of collisionless, energy-independent, and energy-dependent collisionality models on the kinetic stability of the resistive wall mode is examined for high pressure plasmas in the National Spherical Torus Experiment. Future devices will have decreased collisionality, which previous stability models predict to be universally destabilizing. In contrast, in kinetic theory reduced ion-ion collisions are shown to lead to a significant stability increase when the plasma rotation frequency is in a stabilizing resonance with the ion precession drift frequency. When the plasma is in a reduced stability state with rotation in between resonances, collisionality will have little effect on stability.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Numerical study of the plasma wall-bias effect on the ion flux through acceleration grid hole

In the extraction of ion beams from a source plasma through a grid acceleration structure, one of the key improvement issues is the fluence of the ion flux. Theoretical research has usually been focused on the structure of the grid system and the distribution of the electrostatic voltages over the grid layers. In the present work, using a self-consistent computer simulation between the plasma source, sheath potential, and the grid system, the effect of the source-wall biasing on the fluence of the ion flux through a three-grid acceleration system has been examined. It is found that a strongly positive wall-biasing can significantly enhance the ion flux by improving the shape of the plasma sheath potential meniscus at the entrance to the grid hole structure.

43 PARTICLE ACCELERATORS↗

Numerical Investigation of Wall-Cooling Effect on Aero-Optical Distortions for Hypersonic Boundary Layer

Compressible wall-modeled large-eddy simulations of Mach 8 turbulent boundary-layer flows over a flat plate were carried out for the conditions of the hypersonic wind tunnel at Sandia National Laboratories. The simulations provide new insight into the effect of wall cooling on the aero-optical path distortions for hypersonic turbulent boundary-layer flows. Four different wall-to-recovery temperature ratios, 0.3, 0.48, 0.71, and 0.89, are considered. Despite the much lower grid resolution, the mean velocity, temperature, and resolved Reynolds stress profiles from the simulation for a temperature ratio of 0.48 are in good agreement with those from a reference direct numerical simulation. The normalized root-mean-square optical path difference obtained from the present simulations is compared with that from reference direct numerical simulations, Sandia experiments, as well as predictions obtained with a semi-analytical model by Notre Dame University. Here the present analysis focuses on the effect of wall cooling on the wall-normal density correlations, on key underlying assumptions of the aforementioned model such as the strong Reynolds analogy, and on the elevation angle effect on the optical path difference. Wall cooling is found to increase the velocity fluctuations and decrease the density fluctuations, resulting in an overall reduction of the normalized optical path distortion. Compared to the simulations, the basic strong Reynolds analogy overpredicts the temperature fluctuations for cooled walls. Also different from the strong Reynolds analogy, the velocity and temperature fluctuations are not perfectly anticorrelated. Finally, as the wall temperature is raised, the density correlation length, away from the wall but inside the boundary layer, increases significantly for beam paths tilted in the downstream direction.

42 ENGINEERING↗

Uniform field in microwave cavities through the use of effective magnetic walls

Wire medium (WM) resonators have emerged as a promising realization for plasma haloscopes—devices designed to detect axions, a potential component of dark matter. Key factors influencing the detection probability include cavity volume, resonance quality factor, and form factor. While the form factor has been explored for resonant frequency tuning, its optimization for axion detection remains unexplored. Here, in this work, we present an approach to significantly enhancing the form factor of WM plasma haloscopes. By shifting the metal walls of the resonator by a quarter wavelength, we effectively convert an electric wall boundary condition into a magnetic wall one, allowing for an almost uniform mode. Theoretical analysis and numerical simulations confirm that this modification improves the electric field profile and boosts the form factor, while also slightly enhancing the quality factor. We validate these findings through experimental results from two prototype resonators: one with a standard geometry and another with a quarter-wave air gap between the WM and the walls. Additionally, our method provides a simple way to control the field profile within WM cavities, which can be explored for further applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Creating high-precision reference gas standards of 85Kr for groundwater age-dating

Absolute gas counting (AGC) was applied to two gas blends of 85Kr in argon-methane (P10) counting gas to establish a high-precision specific activity (Bq/cm3) reference value for characterizing 85Kr detection efficiency for groundwater age dating measurements. The AGC or length-compensated technique has been utilized by the metrology community for decades and is an accepted method for developing radioactive gas standards. The AGC capability at Pacific Northwest National Laboratory (PNNL) uses a set of nine unequal-length proportional counters with precisely-measured internal volumes, and a gas loading system with high-precision pressure and temperature sensors. A series of AGC measurements were collected at multiple pressures to determine the inverse pressure relationship (1/P) for 85Kr and define a wall-effect correction that accounts for events decaying into the detector wall and not depositing sufficient energy in the gas to be detected. In addition to the wall-effect, two additional corrections were evaluated and are discussed in detail. Specifically, the threshold effect which accounts for events deposited below the analysis threshold and a detection efficiency as a function of detector volume effect that was observed during analysis. A robust uncertainty model was developed using the Guide to the expression of Uncertainty in Measurements (GUM) approach. The combination of carefully scrutinized correction factors, precise measurements of pressure, temperature and detector volume, and robust counting statistics resulted in the determination of high-precision specific activity values with 0.50% or less total combined uncertainty for two Kr-in-P10 reference gas standards (KP10) that will enable new groundwater age-dating measurements at PNNL.

Kr-85↗

Sintering of Iron Ores in a Millipot in Comparison with Tablet Testing and Industrial Process

To explore the feasibility of small-scale sintering pot testing, a ‘millipot’ facility (diameter of 53 mm and height of 400 mm) was established and used to examine the sintering performance of iron ores and other non-traditional ferrous materials. The sintering performance of a millipot was examined across a range of different operational conditions (coke rate and suction pressure) and compared with an industrial sinter strand operation. Tablet tests were also performed to assist in the design of the millipot experiments and identify conditions for achieving mineral composition similar to the industrial sinter. For the millipot experiments, the materials used need to be compacted to increase the bulk density, and a higher coke rate is required to compensate the high heat loss caused by wall effects. A higher suction pressure is also necessary to maintain an oxidizing atmosphere in the sinter bed. As expected, it was not possible to eliminate the wall effect, which resulted in more primary hematite at edges of the sintered column. However, the sintered material from the center of column simulates industrial sinter reasonably well. As such, millipot provides a practical way to evaluate the sintering process and material performance at laboratory scale, helping to bridge the gap between tablet sintering and large scale pot sintering, or full scale plant trial. The results of millipot testing can be used for designing larger scale experiments or commercial sintering trials.

36 MATERIALS SCIENCE↗

Effects of gas–wall interactions on measurements of semivolatile compounds and small polar molecules

Recent work has quantified the delay times in measurements of volatile organic compounds (VOCs) caused by the partitioning between the gas phase and the surfaces of the inlet tubing and instrument itself. In this study we quantify wall partitioning effects on time responses and transmission of multifunctional, semivolatile, and intermediate-volatility organic compounds (S/IVOCs) with saturation concentrations ( C * ) between 10 0 and 10 4 µg m -3 . The instrument delays of several chemical ionization mass spectrometer (CIMS) instruments increase with decreasing C * , ranging from seconds to tens of minutes, except for the NO 3 - CIMS where it is always on the order of seconds. Six different tubing materials were tested. Teflon, including PFA, FEP, and conductive PFA, performs better than metals and Nafion in terms of both delay time and transmission efficiency. Analogous to instrument responses, tubing delays increase as C * decreases, from less than a minute to >100 min . The delays caused by Teflon tubing vs. C * can be modeled using the simple chromatography model of Pagonis et al. (2017). The model can be used to estimate the equivalent absorbing mass concentration ( C w ) of each material, and to estimate delays under different flow rates and tubing dimensions. We also include time delay measurements from a series of small polar organic and inorganic analytes in PFA tubing measured by CIMS. Small polar molecules behave differently than larger organic ones, with their delays being predicted by their Henry's law constants instead of their C * , suggesting the dominance of partitioning to small amounts of water on sampling surfaces as a result of their polarity and acidity properties. PFA tubing has the best performance for gas-only sampling, while conductive PFA appears very promising for sampling S/IVOCs and particles simultaneously. The observed delays and low transmission both affect the quality of gas quantification, especially when no direct calibration is available. Improvements in sampling and instrument response are needed for fast atmospheric measurements of a wide range of S/IVOCs (e.g., by aircraft or for eddy covariance). These methods and results are also useful for more general characterization of surface–gas interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An extended variational method for the resistive wall mode in toroidal plasma confinement devices

The external-kink stability of a toroidal plasma surrounded by a rigid resistive wall is investigated. The well-known analysis of Haney and Freidberg is rigorously extended to allow for a wall that is sufficiently thick that the thin-shell approximation does not necessarily hold. A generalized Haney–Freidberg formula for the growth-rate of the resistive wall mode is obtained. Thick-wall effects do not change the marginal stability point of the mode but introduce an interesting asymmetry between growing and decaying modes. Growing modes have growth-rates that exceed those predicted by the original Haney–Freidberg formula. On the other hand, decaying modes have decay-rates that are less than those predicted by the original formula. The well-known Hu–Betti formula for the rotational stabilization of the resistive wall mode is also generalized to take thick-wall effects into account. Increasing wall thickness facilitates the rotational stabilization of the mode, because it decreases the critical toroidal electromagnetic torque that the wall must exert on the plasma. On the other hand, the real frequency of the mode at the marginal stability point increases with increasing wall thickness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation of particle and vapor wall-loss effects on controlled wood-smoke smog-chamber experiments

Here, smog chambers are extensively used to study processes that drive gas and particle evolution in the atmosphere. A limitation of these experiments is that particles and gas-phase species may be lost to chamber walls on shorter timescales than the timescales of the atmospheric processes being studied in the chamber experiments. These particle and vapor wall losses have been investigated in recent studies of secondary organic aerosol (SOA) formation, but they have not been systematically investigated in experiments of primary emissions from combustion. The semi-volatile nature of combustion emissions (e.g. from wood smoke) may complicate the behavior of particle and vapor wall deposition in the chamber over the course of the experiments due to the competition between gas/particle and gas/wall partitioning. Losses of vapors to the walls may impact particle evaporation in these experiments, and potential precursors for SOA formation from combustion may be lost to the walls, causing underestimations of aerosol yields. Here, we conduct simulations to determine how particle and gas-phase wall losses contributed to the observed evolution of the aerosol during experiments in the third Fire Lab At Missoula Experiment (FLAME III). We use the TwO-Moment Aerosol Sectional (TOMAS) microphysics algorithm coupled with the organic volatility basis set (VBS) and wall-loss formulations to examine the predicted extent of particle and vapor wall losses. We limit the scope of our study to the dark periods in the chamber before photo-oxidation to simplify the aerosol system for this initial study. Our model simulations suggest that over one-third of the initial particle-phase organic mass (41 %) was lost during the experiments, and over half of this particle-organic mass loss was from direct particle wall loss (65 % of the loss) with the remainder from evaporation of the particles driven by vapor losses to the walls (35 % of the loss). We perform a series of sensitivity tests to understand uncertainties in our simulations. Uncertainty in the initial wood-smoke volatility distribution contributes 18 % uncertainty to the final particle-organic mass remaining in the chamber (relative to base-assumption simulation). We show that the total mass loss may depend on the effective saturation concentration of vapor with respect to the walls as these values currently vary widely in the literature. The details of smoke dilution during the filling of smog chambers may influence the mass loss to the walls, and a dilution of ~ 25:1 during the experiments increased particle-organic mass loss by 33 % compared to a simulation where we assume the particles and vapors are initially in equilibrium in the chamber. Finally, we discuss how our findings may influence interpretations of emission factors and SOA production in wood-smoke smog-chamber experiments.

54 ENVIRONMENTAL SCIENCES↗