SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Controlling the morphology of organic solar cells (OSCs) presents a significant challenge due to their complex structure and composition.
Solution processability of polymer semiconductors becomes an unfavorable factor during the fabrication of pixelated films since the underlying layer is vulnerable to subsequent solvent exposure. A foundry-compatible patterning process must meet requirements including high-throughput and high-resolution patternability, broad generality, ambient processability, environmentally benign solvents, and, minimal device performance degradation. However, known methodologies can only meet very few of these requirements. Here, a facile photolithographic approach is demonstrated for foundry-compatible high-resolution patterning of known p- and n-type semiconducting polymers. This process involves crosslinking a vertically phase-separated blend of the semiconducting polymer and a UV photocurable additive, and enables ambient processable photopatterning at resolutions as high as 0.5 μm in only three steps with environmentally benign solvents. The patterned semiconducting films can be integrated into thin-film transistors having excellent transport characteristics, low off-currents, and high thermal (up to 175 °C) and chemical (24 h immersion in chloroform) stability. Moreover, these patterned organic structures can also be integrated on 1.5 μm-thick parylene substrates to yield highly flexible (1 mm radius) and mechanically robust (5,000 bending cycles) thin-film transistors.
The fabrication of organic solar cells (OSCs) by a layer-by-layer (LBL) method has attracted growing attention in recent years. As already known, the pre-aggregates of conjugated polymers in solution have a profound impact on their microstructure morphology in films. Herein, by simply controlling the solution temperature and annealing processes, the pre-aggregation behavior of D18 polymer in solution can be fine-tuned and the microstructure of D18 bottom layer is well manipulated. The optimized D18 bottom layer can effectively regulate L8-BO upper-layer-forming suitable networks for efficient charge transportation. In addition, a vertical phase separation with a special D/D:A/A structure (P-i-N-type component distribution) is also formed. As a result, compared to the 16.43% power conversion efficiency (PCE) of the bulk heterojunction devices, such control enables bilayer OSC devices based on the polymer D18 and L8-BO to deliver an enhanced PCE of 18.02% with simultaneously improved short-circuit current density, open-circuit voltage, and fill factor. Importantly, it is also demonstrated in these results that the LBL deposition process utilizing the pre-aggregation of polymer and its fiber-network-forming ability is a very promising approach to improve charge dynamics, suppress carrier recombination, and fabricate highly efficient OSCs.
Explore the source record for details and available documents.
We report how to improve charge transport properties and reduce energy losses are the two main challenges of organic solar cells (OSCs). Herein, a new device fabrication strategy that combines the layer-by-layer (LBL) method and a quaternary active layer is demonstrated to realize highly efficient photovoltaic performance of the OSCs based on PM6:PM7/Y6:O1-2F. The introduction of the second donor, PM7,forms a cascade energy-level alignment with PM6 that facilitates effective charge transfer. The second acceptor, O1-2F, which is poorly miscible with the donors, helps to reduce the miscibility between the donors and acceptors, and thus delivers a more desirable vertical phase separation of the active layer. Furthermore, the alloy acceptor of O1-2F and Y6 can optimize the horizontal and vertical morphology of the active layer, forming an effective charge separation and continuous charge transport channel. As a result, the PM6:PM7/Y6:O1-2F system shows a distinct increase in charge mobility and a reduced nonradiative lossΔVnrof 0.231 V compared to the PM6/Y6 system, achieving a high-power conversion efficiency of18.23%. The results indicate that the quaternary LBL OSCs are promising for future large-scale and industrial manufacture of the OSCs.
The performance of all‐polymer solar cells is often enhanced by incorporating solvent additives during solution processing. Here, in particular, blends based on the model all‐polymer system PBDBT:N2200 have been shown to have increased short‐circuit current and fill factor when processed with dilute diiodooctane (DIO). However, the morphological mechanism that drives the increase in performance is often not well understood due to limitations in common characterization techniques. In this study, it is shown that a combination of X‐ray techniques with cryogenic high‐resolution transmission electron microscopy (HRTEM) analysis can provide a quantitative and spatially resolved picture of polymer chain orientation and alignment in all‐polymer blends. It is found that DIO induces vertical phase separation in PBDBT‐2F:F‐N2200 and increases donor crystallite thickness in the pi‐stacking direction leading to an acceptor‐rich film surface. However, it is also shown that DIO does not disrupt the formation of face‐on donor–acceptor interfaces. These findings suggest that dilute DIO primarily affects crystalline domain formation in single component regions as opposed to mixed regions; thus, dilute DIO can impact vertical charge transport pathways without sacrificing donor–acceptor interfacial connectivity.
Sequential deposition has great potential to achieve high performance in organic solar cells due to the resulting well-controlled vertical phase separation. In this work, double bulk heterojunction organic solar cells are fabricated by sequential-blade cast in ambient conditions. Probed by the in situ grazing incidence X-ray diffraction and in situ UV–vis absorption measurements, the seq-blade system exhibits a different tendency from each of the binary films during the film formation process. Due to the extensive aggregation of FOIC, the binary PBDB-T:FOIC film displays a strong and large phase separation, resulting in low current density (J sc) and unsatisfactory power conversion efficiency. In the seq-blade cast system, the bottom layer PBDB-T:IT-M produces many crystal nuclei for the top layer PBDB-T:FOIC, so the PBDB-T molecules are able to crystallize easily and quickly. Balanced crystallization kinetics between polymer and small molecule and an ideal percolation network in the film are observed. In addition, the balanced crystallization kinetics are favorable toward realizing lower recombination loss through charge transport processes.
Forming an ideal bulk heterojunction (BHJ) morphology is a critical issue governing the photon to electron process in organic solar cells (OSCs). Complementary to the widely-used blend casting (BC) method for BHJ construction, sequential casting (SC) can also enable similar or even better morphology and device performance for OSCs. Here, BC and SC methods on three representative donor:acceptor (D:A) blends are utilized, that is, PM6:PC 71 BM, PM6:IT-4F and PM6:L8-BO. Higher power conversion efficiencies (PCEs) in all cases by taking advantage of beneficial morphology from SC processing are achieved, and a champion PCE of 18.86% (certified as 18.44%) based on the PM6:L8-BO blend is reached, representing the record value among binary OSCs. The observations on phase separation and vertical distribution inspire the proposal of the swelling–intercalation phase-separation model to interpret the morphology evolution during SC processing. Further, the vertical phase segregation is found to deliver an improvement of device performance via affecting the charge transport and collection processes, as evidenced by the D:A-ratio-dependent photovoltaic properties. Besides, OSCs based on SC processing show advantages on device photostability and upscale fabrication. Finally, this work demonstrates the versatility and efficacy of the SC method for BHJ-based OSCs.
The molecular conformation of giant molecule acceptors (GMAs) plays a significant role in regulating the intermolecular interactions and their photovoltaic performances in organic solar cells (OSCs). For the linear GMA GT‐l, the stronger homo‐molecular interaction causes its aggregation being weakly affected by the donor, thus forming an ordered molecular stacking and proper phase separation in its blend film. The star‐shaped GMA GT‐s‐based blend film shows a dominant hetero‐molecular interaction that suppresses the aggregation of the donor and acceptor, resulting in smaller phase separation and more uniform vertical phase distribution. While for another star‐shaped GMA GTs, the weakest hetero‐molecular interaction causes its blend film to form larger phase separation. Therefore, the GT‐l based OSC with PM6 as donor shows the highest charge mobilities, the fastest charge transfer (CT) process, reduced energy loss and less charge recombination, contributing to a higher power conversion efficiency (PCE) of 19.03%. Comparatively, the PCEs of the OSCs based on GTs and GT‐s are 18.05% and 17.58% respectively. Notably, all the three GMAs based OSCs show excellent thermal stability and long‐term storage stability. This study provides a facile strategy by tuning the linking unit and its connecting mode for designing highly efficient and stable organic photovoltaic materials.
Constructing tandem and multi-blend organic solar cells (OSCs) is an effective way to overcome the absorption limitations of conventional single-junction devices. However, these methods inevitably require tedious multilayer deposition or complicated morphology-optimization procedures. Herein, sequential deposition is utilized as an effective and simple method to fabricate multicomponent OSCs with a double-bulk heterojunction (BHJ) structure of the active layer to further improve photovoltaic performance. Two efficient donor-acceptor pairs, D18-Cl:BTP-eC9 and PM6:L8-BO, are sequentially deposited to form the D18-Cl:BTP-eC9/PM6:L8-BO double-BHJ active layer. In these double-BHJ OSCs, light absorption is significantly improved, and optimal morphology is also retained without requiring a more complicated morphology optimization involved in quaternary blends. Compared to the quaternary blend devices, energy loss (E loss ) is also reduced by rationally matching each donor with an appropriate acceptor. Consequently, the power conversion efficiency (PCE) is improved from 18.25% for D18-Cl:BTP-eC9 and 18.69% for PM6:L8-BO based binary blend OSCs to 19.61% for the double-BHJ OSCs. In contrast, a D18-Cl:PM6:L8-BO:BTP-eC9 quaternary blend of OSCs exhibited a dramatically reduced PCE of 15.83%. Finally, these results demonstrate that a double-BHJ strategy, with a relatively simple processing procedure, can potentially enhance the device performance of OSCs and lead to more widespread use.
Mechanically durable organic solar cells (OSCs) with high efficiency are deemed as the ideal candidate for the power source of the next generation wearable electronic devices. However, the brittle nature of small molecules in most high-efficiency OSCs consisting of polymer and small molecule encourages easy formation of cracks in the photoactive film under deformation. Here, the vertical composition distribution of the active layer has been well optimized through sequential blade coating to realize highly deformable while efficient OSC. The optimized morphology exhibits distinct donor-rich and homogenous region distributed along the vertical direction in the bulk. The donor-rich region provides sufficient chain entanglements and strong interfaces beneficial for mechanical robustness of film, while homogeneously mixed region offers continuous interpenetrating network to maintain high device through-put, resulting in superior efficiency of 14.4% with high crack-onset strain (COS) of 30.5%. This efficiency versus COS combination is much higher than the best combination reported in all polymer systems (COS of 15.9% and efficiency of 11.1%). To the best of our knowledge, it is the highest COS value achieved in polymer-small molecule systems. As a result, the rational control over vertical stratification demonstrated here would guide researchers in the development of innovative wearable electronics.
All-polymer solar cells (all-PSCs) and all-polymer photodetectors (all-PPDs) are promising for application in flexible electronics, but their performance is greatly limited by the lack of polymer acceptors and the difficulties in morphology control. Herein, we report the use of a high-mobility n-type polymer semiconductor, PNDI-DTBT, for fabricating high-performance all-PSCs and all-PPDs. By pairing PNDI-DTBT with a matched polymer donor, a prominent power conversion efficiency of 8.5% was obtained in all-PSCs, demonstrating the great potential of high-mobility n-type polymers with a conventional donor–acceptor skeleton for photovoltaic application. Moreover, all-PPDs with a low dark current density of 1.32 × 10 –8 A cm –2 at –0.1 V bias and a high specific detectivity of 4.77 × 10 12 Jones were achieved, which belong to the best results of organic photodetectors. Morphology investigations revealed that the formation of a bicontinuous interpenetrating network with optimal phase separation scale, high domain purity, and preferential vertical composition distribution in the bulk-heterojunction active layer contribute to the remarkable device performance. Furthermore, these results suggest that combining high-mobility n-type polymers and morphology optimization is fruitful to achieving high-performance all-PSCs and all-PPDs.
Organic solar cells (OSC) feature a hierarchical structure with the electron donor/acceptor layer sandwiched by anode and cathode, which raises the importance of controlling the molecular crystal orientation, domain size, and vertical distribution to facilitate the charge collection at electrodes. However, the similar conjugated backbone of donor/acceptor material and fast film–formation kinetics have led to spinodal–decomposition–orientated phase separation that result in the film presenting an intimately mixed morphology and random molecular orientation. To solve the issue, the mixing Gibbs free energy–triggered solid–liquid phase separation during the film formation process is enhanced by solidifying one component and solvating the other based on a liquid additive. Following the liquid evaporation process, a favorable vertical distribution is obtained. Meanwhile, the prolonged solvation process enlarges the domain size and assists the molecules to diffuse and orient properly, enabling better exciton/charge dynamics during the power conversion processes. As a result, the fabricated devices exhibit a fill factor over 80% and an efficiency of 18.72%, which is one of the top efficiencies for binary OSCs. In conclusion, insights and a methodology is provided here to manipulate the organic donor/acceptor phase separation in terms of mixing Gibbs free energy.
Liquid-phase turbulence plays a vital role in determining various gas-liquid two-phase flow parameters, such as void fraction distribution, bubble morphology, bubble-bubble interactions, and interfacial area concentration. In this study, a two-phase flow database including both the gas- and liquid-phases measurements was developed focusing on three bubbly flow conditions in an air-water two-phase flow loop with a vertical one-inch diameter circular pipe test section. A particle image velocimetry (PIV) system integrating an optical phase separation method, i.e., the planar laser-induced fluorescence (PLIF) technique using fluorescent particles and optical filtration, was applied to measure the liquid-phase turbulence information, including the time-averaged velocity, Reynolds stress, and turbulent kinetic energy for the liquid phase. The PIV measurements were taken at three ports along the test section at 14.5, 51.5, and 88.5 pipe inner diameters downstream of a bubble injector. In addition, a double-sensor conductivity probe was used to measure radial distributions of the local time-averaged void fraction and gas velocity. The measured liquid-phase turbulence was used to benchmark Sato's turbulence model considering the bubble-induced shear stress for the three tested bubbly flows. The benchmark results showed good agreement between the PIV measurements and model predictions. Lastly, in the two bubbly flows tested that have low void fractions being less than 3%, the effect of the bubble-induced turbulence was found not significant. However, the bubble-induced shear stress becomes important with the increase of the void fraction.
Abstract Obtaining a well‐accurate vertical distribution active layer morphology through the air‐printing process is an essential task for achieving efficient scalable large‐area organic solar cells (OSCs). In this target, the desired and controllable pseudo planar heterojunction (PPHJ) active layer structure with suitable phase separation is developed by pre‐deposited D18‐Cl layer under the PM6:BTP‐eC9 film via an eco‐friendly manufacturing method. The addition of the D18‐Cl regulates molecular crystallization and leads to an ideal vertical stratification while simultaneously suppressing voltage loss, optimizing energetic disorder, and carrier management. Impressively, the optimal PPHJ devices perform superior power conversion efficiencies (PCEs) of 19.05% (100 nm), 17.33% (300 nm), and 14.14% (4 cm 2 ) compared to the BHJ devices. Importantly, the PPHJ OSCs also exhibit an impressive extrapolated T 80 (the time required to reach 80% of initial PCE) of long‐time storage and operational stability, as well as thermal stability.
Our growing computing needs, especially in applications that heavily rely on artificial intelligence (AI), motivate a search for new components that could substantially augment the performance of general-purpose digital computers. Beyond ON/OFF switching, new components with linear multistate analog resistive tuning, nonlinear volatile switching, spiking, oscillatory, stochastic and other complex functionalities could enable highly efficient neuromorphic computing schemes for AI information processing. Compared to the extreme multifunctionality of biological neurons, realizing all the above characteristics in a single, scalable analog component remains a grand challenge. Here we investigate electrochemical gating combined with localized thermal activation to program and switch a single, vertically integrated and dimensionally scaled electrothermal chemical random access memory (ETCRAM) with a channel and reservoir composed of phase-separated vanadium oxide. Closely related to electrochemical RAM (ECRAM), ETCRAM uses an integrated gate-heater electrode to overcome kinetic barriers that help retain states at ambient temperatures. In addition to synapse-like stable and programmable analog resistance states arising from redox-tunable phase coexistence, a single component exhibits neuron-like nonlinear conductance switching with a tunable threshold and self-driven dynamics owing to the thermally driven metal-insulator phase transition in vanadium dioxide. More broadly, we demonstrate that electrochemically stabilized phase coexistence could unlock analog electronics with novel functionality, stability, reconfigurability, and scalability.
Efficient photovoltaic cells based on thin films of solution-processed 2D Ruddlesden–Popper hybrid perovskites (RPPs) represent an exciting breakthrough due to their enhanced tunability and chemical stability relative to those fabricated from 3D phases. However, reports of efficient charge separation and current collection are in apparent contradiction with the well-known enhancement of the exciton binding energy in multilayered halide perovskites, which should lower the device’s internal quantum efficiency and voltage. This controversy has led to various proposals for the electronic and physical structure of RPP thin films, including phase inhomogeneity as the driving force for exciton dissociation and transport. We address this apparent paradox in high-quality hot-cast RPP films by correlating ultrafast transient absorption spectroscopy with X-ray scattering measurements. We show that a hot-casting fabrication method produces highly phase pure n = 3 (BA) 2 (MA) n-1 Pb n I 3n+1 RPP structures. The high-phase purity and large grain sizes allow us to observe vertical transport of excitons via a diffusive process and allow us to determine that charge separation is primarily driven by dissociation at surface localized subgap electronic states. Furthermore, we analyze the differential absorption kinetics in films of varying thickness to directly determine that the excitonic diffusion constant is ~0.18 cm 2 s –1 . We propose that a surface localized structural distortion, observed using surface selective grazing incidence X-ray scattering measurements, is responsible for the creation of the surface localized defect states. We find that the density and spatial distribution of these defect states is a function of preparation conditions.
The Deep Underground Neutrino Experiment (DUNE) is a long-baseline neutrino experiment designed to mainly investigate oscillation parameters, supernova physics and proton decay. Its far detector will be composed of four liquid argon time projection chamber (LArTPC) underground modules, in South Dakota-USA, which will detect a neutrino beam produced at Fermilab, 1300 km away, where a near detector will be in place. The second DUNE far detector module, Vertical Drift, will be a single phase LArTPC with electron drift along the vertical axis with two volumes of 13.5 m x 6.5 m x 60 m dimensions separated by a cathode plane. The charge collection will be performed by two anode planes placed at the top and bottom of the module, each composed by stacked layers of a perforated PCB technology with electrode strips. The photon detection system (PDS) will make use of large size X-Arapuca tiles distributed over three detection planes. One plane will consist of a horizontal arrangement of double sided tiles installed on the high voltage cathode plane and two vertical planes, each placed on the longest cryostat membrane walls. A light active coverage of 14.8% over the cathode and 7.4% over the laterals should allow improvements in the low energy physics range that can be probed in DUNE, especially regarding supernova neutrinos (~10 MeV). We present the initial characterization of the Vertical Drift PDS using a Monte Carlo simulation and preliminary studies on its reconstruction capabilities at the MeV scale. The information obtained with the PDS alone should allow determination of a neutrino interaction region with a precision of at least 65 cm for events with deposited energy above 5 MeV and the deposited energy can be reconstructed with precision better than 10%, both at the center of the volume.