Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ULTRASONIC WAVES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Effect of Stress on Energy Flux Deviation of Ultrasonic Waves in Ultrasonic Waves in GR/EP Composites

Ultrasonic waves suffer energy flux deviation in graphite/epoxy because of the large anisotropy. The angle of deviation is a function of the elastic coefficients. For nonlinear solids, these coefficients and thus the angle of deviation is a function of stress. Acoustoelastic theory was used to model the effect of stress on flux deviation for unidirectional T300/5208 using previously measured elastic coefficients. Computations were made for uniaxial stress along the x3 axis fiber axis) and the x1 axis for waves propagating in the x1x3 plane. These results predict a shift as large as three degrees for the quasi-transverse wave. The shift in energy flux offers new nondestructive technique of evaluating stress in composites.

Prosser, William H.↗
NASA NTRS2006

Multimode-Guided-Wave Ultrasonic Scanning of Materials

Two documents discuss a method of characterizing advanced composite materials by use of multimode-guided ultrasonic waves. A transmitting transducer excites modulated (e.g., pulsed) ultrasonic waves at one location on a surface of a plate specimen. The waves interact with microstructure and flaws as they propagate through the specimen to a receiving transducer at a different location. The received signal is analyzed to determine the total (multimode) ultrasonic response of the specimen and utilize this response to evaluate microstructure and flaws. The analysis is performed by software that extracts parameters of signals in the time and frequency domains. Scanning is effected by using computer-controlled motorized translation stages to position the transducers at specified pairs of locations and repeating the measurement, data-acquisition, and data-analysis processes at the successive locations. One document presents results of a scan of a specimen containing a delamination.

Roth, Don↗
NASA NTRS1974

Optimizing signal-to-error ratio in standing wave ultrasonic measurements

Standing wave ultrasonic techniques for the measurement of very small changes in acoustic attenuation and phase velocity are discussed. Enhanced sensitivity to these small changes was achieved by making the specimen part of a composite ultrasonic resonator. It was found that a point of maximum sensitivity on the response of such an ultrasonic resonator need not coincide with a point of maximum signal-to-error ratio. A model is presented and analyzed which takes into account error due to long term (low frequency) noise effects such as gain drifts and dc level shifts. This model yields a quantitative value for the signal-to-error ratio in which the signal is defined as the ideal change in the monitored response and the error as the difference between the experimentally measured change and the signal. The specific frequency dependent forms for the ultrasonic response and the sensitivity enhancement factor were used to predict the operating point on a mechanical resonance corresponding to maximum signal-to-error ratio.

Brown, J. J.↗
NASA NTRS1990

Effect of stress on energy flux deviation of ultrasonic waves in GR/EP composites

Ultrasonic waves suffer energy flux deviation in graphite/epoxy because of the large anisotropy. The angle of deviation is a function of the elastic coefficients. For nonlinear solids, these coefficients and thus the angle of deviation is a function of stress. Acoustoelastic theory was used to model the effect of stress on flux deviation for unidirectional T300/5208 using previously measured elastic coefficients. Computations were made for uniaxial stress along the x3 axis (fiber axis) and the x1 for waves propagating in the x1x3 plane. These results predict a shift as large as three degrees for the quasi-transverse wave. The shift in energy flux offers a new nondestructive technique of evaluating stress in composites.

Prosser, William H.↗
NASA NTRS1994

Composite Material Property Nondestructive Characterization Using Obliquely Insonified Ultrasonic Waves

The analysis of reflected ultrasonic waves induced by oblique insonification of composite materials is a powerful tool for providing informations about defects and material properties. A device was developed to manipulate a pair of transmitting and receiving transducers at vrious angles of wave incidence and propagation with the fiber orientation.

Non-Destructive Evaluation Composites Mechanical P↗
NASA NTRS1972

Optical Production and Detection of Ultrasonic Waves in Metals for Nondestructive Testing

Ultrasonic waves were produced by striking the surface of a metal with the focused one-joule pulse of a Q-switched ruby laser. Rayleigh (surface) waves and longitudinal waves were detected with conventional transducers. Optical methods of detection were tested and developed. Rayleigh waves were produced with an oscillator and transducer. They were optically detected on curved polished surfaces, and on unpolished surfaces. The technique uses a knife edge to detect small angle changes of the surface as the wave pulse passes the illuminated spot. Optical flaw detection using pulse echo and attenuation is demonstrated.

Morrison, R. A.↗
NASA NTRS1997

Determination of Residual Stress in Composite Materials Using Ultrasonic Waves

The performance of high temperature composites can be significantly affected by the presence of residual stresses. These stresses arise during cooling processes from fabrication to room temperature due to mismatch of thermal expansion coefficients between matrix and fiber materials. This effect is especially pronounced in metal matrix and intermetallic composites. It can lead to plastic deformations, matrix cracking and fiber/matrix interface debonding. In this work the feasibility of ultrasonic techniques for residual stress assessment in composites is addressed. A novel technique for absolute stress determination in orthotropic materials from angular dependencies of ultrasonic velocities is described. The technique is applicable for determination of both applied and residual stresses and does not require calibration measurements on a reference sample. The important advantage of this method is that stress is determined simultaneously with stress-dependent elastic constants and is thus decoupled from the material texture. It is demonstrated that when the principal plane stress directions coincide with acoustical axes, the angular velocity data in the plane perpendicular to the stress plane may be used to determine both stress components. When the stress is off the acoustical axes, the shear and the difference of the normal stress components may be determined from the angular dependence of group velocities in the plane of stresses. Synthetic sets of experimental data corresponding to materials with different anisotropy and stress levels are used to check the applicability of the technique. The method is also verified experimentally. A high precision ultrasonic wave transmission technique is developed to measure angular dependence of ultrasonic velocities. Examples of stress determination from experimental velocity data are given. A method is presented for determination of velocities of ultrasonic waves propagating through the composite material with residual stresses. It is based on the generalized self-consistent multiple scattering model. Calculation results for longitudinal and shear ultrasonic wave velocities propagating perpendicular to the fibers direction in SCS-6/Ti composite with and without residual stresses are presented. They show that velocity changes due to presence of stresses are of order 1%.

Rokhlin, S. I.↗
NASA NTRS1971

Study of the Effects of Ultrasonic Waves on the Reproductive Integrity of Mammalian Cells Cultured in Vitro

The effects of monochromatic ultrasonic waves of 0.1, 0.5, 1.0, 2.0 and, 3.3 MHz frequency on the colony-forming ability of mammalian cells (M3-1,V79, Chang's and T-1) cultured in vitro have been studied to determine the nature of the action of ultrasonic energy on biological systems at the cellular level. The combined effect of ultrasound and X-rays has also been studied. It is concluded: (1) Ultrasonic irradiation causes both lethal and sublethal damage. (2) There is a threshold dose rate for lethal effects. (3) The effectiveness of ultrasonic waves in causing cell death probably depends on the frequency and the amplitude of the waves for a given cell line, indicating a possible resonance phenomenon.

Martins, B. I.↗
DOE OSTI2020

Ultrasonic waves from radial mode excitation of a piezoelectric disc on the surface of an elastic solid

In this work, we discuss the ultrasonic wave propagation characteristics in an isotropic elastic solid due to the radial mode excitation of a piezoelectric disc actuator bonded to its surface. Finite element simulations using coupled electromechanical modeling is employed to investigate the wave propagation behavior. We find that the radial mode vibrations on the surface of the elastic solid generates all the three types of ultrasonic waves: longitudinal, shear, and surface waves. The waves in the solid are comprised of a central lobe and multiple side lobes based on the frequency of the radial mode excitation. The central lobe is predominantly composed of longitudinal waves and the side lobes are composed of shear waves. While the longitudinal waves have a strong central lobe and weak side lobes that are not fully developed, shear waves consists of fully developed side lobes. In addition, we observe that the longitudinal waves have fewer side lobes inside the solid compared to the shear waves. A semi-analytical approach is presented to explain the above observations. The interface traction boundary condition between the piezoelectric disc and the elastic solid is approximated as a truncated 'Bessel' excitation over the area of the piezoelectric disc in contact with the solid. A Fourier–Bessel series expansion technique is used to investigate the wave propagation behavior from the above traction boundary condition. The results obtained explain the observations from the finite element simulations with regard to the number and distribution of side lobes pertaining to the longitudinal and shear waves generated from the radial modes of the piezoelectric disc. The proposed semi-analytical approach is general and can be applied to any arbitrary axisymmetric excitations on the surface of an elastic solid.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Determination of acoustic nonlinearity parameters using thermal modulation of ultrasonic waves

This study presents a test method and its theoretical framework to determine the acoustic nonlinearity parameters (α, β, δ) of material using thermal modulation of ultrasonic waves. Temperature change-induced thermal strain excites the nonlinear response of the material and modulates the ultrasonic wave propagating in it. Experimental results showed a strong correlation between the relative wave velocity change and the temperature change. With a quadratic polynomial model, the acoustic nonlinearity parameters were obtained from the polynomial coefficients by curve fitting the experimental data. Their effects on thermal-induced velocity change were discussed. The parameters α, β, and δ govern the hysteretic gap, average slope, and curvature of the correlation curve, respectively. The proposed theory was validated on aluminum, steel, intact and damaged concrete samples. The obtained nonlinear parameters show reasonable agreement with values reported in the literature. Compared to other nonlinear acoustic methods using vibration or acoustic excitation, the thermal modulation method generates more uniform, slow changing, and larger strain field in the test sample. Employing the thermal effect as the driving force for nonlinearity instead of an undesired influencing factor, this method can measure the absolute values of α, β, and δ with good accuracy using a simple ultrasonic test setup.

Physics↗