Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “U-Mo Alloys”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Dissolution Flowsheet for Skull Oxide Generated during U-Mo Alloy Casting for High Performance Research Reactor Fuel

The Savannah River National Laboratory was requested to develop dissolution flowsheets for high assay low enriched U scrap generated during the fabrication of high performance research reactor fuel. The scrap streams include U-10Mo and U-10Mo-Zr foils, rejected Al-clad fuel plates, and skull oxide from casting molds. Flowsheets for the dissolution of the U-10Mo-Zr foils and Al-clad U-10Mo-Zr mini-plates received from BWX Technologies, Inc were developed and demonstrated in the first phase of this project. In the second phase (this work), the skull oxide from a U-10Mo casting mold was obtained from the Y-12 National Security Complex (Y-12) and small-scale experiments were performed to demonstrate dissolution flowsheets.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Uranium–Molybdenum Alloy Critical Experiments for the Design of the Health Physics Research Reactor

Clean critical experiments with a uranium-molybdenum alloy (average of 10.1616 wt. % Mo with a density of 17.08 g/cm 3 ) were performed at the Oak Ridge Critical Experiments Facility in 1961 to support the design of the Health Physics Research Reactor (HPRR). The HPRR was similar to the Godiva burst reactor at Los Alamos National Laboratory and was designed to produce 50 microseconds burst of 10 17 fission pulses of radiation for dosimetry measurements, initially in support of the determination of the doses from the nuclear detonations in Japan during World War II. These experiments reported here were used to verify the calculational methods used to design the HPRR. These delayed critical measurements were:1) a solid unreflected and unmoderated 8-in.-dimeter U-Mo cylinder, 2) an unmoderated and unreflected annulus with 8-in.-outside diameter, 2-in.-inside diameter cylinder with a central void, 3) an unmoderated and unreflected annulus with 8-in.-outside diameter, 2-in.-inside diameter cylinder with a central void filled with stainless steel, 4) Same as 3) but with 3-in-thick Plexiglas reflector on top with and without cadmium between the reflector and the U-Mo alloy assembly with steel in the center, and 5) an unmoderated and unreflected annulus which was a modification of the second but with the lower 5 inches of the central hole enlarged to 3.5 in. with various reflector conditions. The reflector conditions were: 1-in.-thick Plexiglas on all outer surfaces-void in the center; 1-in.-thick Plexiglas on all outer surfaces-Plexiglas in the center; 2-in.- thick Plexiglas on radial surface-void in the center; 6-in.-thick Plexiglas on the bottom only-Plexiglas in the center; and 6-in.-thick Plexiglas on bottom, 1-in.-thick on top and on the lower 8.25-cm.-section of the radial surface-void in the center. For some of these reflector conditions 0.025-cm.thick cadmium was located between the reflector and the U-Mo alloy. The uranium contained 93.17 wt. % 235 U. Reflection was a safety concern for this unmoderated and unreflected reactor and reduction of reflection effects was also investigated by insertion of neutron absorber around the U-Mo alloy. The stainless steel 304 contained 18% nickel and 8% chromium and the rest iron. The reflector material was a methacrylate plastic (Plexiglas) containing 5.8 x 10 22 atoms/cm 3 of hydrogen and 3.6 x 10 22 atoms/cm 3 of carbon with a density of 1.20 g/cm 3 . The purpose of this report is to document the experimental information for the measurements performed so that at a later date researchers could perform the required uncertainty and calculational analyses and documentation to use these data for an International Nuclear Criticality Safety Benchmark Program (ICSBEP) or a EURATON Nuclear Energy Agency (NEA) benchmark. The data from the experiments described should be acceptable for use as criticality safety benchmark experiments for the ICSBEP and the NEA nuclear criticality safety benchmark program, once the uncertainty analysis is completed. Based on previous ICSBEP benchmarks with this enriched uranium metal at ORCEF, the uncertainties in k eff could be as low as ±0.0002 for some configurations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Formation of uranium nitride nanoparticles via mechanical alloying of uranium-molybdenum alloy fuels in gaseous nitrogen

Uranium-molybdenum (U-Mo) alloys show promise as a nuclear fuel system due to their high thermal conductivity and fuel loading capability. However, U-Mo systems are susceptible to irradiation induced swelling ultimately affecting the cladding via mechanical and chemical interactions. To address these shortcomings, this research investigated the formation of uranium mononitride (UN) nanoparticles within a 90 wt% U/10 wt% Mo (U-10Mo) matrix to act as a prospective defect sink for fission products at nanometric hetero-interfaces. To promote the formation of UN, U-10Mo powders were mechanically alloyed under a high purity nitrogen atmosphere. Variations of the milling process investigated included media size, duration of milling, and number of times the milling jar was re-aerated with nitrogen gas. Characterization of the fuel microstructure was completed using light element analysis, X-ray diffraction, scanning and transmission-electron microscopy, electron energy loss spectroscopy, and atom probe tomography. UN nanoparticles measuring 1–5 nm in radius were observed in the U-Mo matrix as early as 1 h into the mechanical alloying process. Milling time in excess of 10 h was found to lead to deleterious effects induced by the stainless-steel milling media.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

A Design and Fabrication Options Trade Study for Metallic Fuel without Internal Sodium Bonding

Nuclear fuels using alloys of uranium, or metallic fuels, have many beneficial properties. The classical metallic fuel design uses a loose fitting cylindrical “slug” of fuel placed inside stainless-steel cladding tubes where the gap is filled with sodium. This sodium bond is liquid at operating temperature and conducts heat from the slug to the cladding, especially in early life before fuel swells into contact with the cladding. Despite the benefits of sodium bonding, there is a desire to develop metallic fuel technologies without it chiefly to reduce chemical reaction hazards in spent fuel storage from sodium fast reactors operating on once-through fuel cycles. Elimination of the sodium bond may also help unlock potential benefits for fuel fabrication, reactor neutronics, and compatibility with other types of reactors. Creating a sodium-free metallic fuel revolves around the problem of manufacturing fuel slug geometries which are in close contact with the cladding at beginning of life to facilitate heat transport while alleviating fuel-cladding chemical interactions (FCCI) at this interface and providing enough free volume to accommodate fuel swelling. Accelerating development and qualification of this fuel system will require careful selection of design and manufacturing options. To this end, a design trade-off study was performed to evaluate candidate options. Several design and manufacturing options were assessed, weighted, scored, and ranked with respect to fabrication, normal reactor operation, off-normal scenarios, and back-end considerations. This effort was performed both for “baseline” needs, which represented a once-through fuel cycle at temperatures and burnups known to be viable for sodium-bonded metallic fuel, and for “enhanced” needs to represent opportunities for closed fuel cycles and/or more aggressive temperatures/burnups. The outcomes of this study prioritized a baseline technology using U-Zr alloy with additives to mitigate FCCI, produced in annular slug geometry by continuous casting, clad in austenitic stainless-steel alloy, and followed by a final step to swage the cladding down to close the gap. This study prioritized an enhanced fuel technology using U-Mo alloy, also produced by continuous casting into an annular geometry, followed by coating/plating with an FCCI barrier on the slug, again with a final step to swage the cladding diameter down using oxide dispersion strengthened steel. It was noted that development of the enhanced fuel technology would entail more risk, thus U-Zr alloy was put forth as a backup to U-Mo if challenges are encountered with FCCI barriers, and advanced ferritic/martensitic steels are put forth as a backup to oxide dispersion strengthened steels if swaging and welding are found unworkable.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Formation and Consolidation of UN Nanostructures in U-Mo Fuel via Mechanical Alloying and Spark Plasma Sintering

Uranium-molybdenum (U-Mo) alloys show promise as a nuclear fuel system due to their high thermal conductivity and high fuel loading capability. However, U-Mo systems suffer from irradiation induced swelling ultimately affecting the cladding via mechanical and chemical interaction. To address these shortcomings, this thesis investigated the formation of uranium mononitride (UN) nanoparticles within a U-10Mo matrix. To promote the formation of UN, U-10Mo powders were mechanically alloyed under a high purity nitrogen cover gas (99.9995%) atmosphere. Variations were made in stainless steel milling media size, duration of milling, and number of times the milling jar was re-aerated with nitrogen gas. UN nanoparticulates were successfully formed within the U-Mo matrix and was characterized utilizing light element analysis, X-ray diffractometry, scanning and transmission-electron microscopy, electron energy loss spectroscopy, and atom probe tomography. Presence of the UN nanoparticles was found as early as 1-hour into the mechanical alloying process, and significant iron contamination found after 10-hours of milling. The U-Mo/UN powders were compacted using spark plasma sintering techniques in order to stabilize the nanostructure. U-Mo/UN compacts containing small amounts of neodymium and helium were analyzed to observe the defect migration tendencies of fission products within the fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Nuclear Fuel and Pu Redox Studies from The Glenn T. Seaborg Institute at Idaho National Laboratory

The Glenn T. Seaborg Institute at Idaho National Laboratory (INL-GTSI) focuses on advancing fundamental research in the actinide sciences by providing unique opportunities to early career scientists and engineers to gain experience studying the actinide elements and their associated systems. The INL-GTSI is built from three focus areas that are based on the expertise and supporting infrastructure at INL and include solid state chemistry and physics, solution phase chemistry and physics, and forensic and isotope science. INL is the lead Laboratory for nuclear energy research and development in the U. S. and the research on nuclear fuels performed under the INL-GTSI gives good examples of solid state studies. Uranium-Molybdenum (U-Mo) alloys are leading fuel candidates for conversion of high performance research and test reactors to low-enriched fuels. During irradiation, generated fission gas accumulates into bubbles and self-organizes into a gas bubble superlattice (GBS) that effectively stores fission gases and inhibits fuel swelling. A study on the early self- organizing behavior of the GBS shows that not only grain boundaries but the interfaces between the U-Mo matrix and uranium carbide (UC) impurities are important to GBS formation.[1] In solution, understanding the complex redox behavior of plutonium in aqueous environments is critical for establishing optimized nuclear waste reprocessing solvent systems and storage tank environments. INL-GTSI researchers have produced an experimentally validated multi-scale model of the gamma radiation induced behavior of plutonium ions in concentrated aqueous HNO3 solutions.[2] Here, gamma radiation effected only minimal steady state changes in the redox distribution of the plutonium oxidation states. The redox cycling between Pu(IV) and Pu(III) is demonstrated to be mediated by the •OH/NO3• radical oxidation of Pu(III) and the H2O2/HNO3 driven reduction of Pu(IV). The INL-GTSI offers young researchers the unique chance to work directly with actinide bearing materials in a U. S. National Laboratory environment. Further topical areas of interest to the INL-GTSI include, but are not limited to, fundamental actinide properties, structure/property (electronic, magnetic, thermal) relations, actinide quantum criticality, f- electron interactions, electron correlations, computational studies, new phases, defect effects, interface interactions, isotope production and separation, forensic analytical chemistry, structure and dynamic properties of actinides in non-aqueous media, separations chemistry and kinetics for advanced nuclear fuel cycles, radiation effects, and innovative and advanced ligand design for complexation of the actinides.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Purification of U from U-10Mo scrap generated during the fabrication of high performance research reactor fuel

A low enriched U-Mo alloy fuel is under development to replace highly enriched U fuels currently used in United States high performance research reactors. The alloy casting and fuel fabrication processes will generate scrap streams containing low enriched U (LEU) which must be recovered. Solvent extraction processes were designed using the Argonne Model for Universal Solvent Extraction (AMUSE) to purify solutions containing 20 and 50 g/L U. The feed for the solvent extraction processes was prepared from solutions generated from the dissolution of U-10Mo-Zr foils and U-10Mo-Zr-Al mini-plates. The U purification processes were demonstrated using two, 16-stage banks of miniature mixer-settlers. The solvent extraction experiments demonstrated that all design objectives for the U purification processes could be met. The U recovery in the product stream for each flowsheet was ≥99.9%. The flowsheet demonstrations also showed that the purity of the U Product will meet the requirements of the ASTM International C1462-21 specification for LEU metal enriched to less than 20% 235 U. In conclusion, the AMUSE modeling for both flowsheet demonstrations was validated by comparing predicted and measured concentrations of U, Mo, and Zr in the exit streams and stage samples at steady-state conditions in the mixer-settlers.

modified PUREX process↗
DOE OSTI2022

Computational determination of a primary diffusion mode in γ U-10Mo under irradiation

Low enriched uranium (< 20 % 235 U)-molybdenum (U-Mo) monolithic fuel is the primary candidate for high performance research and test reactors, and is in the process of being qualified to replace highly enriched uranium (≥ 20 % 23 5U) fuel. As part of the qualification process, it is critical to understand and predict the behavior of fission gas bubbles under irradiation, which affects fuel swelling and fuel failure. Mechanistic fuel models are being developed that can both reproduce the existing experimental data for fuel swelling, and be further applied to irradiation conditions beyond the experimental scope. Diffusion of species under irradiation conditions is an important parameter in the mechanistic fuel models; however, no temperature-relevant experimental diffusion data exists. In the present work, radiation-enhanced diffusion coefficients of U, Mo, and Xe in λU-10wt.%Mo were calculated in the temperature range between 300 K and 1400 K via rate-theory models and molecular dynamics simulations with an embedded-atom method interatomic potential for the U-Mo-Xe system. Accordingly, total diffusion coefficients under relevant irradiation conditions are determined using previously obtained intrinsic thermal diffusion and radiation-driven diffusion coefficients, as well as the newly calculated radiation-enhanced diffusion coefficients presented herein. Radiation-enhanced diffusion of U and Mo was dominant in the intermediate temperature range, whereas radiation-enhanced diffusion of Xe did not significantly contribute to total diffusion of Xe at the relevant fission rate densities. Radiation-enhanced diffusion of Xe became faster than both intrinsic thermal diffusion and radiation-driven diffusion at a fission rate density of 5 x 10 22 fissions/m 3 /s, which is higher than the typical fission rate density range in research reactors. The temperature regime that radiation-enhanced diffusion of each element dominated was dependent on the fission rate density. Finally, the total diffusion coefficients of U, Mo, and Xe, updated in this work, will be utilized as parameters in the mechanistic fuel models to help predict the behavior of fission gas bubbles under irradiation more accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

A Critical Review on the History of Fabricating Monolithic U-Mo Fuel Plates

Fabrication of uranium-molybdenum alloy fuels has been occurring since the early 2000s in support of the development of a high-uranium-density low-enrichment fuel for use in high-performance research and test reactors which operate at relatively low temperatures. The primary fuel form—a thin foil of uranium, alloyed with 10wt% molybdenum, which is coated in a layer of zirconium and then encapsulated with aluminum 6061 as a cladding material—was developed over a number of years.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Molecular dynamics studies of grain boundary mobility and anisotropy in BCC γ-uranium

Grain morphologies such as grain size and aspect ratio in uranium-based metallic fuels are important microstructural features that can impact various fuel performance properties such as fission-gas-induced swelling, thermal transport, high burnup structure formation, and radiation resistance. Accurate prediction of the fuel grain morphologies requires knowledge of critical grain growth parameters such as grain boundary (GB) mobility and anisotropy. In this work, molecular dynamics simulations were performed to study the GB mobility and its anisotropy in pure body-centered-cubic (BCC) γ uranium. Nine GBs with different combinations of misorientation angles (20°, 30°, 45°) and rotation axes (<100>, <110>, <111>), as well as an additional <111> 38.2° GB were studied using three interatomic potentials. Here, it is found that the GB mobility anisotropy has complex trends, depending on both rotation axis and misorientation. However, in general the <110> rotation axis has the fastest GB mobility at the same misorientation. The results of this work can be used as not only baselines for future studies of GB mobility in uranium-based alloys such as uranium-molybdenum (U-Mo) fuels, but also input for mesoscale modeling of grain growth in uranium-based alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

A critical review of the history of fabricating monolithic U-Mo fuel plates

The fabrication of monolithic uranium-molybdenum alloy fuels, specifically those developed for high-performance research and test reactors, began in the early 2000s. The primary fuel form consists of uranium alloyed with 10-wt% molybdenum in a thin foil coated with zirconium and encapsulated in aluminum-6061 cladding. Over the years, the process has evolved with different types of casting, heat treatments, rolling schedules, and cladding applications. This review examines the history of these fabrication processes and their impact on microstructure and fuel-swelling performance. Even though various fabrication methods were used, we found little correlation between fabrication variation and fuel swelling. This insensitive relationship between fabrication variation and fuel swelling is primarily due to inhomogeneous microstructures that formed during casting and grain refinement that occurred during rolling. We conclude that the fabrication processes we examined produced similar microstructures, indicating that the fuel microstructure is somewhat insensitive to the fabrication parameters evaluated. However, the relatively small amount of historic data, such as those for grain sizes, limited this analysis. More recently fabricated materials, such as those from ongoing irradiation experiment, Mini-Plate-1 and Mini-Plate-2, were also excluded from this analysis and are intended to be reviewed separately. The findings, that fuel microstructure is somewhat insensitive to the fabrication parameters, do not imply that any fabrication method is acceptable, given the uncertainties in data and fuel-swelling observations. For example, only arc melting and vacuum induction melting casting processes were previously explored in the historic fabrication efforts. In conclusion, the findings should not be extrapolated to other casting processes.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Mapping the Microstructure During the Historic U-Mo Monolithic Fuel Foil Fabrication Process

Since 2004, there has been extensive effort towards the development of a uranium molybdenum monolithic fuel system to convert high performance research and test reactors. The RERTR-6 experiment was the first to attempt a monolithic fuel instead of a dispersed fuel form. The fabrication methods evolved overtime and provided the basis for current fabrication methods. The various steps in the process inevitably tailor the fuel alloy microstructure which is known to influence irradiation behavior. This document aims to present and discuss the fabrication evolution that transpired through a recounting of historical data from the various fabrication campaigns. By overlaying this data with basic science studies on the U-Mo that explored transformation kinetics, it is possible to estimate a measure of the impact heat treatments have on the final as-fabricated microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

FAST Irradiations, Postirradiation Examinations, and Modeling of U-Mo for Light Water Reactor Applications

Many next generation light water reactor (LWR) concepts, such as mobile small modular reactors, are seeking to use smaller core dimensions than conventional reactor types. Smaller reactor cores require an increase in fissile material to maintain reactivity. For non-proliferation purposes, enrichment increases are limited to less than 20% (high assay low enriched uranium, [HALEU]) and so higher uranium density fuels than UO 2 must be considered. To this end, uranium-molybdenum alloys were tested using the Fission Accelerated Steady-state Test (FAST) approach. The experiment test matrix is focused on identifying the temperature transition between low swelling and high fission gas retention to break away swelling and low fission gas retention. This paper documents the results of irradiation tests and post-irradiation examinations (PIE) including neutron radiography, rodlet profilometry, fission gas collection analysis, and optical metallography. The results of these tests showed that unconstrained U-Mo fuels (solid, Na-bonded rodlets) have a swelling threshold between 400-450°C with minimal fission gas release below this point. Higher temperature solid fuel showed microstructural zoning with small pore networks while lower temperature solid fuels have a uniform microstructure with large pore networks. U-Annular Mo fuels where swelling had some self-constraint imposed upon it, were shown to have much reduced swelling compared to their solid counterparts as well as very low fission gas release for irradiation temperatures up to 500°C. These initial results show that the use of U-Mo in constrained fuel geometries could be used as a high uranium density HALEU fuel for LWRs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Evaluation of Oak Ridge National Laboratory Health Physics Research Reactor Operation Data for Critical Benchmark Creation

The Oak Ridge National Laboratory (ORNL) Health Physics Research Reactor (HPRR) was a research reactor designed and built at ORNL in 1961. The critical assembly used a highly enriched uranium and molybdenum alloy as the fuel and could be operated in steady-state or burst modes. The HPRR has recently been the object of an investigation to create a criticality benchmark. Such benchmarks are very important, as they are used primarily to show the accuracy of newly developed modeling codes and to help experimental validation and reactor licensing. The evaluated experiments considered in this paper were carried out between 1974 and 1986 from various HPRR activities such as steady-state subcritical, steady-state critical, and burst prompt super-critical operations of the reactor for dosimetry, irradiation, or training purposes. By using the HPRR experimental logbook information and the as-built drawings of the critical assembly, a highly detailed model of the HPRR was created with SCALE 6.2.4/KENO-VI, and a first version of a critical benchmark of the HPRR was developed following the International Criticality Safety Benchmark Evaluation Project (ICSBEP) guidelines for thorough description and uncertainty/sensitivity quantification. Unfortunately, in most of the evaluated experiments, the obtained difference between calculated and experimental k eff is around 1,000 pcm, corresponding to a relative error of approximately 1%, beyond the quality standards of the ICSBEP recommending a relative error below 0.1%. Moreover, the derived experimental uncertainty is high, around 4% relative, mainly due to the U-Mo fuel density uncertainty, but also from numerous other factors. For these reasons, the creation of a valuable critical benchmark from HPRR operation data is thus far compromised. In this paper, the different steps of the experiments’ evaluation are summarized, and the reasons for the experimental/calculation discrepancies and potential ways to solve them are explored. This paper also aims to remind us always to exercise considerable care when performing experimental work, and to record all the data possible for potential future uses.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Entrapment Behavior of Solid Surrogate Fission Products at Engineered UN Nano‐Hetero‐Interfaces Within Metallic Nuclear Fuels

Nanometric hetero-interfaces provide a wealth of scientific and engineering opportunities due to their complex and often misunderstood properties that can differ from their respective bulk constituents. In this work, the ability for engineered nanostructures within a bulk U─Mo alloy to arrest simulant fission products is investigated experimentally and computationally. Nanostructured 90 wt% U/ 10 wt% Mo (U-10Mo) with 7.1 at% Nd is consolidated using spark-plasma- sintering (SPS) techniques and is heat-treated at 500 °C under vacuum for 24, 100, 500, and 1000 h. Analysis on the sintered and heat-treated U-10Mo reveals rapid kinetics in Nd diffusion to nanocluster sites, with evidence of Nd diffusion occurring during sintering and during the following heat-treatment. The segregation behavior of Nd at two different U─Mo/UN interfaces is computationally verified using density functional theory (DFT) to reinforce experimental data.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Irradiation performance of a U-7Mo in Al-Si matrix dispersion full-size fuel plate assembly

The Korea Atomic Energy Research Institute (KAERI) is leading the Ki-Jang Research Reactor (KJRR) project with the intent to develop a new reactor for medical isotope production and other nuclear research purposes. The KJRR core is designed to use high density fuel system where uranium alloyed with 7 wt% molybdenum (U-7Mo) particles are dispersed in a matrix of aluminum alloyed with 5 wt% silicon (Al-5Si) and clad in aluminum alloy 6061 (Al-6061) to form fuel plates. KAERI developed a fabrication facility to construct KJRR fuel assemblies and partnered with the Idaho National Laboratory (INL) to irradiate a full-size fuel assembly, with 21 total fuel plates, in the Advanced Test Reactor (ATR). Irradiation testing and subsequent Post Irradiation Exam (PIE) campaigns were performed successfully over a multi-year project. Monte Carlo neutronic calculations, coupling with a depletion code, were performed based on ATR’s as-run power history which showed that the highest power plate (plate 20) reached 83.1 % end-of-life (EOL) local burnup based on initial 235 U content. Additionally, finite element thermal modeling was performed based as-run power history which showed a beginning-of-life (BOL) peak local heat flux of 184 W/cm 2 . No anomalous fuel performance was observed during the irradiation and target test conditions were achieved. PIE showed favorable performance of the fuel assembly regarding all important phenomena. This paper describes the KJRR fuel assembly irradiation conditions and PIE data to support the conclusion that it performed well, without evidence of unexpected or problematic fuel performance, within an irradiation test designed to bound the KJRR design environment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Mechanical Properties of Irradiated U-10 wt. %Mo Alloy Degraded by Porosity Development

In this study, a plate-type nuclear fuel consisting of a solid monolithic foil of U-10 wt. %Mo is under development for use in the United States' high-performance research reactors. In support of developing this fuel, the fuel has been fabricated for the first time by a commercial fuel vendor and subsequently irradiated in a test reactor. This provides an opportunity to evaluate postirradiation mechanical properties of the commercially fabricated fuel. Four-point bend testing was conducted on the irradiated U-10Mo samples to generate the fuel material properties, including the modulus of elasticity and the bending strength. Although the material behaves in a brittle manner due to the accumulated porosity, a general trend of strength and modulus reduction was found as fission density increases. The data produced was evaluated using both Weibull statistics and a modulus degradation model with recommendations provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

IER 517: Molybdenum Critical Experiment Design [Slides]

In nuclear fuels, U-Mo metallic fuels are used in new space reactor designs and new research reactor fuels. MITR, MURR, and NBSR reactors plan on converting from different HEU fuels to a U-Mo HALEU fuel. In spend nuclear fuel, 95 Mo is one of the 15 main absorbing fission products in irradiated LWR fuel. This makes it important for criticality safety studies in transportation and reprocessing. In structural materials. Molybdenum is found commonly in alloys that make up the structural materials of nuclear reactors such as type 316 SS. Molybdenum helps to improve high temperature performance and corrosion resistance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗