SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The design and operation of a hydrogen-air ignition torch presently being used to burn off excess hydrogen that accumulates in the scrubber exhaust ducts of two rocket engine test facilities at the NASA Lewis Research Center in Cleveland, Ohio, is described.
A small, uncooled plasma torch was developed and used in combination with an injector designed to study ignition and flameholding in hydrogen-fueled supersonic flows. The plasma torch was operated on mixtures of hydrogen and argon with total flows of 10 to 70 scfh. The fuel injector design consisted of five small upstream pilot fuel injectors, a rearward facing step for recirculation, and three main fuel injectors downstream of the step. The plasma torch was located in the recirculation region, and all injection was perpendicular to the Mach 2 stream. Both semi-freejet and ducted tests were conducted. The experimental results indicate that a low power plasma torch operating on a 1:1 volumetric mixture of hygrogen and argon and located in the recirculation zone fueled by the upstream pilot fuel injectors is a good igniter for flow conditions simulating a flight Mach number of 3.7. The total temperature required to autoignite the hydrogen fuel for this injector geometry was 2640 R. The injector configuration was shown to be a good flameholder over a wide range of total temperature. Spectroscopic measurements were used to verify the presence of air total temperatures below 1610 R.
A small, uncooled plasma torch was developed and used in combination with an injector designed to study ignition and flameholding in hydrogen-fueled supersonic flows. The plasma torch was operated on mixtures of hydrogen and argon with total flows of 10 to 70 scfh. The fuel injector design consisted of five small upstream pilot fuel injectors, a rearward facing step for recirculation, and three main fuel injectors downstream of the step. The plasma torch was located in the recirculation region, and all injection was perpendicular to the Mach 2 stream. Both semi-freejet and ducted tests were conducted. The experimental results indicate that a low power plasma torch operating on a 1:1 volumetric mixture of hydrogen and argon and located in the recirculation zone fueled by the upstream pilot fuel injectors is a good igniter for flow conditions simulating a flight Mach number of 3.7. The total temperature required to autoignite the hydrogen fuel for this injector geometry was 2640 R. The injector configuration was shown to be a good flameholder over a wide range of total temperature. Spectroscopic measurements were used to verify the presence of air total temperatures below 1610 R.
The objective of this dissertation is to characterize augmented spark impinging (torch) igniters. Torch igniters inject propellants into a small prechamber where a spark igniter imparts the activation energy to initiate combustion. The flame stabilizes within the prechamber and exits into the main combustion chamber where it ignites the main flow directly or by mixing with a coaxial flow to create a secondary flame. The underlying phenomena that promote reliable ignition are multifaceted and required a broad scope of investigations. Initial efforts focused on spark discharges across an annular geometry. Gaseous propellent projects the electrical arc toward the prechamber, where the arc and the thermal energy is imparted to the surrounding fluid then meets with a combustible mixture. Discharges are parametrically examined against pressure, spark-gap size, and exciter types to emulate transient engine startup. The energy imparted to the flow, approximate velocity, and distance traveled by the exhaust plume are determined. Spark quenching (no energy deposition) and its effects on perceived versus actual measurements are shown. Results outline the prechamber target zone where a combustible mixture is necessary for ignition. Next, three-dimensional, time-accurate, and nonreacting computational fluid dynamics simulations assess effects of geometric and mass flow differences on the size, location, and composition of a combustible mixture. Fluid dynamic phenomena are elucidated. Correlations between nondimensional variables are found. Results are coupled with a conservation-law analysis to produce novel objective functions. Lastly, a full-scale, modular torch igniter is tested. Injector sizes, mixture ratios, and injector momentum ratios are systematically varied to map ignition probability and ignition delay. Results show the importance of local mixture ratios, provide injector momentum ratios guidelines, and demonstrate reliable ignition of core mixture ratios typically outside flammability limits. The deliverable of this project is not a torch igniter or derivative thereof. Instead, this dissertation produces novel objective-functions for igniter design. These equations are functions of variables that may be constrained by engine-level requirements, physics, and experimental results from this work. They provide a foundation for future igniter design and will minimize iterative processes from the design cycle for next-generation ignition hardware.
An investigation was conducted in an altitude test chamber at the NACA Lewis Laboratory to determine the altitude starting characteristics of an afterburner with autoignition and with hot-streak ignition. Transient afterburner ignition data were obtained over a range of altitudes from 30,000 to 50,000 feet at a flight Mach number of 0.60. Afterburner ignition with a torch igniter located axially at approximately the midpoint of the combustion chamber was possible over the entire range, but ignition ignition with a torch igniter located in the transition section 1 5/8 inches upstream of the turbine stators proved unsatisfactory at an altitude of 50,000 feet due to the inability to obtain flame through the turbine. Increasing the afterburner-inlet total pressure at a constant afterburner fuel-air ratio decreased the afterburner ignition time. Hot-streak ignition was possible within 2 seconds after the time required to obtain the preset, normal afterburner fuel pressure, whereas autoignition required 4 to 7 seconds for the range of altitudes investigated. Following the ignition there was a period of oscillatory operation existing in the engine-afterburner before steady-state operation was attained. The time required for steady-state stable operation decreased as afterburner inlet total pressure increased. The duration of oscillations also decreased with hot-streak ignition because the fuel-air mixture was ignited before a large volume of combustible mixture was accumulated in the afterburner.
A plasma torch system designed for ignition and flame-holding in supersonic combustion studies has been modified, in order to decrease electrode wear and increase stability, through the incorporation of a flow swirler in the gas inlet that adds vortex-stabilization to the arc. The torch body was redesigned in order to achieve superior alignment of the electrodes; the electrode gap was made continuously adjustable, thereby allowing fine tuning during torch operation. Table operation of the improved torch has been demonstrated in pure nitrogen, eliminating the requirement of argon gas for arc stabilization.
Preheating of fuel and injection into a plasma torch plume fro adjacent the plasma torch plume provides for only ignition with reduced delay but improved fuel-air mixing and fuel atomization as well as combustion reaction enhancement. Heat exchange also reduced erosion of the anode of the plasma torch. Fuel mixing atomization, fuel mixture distribution enhancement and combustion reaction enhancement are improved by unsteady plasma torch energization, integral formation of the heat exchanger, fuel injection nozzle and plasma torch anode in a more compact, low-profile arrangement which is not intrusive on a highspeed air flow with which the invention is particularly effective and further enhanced by use of nitrogen as a feedstock material and inclusion of high pressure gases in the fuel to cause effervescence during injection.
This paper describes the results of a study to define the ignition characteristics and thruster pulse mode capabilities of the GOX/ethanol propellant combination. Ignition limits were defined in terms of mixture ratio and cold flow pressure using a spark initiated torch igniter. Igniter tests were run over a wide range of cold flow pressure, propellant temperature and mixture ratio. The product of cold flow pressure and igniter chamber diameter was used to correlate mixture ratio regimes of ignition and nonignition. Engine ignition reliability and pulse mode capability were demonstrated using a 620 lbF thruster with an integrated torch igniter. The nominal chamber pressure and mixture ratio were 150 psia and 1.8, respectively, thruster tests were run over a wide range of chamber pressures and mixture ratios. The feasibility of thruster pulse mode operation with the non-hypergolic GOX/ethanol propellant combination was demonstrated.
Tests were conducted with the RS18 rocket engine using liquid oxygen (LO2) and liquid methane (LCH4) propellants under simulated altitude conditions at NASA Johnson Space Center White Sands Test Facility (WSTF). This project is part of NASA s Propulsion and Cryogenics Advanced Development (PCAD) project. "Green" propellants, such as LO2/LCH4, offer savings in both performance and safety over equivalently sized hypergolic propellant systems in spacecraft applications such as ascent engines or service module engines. Altitude simulation was achieved using the WSTF Large Altitude Simulation System, which provided altitude conditions equivalent up to approx.120,000 ft (approx.37 km). For specific impulse calculations, engine thrust and propellant mass flow rates were measured. Propellant flow rate was measured using a coriolis-style mass-flow meter and compared with a serial turbine-style flow meter. Results showed a significant performance measurement difference during ignition startup. LO2 flow ranged from 5.9-9.5 lbm/sec (2.7-4.3 kg/sec), and LCH4 flow varied from 3.0-4.4 lbm/sec (1.4-2.0 kg/sec) during the RS-18 hot-fire test series. Thrust was measured using three load cells in parallel. Ignition was demonstrated using a gaseous oxygen/methane spark torch igniter. Data was obtained at multiple chamber pressures, and calculations were performed for specific impulse, C* combustion efficiency, and thrust vector alignment. Test objectives for the RS-18 project are 1) conduct a shakedown of the test stand for LO2/methane lunar ascent engines, 2) obtain vacuum ignition data for the torch and pyrotechnic igniters, and 3) obtain nozzle kinetics data to anchor two-dimensional kinetics codes.
Tests were conducted with the RS-18 rocket engine using liquid oxygen (LO2) and liquid methane (LCH4) propellants under simulated altitude conditions at NASA Johnson Space Center White Sands Test Facility (WSTF). This project is part of NASA's Propulsion and Cryogenics Advanced Development (PCAD) project. "Green" propellants, such as LO2/LCH4, offer savings in both performance and safety over equivalently sized hypergolic propulsion systems in spacecraft applications such as ascent engines or service module engines. Altitude simulation was achieved using the WSTF Large Altitude Simulation System, which provided altitude conditions equivalent up to ~122,000 ft (~37 km). For specific impulse calculations, engine thrust and propellant mass flow rates were measured. LO2 flow ranged from 5.9 - 9.5 lbm/sec (2.7 - 4.3 kg/sec), and LCH4 flow varied from 3.0 - 4.4 lbm/sec (1.4 - 2.0 kg/sec) during the RS-18 hot-fire test series. Propellant flow rate was measured using a coriolis mass-flow meter and compared with a serial turbine-style flow meter. Results showed a significant performance measurement difference during ignition startup due to two-phase flow effects. Subsequent cold-flow testing demonstrated that the propellant manifolds must be adequately flushed in order for the coriolis flow meters to give accurate data. The coriolis flow meters were later shown to provide accurate steady-state data, but the turbine flow meter data should be used in transient phases of operation. Thrust was measured using three load cells in parallel, which also provides the capability to calculate thrust vector alignment. Ignition was demonstrated using a gaseous oxygen/methane spark torch igniter. Test objectives for the RS-18 project are 1) conduct a shakedown of the test stand for LO2/methane lunar ascent engines, 2) obtain vacuum ignition data for the torch and pyrotechnic igniters, and 3) obtain nozzle kinetics data to anchor two-dimensional kinetics codes. All of these objectives were met with the RS-18 data and additional testing data from subsequent LO2/methane test programs in 2009 which included the first simulated-altitude pyrotechnic ignition demonstration of LO2/methane.
The design, fabrication, and demonstration of a 111 newton (25 lb) thrust, integrated auxiliary propulsion system (IAPS) thruster for use with LH2/LO2 propellants is described. Hydrogen was supplied at a temperature range of 22 to 33 K (40 to 60 R), and oxygen from 89 to 122 K (160 to 220 R). The thruster was designed to operate in both pulse mode and steady-state modes for vehicle attitude control, space maneuvering, and as an abort backup in the event of failure of the main propulsion system. A dual-sleeve, tri-axial injection system was designed that utilizes a primary injector/combustor where 100 percent of the oxygen and 8 percent of the hydrogen is introduced; a secondary injector/combustor where 45 percent of the hydrogen is introduced to mix with the primary combustor gases; and a boundary layer injector that uses the remaining 45 percent of the hydrogen to cool the thrust throat/nozzle design. Hot-fire evaluation of this thruster with a BLC injection distance of 2.79 cm (1.10 in.) indicated that a specific impulse value of 390 sec can be attained using a coated molybdenum thrust chamber. Pulse mode tests indicated that a chamber pressure buildup to 90 percent thrust can be achieved in a time on the order of 48 msec. Some problems were encountered in achieving ignition of each pulse during pulse trains. This was interpreted to indicate that a higher delivered spark energy level ( 100 mJ) would be required to maintain ignition reliability of the plasma torch ignition system under the extra 'cold' conditions resulting during pulsing.
As part of NASA's technology development of liquid methane / liquid oxygen engines for future exploration missions, two different igniters were recently studied at NASA Marshall Space Flight Center. The first igniter tested was an impinging injection, spark-initiated torch igniter, and the second was a microwave-generated plasma igniter. The purpose of the ignition tests was to define the ignition limits under vacuum conditions and characterize the transient start-up performance as a function of propellant mixture ratio (MR), mass flow rates, inlet temperatures, and pre-ignition chamber pressure. In addition, for the impinging igniter two different spark plugs were tested, and for the microwave igniter the magnetron filament warm-up time and the magnetron input power were both varied. The results gathered from these tests indicated that the impinging igniter is capable of operating over an MR range of 2 - 27, with methane and oxygen inlet temperatures as low as -161 F and -233 F, respectively. The microwave igniter was tested over an MR range of 2 - 9, with methane and oxygen inlet temperatures as low as -90 F and -200 F, respectively. The microwave igniter achieved ignition over this range, although an upper ignition limit was determined for the oxidizer mass flow rate. In general, the torch exhaust temperatures for the microwave igniter were not as high as those attained with the impinging igniter. The microwave igniter, however, was hot-fired 17 times and was still operational, whereas the impinging igniter spark plugs experienced thermal shock and erosion over nine hot-fire tests. It was concluded that for the microwave igniter better mixing of the propellants might be required in order to both raise the torch exhaust temperature and decrease the required magnetron input power, and for the impinging igniter the spark plug position within the igniter chamber should be varied in future tests to identify a more optimal location. All of the igniter tests were supported by the Propulsion & Cryogenics Advanced Development project, which is part of NASA's Exploration Technology Development Program.
The fiber optically coupled laser ignition approach summarized is under consideration for use in igniting bi-propellant rocket thrust chambers. This laser ignition approach is based on a novel dual pulse format capable of effectively increasing laser generated plasma life times up to 1000 % over conventional laser ignition methods. In the dual-pulse format tinder consideration here an initial laser pulse is used to generate a small plasma kernel. A second laser pulse that effectively irradiates the plasma kernel follows this pulse. Energy transfer into the kernel is much more efficient because of its absorption characteristics thereby allowing the kernel to develop into a much more effective ignition source for subsequent combustion processes. In this research effort both single and dual-pulse formats were evaluated in a small testbed rocket thrust chamber. The rocket chamber was designed to evaluate several bipropellant combinations. Optical access to the chamber was provided through small sapphire windows. Test results from gaseous oxygen (GOx) and RP-1 propellants are presented here. Several variables were evaluated during the test program, including spark location, pulse timing, and relative pulse energy. These variables were evaluated in an effort to identify the conditions in which laser ignition of bi-propellants is feasible. Preliminary results and analysis indicate that this laser ignition approach may provide superior ignition performance relative to squib and torch igniters, while simultaneously eliminating some of the logistical issues associated with these systems. Further research focused on enhancing the system robustness, multiplexing, and window durability/cleaning and fiber optic enhancements is in progress.
Since late 2005, NASA s Marshall Space Flight Center (MSFC) has been developing and demonstrating technology for liquid oxygen and methane (LOX/CH4) engine designs. Efforts were undertaken to help advance technology that might benefit NASA s Exploration Technology Development Program. The propellant combination has gained interest as a potential option for the ascent stage main propulsion system on the Altair lunar lander vehicle. The propellants are also attractive for eventual Mars missions in future development activities. MSFC s efforts focus on evaluating the performance potential of both liquid and gaseous methane for specific injector designs. Previous JANNAF papers reported the performance observed for LOX and methane with an impinging injector. More recent efforts have focused on testing coaxial injector designs. Hot-fire testing performed at MSFC with thrust levels close to 5000 lbf demonstrated high performance with coaxial injectors of different element densities and various fuel film cooling levels. Test data provided results on performance, chamber wall compatibility, and heat flux profiles for different injectors. A variety of igniters were also demonstrated, including a torch igniter and a microwave (or plasma) igniter.
A hydrogen-air ignition torch concept that had been used successfully in two rocket engine test facilities to consume excess hydrogen in their exhausters at atmospheric conditions was experimentally evaluated and developed in an altitude test facility at NASA Lewis Research Center. The idea was to use several of these torches in conjunction with hydrogen detectors and dilution air to prevent excess accumulation of unburned hydrogen or mixtures of hydrogen and air exceeding the sea-level lower flammability limit in the altitude facility exhaust system during hydrogen-fueled propulsion system tests. The torches were evaluated for a range of fuel-to-air ratios from 0.09 to 0.39 and for a range of exit diameters from 19/64 to 49/64 in. From the results of these tests a torch geometry and a fuel-to-air ratio were selected that produced a reasonably sized torch exhaust flame for consumption of unburned hydrogen at altitude pressures from sea level to 4 psia.
A hydrogen-air ignition torch concept that had been used successfully in two rocket engine test facilities to consume excess hydrogen in their exhausters at atmospheric conditions was experimentally evaluated and developed in an altitude test facility at NASA Lewis Research Center. The idea was to use several of these torches in conjunction with hydrogen detectors and dilution air to prevent excess accumulation of unburned hydrogen or mixtures of hydrogen and air exceeding the sea-level lower flammability limit in the altitude facility exhaust system during hydrogen-fueled propulsion system tests. The torches were evaluated for a range of fuel-to-air ratios from 0.09 to 0.39 and for a range of exit diameters from 19/64 to 49/64 in. From the results of these tests a torch geometry and a fuel-to-air ratio were selected that produced a reasonably sized torch exhaust flame for consumption of unburned hydrogen at altitude pressures from sea level to 4 psia.
Carbon monoxide and oxygen ignition boundaries were determined in a spark torch igniter as a function of propellant inlet temperatures. The oxygen temperature was varied from ambient to -258 F, and the carbon monoxide temperature was varied from ambient to -241 F. With the oxygen and carbon monoxide at -253 F and -219 F, respectively, they successfully ignited between mixture ratios of 2.42 and 3.10. Analysis of the results indicated that the lower ignition boundary was more sensitive to oxygen temperature than to carbon monoxide temperature. Another series of tests was performed in a small simulated rocket engine with oxygen at -197 F and carbon monoxide at -193 F. An oxygen/hydrogen flame was used to initiate combustion of the oxygen and carbon monoxide. Tests performed at the optimum operating mixture ratio of 0.55 obtained steady-state combustion in every test.
In support of NASA's efforts to advance methane technology for future exploration missions, two different igniter concepts were developed and tested at NASA's Marshall Space Flight Center for ignition of oxygen/methane propellants. The first type of igniter, an impinging injection, spark-initiated torch igniter (impinging igniter), used traditional spark plug technology to produce a small, but very intense, pulsed plasma as the ignition source. The second type of igniter, a microwave-generated plasma igniter (microwave igniter), used a microwave magnetron to produce a continuous, larger-volume plasma as the ignition source. Two new designs for both types of igniters were leveraged off past oxygen/methane igniter designs that were tested at MSFC and documented in a 2008 JANNAF paper. In this most recent work, the two new igniters were to be tested at the component level as well as inside a liquid oxygen/liquid methane (LOX/LCH4) 40-element swirl coaxial injector. Although the microwave igniter achieved ignition in every test, it encountered technical difficulties that prevented it from being tested with the injector. The impinging igniter required several design iterations as well as testing at different mixture ratios and mass flow rates before reliable operation with minimal ignition delay was achieved. The final design of the impinging igniter was successfully tested in the LOX/LCH4 injector. The same igniter was later re-configured and component-tested to demonstrate reliable ignition of oxygen/hydrogen propellants. Future tests of the impinging igniter will include ignition of a LOX/hydrogen two-stage swirl injector, which is one of several injector concepts being tested in the Lunar Lander Descent Engine Test Bed at MSFC. All igniter and injector tests have been funded by the Propulsion & Cryogenics Advanced Development project managed by Glenn Research Center and sponsored by NASA s Exploration Technology Development Program.