Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Titanium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Synthesis of Titanium Oxycarbide from Titanium Slag by Methane-Containing Gas

In this study, reaction steps of a process for synthesis of titanium oxycarbide from titanium slag were demonstrated. This process involves the reduction of titanium slag by a methane-hydrogen-argon mixture at 1473 K (1200 °C) and the leaching of the reduced products by hydrofluoric acid near room temperature to remove the main impurity (Fe{sub 3}Si). Some iron was formed by disproportionation of the main M{sub 3}O{sub 5} phase before gaseous reduction started. Upon reduction, more iron formed first, followed by reduction of titanium dioxide to suboxides and eventually oxycarbide.

36 MATERIALS SCIENCE↗

Aqueous Synthesis of Technetium-Doped Titanium Dioxide by Direct Oxidation of Titanium Powder, a Precursor for Ceramic Nuclear Waste Forms

Technetium-99 (Tc) is a problematic fission product that complicates the long-term disposal of nuclear waste due to its long half-life, high fission yield, and the environmental mobility of pertechnetate, its stable form in aerobic environments. One approach to preventing Tc contamination is through incorporation into durable waste forms based on weathering-resistant minerals such as rutile (titanium dioxide). Here, the incorporation of technetium into titanium dioxide by means of simple, aqueous chemistry - direct oxidation of titanium powder in the presence of ammonium fluoride - is achieved. X-ray absorption fine structure spectroscopy and diffuse reflectance spectroscopy indicate that Tc(IV) replaces Ti(IV) within the structure. Rather than being incorporated as isolated Tc(IV) ions, Tc is present as pairs of edge-sharing Tc(IV) octahedra similar to molecular Tc(IV) complexes such as [(H 2 EDTA)TcIV](μ-O) 2 . Technetium-doped TiO 2 was suspended in deionized water under aerobic conditions, and the Tc leached under these conditions was followed for 8 months. The normalized release rate of Tc (LR Tc ) from the TiO 2 particles is low (3 × 10 -6 g m -2 d -1 ), which illustrates the potential utility of TiO 2 as waste form. However, the small size of the as-prepared TiO 2 nanoparticles results in an estimated retention of Tc of 10 4 years, which is only a fraction of the half-life of Tc (2.1 × 10 5 years).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tensile and creep properties of titanium-vanadium, titanium-molybdenum, and titanium-niobium alloys

Tensile and creep properties of experimental beta-titanium alloys were determined. Titanium-vanadium alloys had substantially greater tensile and creep strength than the titanium-niobium and titanium-molybdenum alloys tested. Specific tensile strengths of several titanium-vanadium-aluminum-silicon alloys were equivalent or superior to those of commercial titanium alloys to temperatures of 650 C. The Ti-50V-3Al-1Si alloy had the best balance of tensile strength, creep strength, and metallurgical stability. Its 500 C creep strength was far superior to that of a widely used commercial titanium alloy, Ti-6Al-4V, and almost equivalent to that of newly developed commercial titanium alloys.

Gray, H. R.↗

Fully CMOS-compatible titanium nitride nanoantennas

CMOS-compatible fabrication of plasmonic materials and devices will accelerate the development of integrated nanophotonics for information processing applications. Using low-temperature plasma-enhanced atomic layer deposition (PEALD), we develop a recipe for fully CMOS-compatible titanium nitride (TiN) that is plasmonic in the visible and near infrared. Films are grown on silicon, silicon dioxide, and epitaxially on magnesium oxide substrates. By optimizing the plasma exposure per growth cycle during PEALD, carbon and oxygen contamination are reduced, lowering undesirable loss. We use electron beam lithography to pattern TiN nanopillars with varying diameters on silicon in large-area arrays. In the first reported single-particle measurements on plasmonic TiN, we demonstrate size-tunable darkfield scattering spectroscopy in the visible and near infrared regimes. Finally, the optical properties of this CMOS-compatible material, combined with its high melting temperature and mechanical durability, comprise a step towards fully CMOS-integrated nanophotonic information processing.

36 MATERIALS SCIENCE↗

Titanium, vanadium and chromium valences in silicates of ungrouped achondrite NWA 7325 and ureilite Y-791538 record highly-reduced origins

Titanium, Cr, and V valences were determined by applying micro-X-ray Absorption Near Edge Structure (micro-XANES) spectroscopy methods to individual grains of olivine and pyroxene in the ungrouped achondrite NWA 7325 and ureilite Y-791538, as well as to plagioclase in NWA 7325. The advantages of applying multiple, multivalent-element-based oxybarometers to individual grains are (1) the ability to cover the entire oxygen fugacity (fO2) range encountered in nature, and (2) the increased reliability from consistent results for semi-independent fO2 proxies. fO2 values were inferred from each mineral valence determination after correcting with available laboratory-experiment-derived, valence-specific partition coefficients to obtain melt valences and then calibrating with the fO2 values of the relevant equal species proportions points suggested for igneous (primarily basaltic) systems. The resulting olivine and pyroxene valences are highly reduced and similar in the two meteorites with substantial fractions of Cr2+, Ti3+ and V2+. The exception is Cr in NWA 7325 pyroxene which is much more oxidized than the Cr in its olivine. Chromium and Ti in plagioclase in NWA 7325 is relatively oxidized (V valence not determined). The anomalously oxidized Cr in NWA 7325 pyroxene may be due to a secondary reheating event that oxidized Cr in the pyroxene without similarly oxidizing Ti and V. Such a separation of the redox couples may be an effect of re-equilibration kinetics, where the valence of Cr would be more rapidly modified. These valences yielded similar mean fO2s for the two meteorites; IW-3.1 ± 0.2 for NWA 7325 and IW-2.8 ± 0.2 for Y-791538, consistent with an origin of NWA 7325 in either Mercury or an asteroid that experienced redox conditions similar to those on the ureilite parent body.

58 GEOSCIENCES↗

Tensile properties of cast titanium alloys: Titanium-6Al-4V ELI and Titanium-5Al-2.5Sn ELI

This work was performed to determine the tensile properties of cast, hot isostatic pressed (HIP'ed), and annealed titanium alloys, Ti-6Al-4V ELI and Ti-5Al-2.5Sn ELI, that are candidate materials for the space transportation main engine (STME) liquid hydrogen turbopump impeller. Samples of the cast alloys were HIP'ed, annealed, and machined into tensile specimens. The specimens were tested in air at ambient temperature (70 F) and also at -423 F in liquid hydrogen. The Ti-6Al-4V alloy had an average ultimate strength of 129.1 ksi at 70 F and 212.2 ksi at -423 F. The Ti-5Al-2.5Sn alloy had an average ultimate strength of 108.4 ksi at 70 degrees F and 185.0 ksi at -423 F. The ductility, as measured by reduction of area, for the Ti-6Al-4V averaged 15.2 percent at 70 F and 8.7 percent at -423 F, whereas for the Ti-5Al-2.5Sn alloy average reduction of area was 24.6 percent at 70 F and 11.7 percent at -423 F.

Billinghurst, E. E., Jr.↗

Origin of Nanoscale Phase Stability Reversals in Titanium Oxide Polymorphs

We have monitored the hydrothermal crystallization of titania nanoparticles by in situ X-ray diffraction (XRD). Using the refined average structures from the XRD measurements, we calculated potential energy variations with particle size on periodic bulk structures using density functional theory (DFT). These variations cannot account for the enthalpy required to stabilize anatase relative to rutile. Thus, the hypothesis that the strain of the surface structure of nanoparticles accounts for the stabilization of anatase is not applicable to the growth of titania in water. DFT calculations on model nanoparticles do generate lower surface energies for anatase than for rutile that are large enough to explain the stability reversal in nanoparticles relative to the bulk phase. Rather than arising from two-dimensional surface structure alone, as previously thought, the total surface energies are critically dependent upon defects associated with edges and corners of nanocrystals at particle sizes ?3 nm (i.e., during the nucleation process). As the particles grow, the bulk free energy becomes relatively more important, causing rutile to become stable at larger particle sizes. This study quantifies for the first time the critical role of edge and vertex energies in determining the relative phase stabilities of TiO2 nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The effects of ultra-fine-grained structure and cryogenic temperature on adiabatic shear localization in titanium

The deformation at low temperatures (173 K and 77 K) in ultrafine-grained (100 and 500 nm) titanium is investigated and its effect on adiabatic shear localization is established. In comparison with coarse grained titanium, the strength of ultrafine-grained titanium is higher due to the classic Hall-Petch effect while the strain hardening approaches zero. Our results show that shear localization in dynamic deformation is also altered. The width of the shear band of coarse-grained titanium decreases from 30 to 18 mm (by 40%) with decreasing the initial deformation temperature to 77 K. In contrast, for 100 nm titanium, the width of shear band decreases more significantly, from 4 mmat room temperature to 1 mm (a 75% decrease) at 77 K. This difference is attributed to the combined effects of the decrease in the thermal conductivity and specific heat capacity, and the increase in thermal softening rate. These changes in the width are consistent with the predictions of the Grady and Bai-Dodd theories. Ultrafine- and nanorecrystallized grains are observed inside the bands which are dependent on initial grain size and initial deformation temperature. Here, the dislocation evolution is evaluated for the different conditions using a Kocks-Mecking formulation; the rotational dynamic recrystallization mechanism responsible for forming the ultrafine/nanosized grains (40-250 nm) is successfully modeled incorporating the differences in initial temperature and grain size. Our results and analysis are important in enhancing the understanding of the structural evolution processes under high strain-rates and cryogenic temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterisation of titanium-titanium boride composites processed by powder metallurgy techniques

In this work, a detailed characterisation of titanium-titanium boride composites processed by three powder metallurgy techniques, namely, hot isostatic pressing, spark plasma sintering and vacuum sintering, was conducted. Two composites with different volume percents of titanium boride reinforcement were used for the investigation. One was titanium with 20% titanium boride, and the other was titanium with 40% titanium boride (by volume). Characterisation was performed using X-ray diffraction, electron probe micro analysis - energy dispersive spectroscopy and wavelength dispersive spectroscopy, image analysis and scanning electron microscopy. The characterisation results confirm the completion of the titanium boride reaction. The results reveal the presence of titanium boride reinforcement in different morphologies such as needle-shaped whiskers, short agglomerated whiskers and fine plates. The paper also discusses how mechanical properties such as microhardness, elastic modulus and Poisson's ratio are influenced by the processing techniques as well as the volume fraction of the titanium boride reinforcement. - Highlights: Black-Right-Pointing-Pointer Ti-TiB composites were processed by HIP, SPS and vacuum sintering. Black-Right-Pointing-Pointer The completion of Ti-TiB{sub 2} reaction was confirmed by XRD, SEM and EPMA studies. Black-Right-Pointing-Pointer Hardness and elastic properties of Ti-TiB composites were discussed. Black-Right-Pointing-Pointer Processing techniques were compared with respect to their microstructure.

36 MATERIALS SCIENCE↗

Radiation Damage Studies on Titanium Alloys as High Intensity Proton Accelerator Beam Window Materials

A high-strength dual a+ß phase titanium alloy Ti–6Al–4V is utilized as a material for beam windows in several accelerator target facilities. However, relatively little is known about how material properties of this alloy are affected by high-intensity proton beam irradiation. With plans to upgrade neutrino facilities at J-PARC and Fermilab to over 1 MW beam power, the radiation damage in the window material will reach a few displacements per atom (dpa) per year, significantly above the ~0.3 dpa level of existing data. The international RaDIATE collaboration, Radiation Damage In Accelerator Target Environments, has conducted a high intensity proton beam irradiation of various target and window material specimens at Brookhaven Linac Isotope Producer (BLIP) facility, including a variety of titanium alloys. Post-Irradiation Examination (PIE) of the specimens in the 1st capsule, irradiated at up to 0.25 dpa, is in progress. Tensile tests in a hot cell at Pacific Northwest National Laboratory (PNNL) exhibited a clear signature of radiation hardening and loss of ductility for Ti–6Al–4V, while Ti–3Al–2.5V, with less ß phase, exhibited less severe hardening. Microstructural investigations will follow to study the cause of the difference in tensile behavior between these alloys. High-cycle fatigue (HCF) performance is critical to the lifetime estimation of beam windows exposed to a periodic thermal stress from a pulsed proton beam. The first HCF data on irradiated titanium alloys are to be obtained by a conventional bend fatigue test at Fermilab and by an ultrasonic mesoscale fatigue test at Culham Laboratory. Specimens in the 2nd capsule, irradiated at up to ~1 dpa, cover typical titanium alloy grades, including possible radiation-resistant candidates. These systematic studies on the effects of radiation damage of titanium alloy materials are intended to enable us not only to predict realistic lifetimes of current beam windows made of Ti–6Al–4V, but also to extend the lifetime by choosing a more radiation and thermal shock tolerant alloy with a preferable heat treatment, or even by developing new materials.

Titanium Alloy, Beam Window, Proton Beam, Radiatio↗

Formation of Titanium Sulfide from Titanium Oxycarbonitride by CS{sub 2} Gas

Previously this group reported that a good quality titanium metal powder can be produced from titanium sulfides by electrochemical OS process. In this study, the sulfurization procedure was examined to synthesize titanium sulfide from titanium oxycarbonitride by CS{sub 2} gas. The experiments were carried out in the temperature range of 1173 K to 1523 K (900 °C to 1250 °C) in a tube reactor with continuously flowing argon (Ar) as carrier gas of CS{sub 2}. The formation of titanium sulfide phases from the commercial TiN, TiC, and TiO powders was studied as the initial step. Then, TiO{sub 0.02}C{sub 0.13}N{sub 0.85} coming from ilmenite was sulfurized to prepare single phase of titanium sulfide. The products were characterized by X-ray diffraction, and the morphology of the sulfides was rigorously investigated, and the sulfur, oxygen, and carbon contents in the products were analyzed. The process was remarkably dependent on the temperature and time. TiN and TiO{sub 0.02}C{sub 0.13}N{sub 0.85} powders could be fully converted to the single phase of Ti{sub 2.45}S{sub 4} (Ti{sub 2+x}S{sub 4}) at 1473 K (1200 °C) in 3.6 ks. The maximum weight gain of TiN sample was ~ 55.3 pct indicating a full conversion of TiN to Ti{sub 2}S{sub 3} phase. The carbon and oxygen contents in this sulfide prepared from the oxycarbonitride were about 1.8 wt pct C and 1.4 wt pct O, respectively. Therefore, the titanium sulfide could be a promising feedstock for the production of commercial grade titanium powder.

36 MATERIALS SCIENCE↗

ECCI based characterization of dislocation shear in polycrystalline arrays during heterogeneous deformation of commercially pure titanium

A new electron channeling contrast imaging (ECCI) based approach for the characterization of heterogeneous plastic deformation across multiple grains in a polycrystal is presented. The nature of the shear accommodation at grain boundaries has been assessed by evaluating the spatial distribution of dislocations and slip system activities near the boundaries and relating these observations to standard slip transfer criteria and the global state of stress. The direction of slip band propagation, and consequently the location of dislocation slip band nucleation, was determined by characterizing the slip band widths across individual grains. This assessment leads to a better understanding of the factors involved in polycrystalline deformation, including the grain boundary shear accommodation associated with both dislocation pile-ups and grain boundary dislocation nucleation. Because ECCI allows study of dislocation structures over large surface areas, and thus larger overall volumes than typically are accessible by other techniques, the overall approach allows the dislocation distribution across individual grains to be understood in terms of the broader polycrystalline constraints.

36 MATERIALS SCIENCE↗