SEARCH · Engineering Papers

Results for “TRIP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS2016

You Can't Reach for the Stars if You are Tripping Over the Ground! (Preventing Slips, Trips, and Falls)

Although there are very few mishaps related to ground, vehicle or payload processing at the Kennedy Space Center (KSC), employees have experienced a significant number of injuries due to slips, trips, and falls outside of performing flight processing operations. Slips, trips, and falls are major causes of occupational injuries at KSC, the National Aeronautics and Space Administration (NASA), and in general industry. To help KSC employees avoid these injuries, and allow them to be fully productive, KSC launched an initiative in 2013 to reduce slips, trips, and falls. This initiative is based on a four-part model focusing on DATA analysis, HAZARD awareness, PREVENTIVE methods, and BALANCE.

Falls↗

NASA NTRS1995

Mars Pathfinder Landing Site Workshop 2: Characteristics of the Ares Vallis Region and Field Trips in the Channeled Scabland, Washington

Mars Pathfinder will place a single lander on the surface of Mars on July 4, 1997, following a December 1996 launch. As a result of the very successful first Mars Pathfinder Landing Site Workshop, the project has selected the Ares Vallis outflow channel in Chryse Planitia as the landing site. This location is where a large catastrophic outflow channel debouches into the northern lowlands. A second workshop and series of field trips, entitled Mars Pathfinder Landing Site Workshop 2: Characteristics of the Ares Vallis Region and Field Trips in the Channeled Scabland, Washington, were held in Spokane and Moses Lake, Washington. The purpose of the workshop was to provide a focus for learning as much as possible about the Ares Vallis region on Mars before landing there. The rationale is that the more that can be learned about the general area prior to landing, the better scientists will be able interpret the observations made by the lander and rover and place them in the proper geologic context. The field trip included overflights and surface investigations of the Channeled Scabland (an Earth analog for the martian catastrophic outflow channels), focusing on areas particularly analogous to Ares Vallis and the landing site. The overflights were essential for placing the enormous erosional and depositional features of the Channeled Scabland into proper three-dimensional context. The field trips were a joint educational outreach activity involving K-12 science educators, Mars Pathfinder scientists and engineers, and interested scientists from the Mars scientific community. Part 1 of the technical report on this workshop includes a description of the Mars Pathfinder mission, abstracts accepted for presentation at the workshop, an introduction to the Channeled Scabland, and field trip guides for the overflight and two field trips. This part, Part 2, includes the program for the workshop, summaries of the workshop technical sessions, a summary of the field trips and ensuing discussions, late abstracts of workshop presentations, reports on the education and public outreach activities carried out by the educators, and a list of the workshop and field trip participants.

Golombek, M. P.↗

NASA NTRS2015

Boundary Layer Transition and Trip Effectiveness on an Apollo Capsule in the JAXA High Enthalpy Shock Tunnel (HIEST) Facility

Computational assessments were performed to size boundary layer trips for a scaled Apollo capsule model in the High Enthalpy Shock Tunnel (HIEST) facility at the JAXA Kakuda Space Center in Japan. For stagnation conditions between 2 MJ/kg and 20 MJ/kg and between 10 MPa and 60 MPa, the appropriate trips were determined to be between 0.2 mm and 1.3 mm high, which provided kappa/delta values on the heatshield from 0.15 to 2.25. The tripped configuration consisted of an insert with a series of diamond shaped trips along the heatshield downstream of the stagnation point. Surface heat flux measurements were obtained on a capsule with a 250 mm diameter, 6.4% scale model, and pressure measurements were taken at axial stations along the nozzle walls. At low enthalpy conditions, the computational predictions agree favorably to the test data along the heatshield centerline. However, agreement becomes less favorable as the enthalpy increases conditions. The measured surface heat flux on the heatshield from the HIEST facility was under-predicted by the computations in these cases. Both smooth and tripped configurations were tested for comparison, and a post-test computational analysis showed that kappa/delta values based on the as-measured stagnation conditions ranged between 0.5 and 1.2. Tripped configurations for both 0.6 mm and 0.8 mm trip heights were able to effectively trip the flow to fully turbulent for a range of freestream conditions.

Kirk, Lindsay C.↗

NASA NTRS1992

Heat transfer in rotating serpentine passages with trips skewed to the flow

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multi-pass, heat transfer model with both radially inward and outward flow. Trip strips, skewed at 45 deg to the flow direction, were machined on the leading and trailing surfaces of the radial coolant passages. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature, rotation number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from similar stationary and rotating models with smooth walls and with trip strips normal to the flow direction. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation and buoyancy, decreased to as low as 40 percent of the value without rotation. However, the maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels previously obtained with the smooth wall models. It was concluded that (1) both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips, (2) the effects of rotation are markedly different depending upon the flow direction, and (3) the heat transfer with skewed trip strips is less sensitive to buoyancy than the heat transfer in models with either smooth or normal trips. Therefore, skewed trip strips rather than normal trip strips are recommended and geometry-specific tests are required for accurate design information.

Johnson, B. V.↗

NASA NTRS1996

Flow in Rotating Serpentine Coolant Passages With Skewed Trip Strips

Laser velocimetry was utilized to map the velocity field in serpentine turbine blade cooling passages with skewed trip strips. The measurements were obtained at Reynolds and Rotation numbers of 25,000 and 0.24 to assess the influence of trips, passage curvature and Coriolis force on the flow field. The interaction of the secondary flows induced by skewed trips with the passage rotation produces a swirling vortex and a corner recirculation zone. With trips skewed at +45 deg, the secondary flows remain unaltered as the cross-flow proceeds from the passage to the turn. However, the flow characteristics at these locations differ when trips are skewed at -45 deg. Changes in the flow structure are expected to augment heat transfer, in agreement with the heat transfer measurements of Johnson, et al. The present results show that trips are skewed at -45 deg in the outward flow passage and trips are skewed at +45 deg in the inward flow passage maximize heat transfer. Details of the present measurements were related to the heat transfer measurements of Johnson, et al. to relate fluid flow and heat transfer measurements.

Tse, David G.N.↗

NASA NTRS2013

Trip-Induced Transition Measurements in a Hypersonic Boundary Layer Using Molecular Tagging Velocimetry

Measurements of mean streamwise velocity, fluctuating streamwise velocity, and instantaneous streamwise velocity profiles in a hypersonic boundary layer were obtained over a 10-degree half-angle wedge model. A laser-induced fluorescence-based molecular tagging velocimetry technique was used to make the measurements. The nominal edge Mach number was 4.2. Velocity profiles were measured both in an untripped boundary layer and in the wake of a 4-mm diameter cylindrical tripping element centered 75.4 mm downstream of the sharp leading edge. Three different trip heights were investigated: k = 0.53 mm, k = 1.0 mm and k = 2.0 mm. The laminar boundary layer thickness at the position of the measurements was approximately 1 mm, though the exact thickness was dependent on Reynolds number and wall temperature. All of the measurements were made starting from a streamwise location approximately 18 mm downstream of the tripping element. This measurement region continued approximately 30 mm in the streamwise direction. Additionally, measurements were made at several spanwise locations. An analysis of flow features show how the magnitude, spatial location, and spatial growth of streamwise velocity instabilities are affected by parameters such as the ratio of trip height to boundary layer thickness and roughness Reynolds number. The fluctuating component of streamwise velocity measured along the centerline of the model increased from approximately 75 m/s with no trip to +/-225 m/s with a 0.53-mm trip, and to +/-240 m/s with a 1-mm trip, while holding the freestream Reynolds number constant. These measurements were performed in the 31-inch Mach 10 Air Tunnel at the NASA Langley Research Center.

Bathel, Brett F.↗

NASA NTRS1971

Round trip landing missions to the asteroid Eros, 1981 opportunity

A comprehensive, Del V (magnitude of impulsive velocity-change vector) study of short staytime (0 to 30 days), short total trip time (10 to 160 days) round trip landing missions (fast missions) is presented. The characteristics of the following selected round trip landing missions are described: mission A (fast mission) with 120-day total trip time, 0-day stay-time, and 73,000-fps total mission Del V; mission B (opposition class) with 380-day total trip time, 0-day staytime, and 52,000-fps total mission Del V; and mission C (conjuction class) with 540-day total trip time, 175-day staytime, and 39,000-fps total mission Del V. A study of large-tank Agena, chemical propulsion stage (CPS), and nuclear stage was conducted. A payload of 5000 pounds was assumed. The propulsion requirements for mission A were found to be two large-tank Agenas and ten CPSs (or alternatively, two large-tank Agenas and five nuclear stages) while mission B required two large-tank Agenas and two CPSs. Mission C can be performed with one large-tank Agena and one CPS.

Zambo, G. A.↗

NASA NTRS1992

Heat transfer in rotating serpentine passages with trips skewed to the flow

Johnson, B. V.↗

NASA NTRS1995

Flow in serpentine coolant passages with trip strips

Under the subject contract, an effort is being conducted at Scientific Research Associates, Inc. (SRA) to obtain flow field measurements in the coolant passage of a rotating turbine blade with ribbed walls, both in the stationary and rotating frames. The data obtained will be used for validation of computational tools and assessment of turbine blade cooling strategies. The configuration of the turbine blade passage model is given, and the measuring plane locations are given. The model has a four-pass passage with three 180 turns. This geometry was chosen to allow analyses of the velocity measurements corresponding to the heat transfer results obtained by Wagner. Two passes of the passage have a rectangular cross-section of 1.0 in x 0.5 in. Another two passes have a square cross-section of 0.5 in x 0.5 in. Trips with a streamwise pitch to trip height (P/e) = 5 and trip height to coolant passage width (e/Z) = 0.1, were machined along the leading and trailing walls. These dimensions are typical of those used in turbine blade coolant passages. The trips on these walls are staggered by the half-pitch. The trips are skewed at +/- 45 deg, and this allows the effect of trip orientation to be examined. Experiments will be conducted with flow entering the model through the 1.0 in x 0.5 in rectangular passage (Configuration C) and the 0.5 in x 0. 5 in square passage (Configuration D) to examine the effect of passage aspect ratio. Velocity measurements were obtained with a Reynolds number (Re) of 25,000, based on the hydraulic diameter of and bulk mean velocity in the half inch square passage. The coordinate system used in presenting the results for configurations C and D, respectively, is shown. The first, second and third passes of the passage will be referred to as the first, second and third passages, respectively, in later discussion. Streamwise distance (x) from the entrance is normalized by the hydraulic diameter (D). Vertical (y) and tangential (z) distances are normalized by the half passage height (H) and width (Z), respectively. The x coordinate and U component are positive in the streamwise direction. The y coordinate and V component are positive against gravity. The z coordinate and W component are positive in the direction of rotation. The velocities are normalized by the bulk mean velocity (Ub) of 3.44 m/s based on the half-inch square passage. The contours of the 1.0 in x 0.5 in and 0.5 in x 0.5 in passages were evaluated from 11 x 30 and 9 x 30 measurement grids, respectively.

Tse, D. G.-N.↗

NASA NTRS2007

Fluorescence Visualization of Hypersonic Flow Past Triangular and Rectangular Boundary-layer Trips

Planar laser-induced fluorescence (PLIF) flow visualization has been used to investigate the hypersonic flow of air over surface protrusions that are sized to force laminar-to-turbulent boundary layer transition. These trips were selected to simulate protruding Space Shuttle Orbiter heat shield gap-filler material. Experiments were performed in the NASA Langley Research Center 31-Inch Mach 10 Air Wind Tunnel, which is an electrically-heated, blowdown facility. Two-mm high by 8-mm wide triangular and rectangular trips were attached to a flat plate and were oriented at an angle of 45 degrees with respect to the oncoming flow. Upstream of these trips, nitric oxide (NO) was seeded into the boundary layer. PLIF visualization of this NO allowed observation of both laminar and turbulent boundary layer flow downstream of the trips for varying flow conditions as the flat plate angle of attack was varied. By varying the angle of attack, the Mach number above the boundary layer was varied between 4.2 and 9.8, according to analytical oblique-shock calculations. Computational Fluid Dynamics (CFD) simulations of the flowfield with a laminar boundary layer were also performed to better understand the flow environment. The PLIF images of the tripped boundary layer flow were compared to a case with no trip for which the flow remained laminar over the entire angle-of-attack range studied. Qualitative agreement is found between the present observed transition measurements and a previous experimental roughness-induced transition database determined by other means, which is used by the shuttle return-to-flight program.

Danehy, Paul M.↗

NASA NTRSDate not supplied

Laminar to Turbulence Transition in Boundary Layers due to Tripping Devices

Direct numerical simulations (DNS)and linear stability analysis were performed to identify the mechanisms by which two-and three-dimensional trips promote early transition in subsonic boundary layers over a flat plate. Investigations were conducted for two boundary layer transition trip configurations: one is a two-dimensional rectangular-shaped rod and the other is a three-dimensional zigzag tape. Reynolds numbers based on the trip heights are 683 and 300 for the two-and three-dimensional trips, respectively. Simulations with the two-dimensional trip showed that the flow separates at the top of the trip and forms a long recirculation zone downstream. However, the flow remains steady in the simulation without any external disturbances. Linear stability analysis showed that the inflectional profile in the recirculation zone is strongly unstable to frequencies in the range of 100-300 Hz. Simulations with the external disturbances forced at the frequency of 200 Hz showed that disturbances grow strongly inside the recirculation zone as observed in the Klebanoff1 experiment.

Transition↗

NASA NTRSDate not supplied

Laminar to Turbulence Transition in Boundary Layers due to Tripping Devices

Direct numerical simulations (DNS)and linear stability analyses were performed to identify the mechanisms by whichtwo-and three-dimensional trips promote early transition in subsonic boundary layers over a flat plate. Investigations were conducted for threeboundary-layer transition trip configurations:a two-dimensional smooth hump,a two-dimensional rectangular-shapedrod and a three-dimensional zig-zagtape. The smooth hump was used by Park et al.1in the linear and nonlinear parabolized stability (PSE) computations. Reynolds numbersbased on the tripheights are 710, 683,and 300 for the two-and three-dimensional trips, respectively. Simulations withthe smooth hump showed that the flow becomes stable upstream and strongly unstable downstream of the hump. Simulations with the two-dimensional rectangular trip showed that the flow separates at the top of the trip and forms a long recirculation zonedownstream. However, the flow remains steady in the simulation without any external disturbances. Linear stability analysis showed that the inflectional profile in the recirculation zone is strongly unstable to frequencies in the range of 100-300 Hz. Simulations with the external disturbances forced at the frequency of 200 Hz showed that disturbances grow strongly inside the recirculation zone as observed in the Klebanoff2 experiment. Three-dimensional simulations with secondary disturbances of fundamental, subharmonic, and oblique types produced turbulent flows shortlydownstream. The three-dimensional zig-zag trip with a small roughness Reynolds number lead to early breakdown to a turbulent flow.

Stability↗

NASA NTRS1985

The passive control of compressible boundary layer growth by boundary layer trips

The passive control of compressible boundary layer growth by boundary layer trips has been studied experimentally. Axisymmetric trips and three dimensional trips were used in this study. The nomial freestream Mach numbers are 1.5 and 4. The results show that trips are effective in promoting boundary layer growth. Trips are more effective for Mach 1.5 flows than for Mach 4 flows.

Chou, J. H.↗

NASA NTRS1960

Analysis of Trajectory Parameters for Probe and Round-Trip Missions to Venus

For one-way transfers between Earth and Venus, charts are obtained that show velocity, time, and angle parameters as functions of the eccentricity and semilatus rectum of the Sun-focused vehicle conic. From these curves, others are obtained that are useful in planning one-way and round-trip missions to Venus. The analysis is characterized by circular coplanar planetary orbits, successive two-body approximations, impulsive velocity changes, and circular parking orbits at 1.1 planet radii. For round trips the mission time considered ranges from 65 to 788 days, while wait time spent in the parking orbit at Venus ranges from 0 to 467 days. Individual velocity increments, one-way travel times, and departure dates are presented for round trips requiring the minimum total velocity increment. For both single-pass and orbiting Venusian probes, the time span available for launch becomes appreciable with only a small increase in velocity-increment capability above the minimum requirement. Velocity-increment increases are much more effective in reducing travel time for single-pass probes than they are for orbiting probes. Round trips composed of a direct route along an ellipse tangent to Earth's orbit and an aphelion route result in the minimum total velocity increment for wait times less than 100 days and mission times ranging from 145 to 612 days. Minimum-total-velocity-increment trips may be taken along perihelion-perihelion routes for wait times ranging from 300 to 467 days. These wait times occur during missions lasting from 640 to 759 days.

Dugan, James F., Jr.↗

NASA NTRS2021

Wake Instability Behind Isolated Trip Near the Leading Edge of the BOLT-II Configuration

The BOLT-II (Holden Mission) configuration is an extended version of the BOLT flight article and depicts hypersonic boundary-layer transition in the presence of multiple and potentially interacting instability mechanisms. Several numerical studies of the boundary-layer instabilities over these configurations have been reported in the recent literature, including our previous studies of the modal instability characteristics of boundary-layer streaks adjacent to the minor-axis symmetry plane of the BOLT configuration and the wake instabilities behind a diamond planform (“pizza-box”) trip along the symmetry plane on the secondary side of the BOLT-II configuration. The present work extends the latter study to a scaled version of the same trip that is located in the region of nonzero crossflow in the vicinity of the leading edge at X/L = 0.5. Collectively, the trips along the symmetry plane and near the leading edge are the focus of the NASA roughness experiment on the secondary side of the BOLT-II configuration. The laminar basic state computation at the nominal flight design condition of Re ∞ = 5.44 x 10 6 /m and Re ∞ = 2.5 x 10 6 /m shows that the leading-edge trip with k/δ ≈ 0.70 and planform-side-length-to-height ratio of b/k = 3.0 induces multiple asymmetric, longitudinal streaks within the trip wake. The most prominent streak among these resembles a finite amplitude crossflow vortex, and it supports the amplification of multiple families of unstable modes. The application of multi-dimensional instability analysis to the wake flow reveals that the most amplified unstable mode can achieve a peak N-factor of up to 20 by X/L = 0.80, indicating that the onset of transition is more than likely to occur within eighty percent of the model length. To the best of our knowledge, the present study represents the first analysis including nonparallel and curvature effects on hypersonic tripwake instabilities in the presence of boundary-layer crossflow over a three-dimensional configuration.

Boundary layer transition↗

DOE OSTI2025

Analyzing Trip Chaining Behavior in New York State Using 2009 and 2017 National Household Travel Survey

Trip chaining, defined as the sequential linking of trips by individuals throughout a given day, provides critical insights into daily mobility patterns and activity sequencing. Understanding these patterns has significant implications for transportation demand forecasting, congestion management, and local economic activity. This analysis examines trip chaining behaviors in New York State (NYS) for the years 2009 and 2017 and compares the Middle Atlantic Census Division with other U.S. regions in 2022, utilizing data from the National Household Travel Survey (NHTS). Through demographic, geographic, and temporal analysis, this study characterizes how populations organize travel for work, personal errands, and social activities, providing empirical evidence of evolving trip chaining behaviors to inform transportation planning strategies.

99 GENERAL AND MISCELLANEOUS↗

NASA NTRS1972

Discrete sonic jets used as boundary-layer trips at Mach numbers of 6 and 8.5

The effect of discrete three-dimensional sonic jets used to promote transition on a sharp-leading-edge flat plate at Mach numbers of 6 and 8.5 and unit Reynolds numbers as high as 2.5 x 100,000 per cm in the Langley 20-inch hypersonic tunnels is discussed. An examination of the downstream flow-field distortions associated with the discrete jets for the Mach 8.5 flow was also conducted. Jet trips are found to produce lengths of turbulent flow comparable to those obtained for spherical-roughness-element trips while significantly reducing the downstream flow distortions. A Reynolds number based upon secondary jet penetration into a supersonic main flow is used to correlate jet-trip effectiveness just as a Reynolds number based upon roughness height is used to correlate spherical-trip effectiveness. Measured heat-transfer data are in agreement with the predictions.

Stone, D. R.↗

NASA NTRS2006

Implementation of Flow Tripping Capability in the USM3D Unstructured Flow Solver

A flow tripping capability is added to an established NASA tetrahedral unstructured parallel Navier-Stokes flow solver, USM3D. The capability is based on prescribing an appropriate profile of turbulence model variables to energize the boundary layer in a plane normal to a specified trip region on the body surface. We demonstrate this approach using the k-e two-equation turbulence model of USM3D. Modification to the solution procedure primarily consists of developing a data structure to identify all unstructured tetrahedral grid cells located in the plane normal to a specified surface trip region and computing a function based on the mean flow solution to specify the modified profile of the turbulence model variables. We leverage this data structure and also show an adjunct approach that is based on enforcing a laminar flow condition on the otherwise fully turbulent flow solution in user specified region. The latter approach is applied for the solutions obtained using other one- and two-equation turbulence models of USM3D. A key ingredient of the present capability is the use of a graphical user-interface tool PREDISC to define a trip region on the body surface in an existing grid. Verification of the present modifications is demonstrated on three cases, namely, a flat plate, the RAE2822 airfoil, and the DLR F6 wing-fuselage configuration.

Pandya, Mohagna J.↗