Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TITANIUM 39”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Nuclear Data Sheets for A=39☆

Experimental nuclear structure data from various reactions and decays have been evaluated for all known nuclides of mass 39 (Mg, Al, Si, P, S, Cl, Ar, K, Ca, Sc, Ti). Detailed evaluated nuclear structure information is presented for each reaction and decay and the best values combining all available data are recommended for level energies, half-lives, γ-ray energies and intensities, decay properties (energies, intensities and placement of radiations), and other spectroscopic data. The {sup 39}K, {sup 39}Ca and {sup 39}Ar are the most extensively studied nuclides; no excited states are known in {sup 39}Mg and {sup 39}Ti. This work supersedes the earlier full evaluation of A=39 by B. Singh and J. Cameron (2006Si02).

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Processing of alnico permanent magnets by advanced directional solidification methods

Advanced directional solidification methods have been used to produce large (>15 cm length) castings of Alnico permanent magnets with highly oriented columnar microstructures. In combination with subsequent thermomagnetic and draw thermal treatment, this method was used to enable the high coercivity, high-Titanium Alnico composition of 39% Co, 29.5% Fe, 14% Ni, 7.5% Ti, 7% Al, 3% Cu (wt%) to have an intrinsic coercivity (H ci ) of 2.0 kOe, a remanence (B r ) of 10.2 kG, and an energy product (BH) max of 10.9 MGOe. These properties compare favorably to typical properties for the commercial Alnico 9. Directional solidification of higher Ti compositions yielded anisotropic columnar grained microstructures if high heat extraction rates through the mold surface of at least 200 kW/m 2 were attained. This was achieved through the use of a thin walled (5 mm thick) high thermal conductivity SiC shell mold extracted from a molten Sn bath at a withdrawal rate of at least 200 mm/h. However, higher Ti compositions did not result in further increases in magnet performance. Images of the microstructures collected by scanning electron microscopy (SEM) reveal a majority α phase with inclusions of secondary αγ phase. Transmission electron microscopy (TEM) reveals that the α phase has a spinodally decomposed microstructure of FeCo-rich needles in a NiAl-rich matrix. In the 7.5% Ti composition the diameter distribution of the FeCo needles was bimodal with the majority having diameters of approximately 50 nm with a small fraction having diameters of approximately 10 nm. The needles formed a mosaic pattern and were elongated along one <001> crystal direction (parallel to the field used during magnetic annealing). Cu precipitates were observed between the needles. Regions of abnormal spinodal morphology appeared to correlate with secondary phase precipitates. The presence of these abnormalities did not prevent the material from displaying superior magnetic properties in the 7.5% Ti composition. As a result, higher Ti compositions did not display the preferred spinodal microstructure, explaining their inferior magnetic properties.

36 MATERIALS SCIENCE↗

ORNL Resolved Resonance Covariance Generation for ENDF/B-VII.1

Resonance-parameter covariance matrix (RPCM) evaluations in the resolved resonance regionwere done at the Oak Ridge National Laboratory (ORNL) for the chromium isotopes, titanium isotopes, {sup 19}F, {sup 58}Ni, {sup 60}Ni, {sup 35}Cl, {sup 37}Cl, {sup 39}K, {sup 41}K, {sup 55}Mn, {sup 233}U, {sup 235}U, {sup 238}U, and {sup 239}Pu using the computer code SAMMY. The retroactive approach of the code SAMMY was used to generate the RPCMs for {sup 233}U. For {sup 235}U, the approach used for covariance generation was similar to the retroactive approach with the distinction that real experimental data were used as opposed to data generated from the resonance parameters. RPCMs for {sup 238}U and {sup 239}Pu were generated together with the resonance parameter evaluations. The RPCMs were then converted in the ENDF format using the FILE32 representation. Alternatively, for computer storage reasons, the FILE32 was converted in the FILE33 cross section covariance matrix (CSCM). Both representations were processed using the computer code PUFF-IV. This paper describes the procedures used to generate the RPCM and CSCM in the resonance region for ENDF/B-VII.1. The impact of data uncertainty in nuclear reactor benchmark calculations is also presented.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Site selective substitution Pt for Ti in KTiOPO{sub 4}:Ga crystals revealed by electron paramagnetic resonance

Electron Paramagnetic Resonance at low temperatures has been used to characterize potassium titanyl phosphate (KTiOPO{sub 4}) single crystals grown by different techniques. Irradiation with 20 MeV electrons performed at room temperature and liquid nitrogen temperature caused an appearance of electrons and holes. Platinum impurities act as electron traps in KTiOPO{sub 4} creating Pt{sup 3+} centers. Two different Pt{sup 3+} centers were observed, Pt(A) and Pt(D). The Pt(A) centers are dominant in undoped samples, whereas Pt(D)—in Ga-doped KTP crystals. Superhyperfine structure registered for Pt(D) centers was attributed to interactions of platinum electrons with {sup 39}K and two {sup 31}P nuclei in their surroundings. In both Pt(A) and Pt(D) centers, Pt{sup 3+} ions substitute for Ti{sup 4+} ions, but with a preference to one of two electrically distinct crystallographic positions. The site selective substitution can be controlled by the Ga-doping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Selective oxide-forming alloy, coating formed from and machine component including same

A selective oxide-forming alloy, a coating formed from, and a machine component including the coating are provided. The selective oxide-forming alloy includes between atomic percent and 26 atomic percent silicon (Si), between 21 atomic percent and 27 atomic percent titanium (Ti), between 30 atomic percent and 39 atomic percent aluminum (Al), between 2 atomic percent and 10 atomic percent hafnium (Hf), and a balance of niobium (Nb).

Holgate, Collin Scott↗

Measuring the energy flux at the substrate position during magnetron sputter deposition processes

In this work, the energetic conditions at the substrate were investigated in dc magnetron sputtering (DCMS), pulsed dc magnetron sputtering (pDCMS), and high power impulse magnetron sputtering (HiPIMS) discharges by means of an energy flux diagnostic based on a thermopile sensor, the probe being set at the substrate position. Measurements were performed in front of a titanium target for a highly unbalanced magnetic field configuration. The average power was always kept to 400 W and the probe was at the floating potential. Variation of the energy flux against the pulse peak power in HiPIMS was first investigated. It was demonstrated that the energy per deposited titanium atom is the highest for short pulses (5 {mu}s) high pulse peak power (39 kW), as in this case, the ion production is efficient and the deposition rate is reduced by self-sputtering. As the argon pressure is increased, the energy deposition is reduced as the probability of scattering in the gas phase is increased. In the case of the HiPIMS discharge run at moderate peak power density (10 kW), the energy per deposited atom was found to be lower than the one measured for DCMS and pDCMS discharges. In these conditions, the HiPIMS discharge could be characterized as soft and close to a pulsed DCMS discharge run at very low duty cycle. For the sake of comparison, measurements were also carried out in DCMS mode with a balanced magnetron cathode, in the same working conditions of pressure and power. The energy flux at the substrate is significantly increased as the discharge is generated in an unbalanced field.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Emittance characterization of a hot-cavity laser ion source at Holifield Radioactive Ion Beam Facility

The first investigation of the transverse emittance of a hot-cavity laser ion source based on all-solid-state Ti:sapphire lasers is presented. The emittances of {sup 63}Cu ion beams generated by three-photon resonant ionization are measured and compared with that of the {sup 69}Ga and {sup 39}K ion beams resulting from surface ionization in the same ion source. A self-consistent unbiased elliptical exclusion method is adapted for noise reduction and emittance analysis. Typical values of the rms and 90% fractional emittances of the Cu ion beams at 20 keV energy are found to be about 2 and 8 {pi} mm mrad, respectively, for the ion currents of 2-40 nA investigated. The emittances of the laser-produced Cu ion beams are smaller than those of the surface-ionized Ga and K ion beams.

43 PARTICLE ACCELERATORS↗

Supported Oxygen Evolution Catalysts by Design: Toward Lower Precious Metal Loading and Improved Conductivity in Proton Exchange Membrane Water Electrolyzers

Reducing the precious metal content of water oxidation catalysts for proton-exchange-membrane water electrolyzers remains a critical barrier to their large-scale deployment. Herein, we present an engineered architecture for supported iridium catalysts, which enables decreased precious metal content and improved activity and conductivity. The improvement in performance at lower precious metal loading is realized by the deposition of a conformal layer of platinum nanoparticles on titanium dioxide (TiO 2 ) using a facile photoreduction method to prepare conductive layer coated supports (CCSs). Platinum nanoparticles are homogeneously dispersed on TiO 2 , and the conductivity of the subsequent catalysts with 39 wt % precious group metal loadings is significantly higher than the commercial 75 wt % loaded IrO 2 -TiO 2 catalysts. The conformal conductive layer also maintains an enhanced conductivity and electrochemical activity upon thermal annealing when compared to catalysts without the conductive layer and nonconformal heterogeneous conductive layer. The iridium mass activity from half-cell studies shows a 141% improvement for CCS supported catalysts at 42% lower loadings compared to the commercial catalysts. The conductive layer also improves the single cell electrolyzer performance at a similar catalyst loading in comparison to a commercial state-of-the-art catalyst. Here, we correlate the physical properties of the engineered catalysts with their electrochemical performance in electrolyzers to understand structure-activity relationships, and we anticipate further performance improvements upon synthesis and materials optimizations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural chemistry and spin-glass behaviour of Nd{sub 18}Li{sub 8}Fe{sub 4}TiO{sub 39}

Nd{sub 18}Li{sub 8}Fe{sub 4}TiO{sub 39} has been synthesised and characterised by neutron powder diffraction, X-ray absorption spectroscopy, Moessbauer spectroscopy and magnetometry. The cubic structure (Pm3-bar n, a=11.97227(8) A) is based on intersecting Left-Pointing-Angle-Bracket 1 1 1 Right-Pointing-Angle-Bracket chains comprised of alternating octahedral and trigonal-prismatic coordination sites. These chains lie within hexagonal-prismatic cavities formed by a Nd-O framework. The larger of the two crystallographically distinct octahedral sites, 8e, is occupied by iron, titanium and lithium in a ratio of 76:20:4; the smaller, 2a, is occupied by iron and titanium in a ratio of 79:21. The trigonal-prismatic site, 16i, is occupied by lithium and iron in a ratio of 98:2. The cations on the 2a sites are assigned as Ti{sup 4+}and low-spin Fe{sup 4+}, and those on the 16i sites as Li{sup +} and Fe{sup 3+}. The 8e sites are thought to be occupied by Li{sup +}, Fe{sup 3+} and Ti{sup 3+}. Nd{sub 18}Li{sub 8}Fe{sub 4}TiO{sub 39} undergoes a transition to a spin-glass state at 4.25(5) K. - Graphical abstract: Nd{sub 18}Li{sub 8}Fe{sub 4}TiO{sub 39} undergoes a transition to a spin-glass state at 4.25(5) K. Highlights: Black-Right-Pointing-Pointer Spin-glass behaviour in Nd{sub 18}Li{sub 8}Fe{sub 4}TiO{sub 39} below 4.25 K. Black-Right-Pointing-Pointer Application of X-ray absorption spectroscopy to a complex mixed-metal oxide. Black-Right-Pointing-Pointer Mixed-valence cations in Nd{sub 18}Li{sub 8}Fe{sub 4}TiO{sub 39}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-precision {beta} decay half-life measurements of proton-rich nuclei for testing the CVC hypothesis

The experimental study of super-allowed nuclear {beta} decays serves as a sensitive probe of the conservation of the weak vector current (CVC) and allows tight limits to be set on the presence of scalar or right-handed currents. Once CVC is verified, it is possible to determine the V{sub ud} element of the CKM quark-mixing matrix. Similarly, the study of nuclear mirror {beta} decays allows to arrive at the same final quantity V{sub ud}. Whereas dedicated studies of 0{sup +}{yields}0{sup +} decays are performed for several decades now, the potential of mirror transitions was only rediscovered recently. Therefore, it can be expected that important progress is possible with high-precision studies of different mirror {beta} decays. In the present piece of work the half-life measurements performed by the CENBG group of the proton-rich nuclei {sup 42}Ti, {sup 38-39}Ca, {sup 30-31}S and {sup 29}P are summarised.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Ab initio molecular dynamics simulations of low energy recoil events in ceramics

The recent progress in the use of large-scale ab initio molecular dynamics (AIMD) to investigate low energy recoil events and determine threshold displacement energies, Ed, in ceramics is reviewed. In general, Ed shows a significant dependence on recoil direction and atom. In 3C-SiC, the minimum Ed for both C and Si atoms is found along the <100> direction, with a value of 20 and 49 eV, respectively. The results demonstrate that significant charge transfer occurs during the dynamics process, and defects can enhance charge transfer to surrounding atoms, which provides important insights into the formation of charged defects. It is found that the C vacancy is a positively charged defect, whereas the Si vacancy is in its neutral state. The minimum Ed in GaN is determined to be 17 and 39 eV for N and Ga atoms, respectively, both along the direction. The average Ed for N atoms (32.4 eV) is smaller than that for Ga atoms (73.2 eV). It is of interest to note that the N defects created along different crystallographic directions have a similar configuration (a N-N dumbbell configuration), but various configurations for Ga defects are formed. In Y2Ti2O7 prochlore, the minimum Ed for Y atoms is determined to be 27 eV for a recoil along the <100> direction, 31.5 eV for Ti atoms along the <100> direction, 14.5 eV for O48f atoms along the <110> direction and 13 eV for O8b atoms along the <111> direction. The average Ed values determined are 32.7, 34.2, 14.2 and 16.1 eV for yttrium, titanium, O48f and O8b atoms, respectively. Cation interstitials at vacant 8a sites, which are generally occupied by oxygen anions, and at the bridge sites between two neighboring cations along the <010> direction are observed after low energy recoil events.

Ab initio MD↗

Synthesis and structural chemistry of La{sub 18}Li{sub 8}Rh{sub 4}MO{sub 39} (M=Ti, Mn, Ru)

Polycrystalline samples of La{sub 18}Li{sub 8}Rh{sub 4}MO{sub 39} (M=Ti, Mn, Ru) have been prepared by a solid-state method and studied by neutron powder diffraction. They are isostructural with La{sub 18}Li{sub 8}Rh{sub 5}O{sub 39} and adopt the cubic space group Pm3{sup -bar }n with a {approx}12.22 A. Their structure consists of a La-O framework containing intersecting channels that run along <111>. These channels are occupied by chains made up of alternating, face-sharing trigonal-prismatic and octahedral coordination polyhedra; there are two crystallographically distinct types of octahedral site. The prisms are occupied by Li and the transition metals are disordered over the two octahedral sites. - Graphical abstract: The substitution of Ti, Mn or Ru into La{sub 18}Li{sub 8}Rh{sub 5}O{sub 39} results in the loss of the cation ordering seen in the parent compound.

36 MATERIALS SCIENCE↗

The first allwise proper motion discovery: Wisea J070720.50+170532.7

While quality checking a new motion-aware co-addition of all 12.5 months of Wide-field Infrared Survey Explorer (WISE) data, we found that the source WISE J070720.48+170533.0 moved 0.''9 in six months. Backtracking this motion allowed us to identify this source as 2MASS J07071961+1705464, with several entries in the USNO B catalog. An astrometric fit to these archival data gives a proper motion of μ = 1793 ± 2 mas yr{sup –1} and a parallax of piv = 35 ± 42 mas. Photometry from WISE, 2MASS, and the POSS can be fit reasonably well by a blackbody with T = 3658 K and an angular radius of 4.36 × 10{sup –11} radians. No clear evidence of H{sub 2} collision-induced absorption is seen in the near-infrared. An optical spectrum shows broad deep CaH bands at 638 and 690 nm, broad deep Na D at 598.2 nm, and weak or absent TiO, indicating that this source is an ultra-subdwarf M star with a radial velocity v {sub rad} ≈ –21 ± 18 km s{sup –1} relative to the Sun. Given its apparent magnitude, the distance is about 39 ± 9 pc and the tangential velocity is probably ≈330 km s{sup –1}, but a more precise parallax is needed to be certain.

79 ASTRONOMY AND ASTROPHYSICS↗

Electron/phonon coupling in group-IV transition-metal and rare-earth nitrides

Transport electron/phonon coupling parameters and Eliashberg spectral functions α{sub tr}{sup 2}F(ℏω) are determined for group-IV transition-metal (TM) nitrides TiN, ZrN, and HfN, and the rare-earth (RE) nitride CeN using an inversion procedure based upon temperature-dependent (4 < T < 300 K) resistivity measurements of high-crystalline-quality stoichiometric epitaxial films grown on MgO(001) by magnetically-unbalanced reactive magnetron sputtering. Transport electron/phonon coupling parameters λ{sub tr} vary from 1.11 for ZrN to 0.82 for HfN, 0.73 for TiN, and 0.44 for CeN. The small variation in λ{sub tr} among the TM nitrides and the weak coupling in CeN are consistent with measured superconducting transition temperatures 10.4 (ZrN), 9.18 (HfN), 5.35 (TiN), and <4 K for CeN. The Eliashberg spectral function describes the strength and energy spectrum of electron/phonon coupling in conventional superconductors. Spectral peaks in α{sup 2}F(ℏω), corresponding to regions in energy-space for which electrons couple to acoustic ℏω{sub ac} and optical ℏω{sub op} phonon modes, are centered at ℏω{sub ac} = 33 and ℏω{sub op} = 57 meV for TiN, 25 and 60 meV for ZrN, 18 and 64 meV for HfN, and 21 and 39 meV for CeN. The acoustic modes soften with increasing cation mass; optical mode energies remain approximately constant for the TM nitrides, but are significantly lower for the RE nitride due to a lower interatomic force constant. Optical/acoustic peak-intensity ratios are 1.15 ± 0.1 for all four nitrides, indicating similar electron/phonon coupling strengths α{sub tr}(ℏω) for both modes.

36 MATERIALS SCIENCE↗

Microstructure and Friction-Wear Behavior of Multi-arc Ion Plating TiAlNC Ceramic Coating on WC-6%Co Substrate

Nanocomposite coating could be used for machining tools, which can be used for cutting, drilling, milling, whetting, profiling, honing and superfinishing of various materials with high productivity. In this work, the TiAlNC ceramic coating was prepared by multi-arc ion plating method on WC-6%Co substrate. The microstructure and morphology of the coating were observed by scanning electron microscopy and transmission electron microscopy. The phase and chemical composition of the coating were determined by x-ray diffraction and x-ray energy-dispersive spectroscopy, respectively. The adhesive force of the coating was measured by a scratch tester, at the same time the friction-wear behavior of the coating was studied. The results show that there were TiN and (Ti,Al)(N,C) two phases, and there was the coexistence of amorphous and nanocrystalline in the coating. The chemical composition of the coating was composed of 20 ± 9 at.% Ti, 16 ± 5 at.% Al, 39 ± 5 at.% N and 25 ± 10 at.% C. The thickness of the coating was about 4.5 μm. The average root mean square value of the surface roughness was 225 ± 16 nm. A critical force for coating failure in scratch testing was about 25 N. The friction coefficients of the substrate and the coating were 0.55 and 0.35, respectively. The ceramic coating could improve the wear resistance of the substrate.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Growth and characterization of TiAlN/CrAlN superlattices prepared by reactive direct current magnetron sputtering

TiAlN and CrAlN coatings were prepared using a reactive direct current magnetron sputtering system from TiAl and CrAl targets. Structural characterization of the coatings using x-ray diffraction (XRD) revealed the B1 NaCl structure of TiAlN and CrAlN coatings with a prominent reflection along the (111) plane. The XPS data confirmed the bonding structures of TiAlN and CrAlN single layer coatings. Subsequently, nanolayered multilayer coatings of TiAlN/CrAlN were deposited on silicon and mild steel (MS) substrates at different modulation wavelengths ({lambda}) with a total thickness of approximately 1.0 {mu}m. The modulation wavelengths were calculated from the x-ray reflectivity data using modified Bragg's law. TiAlN/CrAlN multilayer coatings were textured along (111) for {lambda}<200 A and the XRD patterns showed the formation of superlattice structure for coatings deposited at {lambda}=102 A. The x-ray reflectivity data showed reflections of fifth and seventh orders for multilayer coatings deposited at {lambda}=102 and 138 A, respectively, indicating the formation of sharp interfaces between TiAlN and CrAlN layers. The cross-sectional scanning electron microscopy image of TiAlN/CrAlN multilayer coatings indicated a noncolumnar and dense microstructure. A maximum hardness of 39 GPa was observed for TiAlN/CrAlN multilayer coatings deposited at {lambda}=93 A, which was higher than the rule-of-mixture value (30 GPa) for TiAlN and CrAlN. Study of thermal stability of the coatings in air using micro-Raman spectroscopy indicated that the TiAlN/CrAlN multilayer coatings were stable up to 900 deg. C in air. TiAlN/CrAlN multilayer coatings also exhibited improved corrosion resistance when compared to the MS substrate.

36 MATERIALS SCIENCE↗

Visible light absorption of TiO{sub 2} materials impregnated with tungstophosphoric acid ethanol–aqueous solution at different pH values. Evidence about the formation of a surface complex between Keggin anion and TiO{sub 2} surfaces

Graphical abstract: - Highlights: • TPA impregnation on TiO{sub 2} particles was done at different initial pH values. • Powders characterization evidenced the possible existence of TPA–TiO{sub 2} complexes. • Keggin anion complexed on TiO{sub 2} would be responsible of visible light absorption. - Abstract: TiO{sub 2} particles prepared by the sol–gel method were impregnated at different pH values (1.0, 2.0, 5.0 and 10.0) with a water–ethanol solution (50% V/V) of tungstophosphoric acid (TPA) (0.012 M). Similar preparation was carried out to synthesize TiO{sub 2} impregnated with [WO{sub 4}]{sup 2−} (TiW). These materials were characterized by different techniques such as UV–vis diffuse reflectance spectroscopy (UV–vis DRS), magic angle spinning nuclear magnetic resonance of {sup 31}P ({sup 31}P MAS NMR), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Fourier transform Raman spectroscopy (FT-Raman). Results revealed that TPA–TiO{sub 2} materials exhibit visible light absorption only when impregnation was done at pH 1.0 (TiTPA1) and 2.0 (TiTPA2). TiW powder did not show visible light absorption. XRD patterns show the presence of peaks at 2θ = 25.4° (1 0 1), 37.9° (0 0 4), 47.8° (2 0 0) and 54.3° associated to the anatase phase. Solid NMR, FT-IR and FT-Raman characterization showed that TiTPA1 and TiTPA2 samples contain Keggin ([PW{sub 12}O{sub 40}]{sup 3−}) and lacunary anions ([PW{sub 11}O{sub 39}]{sup 7−}) respectively. On the other hand, FT-Raman results revealed a blue shifting and broadening of the band at 141 cm{sup −1} corresponding to anatase TiO{sub 2} and moreover, a broadening of bands at 900–1100 cm{sup −1} attributed to Keggin structures of TPA. Both spectral changes could be related to the formation of a surface complex between the Keggin anion of TPA and TiO{sub 2} surfaces. This interaction should be responsible for visible light absorption.

36 MATERIALS SCIENCE↗

The solubility of titanite in silicate melt determined from growth and dissolution experiments

The solubility of titanite (CaTiSiO 5 ) in Si-rich melts was measured experimentally through growth experiments at 800–1000 °C, 0.5–1.0 GPa, log fO 2 ~ CCO–0.8, t = 72–168 h, and H 2 O = 0 to 4 wt.%, and in dissolution experiments at 925–1300 °C, 0.8 GPa, t = 18–118 h, and H 2 O = 1–10 wt.% in a piston-cylinder apparatus. Run product glasses in growth experiments were homogeneous, and iron loss suppressed ilmenite crystallization. Saturation concentrations in dissolution experiments were estimated by fitting measured diffusion profiles. Titanite solubility increases with increasing temperature and melt composition parameter \(M = {\text{ molar }}\left( {{\text{Na }} + {\text{ K }} + {\text{ 2Ca}}} \right)/\left( {{\text{Al }} \times {\text{ Si}}} \right)\) . Multiple linear regression of glass composition data from growth and dissolution experiments ( n = 29) plus 39 experiments from the LEPR database (Hirschmann et al. 2008 ) yielded the titanite solubility equation (adj. r 2 = 0.95): \(\left( {TiO_{2} } \right)^{melt} \left( {wt.\% } \right) = 0.978 \times M + 0.0048 \times T\left( K \right){-}5.90\) . This model correctly predicted undersaturation in 95% of 2344 experiments from the LEPR database that did not have titanite or rutile. Application to natural rocks yields saturation temperatures that are similar to independent temperature estimates. Finally, this equation should be useful for constraining the temperatures of titanite-saturated melts, for determining whether titanite saturation in magmatic source regions is likely, and for determining when titanite can crystallize and begin to exert an influence on melt geochemistry.

58 GEOSCIENCES↗