Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Substrate preheating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Optimal Substrate Preheating Model for Thermal Spray Deposition of Thermosets onto Polymer Matrix Composites

High velocity oxy-fuel (HVOF) sprayed, functionally graded polyimide/WC-Co composite coatings on polymer matrix composites (PMC's) are being investigated for applications in turbine engine technologies. This requires that the polyimide, used as the matrix material, be fully crosslinked during deposition in order to maximize its engineering properties. The rapid heating and cooling nature of the HVOF spray process and the high heat flux through the coating into the substrate typically do not allow sufficient time at temperature for curing of the thermoset. It was hypothesized that external substrate preheating might enhance the deposition behavior and curing reaction during the thermal spraying of polyimide thermosets. A simple analytical process model for the deposition of thermosetting polyimide onto polymer matrix composites by HVOF thermal spray technology has been developed. The model incorporates various heat transfer mechanisms and enables surface temperature profiles of the coating to be simulated, primarily as a function of substrate preheating temperature. Four cases were modeled: (i) no substrate preheating; (ii) substrates electrically preheated from the rear; (iii) substrates preheated by hot air from the front face; and (iv) substrates electrically preheated from the rear and by hot air from the front.

Ivosevic, M.↗
DOE OSTI2026

Microstructural evolution, defect mitigation, and precipitation behavior in AA6061 via laser powder bed fusion with high-temperature substrate heating

Defects, particularly solidification cracking, remain persistent challenges in the laser powder bed fusion (LPBF) processing of AA6061 aluminum alloy. This study systematically investigates defect mitigation, microstructural evolution, and mechanical properties associated with high-temperature substrate preheating at 500 °C. Comprehensive microstructural analyses, including characterization of defects, grain structures, and precipitation behavior, were performed on samples in both as-built and T6 heat-treated states. Elevated preheating substantially reduced solidification cracking across a wide processing window, while demonstrating decreased crack sensitivity to laser parameters. Columnar cracks along the build direction were observed despite substrate preheating. Lack-of-fusion and keyhole porosity were effectively eliminated, though gas-induced microporosity persisted at higher powers. In-depth characterization of two distinct laser power and speed conditions confirmed the formation of micron-sized, non-coherent Mg 2 Si precipitates under heated substrate conditions, alongside α-AlFeCrMnSi intermetallic phases indicative of in-situ thermal effects during fabrication. Subsequent T6 heat treatment revealed the formation of fine, coherent needle-shaped β″ strengthening precipitates. Despite substantial differences in processing parameters, comparable mechanical properties were measured in the as-built samples (∼52 MPa yield strength, ∼130 MPa tensile strength), primarily due to reduced strain hardening effects and consistent precipitation characteristics. Meanwhile, the T6 heat treatment led to significant improvement in properties, enhancing yield strength by over 400%, aligning closely with the performance of conventional wrought AA6061-T6. These findings underscore that high-temperature substrate preheating offers an effective means to suppress cracks, control precipitation, and enhance mechanical performance in LPBF-processed AA6061.

36 MATERIALS SCIENCE↗
NASA NTRS2018

Preparation of Thick NI/AL Reactive Multilayer Films and Prospective Use for Self-Powered Brazing of TI-6AL-4V

In this study we demonstrate a new method for depositing thick reactive multilayer films (RMFs) (thickness > 14 µm) by using Ti interlayer integration and substrate preheating during fabrication. These two adjustments are designed to alleviate internal planar stresses that cause delamination between deposited layers and peeling off the substrate. Decreasing the distance between Ti interlayers helps to eliminate delamination between deposited layers. Through high speed camera measurements, the reaction propagation speed of an RMF sample with preheating is 42% slower than the same RMF that was not preheated, indicating a slower heat release rate. The preliminary experiments on brazing Ti-6Al-4V coated with BAlSi-4 brazing material revealed dendritic structure branching out from the RMF surface into the brazing material. The dendrite structures most likely form because of rapid melting and solidification of the brazing material. However, this rapid melting and solidification cycle does not appear to occur uniformly across the BAlSi-4RMF interface which is linked to its low bonding strength. When the Ti-6Al-4V substrate is heated to 150 °C prior to ignition, the strength increases to 0.47 MPa when the total RMF thickness is 84 µm and 15 MPa of pressure is applied.

Cheng, Jinquan↗
NASA NTRS2023

Hot Cracking Behavior and Beam-Induced Grain Refinement in Electron Beam Freeform Fabricated Al 7075

Electron beam freeform fabrication (EBF 3 ) is a high deposition rate, wire-based directed energy deposition (DED) additive manufacturing (AM) process used to print metallic parts in a vacuum environment. While high specific strength 7xxx-series Al alloys are of interest in the aerospace and automotive industries, these alloys suffer from hot cracking issues during fusion welding and AM. In this work, linear deposits of Al 7075 were fabricated with EBF 3 to study the effects of baseplate thickness, preheat temperature, and beam focus on hot cracking behavior. Solidification cracks were observed in the first deposition layer, and by the third layer coalesced into large “macrocracks” running vertically through the build height. Fine, intergranular liquation “microcracks” appeared between macrocracks below the root of the final deposit layer fusion zone. Increasing the substrate preheat temperature from 165°C to 320°C deepened the partially melted zone and resulted in a more than twofold increase in the liquation microcrack density. Analysis of Scheil solidification diagrams revealed that fugitive losses of Zn and Mg during deposition increased the susceptibility to solidification cracking and promoted substrate liquation cracking. Focused electron beam (EB) conditions combined with a high aspect ratio elliptical raster pattern resulted in bands of refined, equiaxed grains. The refined microstructure suppressed solidification macrocracking and caused a nearly fivefold reduction in liquation crack density, demonstrating that beam-induced grain refinement may be a promising low-cost method for reducing hot cracking during AM.

aluminum↗
NASA NTRS2016

Advanced in In Situ Inspection of Automated Fiber Placement Systems

Automated Fiber Placement (AFP) systems have been developed to help take advantage of the tailorability of composite structures in aerospace applications. AFP systems allow the repeatable placement of uncured, spool fed, preimpregnated carbon fiber tape (tows) onto substrates in desired thicknesses and orientations. This automated process can incur defects, such as overlapping tow lines, which can severely undermine the structural integrity of the part. Current defect detection and abatement methods are very labor intensive, and still mostly rely on human manual inspection. Proposed is a thermographic in situ inspection technique which monitors tow placement with an on board thermal camera using the preheated substrate as a through transmission heat source. An investigation of the concept is conducted, and preliminary laboratory results are presented. Also included will be a brief overview of other emerging technologies that tackle the same issue. Keywords: Automated Fiber Placement, Manufacturing defects, Thermography

Juarez, Peter D.↗
DOE OSTI2022

Hot-Casting-Assisted Liquid Additive Engineering for Efficient and Stable Perovskite Solar Cells

High-performance inorganic–organic lead halide perovskite solar cells (PSCs) are often fabricated with a liquid additive such as dimethyl sulfoxide (DMSO), which retards crystallization and reduces roughness and pinholes in the perovskite layers. However, DMSO can be trapped during perovskite film formation and induce voids and undesired reaction byproducts upon later processing steps. Here, it is shown that the amount of residual DMSO can be reduced in as-spin-coated films significantly through use of preheated substrates, or a so-called hot-casting method. Hot casting increases the perovskite film thickness given the same concentration of solutions, which allows for reducing the perovskite solution concentration. By reducing the amount of DMSO in proportion to the concentration of perovskite precursors and using hot casting, it is possible to fabricate perovskite layers with improved perovskite–substrate interfaces by suppressing the formation of byproducts, which increase trap density and accelerate degradation of the perovskite layers. The best-performing PSCs exhibit a power conversion efficiency (PCE) of 23.4% (23.0% stabilized efficiency) under simulated solar illumination. Furthermore, encapsulated devices show considerably reduced post-burn-in decay, retaining 75% and 90% of their initial and post-burn-in efficiencies after 3000 h of operation with maximum power point tracking (MPPT) under high power of ultraviolet (UV)-containing continuous light exposure.

perovskite-substrate interface↗
DOE OSTI2022

Impact of processing conditions on the film formation of lead-free halide double perovskite Cs 2 AgBiBr 6

Lead-free halide double perovskites with enhanced stability have gained attention as a promising environmentally friendly alternative to lead-based halide perovskites. Amongst different halide double perovskites, Cs 2 AgBiBr 6 has shown attractive optoelectronic properties and stability, making it a promising candidate for stable high-efficiency optoelectronic devices. Motivated by a data mining effort, we present here in this study the effects of different processing strategies on the microstructure and thin-film formation dynamics of Cs 2 AgBiBr 6 . We apply some of the most successfully used solvent engineering approaches from the halide perovskite research to halide double perovskites, namely antisolvent- and additive-assisted synthesis. Using in situ spectroscopy and diffraction, the film formation of Cs 2 AgBiBr 6 is investigated during spin coating, and the subsequent post-deposition thermal annealing. Dropping antisolvents during spin coating induces immediate supersaturation and crystallization of the wet film, whereas the time of dropping the antisolvent has implications on the film formation dynamics and the final microstructure. For additive (HBr)-assisted synthesis, we show how the addition of HBr affects colloid formation in solution and thus influences the crystallization pathway during thin-film processing. Finally, HBr additive simplifies synthesis in that it doesn't require solution and substrate preheating to obtain pinhole-free films even with higher thickness.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2003

Microstructure and Properties of Thermally Sprayed Functionally Graded Coatings for Polymeric Substrates

The use of polymer matrix composites (PMCs) in the gas flow path of advanced turbine engines offers significant benefits for aircraft engine performance but their useful lifetime is limited by their poor erosion resistance. High velocity oxy-fuel (HVOF) sprayed polymer/cermet functionally graded (FGM) coatings are being investigated as a method to address this technology gap by providing erosion and oxidation protection to polymer matrix composites. The FGM coating structures are based on a polyimide matrix filled with varying volume fractions of WC-Co. The graded coating architecture was produced using a combination of internal and external feedstock injection, via two computer-controlled powder feeders and controlled substrate preheating. Porosity, coating thickness and volume fraction of the WC-Co filler retained in the coatings were determined using standard metallographic techniques and computer image analysis. The pull-off strength (often referred to as the adhesive strength) of the coatings was evaluated according to the ASTM D 4541 standard test method, which measured the greatest normal tensile force that the coating could withstand. Adhesive/cohesive strengths were determined for three different types of coating structures and compared based on the maximum indicated load and the surface area loaded. The nature and locus of the fractures were characterized according to the percent of adhesive and/or cohesive failure, and the tested interfaces and layers involved were analyzed by Scanning Electron Microscopy.

Ivosevic, M.↗
DOE OSTI2025

Crack mitigation and wear performance of high-strength steel coatings deposited by high-speed laser cladding

This article investigates the fabrication of defect-free Rockit® 606, a high‑carbon, vanadium- and chromium-enriched precipitation-hardening martensitic steel coating, using high-speed laser cladding (HSLC). Compared to conventional laser cladding, HSLC offers higher deposition efficiency, improved coating quality, minimal thermal distortion, and a reduced heat-affected zone. Various HSLC parameters—including laser power, travel speed, powder feed rate, and overlap distance—were optimized to achieve superior coating properties. Microstructural analysis revealed solidification cracks in coatings deposited on carburized steel, regardless of processing parameters. However, preheating the substrate to 250 °C effectively eliminated cracking by reducing thermal gradients. The coatings exhibited a columnar dendritic microstructure, with coarser dendrites near the substrate and finer dendrites towards the surface. Hardness measurements confirmed that all coatings significantly exceeded the industry-specified threshold of 60 HRC, with preheating having minimal effect on overall hardness distribution. Reciprocating sliding wear tests demonstrated a substantial improvement in wear resistance for the defect-free HSLC coatings compared to baseline carburized steel. These findings underscore the potential of HSLC for producing high-performance, wear-resistant coatings suitable for industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dependence of Uranium Oxide Polymorphism on Plasma Synthesis Conditions

Here, we synthesized uranium oxide nanoparticles using a plasma flow reactor (PFR) and studied the effects of three different experimental parameters on the resulting morphologies and speciation of the particles: (1) collection duration, (2) collection substrate temperature, and (3) radial collection position due to radial temperature gradients in the PFR. We also induced three distinct temperature histories along the axis of the plasma flow reactor by varying the gas flow rates downstream of the plasma torch. Transmission electron microscopy (TEM) analyses of collected particles showed two phases of uranium oxides (fcc-UO 2 and α-UO 3 ). The chemical compositions of the resulting uranium oxide particles were not altered by the three parameters investigated in this work but varied based on the temperature history induced. Preheating of the collection substrate led to deposition of fewer particles, which is attributed to a reduction in thermophoretic force caused by the reduced temperature gradient for preheated substrates. The relative amounts of UO 2 to UO 3 and particle size varied depending on the cooling history employed during synthesis.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
NASA NTRS2001

Processing and Testing of Thermoplastic Composite Cylindrical Shells Fabricated by Automated Fiber Placement

Two 61-cm-diameter eight-ply quasi-isotropic IM7/PEEK cylindrical shells were fabricated by automated fiber placement the NASA Langley Research Center using only infrared radiant heat to preheat the substrate and incoming composite uni-tape. The shells were characterized by ultrasonic c-scans for overall consolidation quality, and by optical microscopy and acid digestion for void content. Compression tests were also performed. Although the material used in the study was of generally poor quality due to numerous splits and dry fiber regions, the process was able to achieve a net reduction in void content in the as-placed component. Microscopy of the composite shells revealed well-consolidated, void-free interfaces. The two cylinders were then tested in uni-axial compression in a 1334 kN-capacity hydraulic test machine until buckling occurred. A geometrically nonlinear finite element analysis was conducted, and the differences between the predicted and measured values were 18.0 and 25.8%, respectively. Inclusion of measured imperfections of the cylinder into the analysis is expected to reduce these differences.

Hulcher, Anthony Bruce↗
DOE OSTI2024

System and method for large-area pulsed laser melting of metallic powder in a laser powder bed fusion application

The present disclosure relates to systems and methods for performing large area laser powder bed fusion (LBPF) to form a plurality of layers of a 3D part in a layer-by-layer fashion using meltable powder particles. In one implementation the system makes use of a first light source, which may be a diode laser subsystem, for generating a first light pulse of a first duration. The first light is used to preheat a substrate underneath a new layer of powder particles, wherein the substrate is formed from a previously fused quantity of the powder particles. A second light source, which may be a pulse laser, generates a second light pulse subsequent to the first light pulse. The second light pulse has a second duration shorter than the first duration by a factor of at least about 10, and fully melts the new layer of powder particles in addition to the substrate, to achieve a smooth printed layer. The wavelength of the first light pulse also differs from a wavelength of the second light pulse.

Khairallah, Saad A.↗
NASA NTRS1964

Fuel Retention Improvement at High Temperatures in Tungsten-Uranium Dioxide Dispersion Fuel Elements by Plasma-Spray Cladding

An investigation was undertaken to determine the feasibility of depositing integrally bonded plasma-sprayed tungsten coatings onto 80-volume-percent tungsten - 20-volume-percent uranium dioxide composites. These composites were face clad with thin tungsten foil to inhibit uranium dioxide loss at elevated temperatures, but loss at the unclad edges was still significant. By preheating the composite substrates to approximately 3700 degrees F in a nitrogen environment, metallurgically bonded tungsten coatings could be obtained directly by plasma spraying. Furthermore, even though these coatings were thin and somewhat porous, they greatly inhibited the loss of uranium dioxide. For example, a specimen that was face clad but had no edge cladding lost 5.8 percent uranium dioxide after 2 hours at 4750 dgrees F in flowing hydrogen. A similar specimen with plasma-spray-coated edges, however, lost only 0.75 percent uranium dioxide under the same testing conditions.

Grisaffe, Salvatore J.↗
DOE OSTI2020

Controlling substrate temperature with infrared heating to improve mechanical properties of large-scale printed parts

Additively manufactured parts made with polymer extrusion techniques can be 50-75% weaker in the z-direction (across layers) than in the x- and y-directions. This has been attributed to poor mobility of polymer chains and a low degree of entanglement across a cold deposition interface. This is particularly a challenge when printing large-scale parts, such as with the Big Area Additive Manufacturing (BAAM) system, because layer times can exceed several minutes. The current work presents a method for controlling the temperature of the substrate material on the BAAM just prior to deposition using infrared heating lamps. Additionally, long layer times were simulated by actively cooling the material following deposition of each layer. The effect of substrate temperature on the z-direction mechanical properties of 20% carbon fiber reinforced acrylonitrile butadiene styrene (ABS) was measured for an initial temperature ranging from 50 °C to 150 °C and a preheated temperature ranging from 150 °C to 220 °C. Infrared preheating proved to be very effective when applied to substrates that had cooled considerably, almost doubling the tensile strength and increasing the fracture toughness by a factor of 7x.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Ablative performance of uncoated silicone-modified and shuttle baseline reinforced carbon composites

The relative ablative performance of uncoated silicone-modified reinforced carbon composite (RCC) and uncoated shuttle baseline RCC substrates was investigated. The test specimens were 13 plies (5.3 to 5.8 millimeters) thick and had a 25-millimeter-diameter test face. Prior to arc tunnel testing, all specimens were subjected to a heat treatment simulating the RCC coating process. During arc tunnel testing, the specimens were exposed to cold wall heating rates of 178 to 529 kilowatts/sq m and stagnation pressures ranging from 0.015 to 0.046 atmosphere at Mach 4.6 in air, with and without preheating in nitrogen. The results show that the ablative performance of uncoated silicone-modified RCC substrates is significantly superior to that of uncoated shuttle baseline RCC substrates over the range of heating conditions used. These results indicate that the silicone-modified RCC substrate would yield a substantially greater safety margin in the event of complete coating loss on the shuttle orbiter.

Dicus, D. L.↗
DOE OSTI2020

Development of Repair Techniques for Cast Iron Engine Blocks by Additive Manufacturing

ORNL partnered with Cummins Inc to demonstrate the feasibility of using additive manufacturing techniques to deposit large volume of new material on cast iron in the context of remanufacturing. Remanufacturing at Cummins Inc is carried out to repair any field damage and, in some cases, provide additional value by adding new features. Large volume deposition on difficult to weld materials is a challenging problem due to involved metallurgy. Phase-1 of this work evaluated the feasibility of using laser directed energy deposition technique to deposit new material layer by layer on cast iron engine blocks. During phase-1 deposits were made using Inconel-718, Nickel, Nr-Cr-B braze filler. Leveraging the knowledge gained during Phase-1, Phase-2 focused on developing a low- cost crack resistant ferrous alloy to repair cast iron via volume deposition techniques without preheating. Three different alloy chemistries were identified, and trials were performed on cast iron substrates to identify the optimal chemistry that provided adequate resistance to cracking in both, the deposits as well as the cast iron substrate.

42 ENGINEERING↗
NASA NTRS1990

A technique for measurement of instantaneous heat transfer in steady-flow ambient-temperature facilities

An experimental technique is described for obtaining time-resolved heat flux measurements with high-frequency response (up to 100 kHz) in a steady-flow ambient-temperature facility. The heat transfer test object is preheated and suddenly injected into an established steady flow. Thin-film gages deposited on the test surface detect the unsteady substrate surface temperature. Analog circuitry designed for use in short-duration facilities and based on one-dimensional semiinfinite heat conduction is used to perform the temperature/heat flux transformation. A detailed description of substrate properties, instrumentation, experimental procedure, and data reduction is given, along with representative results obtained in the stagnation region of a circular cylinder subjected to a wake-dominated unsteady flow. An in-depth discussion of related work is also provided.

O'Brien, James E.↗