Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Structural components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Vertical distribution of structural components in corn stover

In the United States, corn ( Zea mays L.) stover has been targeted for second generation fuel production and other bio-products. Our objective was to characterize sugar and structural composition as a function of vertical distribution of corn stover (leaves and stalk) that was sampled at physiological maturity and about three weeks later from multiple USA locations. A small subset of samples was assessed for thermochemical composition. Concentrations of lignin, glucan, and xylan were about 10% greater at grain harvest than at physiological maturity, but harvestable biomass was about 25% less due to stalk breakage. Gross heating density above the ear averaged 16.3 ± 0.40 MJ kg⁻¹, but with an alkalinity measure of 0.83 g MJ⁻¹, slagging is likely to occur during gasification. Assuming a stover harvest height of 10 cm, the estimated ethanol yield would be >2500 L ha⁻¹, but it would be only 1000 L ha⁻¹ if stover harvest was restricted to the material from above the primary ear. Vertical composition of corn stover is relatively uniform; thus, decision on cutting height may be driven by agronomic, economic and environmental considerations.

09 BIOMASS FUELS↗

The mechanical interaction of clad and base metal for molten salt reactor structural components

Cladding structural components with a corrosion resistant material may greatly extend the design life of molten salt reactor concepts. A complete design methodology for such cladded, high temperature nuclear components will require addressing many issues: fabrication, corrosion resistance, metallurgical interaction, and the mechanical interaction of the clad and base materials under load. This work focuses on the final issue: the mechanical interaction of the base and clad under creep-fatigue conditions. Depending on the relative mechanical properties of the two materials the clad may substantially influence the longterm cyclic response of the structural system or its effect might be negligible. To quantify the effect of different clad material properties we develop an efficient method for simulating pressurized cladded components in the limiting case where the section of interest is far from structural discontinuities. Using this method we evaluate the mechanics of the clad/base system and identify different regimes of mechanical response. The focus is on situations relevant to high temperature nuclear components: thermal-cyclic Bree-type problems and similar axisymmetric structures. The insights gained from these structural studies will form the basis for developing design rules for high-temperature, nuclear, cladded components.

Messner, M. C.↗

Core structured components and containers

A structural component with at least two side members has a support structure that includes a partition with multiple curved portions forming cells. The partition connects to the side members and extends between the side members at least partially along straight lines. The partition may extend along one or more straight lines from one side member to the other. One structural component is a container with a wall about the internal support structure. The container cells may be formed with a core structure. The core can include a permeable storage material and may be retained after formation, or may be removed. In some cases the container wall has generally planar surfaces, which may include surface undulations. Core structures are also provided for forming structural components. Formation can include casting a material about a core structure within a mold to form a partition extending between two or more sides.

Loukus, Adam R.↗

Genes for the Major Structural Components of Thermotogales Species' Togas Revealed by Proteomic and Evolutionary Analyses of OmpA and OmpB Homologs

The unifying structural characteristic of members of the bacterial order Thermotogales is an unusual cell envelope that includes a loose-fitting sheath around each cell, often called a toga. Only two toga-associated structural proteins have been identified in Thermotoga maritima: the anchor protein OmpA1 (previously termed Ompα) and the porin OmpB (previously termed Ompβ). The gene encoding OmpA (ompA1) was assigned in the genome sequence to TM0477, but because no peptide sequence was available for OmpB, its gene (ompB) was not annotated. Here we identify the ompB gene as TM0476, determined by LC/MS/MS analysis of the native OmpB protein purified from T. maritima cells. The purified OmpB had β-sheet secondary structure as determined by circular dichroism. Analysis of the sequence of ompB product shows it has porin characteristics including a carboxy terminus anchoring motif and a porin-specific amino acid composition. Orthologs of ompB were found in the genomes of some, but not all, Thermotogales. Those without orthologs have putative analogs. Phylogenetic analyses of OmpA1 revealed that each species of the Thermotogales has one to three OmpA homologs. T. maritima has two OmpA homologs, encoded by ompA1(TM0477) and ompA2 (TM1729), both of which were found in the toga protein-enriched cell extracts. These annotations of the genes encoding toga structural proteins will guide future examinations of the structure and function of this unusual lineage-defining cell sheath.

59 BASIC BIOLOGICAL SCIENCES↗

U.S. implementation of Q12{sup TM} zirconium alloy for improved stability of structural components

AREVA NP undertook the Q12{sup TM} research and development program to optimize the contribution to fuel assembly dimensional stability of structural components fabricated from ultra-low tin Zr-1Nb-Sn-Fe quaternary alloys. Because Q12{sup TM} is an evolutionary development of the current M5 alloy metallurgy, it benefits from the extensive industrial experience already gained with the latter. The Q12{sup TM} alloy is processed in the same way as M5, with slight increases in tin (Sn) and iron (Fe) contents. For structural components, these chemistry modifications provide higher irradiation creep strength and improved corrosion performance over Zircaloy-4. Fuel assemblies with quaternary alloy guide tubes are thus expected to increase robustness with respect to fuel assembly bow, improve growth characteristics, and maintain high burnup capability. The basic material properties have been determined through various in-core and out-of-core test programs. Components made from Q12{sup TM} have undergone irradiation in lead assemblies and in batch fuel for 13 Pressurized Water Reactor (PWR) units worldwide. Fuel with Q12{sup TM} guide tubes and grids has achieved a fuel assembly average burnup of 60 GWd/tU. Post irradiation examinations of these components have demonstrated that Q12{sup TM} performs in a stable, predictable manner. AREVA NP has submitted a topical report (TR) for Q12{sup TM} as a structural material to the United States Nuclear Regulatory Commission (US-NRC). This TR outlines the material behavior and performance of Q12{sup TM} for both guide tubes and grids. Once approved, implementation of Q12{sup TM} material throughout US PWR fuel designs will enhance dimensional stability of structural components. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Summary of Development for Structural Component Modeling in Fiscal Year 2022

This report summarizes efforts performed during Fiscal Year 2022 to develop capabilities for modeling structural component degradation in support of the U.S. Department of Energy's Nuclear Energy Advanced Modeling and Simulation Program. These efforts were centered around development of capabilities for the Grizzly code. Efforts focused both on foundational engineering-scale analysis capabilities for damage and shell formulations and on material-scale tools for accounting for irradiation effects in Grade 91 steel. A major outcome of this effort was the development of a general-purpose tool for nonlocal averaging of material properties, which enabled nonlocal damage models. In addition, the applicability of the shell elements in MOOSE has been expanded to allow modeling a wider range of component geometries and using a wide variety of material models. For irradiation effects on materials, a previously developed cluster dynamics model for light water reactor pressure vessel steels has been adapted for application to Grade 91 alloy. This work builds on prior efforts to build a flexible, capable code for addressing a variety of aging and component performance issues in nuclear power plant structural components.

36 MATERIALS SCIENCE↗

DIFFERENTIAL EMISSION MEASURE ANALYSIS OF MULTIPLE STRUCTURAL COMPONENTS OF CORONAL MASS EJECTIONS IN THE INNER CORONA

In this paper, we study the temperature and density properties of multiple structural components of coronal mass ejections (CMEs) using differential emission measure (DEM) analysis. The DEM analysis is based on the six-passband EUV observations of solar corona from the Atmospheric Imaging Assembly on board the Solar Dynamic Observatory. The structural components studied include the hot channel in the core region (presumably the magnetic flux rope of the CME), the bright loop-like leading front (LF), and coronal dimming in the wake of the CME. We find that the presumed flux rope has the highest average temperature (>8 MK) and density ({approx}1.0 Multiplication-Sign 10{sup 9} cm{sup -3}), resulting in an enhanced emission measure over a broad temperature range (3 {<=} T(MK) {<=} 20). On the other hand, the CME LF has a relatively cool temperature ({approx}2 MK) and a narrow temperature distribution similar to the pre-eruption coronal temperature (1 {<=} T(MK) {<=} 3). The density in the LF, however, is increased by 2%-32% compared with that of the pre-eruption corona, depending on the event and location. In coronal dimmings, the temperature is more broadly distributed (1 {<=} T(MK) {<=} 4), but the density decreases by {approx}35%-{approx}40%. These observational results show that: (1) CME core regions are significantly heated, presumably through magnetic reconnection; (2) CME LFs are a consequence of compression of ambient plasma caused by the expansion of the CME core region; and (3) the dimmings are largely caused by the plasma rarefaction associated with the eruption.

79 ASTRONOMY AND ASTROPHYSICS↗

Damage prognosis of adhesively-bonded joints in laminated composite structural components of unmanned aerial vehicles

The extensive use of lightweight advanced composite materials in unmanned aerial vehicles (UAVs) drastically increases the sensitivity to both fatigue- and impact-induced damage of their critical structural components (e.g., wings and tail stabilizers) during service life. The spar-to-skin adhesive joints are considered one of the most fatigue sensitive subcomponents of a lightweight UAV composite wing with damage progressively evolving from the wing root. This paper presents a comprehensive probabilistic methodology for predicting the remaining service life of adhesively-bonded joints in laminated composite structural components of UAVs. Non-destructive evaluation techniques and Bayesian inference are used to (i) assess the current state of damage of the system and, (ii) update the probability distribution of the damage extent at various locations. A probabilistic model for future loads and a mechanics-based damage model are then used to stochastically propagate damage through the joint. Combined local (e.g., exceedance of a critical damage size) and global (e.g.. flutter instability) failure criteria are finally used to compute the probability of component failure at future times. The applicability and the partial validation of the proposed methodology are then briefly discussed by analyzing the debonding propagation, along a pre-defined adhesive interface, in a simply supported laminated composite beam with solid rectangular cross section, subjected to a concentrated load applied at mid-span. A specially developed Eliler-Bernoulli beam finite element with interlaminar slip along the damageable interface is used in combination with a cohesive zone model to study the fatigue-induced degradation in the adhesive material. The preliminary numerical results presented are promising for the future validation of the methodology.

42 ENGINEERING↗

Method for real-time inspection of structural components

A multi-mode approach for real-time inspection of structural components may be applied to rapid, wide area measurement of thickness of thick plate-like structures using full-field multi-mode response measurement and analysis. The approach may allow estimation of thickness from full-field multi-mode response to single-tone ultrasonic excitation in thick plates. The approach may utilize wavenumber information across all available wave modes in order to make wavenumber spectroscopy sensitive to changes in thickness for a broader range of nominal initial thicknesses.

Stull, Nicholas D.↗

GP3 is a structural component of the PRRSV type II (US) virion

Glycoprotein 3 (GP3) is a highly glycosylated PRRSV envelope protein which has been reported as being present in the virions of PRRSV type I, while missing in the type II PRRSV (US) virions. We herein present evidence that GP3 is indeed incorporated in the virus particles of a North American strain of PRRSV (FL12), at a density that is consistent with the minor structural role assigned to GP3 in members of the Arterivirus genus. Two 15aa peptides corresponding to two different immunodominant linear epitopes of GP3 derived from the North American strain of PRRSV (FL12) were used as antigen to generate a rabbit monospecific antiserum to this protein. The specificity of this anti-GP3 antiserum was confirmed by radioimmunoprecipitation (RIP) assay using BHK-21 cells transfected with GP3 expressing plasmid, MARC-145 cells infected with FL12 PRRSV, as well as by confocal microscopy on PRRSV-infected MARC-145 cells. To test if GP3 is a structural component of the virion, {sup 35}S-labelled PRRSV virions were pelleted through a 30% sucrose cushion, followed by a second round of purification on a sucrose gradient (20-60%). Virions were detected in specific gradient fractions by radioactive counts and further confirmed by viral infectivity assay in MARC 145 cells. The GP3 was detected in gradient fractions containing purified virions by RIP using anti-GP3 antiserum. Predictably, the GP3 was less abundant in purified virions than other major structural envelope proteins such as GP5 and M. Further evidence of the presence of GP3 at the level of PRRSV FL12 envelope was obtained by immunogold staining of purified virions from the supernatant of infected cells with anti-GP3 antiserum. Taken together, these results indicate that GP3 is a minor structural component of the PRRSV type II (FL12 strain) virion, as had been previously described for PRRSV type I.

60 APPLIED LIFE SCIENCES↗

Nanoparticles as contrast-enhancing agents in optical coherence tomography imaging of the structural components of skin: Quantitative evaluation

This work examines the effect of gold nanoshells and titania nanoparticles on the imaging contrast of structural components of skin in optical coherence tomography (OCT). Experimental data are compared to Monte Carlo (MC) simulation results. In experiments with pig skin in vivo, the epidermis - dermis contrast is improved from 0.78 {+-} 0.03 to 0.92 {+-} 0.04 by gold nanoshells applied to the skin surface and from 0.78 {+-} 0.03 to 0.86 {+-} 0.04 by titania nanoparticles. The contrast of glands is enhanced by titania from 0.68 {+-} 0.12 to 0.84 {+-} 0.07. The highest contrast is reached 120 - 150 min after applying gold nanoshells and 160 - 200 min after applying titania. According to the MC simulation results, the contrast of inclusions increases from zero to 0.85 and 0.65, respectively. (optical tomography)

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Production and validation of scintillating structural components from low-background Poly(ethylene naphthalate)

Poly Ethylene Naphthalate (PEN) is an industrial polymer plastic which is investigated as a low background, transparent, scintillating and wavelength shifting structural material. PEN scintillates in the blue region and has excellent mechanical properties both at room and cryogenic temperatures. Thus, it is an ideal candidate for active structural components in experiments for the search of rare events like neutrinoless double-beta decay or dark matter recoils. Such optically active structures improve the identification and rejection efficiency of backgrounds events, like this improving the sensitivity of experiments. This paper reports on the production of radiopure and transparent PEN plates These structures can be used to mount germanium detectors operating in cryogenic liquids (LAr, LN). Thus, as first application PEN holders will be used to mount the Ge detectors in the LEGEND-200 experiment. The whole process from cleaning the raw material to testing the PEN active components under final operational conditions is reported.

47 OTHER INSTRUMENTATION↗

Frequency shift of Rayleigh line fine structure components in a water solution of 4-methylpyridine as a function of temperature, concentration, and light scattering angle

The frequency shift {Delta}v of the fine structure components of Rayleigh light scattering in 4-methylpyridine water solutions is studied in the ranges of 1 - 0.1 mole fraction concentrations and temperature 10 - 80 {sup 0}C. The laws of {Delta}v variation at different light scattering angles are discussed from the viewpoint of solution structural reorganisation under the varying temperature and concentration of nonelectrolyte in water. Existence of a continuous hydrogen-bond net in the solutions is experimentally proved in a certain range of temperatures and concentrations. (nonlinear optical phenomena)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nuclear Structural Component Relevant Properties of Nickel-Based Alloys Produced via Additive Manufacturing

Idaho National Laboratory initiated examination of nickel-based alloys manufactured via three different additive manufacturing methods for potential applications in nuclear, high temperature structural components. The three methods analyzed included laser powder bed fusion, blown powder laser directed energy deposition, and wire-fed gas metal arc directed energy deposition. With the rapid push towards additive manufacturing, codes do not exist that definitively define what is or is not tolerable for each process and application, such as with conventional, wrought products. This report contains the initial work to understand possible manufacturing methods for high temperature alloys, and specifically, void formation, microstructure evolution, corrosion, and mechanical properties. To generate mechanical test data, specimens were tested irrespective of voids and microstructures were analyzed to better understand how to negate/improve these issues. The preliminary results showed major decreases in mechanical performance for material tested. Test specimens will continue to be produced to further improve each additive manufacturing processes, quantify void acceptance, and better understand the most suitable high temperature alloys receptive to additive manufacturing and high temperature nuclear applications.

36 MATERIALS SCIENCE↗

An Energy Based Fatigue Life Prediction Framework for In-Service Structural Components

An energy based fatigue life prediction framework has been developed for calculation of remaining fatigue life of in service gas turbine materials. The purpose of the life prediction framework is to account aging effect caused by cyclic loadings on fatigue strength of gas turbine engines structural components which are usually designed for very long life. Previous studies indicate the total strain energy dissipated during a monotonic fracture process and a cyclic process is a material property that can be determined by measuring the area underneath the monotonic true stress-strain curve and the sum of the area within each hysteresis loop in the cyclic process, respectively. The energy-based fatigue life prediction framework consists of the following entities: (1) development of a testing procedure to achieve plastic energy dissipation per life cycle and (2) incorporation of an energy-based fatigue life calculation scheme to determine the remaining fatigue life of in-service gas turbine materials. The accuracy of the remaining fatigue life prediction method was verified by comparison between model approximation and experimental results of Aluminum 6061-T6. The comparison shows promising agreement, thus validating the capability of the framework to produce accurate fatigue life prediction.

33 ADVANCED PROPULSION SYSTEMS↗

Report on Understanding and Predicting Effects of Thermal Aging on Microstructure and Tensile Properties of Grade 91 Steel for Structural Components

This report provides an update on understanding and predicting the effects of long-term thermal aging on microstructure and tensile properties of G91 to corroborate the ASME Code rules in strength reduction due to elevated temperature service. The research is to support the design and long-term operation of G91 structural components in sodium-cooled fast reactors (SFRs). The report is a Level 2 deliverable in FY17 (M2AT-17AN1602017), under the Work Package AT-17AN160201, “SFR Materials Testing” performed by the Argonne National Laboratory (ANL), as part of the Advanced Reactor Technologies Program.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

RESOLVING THE STELLAR OUTSKIRTS OF M81: EVIDENCE FOR A FAINT, EXTENDED STRUCTURAL COMPONENT

We present a wide field census of resolved stellar populations in the northern half of M81, conducted with Suprime-Cam on the 8 m Subaru telescope and covering an area {approx}0.3 deg{sup 2}. The resulting color-magnitude diagram reaches over one magnitude below the red giant branch (RGB) tip, allowing a detailed comparison between the young and old stellar spatial distributions. The surface density of stars with ages {approx}<100 Myr is correlated with that of neutral hydrogen in a manner similar to the disk-averaged Kennicutt-Schmidt relation. We trace this correlation down to gas densities of {approx}2 x 10{sup 20} cm{sup -2}, lower than typically probed with H{alpha} flux. Both diffuse light and resolved RGB star counts show compelling evidence for a faint, extended structural component beyond the bright optical disk, with a much flatter surface brightness profile. The star counts allow us to probe this component to significantly fainter levels than is possible with the diffuse light alone. From the colors of its RGB stars, we estimate that this component has a peak global metallicity [M/H] {approx} -1.1 {+-} 0.3 at deprojected radii 32-44 kpc assuming an age of 10 Gyr and distance of 3.6 Mpc. The spatial distribution of its RGB stars follows a power-law surface density profile, I(r) {proportional_to} r {sup -{gamma}}, with {gamma} {approx} 2. If this component were separate from the bulge and from the bright optical disk, then it would contain {approx}10%-15% of M81's total V-band luminosity. We discuss the possibility that this is M81's halo or thick disk, and in particular highlight its similarities and differences with these components in the Milky Way. Other possibilities for its nature, such as a perturbed disk or the faint extension of the bulge, cannot be completely ruled out, though our data disfavor the latter. These observations add to the growing body of evidence for faint, complex extended structures beyond the bright disks of spiral galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗