Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SiO2 anode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Bioinspired mechanically interlocking holey graphene@SiO 2 anode

Mechanically interlocking structures that can enhance adhesion at the interface and regulate the stress distribution have been widely observed in biological systems. Inspired by the biological structures in the wings of beetles, we synthesized a holey graphene@SiO 2 anode with strong mechanical interlocking, characterized it electrochemically, and explained its performance by finite element analysis and density functional calculations. The mechanically interlocking structure enhances lithium-ion (Li + ) storage by transmitting the strain from SiO 2 to the holey graphene and by a mechano-electrochemical coupling effect. The interlocking fit hinders the abscission of SiO 2 and the distinctive structure reduces the stress and strain of SiO 2 during (de)lithiation. The positive mechano-electrochemical coupling effect preserves the amount of electrochemically active phase (Li x Si) during cycles and facilitates Li + diffusion. Therefore, the capacity shows only a slight attenuation after 8000 cycles (cycling stability), and the specific capacity is ~1200 mA h g –1 at 5 A/g (rate-performance). This study furnishes a novel way to design high-performance Li + /Na + /K + /Al 3+ anodes with large volume expansion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Enhanced Interfacial Stability of Si Anodes for Li-Ion Batteries via Surface SiO2 Coating

Silicon is a promising alloying anode for lithium-ion batteries owing to its high capacity and low cost. However, its use has been hampered by mechanical failure arising from the large volume change upon cycling and by an insufficiently stable solid-electrolyte interphase (SEI). SEI formation depends on the Si surface, which is often an oxide (SiO x ). In this study we compare three different Si surfaces using Si wafers: 1.3 nm native SiO x , 1.4 nm thermally grown SiO2, and a SiOx-free surface. The oxide-free surface showed the worst electrochemical performance, never exceeding 94% Coulombic efficiency (CE). Furthermore, it also exhibited the thickest SEI and the highest overpotential for lithiation, which correlated with uninhibited electrolyte reduction and the incorporation of P-F species into the SEI. The oxide-coated surfaces performed significantly better, demonstrating a CE above 99% beyond the second cycle, low overpotential for lithiation, and a thinner and more stable SEI. The oxides lower the onset potential for electrolyte reduction, and yield an SEI with fewer P-F species. However, it was found that the CE with the native oxide surface decays from the fifth cycle onwards and correlates with a resurgence of electrolyte reduction. A 1-2 nm thermal SiO 2 coating is optimum for achieving a stable SEI that minimizes side reactions and sustains efficient cycling.

25 ENERGY STORAGE↗
DOE OSTI2020

Investigating the Chemical Reactivity of Lithium Silicate Model SEI Layers

Silicon anodes suffer from an unstable solid electrolyte interphase (SEI) layer that contributes to undesirable capacity fade with cycling. A key part to addressing this unstable SEI formation is to examine how certain components of the SEI react with the electrolyte over time. One SEI component that has not been thoroughly studied in the context of the chemical reactivity against the electrolyte is lithiated silicate. Four model silicate thin films with increasing lithium content were deposited by radio frequency (RF) magnetron sputtering to study how the lithiation of the native oxide on a silicon anode affects the chemical stability of the anode surface. SiO2, Li2Si2O5, Li2SiO3, and Li3SiOx films were exposed to 1.2 M LiPF6 in the 3:7 wt% ethylene carbonate/ethyl methyl carbonate (EC/EMC) electrolyte for periods of time that are representative of the amount of time it takes to undergo cell formations. Soaked samples were rinsed, dried, and characterized by a combination of attenuated total reflectance-infrared spectroscopy (ATR-IR), focused ion beam-secondary electron microscopy (FIB-SEM), and X-ray photoelectron spectroscopy (XPS) depth profiling. It was found that the rate of the decrease in film thickness of the silicates exposed to the electrolyte over time increases as a function of the lithium content in the thin film. This reaction involves HF etching and LiPF6 salt degradation leading to silicate loss and fluorination throughout the bulk. Understanding this chemical instability is critical to determining the overall mechanism of SEI degradation over time.

ADVANCED PROPULSION SYSTEMS,ENERGY STORAGE↗
NASA NTRS1985

Design, fabrication, and performance of a whiskerless Schottky diode for millimeter and submillimeter wave applications

Design considerations, fabrication techniques, and performance predictions are presented for a planar whiskerless Schottky diode to be used (in radio astronomy applications) at 100-300 GHz. The anode and ohmic contacts are on the same side of the device, and proton bombardment is used to establish the divided surface (by making some regions of the GaAs wafer semiinsulating) prior to definition of a B-doped SiO2 finger, ohmic contacting, anode formation, and anode contact metallization (all using photolithographic techniques). The contributions of parasitic elements are calculated for a device with a 3.5-micron-deep n(+) layer doped at 2 x 10 to the 18th/cu cm, a 250-nm-thick epitaxial layer doped at 5 x 10 to the 16th/cu cm, and a 1-micron-radius anode (providing zero-bias junction capacitance 7 fE). It is predicted that such a device would have total series resistance 12.58 ohm and total shunt capacitance 1.37 fF, compared with 14.27 ohm and 0.93 fF for the corresponding whiskered device.

Mckinney, K.↗
NASA NTRS1990

Space environmental effects on spacecraft thermal control coatings

A large portion of the space based applications in the near future are for low Earth orbit (LEO) including the Space Station Freedom (SSF). The lifetime needs for materials on the SSF is 30 years. Materials must be selected which can withstand the deleterious effects of LEO. Environmental effects in the LEO include atomic oxygen, UV, ionizing radiation, and hypervelocity impact. These effects can adversely affect the surface properties of materials. This is particularly critical in the case of thermal control materials where the efficiency of the thermal control is dependent on the stability of the surface properties. The current baseline thermal coating for the SSF radiators is Ag Teflon. The surface property requirements for the coatings are a solar absorptance of 0.2 and an infrared emittance of 0.8. The effects of atomic oxygen and UV radiation on the baseline coating and several other candidate thermal control materials were studied. The thermal control radiator materials included Ag and Al backed Teflon, H2SO4 anodized Al, sputter deposited SiO2 on Al, and Ag and Al backed polychloro trifluoroethylene. The simulation of several of the LEO environment constituents provided a data base to aid in the selection of the radiator thermal control material to meet the life requirements of the SSF. The effects are illustrated of the environment on thermal control coatings and the importance of this factor in the selection process for long life spacecraft materials.

Bartosik, L. G.↗
DOE OSTI2021

Siloxane Deposition on the Ni-YSZ Solid Oxide Fuel Cell Anode Exposed to Bio-Syngas

Siloxane, a common contaminant present in biogas, is known for adverse effects on cogeneration prime movers. In this study, the siloxane deposition products and mechanism in the solid oxide fuel cell nickel-yttria stabilized zirconia (Ni-YSZ) anode are investigated analytically and experimentally. An SOFC with Ni-YSZ anode and pure Ni/YSZ pellets were exposed to a simulated biogas-reformate fuel with octamethylcyclotetrasiloxane (D4) contamination at 750 °C. The electrochemical characterization results show that the SOFCs performance degradation caused by D4 contamination is irreversible. Morphology and XRD results illustrate that silicon and carbon deposition can both be detected in the anode and pellets. Graphite, SiC and SiO2 are all possible products based on the results of XRD test. Here, according to the formation of graphite and SiC, the new mechanism suggests that carbon is also an essential factor in siloxane contamination of Ni-YSZ anodes besides silicon, which can be explained by the catalytic and electrochemical analysis.

25 ENERGY STORAGE↗
NASA NTRS1991

Magma Electrolysis: An update

Electrolytic extraction of O2 from molten lunar soil is conceptually simple and thus a candidate process for producing O2 on the Moon. Possible container and electrode materials are being tested for durability in corrosive high-temperature silicate melts and looking for complications that might increase energy requirements. Gaseous oxygen is being produced by electrolysis of 1-2 gram quantities of silicate melts in spinel (MgAl2O4) crucibles; in these melts, spinel is a stable phase. The concentration of FeO was kept low because FeO decrease O2 production efficiency. Platinum electrodes were placed about 0.5 cm apart in the melt. The spinel crucible was still intact after 40 minutes of electrolysis, when the experiment was halted for examination. The Pt anode was also intact; its Pt was maintained in a dynamci state in which the anode was continuously oxidized but quickly reduced again by the silicate melt, inhibiting migration of Pt away from the anode. In melts with low concentrations of Al2O3 + SiO2 (2 wt percent), the energy of resistance heating was only approximately equal to 10 to 20 percent of the theoretical amount required to produce O2. In melts substantially more concentrated in Al2O3 + SiO2, higher melt viscosity resulted in frothing that, in the worst case, caused high enough melt resistivities to raise the energy requirements to nearly 10 times theoretical. Both Fe and Si are produced at the cathode; in iron-rich melts, a- and c-iron and molten ferrosilicon were observed. Production was also observed at the cathode of a previously unrecognized gas; which is not yet identified. The solubility of metallic species was measured in silicate melts. They are too low to reduce significantly the efficiency of O2 production.

Colson, Russell O.↗
DOE OSTI2021

Facile Synthesis of Micrometer-sized Hierarchical Porous Si@C Anodes for High-Performance Lithium-Ion Batteries

Extensive studies have been conducted to determine if replacing graphite anodes with silicon is feasible since silicon possesses a high capacity and is an abundant resource; however, Si anodes suffer significant volume changes during cycling, which pulverizes its structure and subsequently causes rapid capacity fading. We used SiO2 nanoparticles (nSiO2) and low-cost coal-derived humic acid as a feedstock to synthesize high performance Si-C anodes for Li-ion Batteries through spray drying, calcination, and magnesiothermic reductions. Our Si-C anodes features micrometer-sized porous Si coated with a graphitized carbon shell (mpSi@C). The hierarchical graphitized carbon shell and porous silicon structure relieve the mechanical stress of the Si phase upon cycling, which stabilizes the structure. This mpSi@C composite design allows for a high initial discharge capacity of 2199.9 mAh g-1 at 0.1 A g-1 and a cycling performance of 68% capacity retention after 100 cycles at 1.0 A g-1. The multipoint contact between the Si anode and C structure allows for a remarkable performance rate of 566.3 mAh g-1 at 5.0 A g-1.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1981

Low temperature growth and electrical characterization of insulators for GaAs MISFETS

Progress in the low temperature growth of oxides and layers on GaAs and the detailed electrical characterization of these oxides is reported. A plasma anodization system was designed, assembled, and put into operation. A measurement system was assembled for determining capacitance and conductance as a function of gate voltage for frequencies in the range from 1 Hz to 1 MHz. Initial measurements were carried out in Si-SiO2 capacitors in order to test the system and in GaAs MIS capacitors abricated using liquid anodization.

Borrego, J. M.↗
NASA NTRS2008

Solid-State High-Temperature Power Cells

All-solid-state electrochemical power cells have been fabricated and tested in a continuing effort to develop batteries for instruments for use in environments as hot as 500 C. Batteries of this type are needed for exploration of Venus, and could be used on Earth for such applications as measuring physical and chemical conditions in geothermal and oil wells, processing furnaces, and combustion engines. In the state-of-the-art predecessors of the present solid-state power cells, fully packaged molten eutectic salts are used as electrolytes. The molten-salt-based cells can be susceptible to significant amounts of self-discharge and corrosion when used for extended times at elevated temperatures. In contrast, all-solid-state cells such as the present ones are expected to be capable of operating for many days at temperatures up to 500 C, without significant self-discharge. The solid-state cell described here includes a cathode made of FeS2, an electrolyte consisting of a crystalline solid solution of equimolar amounts of Li3PO4 and Li4SiO4, and an anode made of an alloy of Li and Si (see figure). The starting material for making the solid electrolyte is a stoichiometric mixture of Li3PO4, SiO2, and Li3CO2. This mixture is ball-milled, then calcined for two hours at a temperature of 1,100 C, then placed in a die atop the cathode material. Next, the layers in the die are squeezed together at a pressure between 60 and 120 MPa for one hour at a temperature of 600 C to form a unitary structure comprising the solid electrolyte and cathode bonded together. Finally, the lithium-alloy anode is pressure-bonded to the solid electrolyte layer, using an intermediate layer of pure lithium. In one test of a cell of this type, a discharge rate of about 1 mA per gram of cathode material was sustained for 72 hours at a temperature of about 460 C. This is about three times the discharge rate required to support some of the longer duration Venus-exploration mission scenarios.

Whitacre, Jay↗
NASA NTRS1978

Coatings in space environment

The behavior in space environment of evaporated Al uncoated and coated with reactively deposited silicon oxide (SiOx), electron beam evaporated SiO2 and Al2O3, and Al and Ag coated with double layers of Al2O3 + SiOx is compared with metallized Teflon and Kapton, anodized Al (Alzak), and white paints. Flight data from three calorimetric experiments and one reflectometer flown in different orbital environments are compared with laboratory test data. The results demonstrate that evaporated thin films are extremely versatile and stable coatings for space applications. Through the use of control samples studied in different laboratory tests and monitored for up to 12,000 hours of solar exposure in different orbits, a classification of orbital severity and an estimate of laboratory simulation accuracy is obtained.

Triolo, J. J.↗
NASA NTRS1982

Ellipsometric studies of sputtered silicon nitride on n-GaAs

Ellipsometry, which is the study of optical systems through their effect on polarized light, is a nondestructive technique offering extremely high sensitivity and in situ operation. One of the intriguing possibilities is to make use of the high sensitivity of ellipsometry for studying the very thin interface between an insulating film and a semiconductor substrate. Researchers have been especially interested in native or anodic oxides. In a recent study, Aspnes and Theeten used ellipsometry to study the interface between silicon and its thermally grown oxide, SiO2. These authors were able to conclude that the interface consisted of a 7 +/- 2 A graded region of atomically mixed silicon and oxygen. In this paper we report both analysis and experimental results for the system: sputtered silicon nitride on (100) n-type gallium arsenide.

Peng, Y. K.↗
DOE OSTI2024

Characterization of electromigration-induced short-range stress development in Al(0.25 at. % Cu) conductor line

Scanning x-ray microbeam topography and fluorescence experiments were conducted in situ to study the electromigration behavior of a 0.5 μm thick, 10 μm wide, and 200 μm long Al(0.25 at. % Cu) conductor line with 1.5 μm-thick SiO2 passivation on a single crystal Si substrate. The strain sensitivity of x-ray topography measurement allowed detailed examination of the electromigration-induced stress distribution and evolution in the conductor line in response to the depletion of Cu solute early in the electromigration process. Upon electromigration at 0.4 MA/cm2 and 303 °C, a short-range stress gradient was quickly induced by Al migration in the Cu-depleted cathode region to counteract further Al flow. The stress gradient was fully developed during the 5.3 h incubation time, extending over the critical Blech length of about 66 μm from the cathode end. Plastic deformation then occurred at the downstream end of the Cu-depleted region. The preferential electromigration of Cu did not cause detectable stress change outside the Cu-depleted region, except for the significant stress development from the Al2Cu precipitation at the anode end which appeared to initiate the fracture in the passivation. Preliminary finite difference modeling was undertaken to simulate the experimental observations, from which important parameters dictating electromigration in Al(Cu) line were extracted: an apparent effective valence of −5.6 and −1.9 for Cu and Al in Al(Cu), respectively, and a critical Cu concentration of 0.16 at. % above which Al grain boundary diffusion is effectively blocked.

Physics↗
DOE OSTI2025

Nanoscopic Plugs Block Hydrogen Crossover in Submicron Thick Proton-Conducting SiO 2 Membranes for Water Electrolysis

Zero-gap electrolyzers based on submicron thick proton-conducting oxide membranes (POMs) represent a promising approach to increasing the efficiency of H 2 production from water electrolysis while moving away from conventional perfluorosulfonic acid (PFSA) membranes. A critical barrier to the commercialization of such electrolyzers is that the ultrathin nature of POMs, which is necessary to achieve low cell resistance, makes them more susceptible to defects that can lead to unacceptably high rates of H 2 crossover. Herein, we demonstrate an approach to mitigate this problem through selective deposition of carbon-containing silicon oxide (SiO x C y ) “nanoplugs” into the defects of submicron thick SiO 2 membranes using a facile electrochemically mediated deposition process. Selective deposition of nanoplugs within the defects was verified by multiple characterization techniques, while scanning electrochemical microscopy (SECM) was used to confirm selective plugging of H 2 -crossover hotspots associated with defects at identical locations. Thanks to the use of nanoplugs, the H 2 permeance of 250 nm thick SiO 2 membranes was reduced by 5 to 6 orders of magnitude compared to the unmodified atomic layer deposition (ALD) SiO 2 membranes while having negligible impact on the ionic resistance of the membrane. These plug-modified membranes also enabled safe and stable operation of a zero-gap full cell electrolysis cell, in contrast to cells lacking nanoplugs that produced anode effluent streams having H 2 concentrations near or exceeding the lower flammability limit (LFL) of H 2 . Furthermore, beyond water electrolysis, this defect-sealing strategy has the potential to be broadly implemented in other applications, such as fuel cells and flow batteries, offering a versatile solution to mitigate crossover-related performance losses.

ALD SiO2↗