Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Schottky barrier diode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Silicon Carbide Schottky Barrier Diode

This chapter reviews the status of SiC Schottky barrier diode development. The fundamental of Schottky barrier diodes is first provided, followed by the review of high-voltage SiC Schottky barrier diodes, junction-barrier Schottky diodes, and merged-pin-Schottky diodes. The development history is reviewed ad the key performance parameters are discussed. Applications of SiC SBDs in power electronic circuits as well as other areas such as gas sensors, microwave and UV detections are also presented, followed by discussion of remaining challenges.

Zhao, Jian H.↗
DOE OSTI2024

High-current, high-voltage AlN Schottky barrier diodes

AlN Schottky barrier diodes with low ideality factor (<1.2), low differential ON-resistance (<0.6 mΩ cm 2 ), high current density (>5 kA cm −2 ), and high breakdown voltage (680 V) are reported. The device structure consisted of a two-layer, quasi-vertical design with a lightly doped AlN drift layer and a highly doped Al 0.75 Ga 0.25 N ohmic contact layer grown on AlN substrates. A combination of simulation, current–voltage measurements, and impedance spectroscopy analysis revealed that the AlN/AlGaN interface introduces a parasitic electron barrier due to the conduction band offset between the two materials. This barrier was found to limit the forward current in fabricated diodes. Further, we show that introducing a compositionally-graded layer between the AlN and the AlGaN reduces the interfacial barrier and increases the forward current density of fabricated diodes by a factor of 10 4 .

Quiñones, C. E. (ORCID:0000000192703747)↗
NASA NTRS2008

Schottky barrier diode and method thereof

Pt/n.sup.-GaN Schottky barrier diodes are disclosed that are particularly suited to serve as ultra-violet sensors operating at wavelengths below 200 nm. The Pt/n.sup.-GaN Schottky barrier diodes have very large active areas, up to 1 cm.sup.2, which exhibit extremely low leakage current at low reverse biases. Very large area Pt/n.sup.-GaN Schottky diodes of sizes 0.25 cm.sup.2 and 1 cm.sup.2 have been fabricated from n.sup.-/n.sup.+ GaN epitaxial layers grown by vapor phase epitaxy on single crystal c-plane sapphire, which showed leakage currents of 14 pA and 2.7 nA, respectively for the 0.25 cm.sup.2 and 1 cm.sup.2 diodes both configured at a 0.5V reverse bias.

Aslam, Shahid↗
NASA NTRS1992

New approach to the design of Schottky barrier diodes for THz mixers

Near-ideal GaAs Schottky barrier diodes especially designed for mixing applications in the THz frequency range are presented. A diode fabrication process for submicron diodes with near-ideal electrical and noise characteristics is described. This process is based on the electrolytic pulse etching of GaAs in combination with an in-situ platinum plating for the formation of the Schottky contacts. Schottky barrier diodes with a diameter of 1 micron fabricated by the process have already shown excellent results in a 650 GHz waveguide mixer at room temperature. A conversion loss of 7.5 dB and a mixer noise temperature of less than 2000 K have been obtained at an intermediate frequency of 4 GHz. The optimization of the diode structure and the technology was possible due to the development of a generalized Schottky barrier diode model which is valid also at high current densities. The common diode design and optimization is discussed on the basis of the classical theory. However, the conventional fomulas are valid only in a limited forward bias range corresponding to currents much smaller than the operating currents under submillimeter mixing conditions. The generalized new model takes into account not only the phenomena occurring at the junction such as current dependent recombination and drift/diffusion velocities, but also mobility and electron temperature variations in the undepleted epi-layer. Calculated diode I/V and noise characteristics are in excellent agreement with the measured values. Thus, the model offers the possibility of optimizing the diode structure and predicting the diode performance under mixing conditions at THz frequencies.

Jelenski, A.↗
NASA NTRS1986

Conversion losses in GaAs Schottky-barrier diodes

The conversion losses of a Schottky-barrier diode have been calculated for a set of realistic diode parameters. It is found that previous work overestimated the substrate losses by 30 percent. It is also shown that a lightly doped epitaxial layer will decrease the barrier capacitance and with properly designed thickness will avoid any resistance losses due to this layer. Parasitic losses can thus be reduced substantially.

Von Roos, O.↗
DOE OSTI2023

Low-frequency noise in β-(Al x Ga1 −x )2O3 Schottky barrier diodes

We report on the low-frequency electronic noise in β-(AlxGa1−x)2O3 Schottky barrier diodes. The noise spectral density reveals 1/f dependence, characteristic of the flicker noise, with superimposed Lorentzian bulges at the intermediate current levels (f is the frequency). The normalized noise spectral density in such diodes was determined to be on the order of 10−12 cm2/Hz (f = 10 Hz) at 1 A/cm2 current density. At the intermediate current regime, we observed the random telegraph signal noise, correlated with the appearance of Lorentzian bulges in the noise spectrum. The random telegraph signal noise was attributed to the defects near the Schottky barrier. The defects can affect the local electric field and the potential barrier and, correspondingly, impact the electric current. The obtained results help in understanding the noise in Schottky barrier diodes made of ultra-wide bandgap semiconductors and can be used for the material and device quality assessment.

Physics↗
NASA NTRS1988

Barrier height enhancement of InP-based n-Ga(0.47)In(0.53)As Schottky-barrier diodes grown by molecular beam epitaxy

Barrier height enhancement of an InP-based p(+)n-Ga(0.47)In(0.53)As Schottky diode grown by MBE has been demonstrated for infra-red photodetector applications. A barrier height of 0.35 eV for n-Ga(0.47)In(0.53)As Schottky barrier diodes, was increased to the effective barrier height of 0.55 eV, with a p(+)-Ga(0.47)In(0.53)As surface layer of 30 nm thick. The results show a reverse leakage current density of 0.0015 A/sq cm and a junction capacitance of 0.3 pF, which are comparable to those of p-Ga(0.47)In(0.53)As Schottky-barrier diodes at a reverse bias voltage of 5 V.

Kim, J. H.↗
NASA NTRS1990

Self-Aligned Guard Rings For Schottky-Barrier Diodes

Proposed self-aligned guard ring increases active area of Schottky-barrier infrared detector. Concept developed for silicide Schottky-barrier diodes in which platinum silicide or iridium silicide Schottky-contacts provide cutoff wavelengths of about 6 or 10 micrometers. Grid of silicon dioxide doped with phosphorus etched on silicon wafer, and phosphorus from grid diffused into substrate, creating n-type guard rings. Silicide layers formed in open areas of grid. Overlap of guard rings and silicide layers small.

Lin, True-Lon↗
DOE OSTI2024

Over 600 V Lateral AlN-on-AlN Schottky Barrier Diodes with Ultra-Low Ideality Factor

Abstract This letter reports the demonstration of lateral AlN Schottky barrier diodes (SBDs) on single-crystal AlN substrates by metalorganic CVD (MOCVD) with an ultra-low ideality factor ( η ) of 1.65, a high Schottky barrier height of 1.94 eV, a breakdown voltage ( BV ) of 640 V, and a record high normalized BV by the anode-to-cathode distance. The device current was dominated by thermionic emission, while most previously reported AlN SBDs suffered from defect-induced current with higher η (>4). This work represents a significant step towards high-performance ultra-wide bandgap AlN-based high-voltage and high-power devices.

Physics↗
DOE OSTI2023

Ultrawide bandgap vertical β-(Al x Ga1 −x )2O3 Schottky barrier diodes on free-standing β-Ga2O3 substrates

Ultrawide bandgap β-(AlxGa1−x)2O3 vertical Schottky barrier diodes on (010) β-Ga2O3 substrates are demonstrated. The β-(AlxGa1−x)2O3 epilayer has an Al composition of 21% and a nominal Si doping of 2 × 1017 cm−3 grown by molecular beam epitaxy. Pt/Ti/Au has been employed as the top Schottky contact, whereas Ti/Au has been utilized as the bottom Ohmic contact. The fabricated devices show excellent rectification with a high on/off ratio of ∼109, a turn-on voltage of 1.5 V, and an on-resistance of 3.4 mΩ cm2. Temperature-dependent forward current-voltage characteristics show effective Schottky barrier height varied from 0.91 to 1.18 eV while the ideality factor from 1.8 to 1.1 with increasing temperatures, which is ascribed to the inhomogeneity of the metal/semiconductor interface. The Schottky barrier height was considered a Gaussian distribution of potential, where the extracted mean barrier height and a standard deviation at zero bias were 1.81 and 0.18 eV, respectively. A comprehensive analysis of the device leakage was performed to identify possible leakage mechanisms by studying temperature-dependent reverse current-voltage characteristics. At reverse bias, due to the large Schottky barrier height, the contributions from thermionic emission and thermionic field emission are negligible. By fitting reverse leakage currents at different temperatures, it was identified that Poole–Frenkel emission and trap-assisted tunneling are the main leakage mechanisms at high- and low-temperature regimes, respectively. Electrons can tunnel through the Schottky barrier assisted by traps at low temperatures, while they can escape these traps at high temperatures and be transported under high electric fields. This work can serve as an important reference for the future development of ultrawide bandgap β-(AlxGa1−x)2O3 power electronics, RF electronics, and ultraviolet photonics.

Materials Science↗
DOE OSTI2024

High-voltage AlN Schottky barrier diodes on bulk AlN substrates by MOCVD

Abstract This letter reports the demonstration of Aluminum nitride (AIN) Schottky barrier diodes on bulk AlN substrates by metalorganic chemical vapor phase deposition with breakdown voltages exceeding 3 kV. The devices exhibited good rectifying characteristics with ON/OFF ratios of 10 6 –10 8 and excellent thermal stability from 298 to 623 K. The device Schottky barrier height increased from 0.89 to 1.85 eV, and the ideality factor decreased from 4.29 to 1.95 with increasing temperature, ascribed to the inhomogeneous metal/AlN interface. This work demonstrates the potential of AlN as an ultra-wide bandgap semiconductor for developing multi-kV AlN high-voltage and high-power devices.

Physics↗
NASA NTRS1987

Optical response at 10.6 microns in tungsten silicide Schottky barrier diodes

Optical response to radiation at a wavelength of 10.6 microns in tungsten silicide-silicon Schottky barrier diodes has been observed. Incident photons excite electrons by means of junction plasmon assisted inelastic electron tunneling. At 78 K, a peak in the second derivative of current versus junction bias voltage was observed at a voltage corresponding to the energy of photons having a wavelength of 10.6 microns. This peak increased with increasing incident laser power, saturating at the highest laser powers investigated.

Kumar, Sandeep↗
NASA NTRS1988

Conversion Losses In GaAs Schottky-Barrier Diodes

Parasitic losses reduced with lightly doped epitaxial layers of proper thickness. Report presents calculations of conversion losses in Schottky-barrier diodes. Theoretical work directed toward reduction of parasitic losses through proper design of space-charge layers; possible, to reduce barrier capacitances and contributions to barrier resistances from undepleted epitaxial layers.

Von Roos, Oldwig↗
DOE OSTI2022

AlN quasi-vertical Schottky barrier diode on AlN bulk substrate using Al 0.9 Ga 0.1 N current spreading layer

Abstract An aluminum nitride (AlN) quasi-vertical Schottky barrier diode (SBD) was fabricated on an AlN bulk substrate. An undoped AlN layer, a Si-doped Al 0.9 Ga 0.1 N current spreading layer and an AlN buffer layer were grown by plasma-enhanced molecular beam epitaxy. The epitaxial AlN layer was etched down to the n-Al 0.9 Ga 0.1 N layer to form an Ohmic contact. Ni/Au and V/Al/Ni/Au were deposited on the top AlN layer as Schottky contacts and on the exposed n-Al 0.9 Ga 0.1 N layer as Ohmic contacts, respectively. The Ohmic characteristics on the n-Al 0.9 Ga 0.1 N layer, capacitance–voltage ( C – V ) and current–voltage ( I – V ) characteristics of the AlN SBD were investigated.

Physics↗
NASA NTRS1992

InGaAs/InP heteroepitaxial Schottky barrier diodes for terahertz applications

This paper explores the feasibility of planar, sub-harmonically pumped, anti-parallel InGaAs/InP heteroepitaxial Schottky diodes for terahertz applications. We present calculations of the (I-V) characteristics of such diodes using a numerical model that considers tunneling. We also present noise and conversion loss predictions of diode mixers operated at 500 GHz, and obtained from a multi-port mixer analysis, using the I-V characteristics predicted by our model. Our calculations indicate that InGaAs/InP heteroepitaxial Schottky barrier diodes are expected to have an I-V characteristic with an ideality factor comparable to that of GaAs Schottky diodes. However, the reverse saturation current of InGaAs/InP diodes is expected to be much greater than that of GaAs diodes. These predictions are confirmed by experiment. The mixer analyses predict that sub-harmonically pumped anti-parallel InGaAs/InP diode mixers are expected to offer a 2 dB greater conversion loss and a somewhat higher single sideband noise temperature than their GaAs counterparts. More importantly, the InGaAs/InP devices are predicted to require only one-tenth of the local oscillator power required by similar GaAs diodes.

Bhapkar, Udayan V.↗
DOE OSTI2022

β -Ga 2 O 3 Schottky barrier diodes with 4.1 MV/cm field strength by deep plasma etching field-termination Available

In this work, we demonstrate a deep mesa etch design for efficient edge field termination in β-Ga 2 O 3 Schottky barrier diodes (SBDs). The proposed design enabled parallel plate fields higher than 4.1 MV/cm with negligible change to the device ON characteristics. The effect of BCl 3 /Cl 2 -based dry etch on (100) and (010) etched vertical sidewalls is also analyzed. A remarkable anisotropy in depletion was observed for etch along (100) and (010) sidewalls. In conclusion, this work provides insight into the impact of etching on n-type Ga 2 O 3 and shows a promising method to realize efficient field termination for high breakdown field strength SBDs.

42 ENGINEERING↗