Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SUPERSONIC DIFFUSER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1954

Some Observations of Shock-induced Turbulent Separation on Supersonic Diffusers

A survey of experimental data at supersonic speed indicated that shock-induced separation of a turbulent boundary layer will result for Mach numbers of approximately 1.33 or greater when a theoretical stream static-pressure-rise ratio of approximately 1.89 occurs across a shock interacting with the boundary layer. The significance of this tentative criterion for turbulent boundary-layer separation is discussed with respect to the design of supersonic diffusers.

BOUNDARY-LAYER CONTROL--INTERNAL AERODYNAMICS↗
NASA NTRS1951

Preliminary Investigation of a Translating Cowl Technique for Improving Take-off Performance of a Sharp-lip Supersonic Diffuser

A preliminary investigation was conducted in quiescent air on a translating cowl technique for improving the take-off performance of a sharp-lip supersonic diffuser. The technique consists of cutting the cowling in a plane normal to its axis and then translating the forepart of the cowling in the forward direction. The leading edge of the fixed portion of the cowling is rounded. Appreciable improved inlet performance was obtained with a cowling translation corresponding to a gap of only 1/4 inlet radius.

ENGINES, TURBOJET - PERFORMANCE↗
NASA NTRS1984

Flow and heat transfer measurements along a cooled supersonic diffuser

An experimental investigtion was conducted to ascertain the mean flowfield, including shock wave structure, separated flow regions, turbulent boundary-layer growth, static pressure variations, wall heat transfer, and shear stresses in a second-throat, axisymmetric, supersonic diffuser with wall cooling. The diffuser inlet Mach number of the heated air flow was 3.76, the stagnation pressure was 6.8 atm, the ratio of wall to total gas temperature was 0.44, and the diffuser discharged to the atmosphere. The complex flowfield involved deceleration and acceleration regions, supersonic and embedded subsonic regions, and strong viscous regions with relatively large radial and axial variations. The heat transfer and wall static pressure distributions were remarkably similar, and heat transfer rates were high locally at oblique shock/turbulent boundary-layer interactions, in the pseudoshock region, and in the separation region in the diffuser outlet section.

Back, L. H.↗
NASA NTRS1952

Amplitude of Supersonic Diffuser Flow Pulsations

A theoretical method for evaluating the stability characteristics and the amplitude and the frequency of pulsation of ram-jet engines without heat addition is presented herein. Experimental verification of the theoretical results are included where data were available. Theory and experiment show that the pulsation amplitude of a high mass-flow-ratio diffuser having no cone surface flow separation increases with decreasing mass flow. The theoretical trends for changes in amplitude, frequency, and mean-pressure recovery with changes in plenum-chamber volume were experimentally confirmed. For perforated convergent-divergent-type diffusers, a stability hysteresis loop was predicted on the pressure-recovery mass-flow-ratio curve. At a given mean mass-flow ratio, the higher.value of mean pressure recovery corresponded to oscillatory flow in the diffuser while the lower branch was stable. This hysteresis has been observed experimentally. The theory indicates that for a ram-jet engine of given diameter, the amplitude of pulsation of a supersonic diffuser is increased by decreasing the relative size of the plenum chamber with respect to the diffuser volume down to a critical value at which oscillations cease. In the region of these critical values, the stable mass-flow range of the diffuser may be increased either by decreasing the combustion chamber volume or by increasing the length of the diffuser.

Sterbentz, William H.↗
NASA NTRS1951

Preliminary Investigation of Use of Conical Flow Separation for Efficient Supersonic Diffusion

Use of flow separation on a rod projecting upstream of a blunt body to decelerate the supersonic stream ahead of an annular nose inlet was investigated at Mach numbers of 1.76, 1.93, and 2.10. Maximum pressure recoveries were obtained with rod tip projections about 1.5 times the radius of the spherical nose and were higher than those obtained with single-shock solid cones. Subcritical operation was similar to that observed with solid-cone inlets, but the effect of angle of attack on maximum pressure recovery was more severe.

WIND TUNNEL TESTS - LFPL - SUPERSONIC (18"x18")↗
NASA NTRS1952

Evaluation of five conical center-body supersonic diffusers at several angles of attack

Five supersonic inlets having conical center bodies were investigated in a 16-inch ram jet engine with and without combustion at Mach numbers of 1.7, 1.9, and 2.0 and angles of attack from 0 degrees to 10 degrees. Four of the inlets were of the low-mass-flow-ratio type whereas the fifth inlet was of the high-mass-flow-ratio type. The stable operating range of the four low-nass-flow-ratio inlets decreased considerably as the angle of attack was increased despite an increase of the cone angle or the use of boundary-layer bleed. The stable range of the high-mass-flow-ratio inlet increased considerably both at 0 degrees and at greater angles of attack as the free-stream Mach number was decreased. Free-stream Mach number, angle of attack, and inlet type had negligible effects on combustion efficiency, temperature ratio, or combustion-chamber inlet Mach number in the supercritical region.

Englert, Gerald W↗
NASA NTRS1952

Pressure Recovery, Drag, and Subcritical Stability Characteristics of Three Conical Supersonic Diffusers at Stream Mach Numbers from 1.7 to 2.0

A study of a 20 degree and a 25 degree half-angle high mass-flow ratio conical supersonic inlet was made on a 16-inch ram jet in the 8- by 6-foot supersonic tunnel. A greater range of stable subcritical operation was obtained with the low mass-flow ratio inlets; a greater range was obtained with the 25 degree than with the 20 degree half-angle low mass-flow ratio inlet. The high mass-flow ratio inlet had the least drag.

DIFFUSERS, SUPERSONIC↗
NASA NTRS1952

Pressure recovery, drag, and subcritical stability characteristics of conical supersonic diffusers with boundary-layer removal

A study of two 20 degrees half-angle, low mass-flow ratio conical supersonic inlets with cone boundary-layer bleed was made on a 16-inch ram-jet engine in the Lewis 8- by 6-foot supersonic wind tunnel. A greater stable subcritical range of operation was obtained with the bleed inlets than with the corresponding inlet without boundary-layer bleed. The drag added by the bleed system was small.

Obey, Leonard T↗
NASA NTRS1950

Effect of Ram-jet Pressure Pulsations on Supersonic-diffuser Performance

Experimental study of effects of combustion roughness and controlled mechanical oscillations on diffuser operation was conducted on an 8-inch ram jet at Mach number 1.87. Within experimental accuracy, the optimum mean combustion-chamber static pressure occurred when the maximum instantaneous static pressure equalled the optimum steady-flow value and the corresponding decrement in optimum mean static pressure was equal to one-half the total amplitude of the pressure pulsations. A marked attenuation of amplitude of cold-buzz pressure fluctuations was effected over limited range of subcritical diffuser operation by means of properly tuned rotating disk located in combustion chamber.

Connors, James F↗