Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILVER 93”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

NASA welding assessment program

A program was conducted to demonstrate the cycle life capability of welded solar cell modules relative to a soldered solar cell module in a simulated low earth orbit thermal environment. A total of five 18-cell welded (parallel gap resistance welding) modules, three 18-cell soldered modules, and eighteen single cell samples were fabricated using 2 x 4 cm silicon solar cells from ASEC, fused silica cover glass from OCLI, silver plated Invar interconnectors, DC 93-500 adhesive, and Kapton-Kevlar-Kapton flexible substrate material. Zero degree pull strength ranged from 2.4 to 5.7 lbs for front welded contacts (40 samples), and 3.5 to 6.2 lbs for back welded contacts (40 samples). Solar cell cross sections show solid state welding on both front and rear contacts. The 18-cell welded modules have a specific power of 124 W/kg and an area power density of 142 W/sq m (both at 28 C). Three welded and one soldered module were thermal cycle tested in a thermal vacuum chamber simulating a low earth orbit thermal environment.

Patterson, R. E.↗

Observation of enhanced properties in samples of silver oxide doped YBa2Cu3O(x)

Samples of YBa2Cu3O(x) doped with silver oxide (Tc is about 93 K) have exhibited attractive forces in gradient magnetic fields, both normal and tangential to the surfaces, which are more than twice the sample weight. This allows sample suspension below a rare earth magnet. Critical current density was increased by about 100 at 77 K. Persistent fields, flux pinning, magnetization, and modeling are described.

Peters, P. N.↗

Performance of a high T(sub c) superconducting ultra-low loss microwave stripline filter

Discussed here is the successful fabrication of a five-pole interdigital stripline filter made of the 93-K superconductor (Y1Ba2Cu3O(y)) coated on a silver substrate, with center frequency of 8.5 GHz and an extremely high rejection ratio of 80 dB. The lowest insertion loss measured was 0.1 dB at 12 K, with a return loss of better than 16 dB, representing a significant improvement over a similar copper filter; it is comparable to low critical temperature filters. The insertion loss appears to be limited by extrinsic factors, such as tuning mismatch and joint losses, and not by the superconducting material losses.

Bautista, J. J.↗

Performance of a high Tc superconducting ultralow-loss microwave stripline filter

The successful fabrication is reported of a five-pole interdigital stripline filter made of the 93 K superconductor Y1Ba2Cu3O(y) coated on a silver substrate, with a center frequency of 8.5 GHz and an extremely high rejection ratio of 80 dB. The lowest insertion loss measured was 0.1 dB at 12 K, with a return loss better than 16 dB, representing significant improvements over a similar Cu filter, and comparable to low Tc filters. The insertion loss appears to be limited by extrinsic factors such as tuning mismatch and joint losses, and not by the superconducting material losses.

Zahopoulos, C.↗

Performance of a high T (sub c) superconducting ultra-low loss microwave stripline filter

Discussed here is the successful fabrication of a five-pole interdigital stripline filter made of the 93 K superconductor (Y1Ba2Cu3O sub y) coated on a silver substrate, with center frequency of 8.5 GHz and an extremely high rejection ratio of 80 dB. The lowest injection loss measured was 0.1 dB at 12 K, with a return loss of better than 16 dB, representing a significant improvement over a similar copper filter, and is comparable to low critical temperature filters. The insertion loss appears to be limited by extrinsic factors, such as tuning mismatch and joint losses, and not by superconducting material losses.

Bautista, J. J.↗

Thermal Performance of Orion Active Thermal Control System With Seven-Panel Reduced-Curvature Radiator

The active thermal control system (ATCS) of the crew exploration vehicle (Orion) uses radiator panels with fluid loops as the primary system to reject heat from spacecraft. The Lockheed Martin (LM) baseline Orion ATCS uses eight-panel radiator coated with silver Teflon coating (STC) for International Space Station (ISS) missions, and uses seven-panel radiator coated with AZ 93 white paint for lunar missions. As an option to increase the radiator area with minimal impact on other component locations and interfaces, the reduced-curvature (RC) radiator concept was introduced and investigated here for the thermal perspective. Each RC radiator panel has 15 percent more area than each Lockheed Martin (LM) baseline radiator panel. The objective was to determine if the RC seven-panel radiator concept could be used in the ATCS for both ISS and lunar missions. Three radiator configurations the LM baseline, an RC seven-panel radiator with STC, and an RC seven-panel radiator with AZ 93 coating were considered in the ATCS for ISS missions. Two radiator configurations the LM baseline and an RC seven-panel radiator with AZ 93 coating were considered in the ATCS for lunar missions. A Simulink/MATLAB model of the ATCS was used to compute the ATCS performance. Some major hot phases on the thermal timeline were selected because of concern about the large amount of water sublimated for thermal topping. It was concluded that an ATCS with an RC seven-panel radiator could be used for both ISS and lunar missions, but with two different coatings STC for ISS missions and AZ 93 for lunar missions to provide performance similar to or better than that of the LM baseline ATCS.

Wang, Xiao-Yen J.↗

Spaceflight performance of several types of silicon solar cells on the LIPS 3 satellite

Results from exposure of several types of Solarex silicon cells to a space environment for nearly two years on the LIPS 3 satellite are presented. Experiments include standard thickness (10 mil) cells with and without back surface fields, and ultrathin (2 mil) cells also with and without back surface fields. A comparison between a widely used coverslide adhesive, DC 93-500 and a potential alternate is also presented. The major findings from the data are that the 2 mil cells without a back surface field show the smallest normalized short circuit current degradation and that the 10 mil back surface field cells show the greatest absolute power output for the radiation exposures and temperatures encountered. The new encapsulant (McGhan Nusil CV-2500) exhibits a degradation comparable to DC 93-500. A comparison is made with each of the cell types in this experiment with expectations based on JPL Radiation Handbook data.

Silver, J.↗