Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rotor Duct”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Performance and Flowfield Measurements on a 10-inch Ducted Rotor VTOL UAV

A ducted fan VTOL UAV with a 10-inch diameter rotor was tested in the US Army 7-by 10-Foot Wind Tunnel. The test conditions covered a range of angle of attack from 0 to 110 degrees to the freestream. The tunnel velocity was varied from 0 (simulating a hover condition) to 128 ft/sec in propeller mode. A six-component internal balance measured the aerodynamic loads for a range of model configurations. including the isolated rotor, the isolated duct, and the full configuration of the duct and rotor. For some conditions, hotwire velocity surveys were conducted along the inner and outer surface of the duct and across the downstream wake. In addition, fluorescent oil flow visualization allowed the flow separation patterns inside and outside of the duct to be mapped for a few test conditions. Two different duct shapes were tested to determine the performance effects of leading edge radius. For each duct, a range of rotor tip gap from 1%R to 4.5%R was tested to determine the performance penalty in hover and axial flight. Measured results are presented in terms of hover performance, hover performance in a crosswind, and high angle of attack performance in propeller mode. In each case, the effects of both tip gap and duct leading edge radius are illustrated using measurements. Some of the hover performance issues were also studied using a simple analytical method, and the results agreed with the measurements.

Martin, Preston↗
NASA NTRS1974

Theoretical studies on tone noise from a ducted fan rotor

The method of computing radiated noise from a ducted rotor due to inflow distortion and turbulence are examined. Analytical investigations include an appropriate description of sources, the cut-off conditions imposed on the modal propagation of the pressure waves in the annular duct, and reflections at the upstream end of the duct. Far field sound pressure levels at blade passing frequency due to acoustic radiation from a small scale low speed fan are computed. Theoretical predictions are in reasonable agreement with experimental measurements.

Rao, C. V. R.↗
NASA NTRS1976

Aeroacoustics: Fan noise and control; Duct acoustics; Rotor noise

The recent progress in duct acoustic research is reflected by fourteen papers which cover essentially the areas of linear duct acoustics, the characteristics of absorbent materials, and nonlinear duct acoustics. With respect to propagation in ducts, emphasis is placed on computational methods aimed at attaining effective economical modeling of propagation in variable-geometry and in hard-wall or soft-wall ducts. Computational methods developed to reduce computer processing and storage requirements are outlined, along with a wave envelope technique for reducing processing and storage needs. The latter technique is applied to the optimum segmented acoustic duct linear design. A finite difference technique is used in combination with conformal mapping to compute the optimum multisection duct linear design.

Schwartz, I. R.↗
NASA NTRS1998

Broadband Fan Noise Generated by Small Scale Turbulence

This report describes the development of prediction methods for broadband fan noise from aircraft engines. First, experimental evidence of the most important source mechanisms is reviewed. It is found that there are a number of competing source mechanism involved and that there is no single dominant source to which noise control procedures can be applied. Theoretical models are then developed for: (1) ducted rotors and stator vanes interacting with duct wall boundary layers, (2) ducted rotor self noise, and (3) stator vanes operating in the wakes of rotors. All the turbulence parameters required for these models are based on measured quantities. Finally the theoretical models are used to predict measured fan noise levels with some success.

Glegg, Stewart A. L.↗
NASA NTRS1999

Method and apparatus for cold gas reinjection in through-flow and reverse-flow wave rotors

A method and apparatus for cold gas reinjection in through-flow and reverse-flow wave rotors having a plurality of channels formed around a periphery thereof. A first port injects a supply of cool air into the channels. A second port allows the supply of cool air to exit the channels and flow to a combustor. A third port injects a supply of hot gas from the combustor into the channels. A fourth port allows the supply of hot gas to exit the channels and flow to a turbine. A diverting port and a reinjection port are connected to the second and third ports, respectively. The diverting port diverts a portion of the cool air exiting through the second port as reinjection air. The diverting port is fluidly connected to the reinjection port which reinjects the reinjection air back into the channels. The reinjection air evacuates the channels of the hot gas resident therein and cools the channel walls, a pair of end walls of the rotor, ducts communicating with the rotor and subsequent downstream components. In a second embodiment, the second port receives all of the cool air exiting the channels and the diverting port diverts a portion of the cool air just prior to the cool air flowing to the combustor.

Nalim, M. Razi↗
NASA NTRS1997

Numerical Study of Stratified Charge Combustion in Wave Rotors

A wave rotor may be used as a pressure-gain combustor effecting non-steady flow, and intermittent, confined combustion to enhance gas turbine engine performance. It will be more compact and probably lighter than an equivalent pressure-exchange wave rotor, yet will have similar thermodynamic and mechanical characteristics. Because the allowable turbine blade temperature limits overall fuel/air ratio to sub-flammable values, premixed stratification techniques are necessary to burn hydrocarbon fuels in small engines with compressor discharge temperature well below autoignition conditions. One-dimensional, unsteady numerical simulations of stratified-charge combustion are performed using an eddy-diffusivity turbulence model and a simple reaction model incorporating a flammability limit temperature. For good combustion efficiency, a stratification strategy is developed which concentrates fuel at the leading and trailing edges of the inlet port. Rotor and exhaust temperature profiles and performance predictions are presented at three representative operating conditions of the engine: full design load, 40% load, and idle. The results indicate that peak local gas temperatures will result in excessive temperatures within the rotor housing unless additional cooling methods are used. The rotor itself will have acceptable temperatures, but the pattern factor presented to the turbine may be of concern, depending on exhaust duct design and duct-rotor interaction.

Nalim, M. Razi↗
NASA NTRS1990

3D Euler analysis of ducted propfan flowfields

A numerical method is presented for predicting the steady inviscid flow through a ducted propfan based on a time-marching solution of the three-dimensional Euler equations. A four-stage multiple-block Runge-Kutta finite volume numerical technique, utilizing implicit residual smoothing and a blended second and fourth difference dissipation, is applied to predict the transonic flowfield about both single-rotation and counter-rotations ducted rotors. Counter-rotation predictions are based on an average-passage system of equations approach. Calculations are performed for both a single sheared H-type grid system and a multiple-block grid system incorporating a C-type grid about the cowl. Numerical results are compared with experimental data for two cases: a low speed ducted propeller and a 1.15 pressure ratio fan stage.

Hall, Edward J.↗
NASA NTRS1998

A Modified Through-Flow Wave Rotor Cycle with Combustor Bypass Ducts

A wave rotor cycle is described which avoids the inherent problem of combustor exhaust gas recirculation (EGR) found in four-port, through-flow wave rotor cycles currently under consideration for topping gas turbine engines. The recirculated hot gas is eliminated by the judicious placement of a bypass duct which transfers gas from one end of the rotor to the other. The resulting cycle, when analyzed numerically, yields an absolute mean rotor temperature 18% below the already impressive value of the conventional four-port cycle (approximately the turbine inlet temperature). The absolute temperature of the gas leading to the combustor is also reduced from the conventional four-port design by 22%. The overall design point pressure ratio of this new bypass cycle is approximately the same as the conventional four-port cycle. This paper will describe the EGR problem and the bypass cycle solution including relevant wave diagrams. Performance estimates of design and off-design operation of a specific wave rotor will be presented. The results were obtained using a one-dimensional numerical simulation and design code.

Paxson Daniel E.↗
NASA NTRS1974

Three-dimensional flow in transonic axial compressor blade rows

Recent developments in the three-dimensional aerodynamic theory of inviscid flow in transonic axial compressors are reviewed. Emphasis is placed on the newly completed lifting surface theory of a transonic ducted rotor. The relationship between the lifting surface theory and axisymmetric through-theories of turbomachines is illustrated; a few examples of the additional information obtainable from the new theory are then given. Quasi-two-dimensional cascade theory can also be extracted from the present analysis and the relevance of cascade theory to the actual three-dimensional problem assessed. Details are reported elsewhere, but some of the qualitative conclusions are discussed here. Even moderate departure from uniform spanwise loading of the rotor blades, for example, leads to a rather profound influence of the downstream wakes, suggesting the need for considerable care in applying cascade data on a direct quasi-two-dimensional basis.

Mccune, J. E.↗
NASA NTRS1982

Development of secondary flow and vorticity in curved ducts, cascades, and rotors, including effects of viscosity and rotation

This paper is concerned with the numerical solution of the secondary vorticity equations in curved ducts, cascades, and rotors. The classical approach of splitting the flow into primary and secondary flow fields is employed and extended to include effects of viscosity, rotation, and density stratification. All elliptical effects are neglected and the Crank-Nicolson method is used to solve the secondary vorticity equation. The secondary flow field is obtained by solving a Poisson equation using a successive over-relaxation method. The results are compared with theoretical and experimental data from stationary ducts, compressor and turbine cascades. The agreement is good for most of the cases.

Pouagare, M.↗
NASA NTRSDate not supplied

Optimization of Variable Depth Acoustic Liners with Grazing Flow

Acoustic liners, typically used as a noise control treatment in the engine nacelles of conventional aircraft, are being considered for noise treatment in the proprotor ducts of a vertical takeoff and landing aircraft. This work considers a new optimization method to design an acoustic liner with variable depth cavities for broadband and low-frequency attenuation. This method, termed the direct optimization method, minimizes the radiated sound from a duct. In this paper, the new method is compared with an existing indirect method to design multiple variable depth acoustic liners. Acoustic impedances of liners designed using both methods are predicted using a semianalytical impedance model and impedance predictions for two designs are compared to experimental results acquired from grazing flow impedance testing. For the work presented here, liners designed using the indirect approach provide improved attenuation spectra over those designed using the direct approach but potential improvements to the performance of the direction optimization method are discussed.

Proprotor↗
NASA NTRS2012

Validation of the Predicted Circumferential and Radial Mode Sound Power Levels in the Inlet and Exhaust Ducts of a Fan Ingesting Distorted Inflow

Fan inflow distortion tone noise has been studied computationally and experimentally. Data from two experiments in the NASA Glenn Advanced Noise Control Fan rig have been used to validate acoustic predictions. The inflow to the fan was distorted by cylindrical rods inserted radially into the inlet duct one rotor chord length upstream of the fan. The rods were arranged in both symmetric and asymmetric circumferential patterns. In-duct and farfield sound pressure level measurements were recorded. It was discovered that for positive circumferential modes, measured circumferential mode sound power levels in the exhaust duct were greater than those in the inlet duct and for negative circumferential modes, measured total circumferential mode sound power levels in the exhaust were less than those in the inlet. Predicted trends in overall sound power level were proven to be useful in identifying circumferentially asymmetric distortion patterns that reduce overall inlet distortion tone noise, as compared to symmetric arrangements of rods. Detailed comparisons between the measured and predicted radial mode sound power in the inlet and exhaust duct indicate limitations of the theory.

Koch, L. Danielle↗
NASA NTRS2001

Predicting the Rotor-Stator Interaction Acoustics of a Ducted Fan Engine

A Navier-Stokes computation is performed for a ducted-fan configuration with the goal of predicting rotor-stator noise generation without having to resort to heuristic modeling. The calculated pressure field in the inlet region is decomposed into classical infinite-duct modes, which are then used in either a hybrid finite-element/Kirchhoff surface method or boundary integral equation method to calculate the far field noise. Comparisons with experimental data are presented, including rotor wake surveys and far field sound pressure levels for two blade passage frequency (BPF) tones.

Biedron, Robert T.↗
NASA NTRS2001

Predicting the Rotor-Stator Interaction Acoustics of a Ducted Fan Engine

A Navier-Stokes computation is performed for a ducted-fan configuration with the goal of predicting rotor-stator noise generation without having to re- to heuristic modeling. The calculated pressure field in the inlet region is decomposed into classical infinite-duct, modes, which are then used in either a hybrid finite-element /Kirchhoff surface method or boundary integral equation method to calculate the far field noise. Comparisons with experimental data are presented, including rotor wake surveys and far field sound pressure levels for 2 blade passage frequency (BPF) tones.

Biedron, Robert T.↗
NASA NTRS1993

An iterative multidisciplinary analysis for rotor blade shape determination

A CFD solver called ADPAC-APES is coupled with a NASTRAN structural analysis and a MARC thermal/heat transfer analysis to determine rotor blade shape. Nonlinear blade displacements due to centrifugal loads, aerodynamic pressures, and nonuniform temperature distribution are determined simultaneously. The effect of blade displacements on aerodynamic pressures and temperatures is then analyzed. These calculations are iterated till a steady state is reached across all the disciplines. This iterative procedure is applied to a ducted fan rotor blade and the manufactured shape is determined from a given operating shape. Effect of a part-span shroud on blade deflections is also analyzed.

Mahajan, Aparajit J.↗
NASA NTRS1954

Aspects of internal-flow-system design for helicopter propulsive units

Pertinent items relating to the design of internal-flow systems for reciprocating engine, turbine engine, and pressure-jet installations in helicopters are discussed. The importance of the following items is emphasized: controllable exit and ram recovery for reciprocating-engine cooling; performance penalties possible in turbine-engine installations attributed to distortions in the flow distribution at the face of the axial compressor; the effects of high subsonic flow velocities on the performance of duct elements; and the effects of centrifugal forces on the flow in a ducted helicopter rotor. Data on the maximum flow capacities of bends are included.

John R Henry↗
NASA NTRS1975

Broadband noise generated by turbulent inflow to rotor or stator blades in an annular duct

The Green's function relating the radiated pressure field to the fluctuating forces on rotor or stator blades is developed in the presence of dissipation due to turbulent velocity fluctuations and sound speed fluctuations. The resonances in the output power spectrum which would occur at the cut-off frequencies in the absence of dissipation should be removed and smeared out by the incorporation of dissipation. Wave number dependence is developed for an effective eddy viscosity due to the aforementioned fluctuations in the background medium. The space-time correlation function for blade-normal velocity fluctuations on a single or on two different blades is developed in terms of the velocity correlation tensor for the inflow under the assumptions of isotropy and (Taylor) frozen behavior. The correlation function is then simplified under certain approximations and the behavior of the blade-force correlation function is inferred.

Lnae, F.↗
NASA NTRS2016

Coaxial Compound Helicopter for Confined Urban Operations

A rotorcraft was designed for military operations in a confined urban environment. The specifications included major increases in useful load, range, and speed relative current aircraft capabilities, with a size constraint based on the dimensions of urban streets and intersections. Analysis showed that this combination of requirements is best satisfied by a coaxial main-rotor configuration, with lift compounding to off-load the rotors at high speed, and ducted fans under the rotor disk for propulsion. The baseline design is described, and the aircraft performance is summarized for utility, attack, MEDEVAC, and cargo delivery missions. The impact on size and performance is examined for a number of excursions, including lift-offset main rotors. Technology development required to achieve this advance in capability is recommended.

Urban Operations↗