Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Remote Gas Sensors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

New Remote Gas Sensor Using Rapid Electro-Optical Path Switching

Innovative gas filter correlation radiometer (GFCR) features nonmechanical switching of internal optical paths. Incoming radiation switched electro-optically, by means of polarization, between two optical paths, one of which contains correlation gas cell while other does not. Advantages include switching speed, 2 to 3 orders of magnitude faster than mechanical techniques, and high reliability. Applications include regional studies of atmospheric chemistry from either manned or unmanned aircraft as well as satellite studies of global distributions, sources and sink mechanisms for key species involved in chemistry of troposphere. Commercial applications: ability to survey many miles of natural gas pipelines rapidly from aircraft, pinpointing gas leaks by measuring methane at 2.3 micrometers.

Sachse, G. W.↗
NASA NTRS1978

Aircraft instrumentation system for the remote sensing of carbon monoxide

A light twin-engine aircraft has been instrumented with a carbon monoxide remote gas sensor system and test flown over the Southern Lake Michigan basin during August, 1976. The remote sensor is based on the gas filter correlation technique. The radiance levels from the sensor along with the data on the surface temperature, air temperature, dewpoint, and altitude were digitized and recorded on seven-track magnetic tape. Air samples were collected at various altitudes over selected sites for later analysis of carbon monoxide concentration and comparison with the inferred concentration from the remote sensor. The values of carbon monoxide obtained from the air samples and the values inferred from the remote sensor for data collected over water are in good agreement.

Beck, S. M.↗
NASA NTRS1981

Data reduction analysis and application technique development for atmospheric trace gas constituents derived from remote sensors on satellite or airborne platforms

The applicability of the gas filter correlation radiometer (GFCR) to the measurement of tropospheric carbon monoxide gas was investigated. An assessment of the GFRC measurement system to a regional measurement program was conducted through extensive aircraft flight-testing of several versions of the GFRC. Investigative work in the following areas is described: flight test planning and coordination, acquisition of verifying CO measurements, determination and acquisition of supporting meteorological data requirements, and development of supporting computational software.

Casas, J. C.↗
NASA NTRS1983

Investigation of forestry resources and other remote sensing data. 1: LANDSAT. 2: Remote sensing of volcanic emissions

Computer classification of LANDSAT data was used for forest type mapping in New England. The ability to classify areas of hardwood, softwood, and mixed tree types was assessed along with determining clearcut regions and gypsy moth defoliation. Applications of the information to forest management and locating potential deer yards were investigated. The principal activities concerned with remote sensing of volcanic emissions centered around the development of remote sensors for SO2 and HCl gas, and their use at appropriate volcanic sites. Two major areas were investigated (Masaya, Nicaragua, and St. Helens, Washington) along with several minor ones.

Birnie, R. W.↗
NASA NTRS1996

Efficient, Narrow-Pass-Band Optical Filters

Optical filters with both narrow pass bands and high efficiencies fabricated to design specifications. Offer tremendous improvements in performance for number of optical (including infrared) systems. In fiber-optic and free-space communication systems, precise frequency discrimination afforded by narrow pass bands of filters provide higher channel capacities. In active and passive remote sensors like lidar and gas-filter-correlation radiometers, increased efficiencies afforded by filters enhance detection of small signals against large background noise. In addition, sizes, weights, and power requirements of many optical and infrared systems reduced by taking advantage of gains in signal-to-noise ratios delivered by filters.

Sandford, Stephen P.↗
NASA NTRS1979

Evaluation of atmospheric trace constituent sensors operating from remote space and airborne platforms

A laboratory gas analysis system was developed specifically to make trace level measurements of carbon monoxide. To assure that the data collected with this system are correctly aligned with other established methods for making these measurements, an intercalibration study was conducted. The calibration gas was analyzed by the various participating laboratories and found to contain 1.28 ppm CO. Samples were collected at 25 deg, 35 deg, and 45 deg N for profile data to study the variation in concentrations of CO and CH4 as a function of altitude and latitude in continental air over the eastern seaboard of the United States. The experiment was repeated several months later to determine if there were seasonally dependent variations in the CO and CH4 concentrations.

Condon, E.↗
NASA NTRS2012

NASA Tech Briefs, April 2012

Topics include: Computational Ghost Imaging for Remote Sensing; Digital Architecture for a Trace Gas Sensor Platform; Dispersed Fringe Sensing Analysis - DFSA; Indium Tin Oxide Resistor-Based Nitric Oxide Microsensors; Gas Composition Sensing Using Carbon Nanotube Arrays; Sensor for Boundary Shear Stress in Fluid Flow; Model-Based Method for Sensor Validation; Qualification of Engineering Camera for Long-Duration Deep Space Missions; Remotely Powered Reconfigurable Receiver for Extreme Environment Sensing Platforms; Bump Bonding Using Metal-Coated Carbon Nanotubes; In Situ Mosaic Brightness Correction; Simplex GPS and InSAR Inversion Software; Virtual Machine Language 2.1; Multi-Scale Three-Dimensional Variational Data Assimilation System for Coastal Ocean Prediction; Pandora Operation and Analysis Software; Fabrication of a Cryogenic Bias Filter for Ultrasensitive Focal Plane; Processing of Nanosensors Using a Sacrificial Template Approach; High-Temperature Shape Memory Polymers; Modular Flooring System; Non-Toxic, Low-Freezing, Drop-In Replacement Heat Transfer Fluids; Materials That Enhance Efficiency and Radiation Resistance of Solar Cells; Low-Cost, Rugged High-Vacuum System; Static Gas-Charging Plug; Floating Oil-Spill Containment Device; Stemless Ball Valve; Improving Balance Function Using Low Levels of Electrical Stimulation of the Balance Organs; Oxygen-Methane Thruster; Lunar Navigation Determination System - LaNDS; Launch Method for Kites in Low-Wind or No-Wind Conditions; Supercritical CO2 Cleaning System for Planetary Protection and Contamination Control Applications; Design and Performance of a Wideband Radio Telescope; Finite Element Models for Electron Beam Freeform Fabrication Process Autonomous Information Unit for Fine-Grain Data Access Control and Information Protection in a Net-Centric System; Vehicle Detection for RCTA/ANS (Autonomous Navigation System); Image Mapping and Visual Attention on the Sensory Ego-Sphere; HyDE Framework for Stochastic and Hybrid Model-Based Diagnosis; and IMAGESEER - IMAGEs for Education and Research.

Source record↗
NASA NTRS2020

Evaluation of NASA’s Remote-Sensing Capabilities in Coastal Environments

This work represents the second part of a two-part study set up by the National Aeronautics and Space Administration (NASA) and Bureau of Ocean Energy Management (BOEM) in 2017. The study summarizes a three-year investigation on the feasibility of using satellite remote sensing to monitor emissions of oil and gas operations over the outer continental shelf (OCS) to determine if they have negative impacts on coastal air quality (AQ). The target pollutant is nitrogen dioxide (NO2), for which BOEM conducts regular emissions surveys. The major data source for this report is a May 2019 oceanographic cruise (“SCOAPE” = Satellite Coastal and Oceanic Atmospheric Pollution Experiment) conducted in the Gulf of Mexico (GoM) off Louisiana with the Research Vessel Point Sur, loaded with a suite of trace-gas analyzers and a direct-sun remote sensor Pandora spectrometer that measures column NO2. The SCOAPE cruise, augmented by in situ NO2 and Pandora measurements at Cocodrie (Louisiana; 29.25° N, 90.66° W) showed that (1) under cloud-free conditions, satellites can detect elevated column NO2 amounts near isolated large platforms and from clusters of smaller operations; (2) satellite (the European Space Agency’s TROPOspheric Monitoring Instrument [TROPOMI]) total column (TC) NO2 agrees well with TC NO2 from ground-based Pandora spectrometers (to 11–18%), with the satellite biased low when pollution levels are higher; (3) in general, NO2 measured in situ and in column amounts by Pandora or TROPOMI is greater over coastal Louisiana than over the OCS; (4) the extent to which Pandora or satellite measurements correlate with surface NO2 is highly variable.

NO2↗
NASA NTRS1990

In situ ozone measurements for the airborne arctic stratospheric experiment

The research provided in-situ ozone measurements onboard the NASA Ames DC-8 research aircraft during the 1989 Airborne Arctic Stratospheric Experiment. The Ames DC-8 and ER-2 aircraft performed extensive sampling of the Arctic stratosphere and troposphere in a program designed to study those factors important in ozone depletion in the Arctic during times when the polar vortex and meteorology are conducive to the formation of polar stratospheric clouds and/or an Arctic ozone hole. The DC-8 ozone instrument complement included in-situ measurements for H2O, NO, NO2, NO(y) gas, NO(y) particulate, as well as remote sensors for measuring the vertical distribution and column density of ozone above the aircraft altitude. The in-situ data (ozone, water vapor, and nitrogen species) at the aircraft altitude provide a definition of tropospheric conditions in the vicinity of the polar vortex and polar stratospheric clouds. Defining tropospheric conditions will assist in the understanding of the chemistry of both stratosphere and troposphere and the extent to which polar stratospheric clouds affect the chemistry of transported air.

Gregory, Gerald L.↗
NASA NTRS1975

A theoretical/experimental program to develop active optical pollution sensors: Quantitative remote Raman lidar measurements of pollutants from stationary sources

Typical pollutant gas concentrations at the stack exits of stationary sources can be estimated to be about 500 ppm under the present emission standards. Raman lidar has a number of advantages which makes it a valuable tool for remote measurements of these stack emissions. Tests of the Langley Research Center Raman lidar at a calibration tank indicate that night measurements of SO2 concentrations and stack opacity are possible. Accuracies of 10 percent are shown to be achievable from a distance of 300 m within 30 min integration times for 500 ppm SO2 at the stack exits. All possible interferences were examined quantitatively (except for the fluorescence of aerosols in actual stack emissions) and found to have negligible effect on the measurements. An early test at an instrumented stack is strongly recommended.

Poultney, S. K.↗
NASA NTRS1986

Middle and upper tropospheric carbon monoxide mixing ratios as measured by a satellite-borne remote sensor during November 1981

Mixing ratios of tropospheric carbon monoxide measured by a gas filter radiometer carried aboard the Space Shuttle during November 1981 are reported. The data represent average mixing ratios in the middle and upper troposphere between 38 deg N and 38 deg S latitude. Approximately 10,000 individual measurements were obtained in each of the two channels of the instrument. The data are presented in the form of plots that show the individual carbon monoxide mixing ratio measurements as a function of latitude and longitude and in the form of maps that show the data averaged over 5 deg latitude by 5 deg longitude squares. The data show relatively little variation in the mixing ratio in the Southern Hemisphere; however, the data from both the tropics and the Northern Hemisphere show strong gradients with both latitude and longitude.

Reichle, H. G., Jr.↗
NASA NTRS1983

Cascade Joule-Thomson refrigerators

The design criteria for cascade Joule-Thomson refrigerators for cooling in the temperature range from 300 K to 4.2 K were studied. The systems considered use three or four refrigeration stages with various working gases to achieve the low temperatures. Each stage results in cooling to a progressively lower temperature and provides cooling at intermediate temperatures to remove the substantial amount of parasitic heat load encountered in a typical dewar. With careful dewar design considerable cooling can be achieved with moderate gas flows. For many applications, e.g., in the cooling of sensitive sensors, the fact that the refrigerator contains no moving parts and may be remotely located from the gas source is of considerable advantage. A small compressor suitable for providing the gas flows required was constructed.

Tward, E.↗
NASA NTRSDate not supplied

Fast Radiative Transfer Model and Retrieval Algorithm Development for Satellite Remote Sensing Applications

The radiative transfer model (RTM) has a wide range of applications in satellite remote sensing and atmospheric radiation studies. For example, it can be used as a forward model for an inversion algorithm and a satellite data assimilation system, or as a L1 data simulator for pre-launch end-to-end satellite sensor performance studies. However, millions of line-by-line (LBL) radiative transfer calculations at fine monochromatic frequencies are needed in order to properly calculate spectral contributions of water vapor and trace gases in the atmosphere in infrared and solar spectral regions. Therefore, fast, and accurate radiative transfer models are needed. A Principal Component-based radiative transfer model (PCRTM) was developed at NASA Langley to fulfil this need. The PCRTM can simulate the top-of-atmosphere (TOA) radiance or reflectance spectra from 250 nm to 2000 micrometers with several orders of magnitude faster speed as compared to a LBL RTM. It is also extremely accurate compared to LBL RTM benchmarks. The PCRTM model has been developed for hyperspectral sensors such as AIRS, CrIS, IASI, NAST-I, SHIS, CPF, TEMPO, EMIT, OMI, and SCIAMACHY. By using the PCRTM as forward model for an inversion algorithm, one can reduce the data dimension significantly while maintaining original information content by compressing the TOA radiance spectrum into PC-scores. The PCRTM can directly compute the PC-scores and their derivatives with respect to retrieved parameters. Examples of using various PCRTM inversion algorithms to retrieve atmospheric temperature, water vapor, and trace gas profiles, as well as cloud and surface properties from satellite hyperspectral remote sensors will be given. Some of the algorithms have been transitioned to NASA's Goddard Earth Sciences Data and Information Services Center (GES DISC) for public access of high-quality L2 and L3 data.

Xu Liu↗
NASA NTRS1984

Portable remote laser sensor for methane leak detection

A portable laser system for remote detection of methane gas leaks and concentrations is disclosed. The system transmitter includes first and second lasers, tuned respectively to a wavelength coincident with a strong absorption line of methane and a reference wavelength which is weakly absorbed by methane gas. The system receiver includes a spherical mirror for collecting the reflected laser radiation and focusing the collected radiation through a narrowband optical filter onto an optial detector. The filter is tuned to the wavelength of the two lasers, and rejects background noise. The output of the optical detector is processed by a lock-in detector synchronized to the chopper, and which measures the difference between the first wavelength signal and the reference wavelength signal.

Grant, W. B.↗
NASA NTRS2004

New Hydrophilic, Composite Membranes for Air Removal from Water Coolant Systems

Liquid coolants are commonly used as thermal transport media to increase efficiency and flexibility in aerospace vehicle design. The introduction of gas bubbles into the coolant can have negative consequences, including: loss of centrifugal pump prime, irregular sensor readings, and blockage of coolant flow to remote systems. One solution to mitigate these problems is the development of a passive gas removal device, or gas trap, installed in the flight cooling system. In this study, a new hydrophilic, composite membrane has been developed for passage of the coolant fluid and retention of gas bubbles. The trapped bubbles are subsequently vented from the system by a thin, hydrophobic, microporous membrane. The original design for this work employed a homogeneous membrane that was susceptible to fouling and pore plugging. Spare gas traps of this variety have degraded during storage, and recreation of the membranes has been complicated due to problems with polymer duplication and property variations in the final membranes. In this work, replacements have been developed based on deposition of a hydrophilic polymer on the bore-side of a porous polyethylene (PE) tube. The tube provides excellent chemical and mechanical stability, and the hydrophilic layer provides retention of gas bubbles. Preliminary results have shown that intimate contact is required between the deposited layer and the substrate to overcome material differences. This has been accomplished by presoaking the membrane tube in the solvent to raise its surface energy. Polymer solutions of various concentrations have been used to promote penetration of the polymer layer into the porous substrate and to control separation layer thickness. The resulting composite membranes have shown repeatable decrease in nitrogen permeability, which is indicative of a decrease in membrane pore size. Studies with water permeation have yielded similar results. We have observed some swelling of the added polymer layer, which causes a slight decrease in membrane pore size, and should result in improved bubble retention. Preliminary studies have also been performed on gas retention in flowing systems. Initial results have been promising, with negligible gas permeation for the coated membranes compared to 100% gas permeation in the uncoated tube.

Ritchie, Stephen M. C.↗
NASA NTRS1981

Exploration for fractured petroleum reservoirs using radar/Landsat merge combinations

Since fractures are commonly propagated upward and reflected at the earth's surface as subtle linears, detection of these surface features is extremely important in many phases of petroleum exploration and development. To document the usefulness of microwave analysis for petroleum exploration, the Arkansas part of the Arkoma basin is selected as a prime test site. The research plan involves comparing the aircraft microwave imagery and Landsat imagery in an area where significant subsurface borehole geophysical data are available. In the northern Arkoma basin, a positive correlation between the number of linears in a given area and production from cherty carbonate strata is found. In the southern part of the basin, little relationship is discernible between surface structure and gas production, and no correlation is found between gas productivity and linear proximity or linear density as determined from remote sensor data.

Macdonald, H.↗
NASA NTRSDate not supplied

Gulf of Mexico Health & Air Quality: Mapping Methane Emission Plumes Using Sunglint-configured Imagery for Monitoring Offshore Oil and Gas Activity

We had three project objectives that we set out to accomplish. The first objective is to demonstrate how remote sensing can complement the current bottom-up methane emission assessments. Currently, quantities of disposed gas vented and flared are self-reported by operators to BOEM and BSEE. Meanwhile, inspections are uncommon, and ground sensors are non-existent. Therefore, remote sensing may be the agencies' best bet in verifying these operator accounts. The second objective is to identify methane plumes in the Gulf of Mexico, Asia, and elsewhere using Sentinel-2, LandSat, and PRISMA images, and then present an estimate of their emission rate. While methane retrievals from oil and gas infrastructure on-shore has been relatively well-documented, doing so on the offshore oil and gas platforms is more difficult, less prevalent, and contingent on the presence of specific conditions. The final objective is to give our partners, BOEM and BSEE, a more robust understanding of methane emissions from oil and gas production in the Gulf of Mexico. This increased knowledge, paired with a demonstration of methane monitoring, is intended to help our partners think about how they can incorporate remote sensing into their monitoring, regulatory and enforcement framework.

Ben Dahan↗