Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Radiative recombination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Over 31% efficient indoor organic photovoltaics enabled by simultaneously reduced trap-assisted recombination and non-radiative recombination voltage loss

Indoor organic photovoltaics (OPVs) have shown great potential application in driving low-energy-consumption electronics for the Internet of Things. There is still great room for further improving the power conversion efficiency (PCE) of indoor OPVs, considering that the desired morphology of the active layer to reduce trap-assisted recombination and voltage losses and thus simultaneously enhance the fill factor (FF) and open-circuit voltage for efficient indoor OPVs remains obscure. Herein, by optimizing the bulk and interface morphology via a layer-by-layer (LBL) processing strategy, low leakage current and low non-radiative recombination loss can be synergistically achieved in PM6:Y6-O based devices. Detailed characterizations reveal the stronger crystallinity, purer domains and ideal interfacial contacts in the LBL devices compared to their bulk-heterojunction (BHJ) counterparts. The optimized morphology yields a reduced voltage loss and an impressive FF of 81.5%, and thus contributes to a high PCE of 31.2% under a 1000 lux light-emitting diode (LED) illumination in the LBL devices, which is the best reported efficiency for indoor OPVs. Additionally, this LBL strategy exhibits great universality in promoting the performance of indoor OPVs, as exemplified by three other non-fullerene acceptor systems. Finally, this work provides guidelines for morphology optimization and synergistically promotes the fast development of efficient indoor OPVs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Geometric and doping effects on radiative recombination in thin-film near-field energy converters

Modeling radiative recombination is crucial to the analysis of radiative energy converters. In this work, a local radiative recombination coefficient is defined and derived based on fluctuational electrodynamics that is applicable to thin-film cells in both the near field and far field. The predicted radiative recombination coefficient of an InAs cell deviates from the van Roosbroeck–Shockley relation when the thickness is less than 10 µm, and the difference exceeds fourfold with a 10 nm film. The local radiative recombination coefficient is orders of magnitude higher when an InAs cell is configured in the near field. The local radiative recombination coefficient reduces as the doping level approaches that of a degenerate semiconductor. The maximum output power and efficiency of a thermoradiative cell would be apparently overpredicted if the electroluminescence coefficient defined in this paper were taken as unity for heavily doped semiconductors.

Feng, Dudong↗
DOE OSTI2023

19.31% binary organic solar cell and low non-radiative recombination enabled by non-monotonic intermediate state transition

Non-fullerene acceptors based organic solar cells represent the frontier of the field, owing to both the materials and morphology manipulation innovations. Non-radiative recombination loss suppression and performance boosting are in the center of organic solar cell research. Here, we developed a non-monotonic intermediate state manipulation strategy for state-of-the-art organic solar cells by employing 1,3,5-trichlorobenzene as crystallization regulator, which optimizes the film crystallization process, regulates the self-organization of bulk-heterojunction in a non-monotonic manner, i.e., first enhancing and then relaxing the molecular aggregation. As a result, the excessive aggregation of non-fullerene acceptors is avoided and we have achieved efficient organic solar cells with reduced non-radiative recombination loss. In PM6:BTP-eC9 organic solar cell, our strategy successfully offers a record binary organic solar cell efficiency of 19.31% (18.93% certified) with very low non-radiative recombination loss of 0.190 eV. And lower non-radiative recombination loss of 0.168 eV is further achieved in PM1:BTP-eC9 organic solar cell (19.10% efficiency), giving great promise to future organic solar cell research.

14 SOLAR ENERGY↗
DOE OSTI2023

B—N–Bond–Embedded Triplet Terpolymers with Small Singlet–Triplet Energy Gaps for Suppressing Non–Radiative Recombination and Improving Blend Morphology in Organic Solar Cells

Suppressing the photon energy loss (E loss ), especially the non-radiative loss, is of importance to further improve the device performance of organic solar cells (OSCs). However, typical π-conjugated semiconductors possess a large singlet–triplet energy gap (ΔE ST ), leading to a lower triplet state than charge transfer state and contributing to a non-radiative loss channel of the photocurrent by the triplet state. Herein, a series of triplet polymer donors are developed by introducing a BNIDT block into the PM6 polymer backbone. Further, the high electron affinity of BNIDT and the opposite resonance effect of the B—N bond in BNIDT results in a lowered highest occupied molecular orbital (HOMO) and a largely reduced ΔE ST . Moreover, the morphology of the active blends is also optimized by fine-tuning the BNIDT content. Therefore, non-radiative recombination via the terminal triplet loss channels and morphology traps is effectively suppressed. The PNB-3 (with 3% BNIDT):L8-BO device exhibits both small ΔE ST and optimized morphology, favoring more efficient charge transfer and transport. Finally, the simultaneously enhanced V oc of 0.907 V, J sc of 26.59 mA cm –2 , and FF of 78.86% contribute to a champion PCE of 19.02%. Therefore, introducing B—N bonds into benchmark polymers is a possible avenue toward higher-performance of OSCs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Laser-assisted radiative recombination in a cold hydrogen plasma

Abstract We study the process of laser-assisted radiative recombination of an electron with a proton in a cold hydrogen plasma employing the semiclassical Kramers’ approach which involves calculation of classical trajectories in combined laser and Coulomb fields and the use of the correspondence principle. Due to the Coulomb focusing effect, recombination is the most effective when the initial electron momentum is parallel to the laser polarization. Orders of magnitude enhancement of the cross section, as compared to the laser-free case, is observed in this case. With increasing angle between the electron momentum and polarization, the recombination cross section drops. However, even after averaging over Maxwellian velocity distribution we obtain a substantial enhancement of the recombination rate constant, as compared to the zero-field case. For the field intensities in the range 30–350 MW cm −2 , the enhancement occurs in the region of the radiation wavelength from 5 to 20 µ m and for the plasma temperature from 20 to 300 K.

Fabrikant, I. I. (ORCID:0000000293849454)↗
DOE OSTI2025

𝐴𝑏 initio density-matrix approach to exciton coherence: Phonon scattering, Coulomb interactions, and radiative recombination

Relaxation processes following light excitation in semiconductors are key in materials-based quantum technology applications. These processes are broadly studied in atomically thin transition-metal dichalcogenides, quasi-two-dimensional excitonic semiconductors in which atomistic design allows for tunable excited-state properties, such as relaxation lifetimes and photoinduced coherence. In this work, we present a density-matrix-based approach to compute exciton relaxation within a many-body ab initio perspective. We expand our previously developed Lindblad density-matrix formalism to capture multichannel electron-hole pair relaxation processes, including phonon and Coulomb scattering as well as radiative recombination, and we study their effect on the time-resolved excited-state propagation. Using monolayer MoSe 2 as a prototypical example, we examine many-body effects on the time-dependent dynamics of photoactive excitations, exploring how the electron-hole pair interactions are reflected in variations of the excitation energy, spectral signature, and state coherence. In conclusion, our method supplies a detailed understanding of exciton relaxation mechanisms in realistic materials, offering a previously unexplored pathway to study excited-state dynamics in semiconductors from first principles.

Band structure methods↗
DOE OSTI2022

Acceleration of Biexciton Radiative Recombination at Low Temperature in CdSe Nanoplatelets

Colloidal semiconductor nanocrystals offer bandgap tunability, high photoluminescence quantum yield, and colloidal processing of benefit to optoelectronics, however rapid nonradiative Auger recombination (AR) deleteriously affects device efficiencies at elevated excitation intensities. AR is understood to transition from temperature-dependent behavior in bulk semiconductors to temperature-independent behavior in zero-dimensional quantum dots (QDs) as a result of discretized band structure that facilitates satisfaction of linear momentum conservation. For nanoplatelets (NPLs), two-dimensional morphology renders prediction of photophysical behaviors challenging. Here, in this study, we investigate and compare the temperature dependence of excited-stated lifetime and fluence-dependent emission of CdSe NPLs and QDs. For NPLs, upon temperature reduction, biexciton lifetime surprisingly decreases (even becoming shorter lived than trion emission) and emission intensity increases nearly linearly with fluence rather than saturating, consistent with dominance of radiative recombination rather than AR. CdSe NPLs thus differ fundamentally from core-only QDs and foster increased utility of photogenerated excitons and multiexcitons at low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Lower limits for non-radiative recombination loss in organic donor/acceptor complexes

Understanding the factors controlling radiative and non-radiative transition rates for charge transfer states in organic systems is important for applications ranging from organic photovoltaics (OPV) to lasers and LEDs. Here we explore the role of charge-transfer (CT) energetics, lifetimes, and photovoltaic properties in the limit of very slow non-radiative rates by using a model donor/acceptor system with photoluminescence dominated by thermally activated delayed fluorescence (TADF). This blend exhibits an extremely high photoluminescence quantum efficiency (PLQY = ~22%) and comparatively long PL lifetime, while simultaneously yielding appreciable amounts of free charge generation (photocurrent external quantum efficiency EQE of 24%). In solar cells, this blend exhibits non-radiative voltage losses of only ~0.1 V, among the lowest reported for an organic system. Notably, we find that the non-radiative decay rate, k nr , is on the order of 10 5 s -1 , approximately 4–5 orders of magnitude slower than typical OPV blends, thereby confirming that high radiative efficiency and low non-radiative voltage losses are achievable by reducing k nr . Furthermore, despite the high radiative efficiency and already comparatively slow k nr , we find that k nr is nevertheless much faster than predicted by Marcus–Levich–Jortner two-state theory and we conclude that CT-local exciton (LE) hybridization is present. Our findings highlight that it is crucial to evaluate how radiative and non-radiative rates of the LE states individually influence the PLQY of charge-transfer states, rather than solely focusing on the PLQY of the LE. This conclusion will guide material selection in achieving low non-radiative voltage loss in organic solar cells and high luminescence efficiency in organic LEDs.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Reducing Non-Radiative Recombination in Perovskite Solar Cells with a SiO2-Graphene Oxide Buried Interface Layer

Perovskite solar cells (PSCs) have emerged as a transformative photovoltaic technology. However, the device performance of inverted PSCs is dramatically limited by surface defects and the underlying film morphology of metal halide perovskite (MHP) thin film. Herein, we report a novel buried interface layer consisting of SiO2 nanoparticles (NPs) chemically bonded to graphene oxide (GO), deposited atop a hydrophobic hole extraction layer (HEL) to address this limitation. The SiO2 NPs serve as insoluble scaffolds that immobilize GO sheets on the hydrophobic HEL surface, enabling the formation of homogeneous MHP thin films. Meanwhile, the GO functional groups interact with surface-uncoordinated Pb2+, suppressing interfacial defects and guiding crystal grain growth of the resultant MHP thin films. This synergistic effect suppresses non-radiative charge recombination and enhances charge extraction efficiency. As a result, a 26.07% efficiency with significantly suppressed photocurrent hysteresis is observed from PSCs incorporating the SiO2-GO buried interface layer. Moreover, the above PSCs maintain 92% of their initial PCE after 1800 h of continuous operation at the maximum power point under AM 1.5 G (100 mW/cm2) illumination at 25 degrees C in air with 50-60% relative humidity. These results demonstrate that we have developed a facile and effective way to realize high-performance inverted PSCs.

14 SOLAR ENERGY↗
DOE OSTI2025

Self-Trapped-Exciton Radiative Recombination in β–Ga 2 O 3 : Impact of Two Concurrent Nonradiative Auger Processes

The peculiarities of radiative and nonradiative processes associated with self-trapped intrinsic eXcitons in the excited β-Ga 2 O 3 crystals are studied via time-resolved techniques of induced absorption, transient grating, and photoluminescence (PL) at room temperature. The excitation above the bandgap is produced by laser pulses with linear light polarization parallel and orthogonal in the (–201) and (001) planes. We elucidate that the nonradiative recombination rate occurring in the eXciton prevails over its radiative emission rate in a wide range of free carrier concentration composed of excited and equilibrium electrons. Hence, the nonradiative recombination has no effect on the strong anisotropy and the shape of the eXciton emission band. However, we find out that the conventional ABC model of electron effective lifetime is insufficient for explanation of the excitation dependences. Inclusion of two nonradiative Auger mechanisms in a modified ABC formula provides excellent agreement of these dependences. We conclude that the trap-assisted Auger process is in proportion to the free electron density with coefficient B = 1.1 × 10 –11 cm 3 /s and appears at low/intermediate excitation, while the triple-particle Auger process is in proportion to Δn 2 with coefficient C = 8 × 10 –30 cm 6 /s and appears at high excitation conditions. The transition between two Auger mechanisms is accompanied by a rise of the eXciton diffusivity in preferred crystallographic directions where the radiative PL intensity is maximal. The diffusion length LD in these directions can reach values ~300 nm, but, at high excitations, LD becomes limited by Auger lifetimes. These findings pave the way for the implementation of self-trapped eXcitons into specific optoelectronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Improved Radiative Recombination in AlInGaP LEDs

Direct-emitting red and amber LEDs based on the AlInGaP material system offer a higher efficacy potential than phosphor-converted (pc) red and amber LEDs due to the absence of Stokes losses. Direct red LEDs (~610-620nm) are increasingly used in color-mixed and color-tunable illumination applications, where they have a significant advantage over pc-red LEDs, with high power conversion efficiency (PCE) and narrower emission enabling higher luminous efficacy of radiation (LER). Still, adoption is limited as the complexities associated with mixing different emitters offset the value of the efficacy gain. Adoption of direct amber LEDs (~580-595nm) in illumination applications is virtually non-existent due to their lower PCE and the availability of very efficient pc-amber emitters, which suffer less from Stokes loss and LER penalties associated with the broader bandwidth than pc-red. Further improvement in PCE of direct red and amber LEDs is needed to achieve wider adoption and ultimately enable more energy savings than possible with pc-LEDs. In this project, Lumileds has developed improved high-power amber and red LEDs incorporating tensile-strain barriers into the active region to improve carrier confinement and thereby increase external quantum efficiency (EQE). This approach is most beneficial for the short (amber) end of the AlInGaP wavelength range where carrier confinement is lowest. An EQE of 22% was achieved for amber LEDs, exceeding the project target of 20%

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Feedback between radiation and transport in photovoltaics

By building on the generalized Hovel model, this work develops an analytical solution to unify photon recycling, light trapping, and carrier transport in solar cells. Enhanced transport due to photon recycling diffusion is considered. While photon recycling diffusion is often negligible, it can significantly support transport in cases where charge diffusion is low but radiative efficiency is high. Next, the diffusion equation is solved to determine carrier collection for planar and textured cells. Results elucidate novel features in the external quantum efficiency (EQE) curve that occur for textured cells with high absorption and limited transport. Then, the effect of limited transport on the radiative recombination of solar cells is investigated in detail. While the traditional treatment of detailed balance uses the applied voltage to calculate a cell's radiative recombination, the present approach uses the spatially resolved quasi-Fermi-level splitting (QFLS). Further, the discrepancy between the models is shown to be inconsequential to performance for cells with low radiative recombination (Si) or with high mobilities (lowly doped GaAs). However, for cells with high radiative recombination and low mobility (highly doped GaAs, polycrystalline CdTe, and thin-film perovskites), incorporating variation in QFLS in the determination of radiative recombination can become necessary for accurate photovoltaic modeling.

14 SOLAR ENERGY↗
DOE OSTI2025

Unexpected origin of the quantum efficiency reduction in long-wavelength (In,Ga)⁢N light-emitting diodes

Differential carrier lifetime (DCL) measurements were performed on c-plane In 𝑥 ⁢Ga 1−𝑥⁢ N/Ga⁢N single-quantum-well (QW) light-emitting diodes (LEDs) with varying indium-content QWs (x = 13.5%, 16%, 22%), emitting with violet, blue, and green wavelengths. The recombination lifetimes of LEDs were found to increase with increasing indium composition, resulting in increased carrier densities n measured by DCL. Extraction of the A coefficients, which are assumed to not vary with n, and of the effective B(n) and C(n) coefficients of the ABC model of the internal quantum efficiency (IQE) of QWs showed no significant changes in the A coefficient with increasing indium content [In] in the In 𝑥 ⁢Ga 1−𝑥 ⁢N QW, and a reduction in the B(n) and C(n) coefficients with increasing [In]. When looking at the Shockley-Read-Hall (SRH) recombination rate An, the radiative recombination rate B(n)𝑛 2 , and the Auger-Meitner (AM) recombination rate C(n)𝑛 3 , we observed that at any given n, the SRH rate is the same for the three [In] measured, while the radiative rate decreases (by up to approximately 9 times) and the AM rate decreases (by up to approximately 7 times) with increasing indium content. This shows that the larger reduction in radiative recombination rates relative to nonradiative recombination rates with increasing [In] is the largest contributor to the decreased quantum efficiencies of LEDs (the “green gap”) at any given n. While some of the reduction in the effective recombination coefficients B(n) and C(n) can be explained by the reduced wave-function overlaps of the QW with increasing indium content, the larger reduction of B(n) relative to C(n) motivates further study of the intrinsic recombination coefficients 𝐵 0 and 𝐶 0 of bulk In 𝑥 ⁢Ga 1−𝑥 ⁢N alloys and how they are related to the effective recombination coefficients B(n) and C(n) in QWs. The relative contributions of nonradiative recombination are enhanced at any given current density due to the sublinear relationship between the carrier density n and the current density. Thus, the solution to the green gap, up to any intrinsic limitations set by the indium content of the QW, from an IQE perspective, requires the design of long-wavelength (In,Ga)⁢N LEDs with improved wave-function overlaps that can operate with a lower carrier density at any given current density.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

An all optical approach for comprehensive in-operando analysis of radiative and nonradiative recombination processes in GaAs double heterostructures

We demonstrate an all optical approach that can surprisingly offer the possibility of yielding much more information than one would expect, pertinent to the carrier recombination dynamics via both radiative and nonradiative processes when only one dominant deep defect level is present in a semiconductor material. By applying a band-defect state coupling model that explicitly treats the inter-band radiative recombination and Shockley–Read–Hall (SRH) recombination via the deep defect states on an equal footing for any defect center occupation fraction, and analyzing photoluminescence (PL) as a function of excitation density over a wide range of the excitation density (e.g., 5–6 orders in magnitude), in conjunction with Raman measurements of the LO-phonon plasmon (LOPP) coupled mode, nearly all of the key parameters relevant to the recombination processes can be obtained. They include internal quantum efficiency (IQE), minority and majority carrier density, inter-band radiative recombination rate (W r ), minority carrier nonradiative recombination rate (W nr ), defect center occupation fraction (f), defect center density (N t ), and minority and majority carrier capture cross-sections (σ t and σ tM ). While some of this information is thought to be obtainable optically, such as IQE and the W r /W nr ratio, most of the other parameters are generally considered to be attainable only through electrical techniques, such as current-voltage (I-V) characteristics and deep level transient spectroscopy (DLTS). Following a procedure developed herein, this approach has been successfully applied to three GaAs double-heterostructures that exhibit two distinctly different nonradiative recombination characteristics. The method greatly enhances the usefulness of the simple PL technique to an unprecedented level, facilitating comprehensive material and device characterization without the need for any device processing.

14 SOLAR ENERGY↗
DOE OSTI2025

Optimizing energy yield of monolithic perovskite/silicon tandem solar cells in real-world Conditions: The impact of luminescent coupling

Efficient light management is key to maximizing power conversion efficiency (PCE) in monolithic perovskite/silicon tandem solar cells. Achieving peak efficiency requires closely matched current generation in all junctions, especially in integrated configurations. However, real-world conditions vary significantly due to factors such as sunlight spectrum, diffuse-to-direct sunlight ratio, angular distribution of light, subcell temperature coefficients, and ground reflection. This study introduces a comprehensive optical and device simulation to optimize perovskite/silicon tandem cells, considering experimental luminescent coupling (LC) efficiency and its dependence on working conditions, alongside variations in radiative recombination, effect of temperature on absorptivity spectra, and cloud cover. Our results show potential energy yield improvements of up to 1.4 % with LC, based on current perovskite radiative recombination records, and up to 4 % with direct bandgap materials. Although radiative recombination's dependence on excitation intensity reduces output power and requires thicker absorbers, LC compensates for these losses. LC also lowers the optimized bandgap for the perovskite top cell from 1.72 eV to 1.64–1.68 eV, or even lower in regions with redshifted irradiance. Additionally, optimization revealed that thinner silicon bottom cells require a higher perovskite top cell bandgap, impacting the balance between fabrication cost and cell stability.

14 SOLAR ENERGY↗
DOE OSTI2020

Maximizing the external radiative efficiency of hybrid perovskite solar cells

Despite rapid advancements in power conversion efficiency in the last decade, perovskite solar cells still perform below their thermodynamic efficiency limits. Non-radiative recombination, in particular, has limited the external radiative efficiency and open circuit voltage in the highest performing devices. We review the historical progress in enhancing perovskite external radiative efficiency and determine key strategies for reaching high optoelectronic quality. Specifically, we focus on non-radiative recombination within the perovskite layer and highlight novel approaches to reduce energy losses at interfaces and through parasitic absorption. By strategically targeting defects, it is likely that the next set of record-performing devices with ultra-low voltage losses will be achieved.

14 SOLAR ENERGY↗