Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Proton irradiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Characterization of the microstructure of yttrium hydride under proton irradiation

High moderation per unit volume solid moderator materials like yttrium hydride (YH x ) are necessary for compact nuclear microreactors. However, the phase stability and hydrogen transport processes of YH x under high-temperature irradiation are largely unknown. Proton irradiation was conducted on YH x at 300 °C and 580 °C to 0.2 dpa using 1 MeV or 2 MeV protons in a high-vacuum environment. The hydrogen concentration was determined before and after irradiation using elastic recoil detection analysis, and microstructural evolution was examined via post-irradiation scanning transmission electron microscopy and Raman spectroscopy. Dislocation loops and cavities were observed in all conditions; their distribution was correlated with the bombarding proton energy and ion irradiation temperature. This work revealed that hydrogen retention is proportional to the formation of traps for hydrogen gas atoms and identified pathways for hydrogen release. The relative contributions of bulk or fast diffusion paths, such as grain boundaries, delamination boundaries, and stacking faults are discussed; the primary mechanisms of hydrogen loss are likely based on diffusion, ruling out artefacts of the experimental design. In conclusion, the study suggests proton irradiation may be a strong surrogate to study hydrogen transport in hydride moderator materials under irradiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Abnormal grain growth driven by high-temperature proton irradiation in nanocrystalline Ni

In this research we examine a nanocrystalline Ni thin film exposed to high-temperature proton irradiation and compare it with as-deposited and annealed-only counterparts. Despite lacking thermal spikes typical of heavy ions, 400 °C proton irradiation drives pronounced grain growth in select grains, whereas annealing alone yields only modest coarsening. Grain-boundary statistics show fewer low-angle boundaries (10–20°) and more high-angle boundaries (55–60°), consistent with irradiation-enhanced mobility of high-misorientation boundaries. The irradiated films retain a random texture, with no evidence of texture development or sharpening. Mechanisms, such as radiation-enhanced grain boundary diffusion, beam-induced heating, and ion channeling-mediated selective grain growth, are unlikely to be the predominant drivers to explain the resultant microstructure. Instead, we suggest irradiation-induced modifications of grain-boundary structure, including possible complexion transitions, as one plausible explanation for this selective grain growth and retention of random texture. However, additional temperature–dose studies are required to confirm the mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Defect formation and microstructure tuning via proton irradiation to control electrochemical and phase reversibility in layered battery materials

The reversibility of phase transformation influences the functionality of electrode materials in batteries. In many battery materials, nanosized grains favor phase reversibility but at the cost of cyclability due to aggravated side reactions with the electrolyte. Here, in this study, we present a novel approach to enhance the phase transformation reversibility of layered oxide cathodes, exemplified by Na 2/3 Fe 1/2 Mn 1/2 O 2 through proton irradiation. In addition to forming defects, proton irradiation at sufficiently high doses can subdivide single grains into multiple nanodomains without physically rupturing them. Hence, the single grains of the material assume a pseudo-secondary particle nature without reducing the overall grain size. Preserving the grain size is advantageous, as it reduces side reactions, which is not possible with conventional grain size reduction methods. While chemical transformations and defect formation induced through proton irradiation can influence the stability of battery materials, it is expected that structural reorganization due to cycling-induced phase transformation will be contained within these nanodomains. Such confinement of phase transformation is potentially responsible for enhancing the reversibility of layered oxide materials in our study. Thus, our study suggests that grain subdivision could become an effective microstructure tuning strategy for managing electrochemical cycling-induced phase changes in battery electrodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Characterizing hole trap production due to proton irradiation in germanium cross-strip detectors

We present an investigation into the effects of high-energy proton damage on charge trapping in germanium cross-strip detectors with the goal of accomplishing three important measurements. First, we calibrated and characterized the spectral resolution of a spare COSI-balloon detector in order to determine the effects of intrinsic trapping, finding that electron trapping due to impurities dominates over hole trapping in the undamaged detector. Second, we performed two rounds of proton irradiation of the detector in order to quantify, for the first time, the rate at which charge traps are produced by proton irradiation. We find that the product of the hole trap density and cross-sectional area, [nσ] h , follows a linear relationship with the proton fluence, F p , with a slope of (5.4 ± 0.4) x 10 -11 cm/p + . Third, by utilizing our measurements of physical trapping parameters, we performed calibrations which corrected for the effects of trapping and mitigated degradation to the spectral resolution of the detector.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Synergistic Effects of Molten Salt Corrosion and Proton Irradiation on Grain Boundary Strength in Ni-20Cr

Nickel-based alloys are leading contenders for use as structural materials in molten salt reactors. While there have been extensive studies on the impact of fluoride/chloride-based molten salt corrosion on the microstructural evolution of various nickel-based alloys, the effects of simultaneous molten salt corrosion and radiation on the mechanical integrity of grain boundaries (GBs) remain underexplored. In this study, we use a Ni-20Cr model alloy to investigate this issue, subjecting it to simultaneous molten fluoride salt corrosion and proton irradiation. We performed cross-sectional and chemically-sensitive electron microscopy characterization of the microstructures of these materials, identifying the characteristic corrosion-induced microstructure and local chemical heterogeneity near GBs. After developing a sample preparation method for reliable characterization of GB strength, we assess the mechanical degradation of GBs using in situ push-to-pull micro tensile tests. Our findings reveal that voids induced by corrosion are the primary influence on the failure mode of GBs, regardless of whether proton irradiation is present. For materials that exhibit ductile fracture, those subjected to simultaneous corrosion and radiation exhibit lower yield strengths than those exposed to corrosion alone, which may be linked to the previously observed phenomenon of proton irradiation-decelerated intergranular corrosion in molten salt.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Comparison of time-resolved photoluminescence and deep-level transient spectroscopy defect evaluations in an InAs nBn detector subjected to in situ and ex situ 63 MeV proton irradiation

Deep-level transient spectroscopy and temperature-dependent time-resolved photoluminescence experiments are performed on identical InAs nBn photodetector structures as a function of in situ and ex situ 63 MeV proton irradiation to assess their generation and recombination dynamics. Pre-irradiation, the n-type InAs absorbing region, exhibits a steadily increasing minority carrier lifetime with increasing temperature, providing evidence that excited minority carriers may be recombining via shallow defect levels. From deep-level transient spectroscopy, two features are found between 10 and 275 K: a low temperature broad “shoulder,” which suggests emission from multiple shallow electron defect levels with energies <29 meV and a high temperature minimum occurring at ∼230 K with an activation energy of 539 meV, which suggests a defect in the barrier layer in the device. Two similar nBn detectors are then subjected to 63 MeV proton irradiation in step doses and measured between steps. One experiment is performed in situ with an nBn held at ∼10 K during dosing, and the other experiment is performed ex situ with a similar nBn held at room temperature for dosing. The ex situ dosing results in an evaluation of the defect introduction rate that is three to four times lower than in situ due to partial annealing of the proton-induced displacement damage at room temperature. The results of these two experiments are then compared with the dose-dependent recombination rate analysis, resulting in an estimated recombination defect cross section of 1.6 × 10 −13 cm 2 for the shallow shoulder defect.

Carrasco, Rigo A. [Air Force Research Laboratory (↗
DOE OSTI2025

Anisotropic growth of Ni 2 (Cr,Mo) ordered phase in proton irradiated Ni-Cr-Mo alloys

Ni-Cr-Mo alloys are widely used in the nuclear industry as structural materials due to their high temperature strength and corrosion resistance. Ni-based alloys containing around 33 at.% (Cr+Mo) developed a long-range ordered Ni 2 (Cr,Mo) phase after thermal aging and/or irradiation. The ordering mechanism for thermally-aged Ni 2 (Cr,Mo) phase is well-understood, characterized to be sluggish, homogeneous, and isotropic. The ordering mechanism for irradiation-induced Ni 2 (Cr,Mo) phase is not fully understood, characterized as having rapid formation and demonstrating anisotropic precipitation. Here, this work elucidates the anisotropic precipitation and anisotropic precipitation mechanism of Ni 2 (Cr,Mo) after proton irradiation in Ni-Cr-Mo alloys. Selected area electron diffraction and bright-field scanning transmission electron microscopy imaging are used to image superlattice reflections from the ordered phase and irradiation-induced defects, respectively. A higher degree of anisotropic precipitation is observed with increasing dislocation loop and void size; a phenomenon not observed in thermally aged samples.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Charge Trap Layer Supercharging for Improved Bit Reliability in 3-D NAND Flash Under Proton Irradiation

Single-event upset (SEU) cross sections are reduced in 176-layer charge trap (CT) 3-D nand devices under proton irradiation when multiple write operations are applied sequentially without the typical erase-before-write. Here, this effect is observed for multiple data patterns and in both single-level cell (SLC) and triple-level cell (TLC) operating modes. SEU cross section calculation methodologies are discussed for highly scaled 3-D devices both with and without the application of rewrites, and potential implications for long-term endurance effects are proposed.

Breeding, Matthew Luel [Sandia National Laboratori↗
DOE OSTI2026

Resilience of High-Efficiency CdSeTe:As and CdSeTe:Cu Solar Cells to Proton Irradiation

Power generation in space is currently dominated by expensive III-V multi-junction photovoltaic (PV) devices and cheap crystalline silicon (c-Si) PV devices. Both of these technologies degrade rapidly in proton-radiation-rich space environments, such as the Van Allen belt. The present study of cadmium selenide telluride- (CdSeTe-) based PV devices exposed to 150-to-1500 keV proton irradiation with fluences up to 9 x 1013 cm-2 reveal a more radiation-hard alternative to III-V and c-Si PV technologies. We report on measurement and analysis of current density vs voltage (JV), external quantum efficiency (EQE), external radiative efficiency, and capacitance vs voltage (CV) characteristics. JV characteristics of As-doped CdSeTe devices show 80% remaining power conversion efficiency (PCE) relative to unexposed controls when exposed to 650 keV protons at a fluence of 1012 cm-2. Under these same irradiation conditions, Cu-doped CdSeTe devices demonstrate an even better 95% PCE retention compared with unirradiated control devices. Evidence of radiation-induced absorber p-type doping compensation is observed in the glass-side EQE at 0 V and CV characteristics of most of the irradiated CdSeTe:As devices, but clear compensation is evident only for the most heavily irradiated CdSeTe:Cu devices. Elevated blue-green photocurrent in the film-side 0 V EQE suggests a buried junction in the most heavily irradiated CdSeTe:As devices. Although CdSeTe:Cu devices are the more resilient of the CdSeTe structures, both CdSeTe-based technologies are radiation-hard when compared to c-Si and III-V multi-junction PV.

14 SOLAR ENERGY↗
DOE OSTI2025

Separation of terbium from proton-irradiated gadolinium oxide targets – development of an effective, scalable and automatable process

This work reports an effective and scalable radiochemical separation process for isolating terbium from Gd 2 O 3 . The separation process uses three commercially available extraction chromatography resin columns, has been implemented on a computer-controlled chemistry module, and tested with 100 mg quantities of proton-irradiated nat Gd 2 O 3 . Here, the 4-hour separation procedure isolated radioterbium in 1.3 mL of 0.01 M HCl with 80 ±8% radiochemical yield and a Gd decontamination factor >(1.2 ± 0.3)·10 5 .

Adjacent lanthanide separation↗
DOE OSTI2025

Impact of proton irradiation on 4H-SiC Low Gain Avalanche Detectors (LGADs)

Silicon carbide (SiC) particle detectors have the potential to provide time resolutions and robust performance in extreme environments which exceed that of silicon detectors. In this work 4H-SiC low gain avalanche detectors (LGADs) and complementary PiN diodes were irradiated with 2.5 GeV protons at fluences up to 3.33 × 10 14 p/cm 2 . The electrostatic performance of both irradiated and non-irradiated devices was evaluated using I-V and C-V measurements. Moreover, charge collection measurements using α particles were also conducted. SiC LGADs displayed a loss in rectification, high ON-state resistances >10 10 Ω-cm 2 , and the complete removal of gain when exposed to the highest proton fluence. Additionally, the reductions in capacitance and OFF-state current pointed to compensation of the gain layer as a gain reducing mechanism. The introduction of radiation-induced defects also hinders carrier acceleration, which reduces impact ionization and further gain reduction. LGADs exposed to a fluence of 1 × 10 14 p/cm 2 experienced a partial recovery in gain (originally having a value of ∼ 2) with a value of ∼ 1.65 when applying a bias of 500 V. Charge trapping was also seen in the reduction of charge collection efficiency (CCE) to ∼ 65% for the PiN diode. However, despite the reduction in device performance, the demonstration of a measurable signal after irradiation points to the potential of SiC LGAD detectors for future high energy physics applications.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Cyclotron production of a 204 Bi/ 204m Pb generator by 24 MeV proton irradiation of natural Pb foil targets

This work focuses on the formation of a generator of 204 Bi/ 204m Pb for future applications in perturbed angular correlation spectroscopy and biological radiotracing with lead and bismuth isotopes. Generators were formed from the irradiation of natural Pb targets with 24 MeV protons producing 203,204,205,206,207 Bi that were rapidly dissolved in 3 M HNO 3 and 30 % H 2 O 2 and exchanged into a 0.1 M HCl matrix. Use of 100 mg anion exchange resin (AG 1-x8) allowed 203,204m Pb to be eluted in 600 μL of 0.1 M HCl. Furthermore, the longer-lived 205,206 Bi were eluted in 5 mL or 3 mL of either 0.25 M sodium acetate buffer pH 4.4 or 1.0 M H 2 SO 4 . Initial radiolabeling was conducted with eluted 206 Bi using DTPA and DOTA and 203 Pb using TCMC-Azide.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2025

Performance of neutron and proton irradiated AC-LGAD sensors

Characterization of strip and pixel AC-LGAD devices with both laser TCT and probe station (IV/CV) will be shown on AC-LGADs irradiated with 1 MeV reactor neutrons at JSI/Ljubljana and with 400 MeV protons at FNAL ITA to fluences from 1e13~$n_{eq}/cm^2$ to a few times 1e15~$n_{eq}/cm^2$. This study was conducted within the scope of the ePIC detector time of flight (TOF) layer R&D program at the EIC, which will feature AC-LGADs with strip and pixel geometry. Sensors in the TOF layer will receive up to 1e13 $n_{eq}/cm^2$ fluence over the lifetime of the experiment.

AC-LGAD strips↗
DOE OSTI2026

Dielectric properties of neutron and proton irradiated polymeric nanocomposite insulation for superconducting magnets of fusion power plants

Studies on radiation-resistant electrical insulation for superconducting magnets of nuclear fusion power plants are discussed. Metal oxide nanoparticle-incorporated organic polymer composite (MONAP) insulation films were manufactured and studied for their dielectric breakdown strength after exposure to neutrons and proton radiation at varying levels. Samples with up to 5 wt% of nanoparticles (NPs) of SiO 2 , MgO, and ZrO 2 were studied. The samples were exposed to radiation of up to 2 × 10 16 neutrons/cm 2 and 200 Mrad of protons. The addition of the nanoparticles improved the radiation resistance of the MONAP, and the performance depended on the type of NPs and the radiation exposure. Dielectric breakdown measurements at 77 K showed little degradation. Enhancement of dielectric strength was observed in some instances.

36 MATERIALS SCIENCE↗