Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Process Scaling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

The full-scale process and design changes for elimination of insulation edge separations and voids in tang flap area

Qualification of the full-scale process and design changes for elimination of redesigned solid rocket motor tang nitrile butadiene rubber insulation edge separations and voids was performed from 24 March to 3 December 1990. The objectives of this test were: to qualify design and process changes on flight hardware using a tie ply between the redesigned solid rocket motor steel case and the nitrile butadiene rubber insulation over the tang capture features; to qualify the use of methyl ethyl ketone in the tang flap region to reduce voids; and to determine if holes in the separator film reduce voids in the tang flap region. The tie ply is intended to aid insulation flow during the insulation cure process, and thus reduce or eliminate edge unbonds. Methyl ethyl ketone is intended to reduce voids in the tang flap area by providing better tacking characteristics. The perforated film was intended to provide possible vertical breathe paths to reduce voids in the tang area. Tang tie ply testing consisted of 270 deg of the tang circumference using a new layup method and 90 deg of the tang circumference using the current layup methods. Tie ply process success was defined as a reduction of insulation unbonds. Lack of any insulation edge unbonds on the tang area where the new process was used, and the presence of 17 unbonds with the current process, proves the test to be a success. Successful completion of this test has qualified the new processes.

Danforth, Richard A.↗
NASA NTRS1976

Response of deep and shallow tropical maritime cumuli to large-scale processes

The bulk diagnostic method of Yanai et al. (1973) and a simplified version of the spectral diagnostic method of Nitta (1975) are used for a more quantitative evaluation of the response of various types of cumuliform clouds to large-scale processes, using the same data set in the Marshall Islands area for a 100-day period in 1956. The dependence of the cloud mass flux distribution on radiative cooling, large-scale vertical motion, and evaporation from the sea is examined. It is shown that typical radiative cooling rates in the tropics tend to produce a bimodal distribution of mass spectrum exhibiting deep and shallow clouds. The bimodal distribution is further enhanced when the large-scale vertical motion is upward, and a nearly unimodal distribution of shallow clouds prevails when the relative cooling is compensated by the heating due to the large-scale subsidence. Both deep and shallow clouds are modulated by large-scale disturbances. The primary role of surface evaporation is to maintain the moisture flux at the cloud base.

Yanai, M.↗
NASA NTRS1998

Large-Scale Processing of Carbon Nanotubes

Scale-up difficulties and high energy costs are two of the more important factors that limit the availability of various types of nanotube carbon. While several approaches are known for producing nanotube carbon, the high-powered reactors typically produce nanotubes at rates measured in only grams per hour and operate at temperatures in excess of 1000 C. These scale-up and energy challenges must be overcome before nanotube carbon can become practical for high-consumption structural and mechanical applications. This presentation examines the issues associated with using various nanotube production methods at larger scales, and discusses research being performed at NASA Ames Research Center on carbon nanotube reactor technology.

Finn, John↗
NASA NTRS1998

Large-Scale Processing of Carbon Nanotubes

Scale-up difficulties and high energy costs are two of the more important factors that limit the availability of various types of nanotube carbon. While several approaches are known for producing nanotube carbon, the high-powered reactors typically produce nanotubes at rates measured in only grams per hour and operate at temperatures in excess of 1000 C. These scale-up and energy challenges must be overcome before nanotube carbon can become practical for high-consumption structural and mechanical applications. This presentation examines the issues associated with using various nanotube production methods at larger scales, and discusses research being performed at NASA Ames Research Center on carbon nanotube reactor technology.

Finn, John↗
NASA NTRS1989

A study of the effect of synoptic scale processes in GCM modelling

Research was conducted to help modeling groups at NASA to develop better weather forecasting and general circulation models (GCM) for activities relating to the meteorological uses of satellite data. The focus was on the physical processes that were being simulated by models: radiative effects and latent heat release associated with clouds; orographic influences; and heat transfer at the ocean and ice surfaces. An attempt was made to deduce the role of diabatic heating in North Atlantic cyclogenesis and in the global heat budget. Inferences were made in four studies: heat budget statistics from GCM assimilations; dynamics of north Atlantic cyclones; Cage-type energy budget calculations; and grid scale cloud formation. Mechanisms that were responsible for the variability and structure of the atmospheric on a hemispheric scale were studied by a hybrid of statistical analysis and theoretical modeling. Variability and structure are both related to synoptic scale processes through baroclinic and barotropic energy transformations.

Herman, Gerald F.↗
NASA NTRS1994

Large-scale processes in the solar nebula

Theoretical models of the structure of a minimum mass solar nebula should be able to provide the physical context to help evaluate the efficacy of any mechanism proposed for the formation of chondrules or Ca, Al-rich inclusions (CAI's). These models generally attempt to use the equations of radiative hydrodynamics to calculate the large-scale structure of the solar nebula throughout the planet-forming region. In addition, it has been suggested that chondrules and CAI's (=Ch&CAI's) may have been formed as a direct result of large-scale nebula processing such as passage of material through high-temperature regions associated with the global structure of the nebula. In this report we assess the status of global models of solar nebula structure and of various related mechanisms that have been suggested for Ch and CAI formation.

Boss, A. P.↗
NASA NTRS1989

Gray-Scale Processing For Tracking Of Welds

Digital analysis of video-image-processing system contributes to automation of weld-seam tracking. Makes no contact with seam. Small television camera views seam just ahead of point currently being welded. Arc provides illumination. Periodically frame grabber digitizes video image and stores in computer memory as gray-scale values. Seam located by analyzing Hough-transform arrays of derivatives of digitally-filtered image data. Information on location and orientation of seam used as feedback by welding robot to correct deviations of electrode from seam as welding continues.

Gutow, David A.↗
NASA NTRS1972

Data processing 2: Advancements in large scale data processing systems for remote sensing

The development of large scale data processing systems for remote sensing is studied by evaluating: (1) the suitability of several sensor types with regard to producing data required for multispectral machine analysis; (2) various types of data preprocessing necessary to prepare such data for analysis; and (3) transfer of machine processing techniques for earth resources data to user community.

Landgrebe, D. A.↗
NASA NTRS1976

Spectral and spatial energetics of the GISS model atmosphere

A calculation of the spectral and spatial energetics of the Goddard Institute for Space Studies (GISS) 9-level model of the global atmosphere is given. Results are presented from a model simulation of January 1973 and compared with previous model studies and an observational analysis for the Northern Hemisphere. The spectral analysis permits detailed study of those physical processes of scale larger than the grid spacing and allows indirect conclusions concerning unresolved subgrid-scale processes. Major conclusions for larger-than-grid-scale processes are that (1) the GISS model with a relatively coarse resolution of 4 deg latitude by 5 deg longitude produces significant nonlinear energy transfers; and (2) baroclinic conversion is large near planetary wave-number 6, but both the GISS model and another orographic model show a less peaked structure than nonorographic models and observations. A linear fit to the kinetic energy spectrum yields a power law of -2.6 in the wavenumber region 8 to 15. For subgrid-scale processes, the turbulence theory result of very small energy flux cascade is obtained.

Tenenbaum, J.↗
NASA NTRS1981

Contributions to a thermodynamic model of Earth systems on rivers

A model for the chemical (ground water) erosion and physical (bed load, including sedimentation) erosion of the land was developed. The rudiments of the relation between a regulated sea level (for the past 2500 million years) and the episodic rise and erosion of continents was examined to obtain some notion of the process scalings. Major process scales of about 200 years, 100,000 years, 3 My, 40 My, 300 My were estimated. It was suggested that a program targeted at ecological management would have to become familiar with processes at the first four scales (i.e., from glaciation to the horizontal movement of continents). The study returns to the initial premise. In order to understand and manage Earth biology (life, and modern man), it is necessary minimally to pursue systems' biogeology at a considerable number of process space and time scales via their irreversible thermodynamic couplings.

Iberall, A. S.↗
NASA NTRS1975

Feasibility and process scale-up low cost alumina fibers for advanced Re-usable Surface Insulation (RSI)

The objective of this program was to establish feasibility of a process to produce low cost aluminum oxide fibers having sufficient strength, flexibility, and thermal stability for multiple re-use at temperatures to 1480 C in advanced RSI type heat shields for reentry vehicles. Using bench-scale processing apparatus, the Alcoa 'Saphiber' process was successfully modified to produce nominally 8 microns diameter polycrystalline alpha-alumina fiber. Thermal stability was demonstrated in vacuum reheating tests to 1371 C and in atmospheric reheating to 1483 C. Individual fiber properties of strength, modulus, and flexibility were not determined because of friability and short length of the fiber. Rigidized tile produced from fiber of nominally 8, 20 and 40 micron diameter had thermal conductivities significantly higher than those of RSI SiO2 or mullite at relatively low temperature but became comparable above about 1000 C. Tile densities were high due to short fiber length, especially in the coarser diameter fiber. No significant effect of fiber diameter on thermal properties could be determined form the data. Mechanical properties of tiles deteriorated as fiber diameter increased.

Pearson, A.↗
NASA NTRS1993

ASRM propellant and igniter propellant development and process scale-up

A program of formulation and process development for ANB-3652 motor propellant was conducted to validate design concepts and screen critical propellant composition and process parameters. Design experiments resulted in the selection of a less active grade of ferric oxide to provide better burning rate control, the establishment of AP fluidization conditions that minimized the adverse effects of particle attrition, and the selection of a higher mix temperature to improve mechanical properties. It is shown that the propellant can be formulated with AP and aluminum powder from various producers. An extended duration pilot plant run demonstrated stable equipment operation and excellent reproducibility of propellant properties. A similar program of formulation and process optimization culminating in large batch scaleup was conducted for ANB-3672 igniter propellant. The results for both ANB-3652 and ANB 37672 confirmed that their processing characteristics are compatible with full-scale production.

Landers, L. C.↗
NASA NTRS1989

Size distribution of dust grains: A problem of self-similarity

Distribution functions describing the results of natural processes frequently show the shape of power laws, e.g., mass functions of stars and molecular clouds, velocity spectrum of turbulence, size distributions of asteroids, micrometeorites and also interstellar dust grains. It is an open question whether this behavior is a result simply coming about by the chosen mathematical representation of the observational data or reflects a deep-seated principle of nature. The authors suppose the latter being the case. Using a dust model consisting of silicate and graphite grains Mathis et al. (1977) showed that the interstellar extinction curve can be represented by taking a grain radii distribution of power law type n(a) varies as a(exp -p) with 3.3 less than or equal to p less than or equal to 3.6 (example 1) as a basis. A different approach to understanding power laws like that in example 1 becomes possible by the theory of self-similar processes (scale invariance). The beta model of turbulence (Frisch et al., 1978) leads in an elementary way to the concept of the self-similarity dimension D, a special case of Mandelbrot's (1977) fractal dimension. In the frame of this beta model, it is supposed that on each stage of a cascade the system decays to N clumps and that only the portion beta N remains active further on. An important feature of this model is that the active eddies become less and less space-filling. In the following, the authors assume that grain-grain collisions are such a scale-invarient process and that the remaining grains are the inactive (frozen) clumps of the cascade. In this way, a size distribution n(a) da varies as a(exp -(D+1))da (example 2) results. It seems to be highly probable that the power law character of the size distribution of interstellar dust grains is the result of a self-similarity process. We can, however, not exclude that the process leading to the interstellar grain size distribution is not fragmentation at all. It could be, e.g., diffusion-limited growth discussed by Sander (1986), who applied the theory of fractal geometry to the classification of non-equilibrium growth processes. He received D=2.4 for diffusion-limited aggregation in 3d-space.

Henning, TH.↗
NASA NTRS1997

Observational and Model Studies of Large-Scale Mixing Processes in the Stratosphere

The following is the final technical report for grant NAGW-3442, 'Observational and Model Studies of Large-Scale Mixing Processes in the Stratosphere'. Research efforts in the first year concentrated on transport and mixing processes in the polar vortices. Three papers on mixing in the Antarctic were published. The first was a numerical modeling study of wavebreaking and mixing and their relationship to the period of observed stratospheric waves (Bowman). The second paper presented evidence from TOMS for wavebreaking in the Antarctic (Bowman and Mangus 1993). The third paper used Lagrangian trajectory calculations from analyzed winds to show that there is very little transport into the Antarctic polar vortex prior to the vortex breakdown (Bowman). Mixing is significantly greater at lower levels. This research helped to confirm theoretical arguments for vortex isolation and data from the Antarctic field experiments that were interpreted as indicating isolation. A Ph.D. student, Steve Dahlberg, used the trajectory approach to investigate mixing and transport in the Arctic. While the Arctic vortex is much more disturbed than the Antarctic, there still appears to be relatively little transport across the vortex boundary at 450 K prior to the vortex breakdown. The primary reason for the absence of an ozone hole in the Arctic is the earlier warming and breakdown of the vortex compared to the Antarctic, not replenishment of ozone by greater transport. Two papers describing these results have appeared (Dahlberg and Bowman; Dahlberg and Bowman). Steve Dahlberg completed his Ph.D. thesis (Dahlberg and Bowman) and is now teaching in the Physics Department at Concordia College. We also prepared an analysis of the QBO in SBUV ozone data (Hollandsworth et al.). A numerical study in collaboration with Dr. Ping Chen investigated mixing by barotropic instability, which is the probable origin of the 4-day wave in the upper stratosphere (Bowman and Chen). The important result from this paper is that even in the presence of growing, unstable waves, the mixing barriers around

Bowman, Kenneth P.↗
NASA NTRS1991

NASA/MSFC FY91 Global Scale Atmospheric Processes Research Program Review

The reports presented at the annual Marshall Research Review of Earth Science and Applications are compiled. The following subject areas are covered: understanding of atmospheric processes in a variety of spatial and temporal scales; measurements of geophysical parameters; measurements on a global scale from space; the Mission to Planet Earth Program (comprised of and Earth Observation System and the scientific strategy to analyze these data); and satellite data analysis and fundamental studies of atmospheric dynamics.

Leslie, Fred W.↗
NASA NTRS2013

The HyMeX Special Observation Period in Central Italy: Precipitation Measurements, Retrieval Techniques and Preliminary Results

The Mediterranean area concentrates the major natural risks related to the water cycle, including heavy precipitation and flash-flooding during the fall season. The capability to predict such high-impact events remains weak because of the contribution of very fine-scale processes and their non-linear interactions with the larger scale processes. These societal and science issues motivate the HyMeX (Hydrological cycle in the Mediterranean Experiment, http://www.hymex.orgl) experimental programme. HyMeX aims at a better quantification and understanding of the water cycle in the Mediterranean with emphasis on intense events. The observation strategy of HyMEX is organized in a long-term (4 years) Enhanced Observation Periods (EOP) and short-term (2 months) Special Observation Periods (SOP). HyMEX has identified 3 main Mediterranean target areas: North-West (NW), Adriatic (A) and South-East (SE). Within each target area several hydrometeorological sites for heavy rainfall and flash flooding have been set up. The hydrometeorological sire in Central Italy (CI) is interested by both western and eastern fronts coming from the Atlantic Ocean and Siberia, respectively. Orographic precipitations play an important role due to the central Apennine range, which reaches nearly 3000 m (Gran Sasso peak). Moreover, convective systems commonly develop in CI during late summer and beginning of autumn, often causing localized hailstorms with cluster organized cells. Western fronts may heavily hit the Tiber basin crossing large urban areas (Rome), whereas eastern fronts can cause flash floods along the Adriatic coastline. Two major basins are involved within Cl region: Tiber basin (1000 km long) and its tributary Aniene and the Aterno-Pescara basin (300 km long). The first HyMeX SOP1.1 was carried out from Sept. till Nov. 2012 in the NW target area The Italian SOP1.1 was coordinated by the Centre of Excellence CETEMPS, University of L'Aquila, a city located in the CI heart. The CI area was covered by a uniquely dense meteorological instrumentation thanks to a synergy between Italian institutions and NASA-GSFC. The following RADARs were operated: a Doppler single-polarization C-band radar located at Mt Midia; the Polar 55C Doppler dual-polarization C-band radar located in Rome; a Doppler C-hand polarimetric radar located at Il Monte (Abnazo); a polarimetric X-band mini-radar in L' Aquila; a polarimetric X-hand portable mini-radar in Rome; a single-polarization X-band mini-radar in Rome. DISDROMETERs were also deployed: 4 Parsivel optical disdrometers in Rome (at Sapienza, CNR-ISAC and CNR-INSEAN); 1 2D-video disdrometer in Rome; 3 Parsivels optical disdrometer respectively in L'Aquila (Abnazo), Avezzano (Abruzzo) and Pescara (Abnazo). Other INSTRUMENTS were available: 1 K-band vertically-pointing micro rain-radar (MRR), 2 Pludix X-band disdrometers, 1 VLF lightning sensor, 1 microwave radiometer at 23-31 GHz in Rome (at Sapienza); the raingauge network with more than 200 stations in Central Italy. Three overpasses in CI were also performed by the Falcon 20 aircraft equipped with the 950Hz cloud radar RASTA Analysis of the SOP1.1 main events in CI will be described by focusing on the raindrop size distribution statistics and its geographical variability. Intercomparison of rainfall estimates from disdrometers, raingauges and radars will be illustrated with the aim to provide a quality-controlled and physically consistent rainfall dataset for meteorological modeling validation and assimilation purposes.

Gatlin, Patrick↗