Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure Vessel Steels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A Model to Account for the Effects of Load Ratio and Hydrogen Pressure on the Fatigue Crack Growth Behavior of Pressure Vessel Steels

A phenomenological model for estimating the effects of load ratio R and hydrogen pressure P H2 on the hydrogen-assisted fatigue crack growth rate (HA–FCGR) behavior in the transient and steady-state regimes of pressure vessel steels is described. The “transient regime” is identified with crack growth within a severely embrittled zone of intense plasticity at the crack tip. The “steady-state” behavior is associated with the crack growing into a region of comparatively lower hydrogen concentration located further away from the crack tip. The model treats the effects of R and P H2 as being functionally separable. In the transient regime, the effects of the hydrogen pressure on the HA–FCGR behavior were negligible but were significant in the steady-state regime. The hydrogen concentration in the steady-state region is modeled as being dependent on the kinetics of lattice diffusion, which is sensitive to pressure. Experimental HA–FCGR data from the literature were used to validate the model. The new model was shown to be valid over a wide range of conditions that ranged between –1 ≤ R ≤ 0.8 and 0.02 ≤ P H2 ≤ 103 MPa for pressure vessel steels.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Consistency of fatigue crack growth behavior of pipeline and low-alloy pressure vessel steels in gaseous hydrogen

Here, this study investigates the fatigue crack growth rate (FCGR) behavior of pipeline and low-alloy pressure vessel steels in high-pressure gaseous hydrogen. Despite a broad range of yield strengths and microstructures ranging from ferrite/pearlite, acicular ferrite, bainite, and martensite, the FCGR in gaseous hydrogen remained consistent (falling within a factor of 2–3). Steels with higher fractions of pearlite, typical of older vintage pipeline steels, exhibited modestly lower crack growth rates in gaseous hydrogen compared to steels with lower fractions of pearlite. Crack growth rates in these materials exhibit a systematic dependence on stress ratio and partial pressure of hydrogen, as captured in the recently published fatigue design curves in ASME B31 code case 220 for pipeline steels and ASME BPVC code case 2938 for pressure-vessel steels.

08 HYDROGEN↗
DOE OSTI2022

Machine learning predictions of irradiation embrittlement in reactor pressure vessel steels

Abstract Irradiation increases the yield stress and embrittles light water reactor (LWR) pressure vessel steels. In this study, we demonstrate some of the potential benefits and risks of using machine learning models to predict irradiation hardening extrapolated to low flux, high fluence, extended life conditions. The machine learning training data included the Irradiation Variable for lower flux irradiations up to an intermediate fluence, plus the Belgian Reactor 2 and Advanced Test Reactor 1 for very high flux irradiations, up to very high fluence. Notably, the machine learning model predictions for the high fluence, intermediate flux Advanced Test Reactor 2 irradiations are superior to extrapolations of existing hardening models. The successful extrapolations showed that machine learning models are capable of capturing key intermediate flux effects at high fluence. Similar approaches, applied to expanded databases, could be used to predict hardening in LWRs under life-extension conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An Atom Probe Tomography Study of the Through Wall Attenuation Effect on Cu-rich Precipitate Formation in a Reactor Pressure Vessel Steel

In this study, high-Cu weld material harvested from an ex service reactor pressure vessel (RPV) steel from Unit 1 of the decommissioned Zion Nuclear Generating Station has been characterized using atom probe tomography. Samples taken from 4 different positions through the thicknesses of the pressure vessel wall from the water-side to the air-side were characterized, along with an unirradiated baseline material. In the baseline material, no precipitates were found and the Cu was observed to be fully in solid solution; however, scanning transmission electron microscopy combined with energy dispersive spectroscopy (STEM-EDS) revealed the presence of ϵ -Cu that form during processing of the material and results in the concomitant decrease of matrix Cu. Following irradiation, a high number density of nano-scale Cu-rich precipitates (CRPs) were observed, uniformly distributed throughout the matrix. The Cu content within the CRPs was found to be ~30-35 at.% regardless of location in the wall. No statistically significant variation in the compositions, mean radius, number density, or volume fraction as a function of location within the wall was observed. The measured matrix Cu level excluding CRPs contribution was found to be ~90 appm higher than the solubility limit suggesting that further nucleation and growth of the CRPs under continued operations would have occurred. These results clearly demonstrate that the neutron energy attenuation has no significant effect on the precipitation kinetics of CRPs regardless of location in the wall in high-Cu RPV steels under irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A critical review of irradiation-induced changes in reactor pressure vessel steels

A large body of work has been conducted to investigate the embrittlement and degradation of reactor pressure vessel (RPV) steels. This includes experiments on alloys with different compositions, performed in research and test reactors and ion accelerators that span various temperatures, fluxes, and fluences. In this paper, we perform a critical review of the published experimental data and compile experimentally reported values for dislocation loop size/density, precipitate size/density and yield stress into an easily downloadable format that can be used by both experimentalists and modelers. This thorough experimental review is complemented by a brief review of simulation efforts at atomistic and mesoscopic length scales. Finally, this paper highlights key aspects of the behavior of RPV steels under irradiation, identifies gaps or discrepancies in current understanding, and identifies priority future research directions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Characterizing the flux effect on the irradiation embrittlement of reactor pressure vessel steels using machine learning

In-service exposure to high-energy neutrons embrittles reactor pressure vessel (RPV) steels. An increase in the yield stress (Δσ y ) results in a corresponding increase in the brittle to ductile transition temperature (ΔT c ). Most existing models underpredict ΔT c at higher fluence following accelerated irradiations in test reactors. High fluence, up to 10 20 n/cm 2 in some cases, will be reached over extended RPV vessel operation of 80 years, or more, at low service flux. Embrittlement has been extensively studied in accelerated, higher flux test reaction irradiations. However, the use of test reactor data naturally raises the question of flux effects. Here, this study used a machine learning approach trained on a set of hardening data, covering a wide range of flux, fluence, and steel compositions to determine the interactive effects of both irradiation and material variables on Δσ y . The analysis included machine learning-based cross-plots of the variable dependence of Δσ y for six core steels (i.e., CM6, LC, LD, LG, LH, and LI), with controlled differences in their Cu and Ni contents. A primary objective is to evaluate an effective to actual fluence (Φt e /Φt) ratio, as a function of flux, fluence, and steel composition. This is information critical to properly use intermediate flux-high fluence data in calibrating a low flux-high fluence embrittlement model. The predicted Φt e /Φt is reasonably consistent with estimates previously derived from a physics-based solute recombination trap model.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Influence of fabrication on microstructure and heat affected zone width in weldments of nuclear reactor pressure vessel steel

Advanced manufacturing routes such as electron beam welding and powder metallurgy with hot isostatic pressing are increasingly used across energy and aerospace industries, where the reliable prediction of weld behavior and heat affected zone (HAZ) evolution is critical. This study examines how fabrication routes and post-weld heat treatments influence phase distribution, crystallite size, microstrain, and dislocation density in nuclear reactor pressure vessel steels using synchrotron X-ray diffraction (SXRD). Retained austenite occurs only in samples that did not undergo austenitization, whereas an austenitizing heat treatment fully eliminates retained austenite and produces a more uniform microstructure across the weldment in terms of phase fraction, dislocation density, and microstrain. The Rosenthal solution underestimates the HAZ width for powder metallurgy samples. A newly proposed modified Rosenthal solution, reducing density by accounting for porosity, matches the SXRD-measured HAZ width with a 0.65% error. Structure–property correlations reveal that dislocation density correlates strongly with nanohardness in homogenous microstructures, while in heterogenous weldments nanohardness is further influenced by the presence of dissimilar phase boundaries. These findings provide new insight into the thermal and microstructural response of powder metallurgy fabricated steels and offer a framework for optimizing welding procedures and heat treatments in advanced manufacturing applications.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Cluster dynamics modeling of Mn-Ni-Si precipitates coupled with radiation-induced segregation in low-Cu reactor pressure vessel steels

Formation of precipitates enhanced or induced by irradiation causes hardening and embrittlement of nuclear structural materials. Post-irradiation microstructure characterization of reactor pressure vessel (RPV) steels has shown that precipitation can be strongly associated with radiation-induced segregation (RIS) of solutes on dislocations. However, RIS and precipitation have not been coupled in previous precipitation modeling of RPV steels. Here in this study, a new hybrid and spatially-dependent precipitation model is developed that couples cluster dynamics with RIS, providing an unique way to account for concurrent evolution of heterogeneous cluster densities as well as solute and point defect concentration profiles. The model is applied to study the segregation of Mn, Ni, and Si on dislocations and heterogeneous nucleation of Mn-Ni-Si rich precipitates (MNSPs) in a low-Cu RPV steel. The result shows that the onset of MNSP nucleation on dislocations occurs at the fluence of 2 x 10 23 n.m -2 . The number density and mean radius can reach ~ 10 24 m -3 and 1-2 nm at high fluence, respectively. These observations suggest that the role of RIS and heterogeneous nucleation can be significant for RPV steels under a high fluence of irradiation. Results of simulations adopting various dose rates and dislocation densities show an increased fraction of MNSPs on dislocations at the condition of low dose rate, high dislocation density, and high fluence.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Acoustic emission testing of 12-nickel maraging steel pressure vessels

Acoustic emission data were obtained from three point bend fracture toughness specimens of 12-nickel maraging steel, and two pressure vessels of the same material. One of the pressure vessels contained a prefabricated flaw which was extended and sharpened by fatigue cycling. It is shown that the flawed vessel had similar characteristics to the fracture specimens, thereby allowing estimates to be made of its nearness to failure during a proof test. Both the flawed and unflawed pressure vessel survived the proof pressure and 5 cycles to the working pressure, but it was apparent from the acoustic emission response during the proof cycle and the 5 cycles to the working pressure that the flawed vessel was very near failure. The flawed vessel did not survive a second cycle to the proof pressure before failure due to flaw extension through the wall (causing a leak).

Dunegan, H. L.↗
NASA NTRS1975

An investigation of fracture toughness, fatigue-crack growth, sustained-load flaw growth, and impact properties of three pressure vessel steels

The elastic fracture toughness of the three steels is shown to not decrease significantly with decreasing temperature from room temperature to about 244 K (-20 F.). The elastic fracture toughness of the three steels increased with increasing specimen width and thickness. The fatigue-crack-growth data for all three steels fall into relatively narrow scatter bands on plots of rate against stress-intensity range. An equation is shown to predict the upper bounds of the scatter bands reasonably well. Charpy impact energies decreased with decreasing temperature in the nominal temperature range from room temperature to 244 K (-20 F). The nil-ductility temperatures of the steels are discussed.

Hudson, C. M.↗
DOE OSTI2023

The effect of phosphorus on precipitation in irradiated reactor pressure vessel (RPV) steels

Embrittlement of light water reactor pressure vessels (RPV) steels by fast neutron irradiation may limit extended nuclear plant life. Embrittlement, which is manifested as increases in various indexes of a ductile to brittle transition temperatures (ΔT), is primarily due to hardening by nanoscale precipitates containing Cu, Ni, Mn, and Si, which form under irradiation. In addition to these elements, P has also been found to play a role in embrittlement. While only slightly enriched in the precipitates, hardening and embrittlement increase with trace P concentrations in low-Cu steels. Here, we characterize the individual and synergistic irradiation precipitation and hardening mechanisms in a series of RPV steels containing no to low-Cu and with systematic variations in Ni and P. In this study, the steels were irradiated to a fluence of ~ 1.38 x 10 20 n/cm 2 at ~ 292 °C in the UCSB ATR-2 experiment. In Cu-free medium and high-Ni RPV steels, atom probe tomography shows that P and Ni promotes precipitation of P-Mn-Si-Ni and Mn-Si-Ni precipitates, respectively. The precipitate microstructure correlates with the observed irradiation hardening.

36 MATERIALS SCIENCE↗