SEARCH · Engineering Papers

Results for “Plastic constraint”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Planar, longitudinal, compressive waves in solids: Thermodynamics and uniaxial strain restrictions

A new tri-axial pressure-based constitutive expression has been found using Cauchy's stress tensor. This stress state emphasizes pressure and shear stress. The description is a pressure plus an effective shear stress allowing for a constitutive law based on atomic solid-state phase changes in crystalline cells due to pressure plus shear-based dislocation motion commonly associated with plasticity. Pressure has a new role in the material's constitutive response as it is separated from plasticity. The thermo-mechanical system describes third-order Gibbs’ expressions without specific volume restrictions placed upon the material. Isothermally, the ratio of heat to shear work in elastic copper is shown to approach zero at a very low temperature and become larger than one as temperature approaches melting. Wave compression models investigated are elastic and plastic: in fully elastic materials, the planar wave is restricted by Poisson's effect although plastic shear changes this constraint. Plastic deformation, dominated by dissipative shear stresses in uniaxial strain, heats the material while excluding phase changes from hydrostatic pressures. The material properties per se across Hugoniot shocks are described with entropy concepts. Shock waves are exceedingly complex since the constitutive laws are linked at extreme temperatures, pressures, and shear stresses. Isothermal, isentropic, isochoric, and iso-shear conditions are used throughout with Jacobian algebra.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS2015

Crack Instability Predictions Using a Multi-Term Approach

Present crack instability analysis for fracture critical flight hardware is normally performed using a single parameter, K(sub C), fracture toughness value obtained from standard ASTM 2D geometry test specimens made from the appropriate material. These specimens do not sufficiently match the boundary conditions and the elastic‐plastic constraint characteristics of the hardware component, and also, the crack instability of most commonly used aircraft and aerospace structural materials have some amount of stable crack growth before fracture which makes the normal use of a K(sub C) single parameter toughness value highly approximate. In the past, extensive studies have been conducted to improve the single parameter (K or J controlled) approaches by introducing parameters accounting for the geometry or in‐plane constraint effects. Using 'J‐integral' and 'A' parameter as a measure of constraint is one of the most accurate elastic‐plastic crack solutions currently available. In this work the feasibility of the J‐A approach for prediction of the crack instability was investigated first by ignoring the effects of stable crack growth i.e. using a critical J and A and second by considering the effects of stable crack growth using the corrected J‐delta a using the 'A' parameter. A broad range of initial crack lengths and a wide range of specimen geometries including C(T), M(T), ESE(T), SE(T), Double Edge Crack (DEC), Three‐Hole‐Tension (THT) and NC (crack from a notch) manufactured from Al7075 were studied. Improvements in crack instability predictions were observed compared to the other methods available in the literature.

Zanganeh, Mohammad↗

NASA NTRS1974

A rheological mechanism of penetrative wear

A model is proposed which explains the penetrative wear of a soft material by a harder one. Three distinct modes of penetration are present depending on the applied load. During the most severe penetration plate-like wear debris is ejected at the leading edge of the slider. A series of slip line fields is presented to approximate this debris formation process. Plastic constraint is seen to be an important factor in wear particle formation.

Bates, T. R., Jr.↗

NASA NTRS1980

Influence of stress interaction on the behavior of off-axis unidirectional composites

The yield function for plane stress of a transversely isotropic composite lamina consisting of stiff, linearly elastic fibers and a von Mises matrix material is formulated in terms of Hill's elastic stress concentration factors and a single plastic constraint parameter. The above are subsequently evaluated on the basis of observed average lamina and constituent response for the Avco 5505 boron epoxy system. It is shown that inclusion of residual stresses in the yield function together with the incorporation of Dubey and Hillier's concept of generalized yield stress for anisotropic media in the constitutive equation correctly predicts the trends observed in experiments. The incorporation of the strong axial stress interaction necessary to predict the correct trends in the shear response is directly traced to the high residual axial stresses in the matrix induced during fabrication of the composite.

Pindera, M. J.↗

NASA NTRS1990

The potential for ductility enhancement from surface and interface dislocation sources in NiAl

Limited ductility and toughness of NiAl and related aluminides near room temperature pose major problems in their potential application as structural materials. An analysis of these problems is presented as part of a review of the flow and fracture behavior of binary NiAl. Following this discussion is a demonstration that conditions of elastic and plastic constraint associated with phase boundaries afforded by surface films, internal lamellae, or precipitates may introduce sufficient densities of mobile dislocations to enhance the ductility of NiAl-based materials by significant amounts. Examples of this behavior are presented for several model materials, including 001- and 123-oriented single crystals of oxide-coated NiAl, directionally solidified beta-gamma-prime (Ni70Al30) and beta-gamma (Ni50Fe30Al20) in situ composites, and several NiAl/precipitate systems. The nature of the resulting dislocation substructures and the effects of several materials variables are described.

Noebe, R. D.↗

DOE OSTI2021

Constraint and size effects in confined layer plasticity

Plane strain finite element analyses are used to model the experiments for a thin metal layer confined between elastic solids. Here, the thin metal layer undergoes elastic-plastic deformations, here modelled by strain gradient plasticity, while the rest of the solid deforms only elastically. Plane strain is assumed and finite strains are accounted for. The microscopic boundary condition at the band interface is initially taken to be zero plastic strain increment, but plastic straining at the interface is allowed when the plastic strain gradient at the interface has exceeded a critical value. When the narrow metal band is inclined 45° relative to the direction of compression of the solid simple shear develops in the band and predictions are rather similar to those of a one-dimensional analysis for an infinite band. For a band at 90° the elastic parts give significant constraint on plastic flow, the stress fields are non-uniform along the band and the average nominal compressive stress shows strong sensitivity to the layer thickness and to the width of the specimen. Remarkably good qualitative, and in some cases quantitative, agreement is found with the experimental observations. Considering also other band angles, both the average nominal shear and compressive stress show variations with the angle.

36 MATERIALS SCIENCE↗

NASA NTRS1993

Three-dimensional elastic-plastic finite-element analyses of constraint variations in cracked bodies

Three-dimensional elastic-plastic (small-strain) finite-element analyses were used to study the stresses, deformations, and constraint variations around a straight-through crack in finite-thickness plates for an elastic-perfectly plastic material under monotonic and cyclic loading. Middle-crack tension specimens were analyzed for thicknesses ranging from 1.25 to 20 mm with various crack lengths. Three local constraint parameters, related to the normal, tangential, and hydrostatic stresses, showed similar variations along the crack front for a given thickness and applied stress level. Numerical analyses indicated that cyclic stress history and crack growth reduced the local constraint parameters in the interior of a plate, especially at high applied stress levels. A global constraint factor alpha(sub g) was defined to simulate three-dimensional effects in two-dimensional crack analyses. The global constraint factor was calculated as an average through-the-thickness value over the crack-front plastic region. Values of alpha(sub g) were found to be nearly independent of crack length and were related to the stress-intensity factor for a given thickness.

Newman, J. C., Jr.↗

DOE OSTI2025

Approach to evaluate the effect of selected additives on the environmental impacts of plastic product manufacturing and recycling

Plastic waste management has become a topic of increasing public interest due to the growing amount of plastic waste entering landfills, being combusted, or being leaked into the environment due to mismanagement. The portion of plastic products that is currently recycled remains low (< 9 % in the U.S.). This is driven by numerous factors including infrastructure and collection needs to improve the recycling rate of plastic waste, technological constraints in recycling the wide variety of plastic products associated with the diverse range of (non-transparent) formulations, and economic limitations for recycling plastic and using recycled plastic in new plastic products (e.g., consumer incentives to recycle, economic value of recycled plastic). The relative importance of these factors is not well understood, and each requires additional research.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Recurrent neural network-based multiaxial plasticity model with regularization for physics-informed constraints

We report a recurrent neural network (RNN) based model is developed as a surrogate to predict nonlinear plastic response under multiaxial loading. The RNN-based model is trained and tested on stress versus strain curves generated using a numerical solution based on the classical radial return method. Besides simply learning the basic constitutive relationship, a novel approach is taken to enforce certain physical conditions. Specifically, regularization is employed to maintain non-negative plastic power density throughout the loading history thereby ensuring monotonically increasing plastic work and thermodynamic consistency. Enforcing physics in this manner permits coupling of the data-driven RNN approach with physics-based knowledge and laws. This has the effect of reducing the necessary amount of data and ensuring known physical laws are not violated. Since, once trained, the model need not perform the expensive task of solving nonlinear equations, its efficiency is orders of magnitude greater than its numerical counterpart. The RNN-based model has been trained on varied sets of data and the accuracy on test datasets validated. The developed model is general and robust and has widespread application such as in the simulation of metal forming, large scale plasticity, and part life prediction.

42 ENGINEERING↗

NASA NTRS1981

Optimum structural design with plate bending elements - A survey

A survey is presented of recently published papers in the field of optimum structural design of plates, largely with respect to the minimum-weight design of plates subject to such constraints as fundamental frequency maximization. It is shown that, due to the availability of powerful computers, the trend in optimum plate design is away from methods tailored to specific geometry and loads and toward methods that can be easily programmed for any kind of plate, such as finite element methods. A corresponding shift is seen in optimization from variational techniques to numerical optimization algorithms. Among the topics covered are fully stressed design and optimality criteria, mathematical programming, smooth and ribbed designs, design against plastic collapse, buckling constraints, and vibration constraints.

Haftka, R. T.↗

NASA NTRS2003

Development of a Fatigue Crack Growth Coupon for Highly Plastic Stress Conditions

The analytical approach used to develop a novel fatigue crack growth coupon for highly plastic stress field condition is presented in this paper. The flight hardware investigated is a large separation bolt that has a deep notch, which produces a large plastic zone at the notch root when highly loaded. Four test specimen configurations are analyzed in an attempt to match the elastic-plastic stress field and crack constraint conditions present in the separation bolt. Elastic-plastic finite element analysis is used to compare the stress fields and critical fracture parameters. Of the four test specimens analyzed, the modified double-edge notch tension - 3 (MDENT-3) most closely approximates the stress field, J values, and crack constraint conditions found in the flight hardware. The MDENT-3 is also most insensitive to load misalignment and/or load redistribution during crack growth.

Allen, Phillip A.↗

NASA NTRS1979

A new basis for the determination of fracture toughness

A study is presented which shows that the growth of the plastic zone and the constraint in a compact tension specimen depends significantly on specimen width. The analysis permits the estimation of the contribution of the growth of plastic zone to the deviation from linearity. The contribution of the crack growth to the deviation from linearity is evaluated from the analysis of a typical R-curve data. A combination of these two analyses enables one to define a very simple procedure for the determination of fracture toughness. The fracture toughness is defined as the stress intensity value at which the crack extension starts. The good agreement between analytical results and experimental KQ and KIC values determined over a wide range of thicknesses, widths, and materials justifies the proposed procedures. The KIC determined according to this procedure is independent of specimen width and such a procedure enhances the range of applicability of the K concept to a wider combination of configurations and materials.

Banerjee, S.↗

DOE OSTI2021

Hydrogen-enhanced compatibility constraint for intergranular failure in FCC FeNiCoCrMn high-entropy alloy

The fundamental mechanism of hydrogen embrittlement was investigated in the high-entropy alloy FeNiCoCrMn using slow strain rate tensile tests with and without internal hydrogen. Hydrogen induced intergranular failure and reduced the average grain elongation parallel to the tensile axis, but also increased the local plasticity within grains. Here, the influence of hydrogen on plasticity establishes a compatibility constraint across grain boundaries, which results in failure along the hydrogen-weakened grain boundaries. This study is the first to directly confirm the presence of the hydrogen-enhanced compatibility constraint in a high-entropy alloy and highlights the importance of developing a physical understanding of grain-scale interactions.

36 MATERIALS SCIENCE↗

NASA NTRS2018

Implementation of J-A Methodology Elastic-Plastic Crack Instability Analysis Capability into the WARP-3D Code

Characterization of the near crack-tip stress/strain fields is the foundation of fracture mechanics. The description of the near tip stress field and the prediction of when fracture occurs is well established for brittle materials that exhibit linear elastic behavior. However, in ductile materials or conditions that violate linear elastic assumptions (Aluminum alloys, Al 2024-T3, Al 2024- T351 etc.), the elastic-plastic crack-tip stress fields are characterized by the Hutchison-Rice-Rosengren (HRR) field. The J-integral is commonly used to characterize amplitude of the HRR field under elastic-plastic conditions. The J-integral has been demonstrated for crack-tip fields that are under high constraint conditions (i.e., small-scale plasticity where the J-dominance is maintained). However, as the external load increases, yielding changes from small- to largescale plasticity and usually a loss of constraint (i.e., reduction in the triaxial stress field along the crack front). The loss of constraint leads to the deviation of the crack-tip stress fields from that given by the HRR field. Hence, the J-dominance will be gradually lost and additional parameter(s) are required to quantify the crack-tip stress fields and predict fracture behavior. The assessment objectives were to: 1) implement a two-parameter (i.e., J-A) fracture criterion into an elastic-plastic three-dimensional (3D) finite element analysis (FEA), 2) validate the implementation by comparison with the A parameter from literature data, 3) conduct material characterization tests to quantify the material behavior and provide fracture data for validation of the J-A fracture criteria, and (4) perform evaluations to establish if the J-A criteria can be used to predict fracture in a ductile metallic material (e.g., aluminum alloys). The A parameter in these criteria is the second parameter in a three-term elastic-plastic asymptotic expansion of the neartip stress behavior. A series of extensive FEAs were performed using WARP3D software package to obtain solutions for the A parameter for different specimen configurations. The methodology needed for the estimation of the A parameter in the asymptotic expansion was developed and implemented using Matlab®. A user material (UMAT) routine was used to model the material stress-strain response using a Ramberg-Osgood power law with a hardening exponent (n) and a material coefficient (alpha). This UMAT routine was successfully implemented in WARP3D software and validated through comparison with the experimental data. Three configurations were extracted from published results: 1) center cracked plate (CCP), 2) single edge-cracked plate (SECP), and 3) double edge-cracked plate (DECP). These configurations and four other configurations (three-hole tension (THT)), three-point bend (3PTB), three-hole compact tension (3PCT), and compact tension (CT)) were analyzed to verify the methodology that was developed and implemented into WARP3D. Solutions of the A parameter were obtained for remote tension loading conditions that started with small-scale yielding and continued into the large-scale plasticity regime. The results indicate that the methodology developed can be used to calculate the elastic-plastic J-A parameters for test specimens with a range of crack geometries, material strain hardening behaviors, and loading conditions. The J-A parameters were implemented as fracture criteria and used to predict the test results. For comparison, other fracture criteria were used to predict the same test results. Major findings include: The A constraint parameter A varies with specimen type and applied load thus accurate determination is crucial in predicting the failure load, and the A parameter is asymptotic as the failure load is approached, making an accurate determination difficult (i.e., small differences in the A parameter can cause large variations in failure load) for materials exhibiting elastic-plastic behavior. The failure predictions from J-A methodology were more accurate than the traditionally used KC and J methods, and have comparable scatter to that observed when using the crack-tip opening angle (CTOA) method. However, the J-A methodology requires considerable effort (expertise level and labor) to implement and to evaluate the A parameter for different specimen types and materials, or to apply this methodology to part-through crack (e.g., 3D problems) structural applications.

Hamm, Kenneth R., Jr.↗

DOE OSTI2022

Post-closure Nuclear Criticality Safety Evaluations for Disposition of Criticality Control Overpacks at the Waste Isolation Pilot Plant

The Waste Isolation Pilot Plant (WIPP) is a geological repository in southern New Mexico that provides for disposal of transuranic (TRU) wastes from atomic energy defense activities. The Sandia National Laboratories (Sandia) Report, Consideration of Nuclear Criticality When Disposing of Transuranic Waste at the Waste Isolation Pilot Plant, addresses nuclear criticality safety based on the projected inventory characteristics for the initial compliance certification application of WIPP in 1996. As the inventory, waste forms, and disposal package designs change, revised or new analyses are necessary to demonstrate acceptability for these configurations within the WIPP safety basis and compliance with 10,000-year post-closure standards of the US Environmental Protection Agency (EPA). Saylor and Scaglione evaluated criticality control overpacks (CCOs) in 2017 based on conservative assumptions for post-closure repository structural conditions with resulting effects on containers and container spacing, The Saylor and Scaglione evaluation of CCOs addressed a single waste configuration that represents the Surplus Plutonium Disposition Program’s dilute and dispose waste form and composition. This initial CCO study demonstrated that 50 grams of boron carbide (B 4 C) per CCO is sufficient to ensure post-closure criticality safety based on a well-mixed waste composition, and Oak Ridge National Laboratory (ORNL) subsequently determined that this amount of B 4 C does not require constraints on moisture or plastic present as moderator. The Saylor and Scaglione analysis conservatively assumes repository room closure that eliminates all space between fissile gram equivalent (FGE) 239 Pu masses. The close-packed array was selected based on limited availability of repository salt creep modeling results at that time. In 2019, Brickner provided additional evaluations for pipe overpack containers (POCs), building on the conservative basis provided by Saylor and Scaglione. Brickner’s 2019 analysis made use of new geomechanical data for post-closure spacing that rely on advances in repository modeling as documented in the work by Reedlunn and Bean. This current CCO evaluation for generic waste materials expands on earlier work performed at ORNL and includes evaluation of CCOs across a much broader range of possible waste compositions and geometries. This evaluation is intended to provide input for the required feature, event and process (FEP) screening to determine if post-closure criticality must be included as an event in the 10,000-year regulatory evaluation. As such, the approach to modeling post-closure criticality presented in this report has been coordinated with the Sandia team responsible for FEP screening. The resulting analysis supports disposition of fissile materials in the CCO containing up to 380 FGE 239 Pu and expands conditions acceptable for disposal of fissile material in CCOs. This evaluation builds on the methodology of Saylor and Scaglione and Brickner, using the most recently available geomechanical data for CCO spacing under salt creep compaction scenarios provided by Reedlunn and Bean. The broad range of fissile material configurations analyzed in this report are intended to account for configurations that may occur during the post-closure disposal time period, and it also includes waste configurations that are not physically possible to support analysis of conditions that influence neutron fluence.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2026

Continual Learning for Production-Level Machine Learning in Particle Accelerators

Particle accelerators operate in complex environments where data distribution can change dynamically, leading to data drifts that significantly challenge Machine Learning (ML) models. These non-stationary conditions often cause ML models to deteriorate in performance, making it difficult to maintain reliable predictions in operation. The primary sources of data drifts are changes in accelerator settings and changes in equipment performance which cannot be measured directly. To bridge this gap between ML development and long-term deployment in operational settings, we identify key areas within particle accelerators where continual learning can help mitigate drift-induced performance degradation. We will provide a practical guide on selecting the appropriate method given resource constraints and desired stability plasticity trade offs. As a concrete example, we will present a real-world use case for anomaly detection to predict errant beams at the Spallation Neutron Source accelerator, where continual learning has been employed to demonstrate stable performance on drifting data streams. We will present practical challenges, lessons learned, and the results from the deployed ML model.

Rajput, Kishansingh [Thomas Jefferson National Acc↗

DOE OSTI2020

Experimental methodology and theoretical framework in describing constrained plastic flow of FCC microscale tensile specimens

Small scale mechanical testing (SSMT) allows for the quantification of the mechanical responses for microscale and nanoscale material volumes. It has significant potential in improving our fundamental understanding of plastic deformation and in providing an engineering solution for testing complex and/or critical materials. Importantly, previous studies have revealed that plastic intermittency, manifested as strain bursts, are characteristic of the plastic flow behavior at the small length scale. In this work, interfacial constraint has been utilized to suppress strain bursts in order to stabilize plasticity. A new parameter, blocked volume ratio (BVR), is introduced to quantify the degree of constraint for a microscale specimen due to an interface. Here, we showed that the plastic flow behavior in FCC Ni-based metals is highly dependent on the BVR of the specimen.

36 MATERIALS SCIENCE↗

NASA NTRS1992

Effects of constraint on crack growth under aircraft spectrum loading

The objective is to study the effects of constraint on fatigue crack growth under aircraft spectrum loading. A plasticity-induced crack-closure model that accounts for constraint variations during the transition from flat-to-slant crack growth was used to correlate crack-growth rate data under constant-amplitude loading and to calculate crack growth under simulated aircraft spectrum loading. The model was applied to several thin-sheet aluminum alloy materials. Under laboratory air conditions, the transition was shown to be related to the size of the cyclic plastic zone based on the effective stress-intensity factor range for several sheet materials and thicknesses. Results from three-dimensional, elastic-plastic, finite-element analyses of a flat, straight-through crack in a thin-sheet aluminum alloy specimen showed a constraint loss similar to that assumed in the model. Using test data and the closure model, the location of the constraint-loss regime in terms of growth rate and the value of the constraint factor at these rates were determined by trial and error. The model was then used to calculate crack growth under the TWIST spectrum. The calculated results agreed reasonably well with test data. In general, the model predicted shorter crack-growth lives than tests under the TWIST spectrum by about 40 percent. For the TWIST spectrum clipped at Level 3, the calculated lives were within about 20 percent. The results demonstrated that constraint variations, especially for thin-sheet alloys, should be accounted for to predict crack growth under typical aircraft spectra.

Newman, J. C., Jr.↗