Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle Size”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Effect of particle size and particle size distribution on physical characteristics, morphology and crystal structure of explosively compacted high-T(sub c) superconductors

A superconductor, of composition Y(Ba,K,Na)2Cu3O(x)/F(y) and a composite of composition Y(Ba,K,Na)2Cu3O(x)/F(y) + Ag, with changing K, Na and F content but a constant silver content (Ag = 10 mass%) was prepared using a single heat treatment. the resulting material was ground in a corundum lined mill, separated to particle size fractions of 0-40 micron, 0-63 micron and 63-900 micron and explosively compacted, using an explosive pressure of 10(exp 4) MPa and a subsequent heat treatment. Best results were obtained with the 63-900 micron fraction of composition Y(Ba(1.95) K(0.01)Cu3O(x)F(0),(05)/Ag: porosity less than 0.01 cu cm/g and current density 2800 A/sq cm at 77K.

Kotsis, I.↗
NASA NTRS1992

Infrared (8-14 microns) remote sensing of soil particle size

Particle size of soils plays a significant role in erosion potential and other mechanical properties. Most soils are dominated by the residual mineral quartz, which displays prominent reststrahlen bands in the 8-14 microns atmospheric window. The Earth Observing System will likely provide world-wide multispectral imagery in the 8-14 microns region via the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) instrument. The ratio of ASTER bands 10/14 can be used to estimate particle size in soils, if other ASTER bands are used to minimize the confusion factors provided by soil moisture, vegetation cover, soil organic content, and the presence of abundant minerals other than quartz. Use of band ratios minimizes the effects of poor surface temperature estimates, but maximizes the need for high signal-to-noise data.

Salisbury, John W.↗
NASA NTRS1999

Laser Light Scattering with Multiple Scattering Suppression Used to Measure Particle Sizes

Laser light scattering is the technique of choice for noninvasively sizing particles in a fluid. The members of the Advanced Technology Development (ATD) project in laser light scattering at the NASA Lewis Research Center have invented, tested, and recently enhanced a simple and elegant way to extend the concentration range of this standard laboratory particle-sizing technique by several orders of magnitude. With this technique, particles from 3 nm to 3 mm can be measured in a solution. Recently, laser light scattering evolved to successfully size particles in both clear solutions and concentrated milky-white solutions. The enhanced technique uses the property of light that causes it to form tall interference patterns at right angles to the scattering plane (perpendicular to the laser beam) when it is scattered from a narrow laser beam. Such multiple-scattered light forms a broad fuzzy halo around the focused beam, which, in turn, forms short interference patterns. By placing two fiber optics on top of each other and perpendicular to the laser beam (see the drawing), and then cross-correlating the signals they produce, only the tall interference patterns formed by singly scattered light are detected. To restate this, unless the two fiber optics see the same interference pattern, the scattered light is not incorporated into the signal. With this technique, only singly scattered light is seen (multiple-scattered light is rejected) because only singly scattered light has an interference pattern tall enough to span both of the fiber-optic pickups. This technique is simple to use, easy to align, and works at any angle. Placing a vertical slit in front of the signal collection fibers enhanced this approach. The slit serves as an optical mask, and it significantly shortens the time needed to collect good data by selectively masking out much of the unwanted light before cross-correlation is applied.

Meyer, William V.↗
NASA NTRSDate not supplied

Particle Size Distribution Parameters from SAGE III/ISS Extinction Spectra

Stratospheric aerosols play key roles in the chemistry and radiation balance of the atmosphere and are a key input parameter for global chemistry and climate models. The degree to which aerosols impact chemistry and radiation balance depends primarily on the relative abundance of different sized particles within the sample volume, often referred to as the particle size distribution (PSD). If the PSD is accurately known then other key modeling parameters (e.g., surface area density and effective radius) can be derived. Historically, occultation observations from orbital instruments such as SAGE III/ISS have been used to infer these PSD parameters by inverting the extinction coefficient spectra. However, past efforts routinely failed to account for measurement uncertainty and lacked a rigorous estimate of the inferred PSD uncertainty. We carried out a series of simulations to evaluate the accuracy of these inferences and, for every valid SAGE III/ISS extinction spectrum, determined the range of PSD parameters that fell withing the bounds of the extinction error bars. Special application of this method was applied to estimate the impact of the 2022 Hunga Tonga eruption had on particle size distributions.

Travis N Knepp↗
DOE OSTI2022

Impact of particle size and particle-flow-wall coupling on pressurized oxy-combustion in the down-fired burner

Concerns over climate change have led to numerous efforts in developing low-carbon energy technologies. Pressurized oxy-combustion (POC) is a promising candidate to reduce carbon emissions in power generation. Designing an effective burner plays a vital role in developing new coal combustion technologies. Because of the high pressure, the volume fraction of coal particles at the fuel inlet of the burner of a pressurized oxy-combustor is close or even higher than the maximum limit that commercial CFD codes (e.g., ANSYS FLUENT) can handle. At this high particle volume fraction, the interactions among particles, fluid flow, and wall need to be re-evaluated. The present computational work is the first step of a systematic analysis of the particle influence, like releasing method, releasing locating, and particle size, in a pilot-scale POC combustor, developed at Washington University in St. Louis (WUSTL). In a POC process, pulverized coal is burned under elevated pressure and O2-CO2 environment. Specifically, a 15-bar, 100 kWth, POC combustor is modeled employing ANSYS FLUENT, using Reynolds-averaged Navier-Stokes (RANS) modeling. It is revealed that for this pilot-scale, pressurized burner, velocity profiles of the near-wall region in this POC facility exhibit some discrepancy against the near-wall turbulent flow velocity profile. In order to investigate the particle influence in the near-wall region, particle releasing location will be investigated. Numerical simulation results exhibit the coupling effect of turbulence flow and particles in this case. The particle size also demonstrates a great effect on particle trajectory, then further has an impact on flame stability and temperature.

Li, Lei↗
NASA NTRS1984

The effect of particle size on the electrical conductivity of CuCl (Al2O3) composites

The conductivity of CuCl containing Al2O3 of 0.06, 0.3, 1, 3, 8, and 15 micron sized particles was measured between 25 and 390 C. Conductivity was enhanced for the 0.06 and 0.3 sized Al2O3 particles for temperatures below approximately 250 C. The maximum enhancement occurred at 10 m/o of 0.06 micron Al2O3 at 25 C. Uncertain degrees of agglomeration as well as the grain size of the matrix were found to be significant.

Chang, M. R.-W.↗
DOE OSTI2024

Effects of particle size and AQDS on the flow of electron equivalents between magnetite and aqueous Fe2+

Magnetite can occur naturally in nano- to micro-size regimes and widely coexists with aqueous Fe2+ (Fe2+ (aq)) in natural environments. However, the effects of magnetite particle size on its interaction with Fe2+ (aq) in anoxic subsurface environments, particularly with redox-active organics, remain unclear. In this study, the interactions of Fe2+ (aq) with magnetite particles of 12 nm versus 109 nm (Mag-12 vs. Mag-109), with/without anthraquinone- 2,6-disulfonate (AQDS), were studied based on equilibrium Fe2+ (aq) concentrations, kinetics of AQDS reduction, and structural versus surface-localized Fe(II)/Fe(III) ratios (xstru and xsurf) of magnetite. In the absence of AQDS, Mag-12 tends to release Fe2+ (aq) at pH 7 but sorb Fe2+ (aq) at pH 8, while Fe2+ (aq) uptake by Mag-109 is observed at both pH 7 and 8. The amounts of Fe2+ (aq) adsorbed per unit area of Mag-109 is higher than that of Mag-12, due to the higher electron-accepting capacity of Mag-109 that facilitates interfacial electron transfer (IET) from surfaceassociated Fe(II) to structural Fe(III). The increases of xstru and xsurf in Mag-109 after reaction with Fe2+ (aq) at pH 7 and 8 suggest Fe2+ (aq) incorporation or electron injection into the structure of Mag-109. The presence of AQDS promotes Fe2+ (aq) uptake by both Mag-12 and Mag-109. However, AQDS reduction by Fe2+-amended Mag-12 results in the decrease of xstru and inhibits Fe2+ (aq) incorporation or electron injection into the structure. On the contrary, the increase of xstru observed in Fe2+-amended Mag-109 after reaction with AQDS suggests that Fe2+ (aq) incorporation or electron injection into the surface structure and then consequently into the interiors is more favorable for magnetite with larger particle sizes. The different flow directions of electron equivalents across the solid-solution interfaces can be attributed to the relatively higher electron-accepting capacity, i.e. redox potential, of Mag-109 than Mag-12; larger particle sizes facilitate IET from surface-associated Fe(II) to structural Fe(III) and promotes further Fe2+ (aq) uptake, culminating in the pronounced changes of redox potentials in magnetitebearing solutions. The results demonstrate that particle size and redox-active organics are important factors to affect reductive activity of Fe2+-magnetite system in redox-oscillating environments.

Peng, Huan↗
NASA NTRS1994

A revised analysis of micron-sized particles detected near Saturn by the Voyager 2 plasma wave instrument

The impulsive noise that the plasma wave and radio astronomy instruments detected during the Voyager 2 swing by Saturn was attributed to dust grains striking the spacecraft. This report presents a reanalysis of the dust impacts recorded by the plasma wave instrument using an improved model for the response of the electric antenna to dust impacts. The fundamental assumption used in this analysis is that the voltage induced on the antenna is proportional to the mass of the impacting grain. Using the above assumption and the antenna response constants used at Uranus and Neptune, the following conclusions can be reached. The primary dust distribution consists of a 'disk' of particles that coincides with the equator plane and has a north-south thickness of 2-Delta zeta = 962 km. A less dense 'halo' with a north-south thickness of 2-Delta zeta = 3376 km surrounds the primary distribution. The dust particle sizes are of the order of 10 microns, assuming a mass density of 1 g/cu cm. The corresponding particle masses are of the order of 10(exp -9) g, and maximum number densities are of the order of 10(exp -2)/cu m. Most likely, the G ring is the dominate source since the particles were observed very close to that ring, namely at 2.86 R(sub S). Other sources, like nearby moons, are not ruled out especially when perturbations due to electromagnetic forces are included. The calculated optical depth differs by about a factor of 2 from photometric studies. The current particle masses, radii, and the effective north-south thickness of the particle distribution are larger than what Gurnett et al. (1983) reported by about 2, 1, and 1 orders of magnitude, respectively. This is attributed to the fact that the collection coefficient used in this study is smaller than what was used in Gurnett et al.'s earlier publication.

Tsintikidis, D.↗
NASA NTRS1982

Frequency-scanning particle size spectrometer

A particle size spectrometer having a fixed field of view within the forward light scattering cone at an angle .theta..sub.s between approximately 100 and 200 minutes of arc (preferably at 150 minutes), a spectral range extending approximately from 0.2 to 4.0 inverse micrometers (.mu.m.sup.-1), and a spectral resolution between about 0.1 and 0.2 .mu.m.sup.-1 (preferably toward the lower end of this range of spectral resolution), is employed to determine the distribution of particle sizes, independently of the chemical composition of the particles, from measurements of incident light, I.sub.o, at each frequency, .sigma. (=1/.lambda.), and scattered light, I(.sigma.), according to the equation: ##EQU1## where l=2.pi.sin.theta., .theta. being the fixed viewing angle .theta..sub.s at which scattered light is measured, r is particle size, .sigma. is the reciprocal of wavelength, J.sub.1 is a Bessel function of first kind and order unity, Y.sub.1 is a Bessel function of second kind and order unity. The quantity, I.sub..sigma., is the ratio of scattered light to incident light at each frequency interval. The apparatus is a passive remote sensor that can be used in laboratories, field stations, flying aircrafts and airships, and on board an orbiting satellite.

Fymat, Alain L.↗
DOE OSTI2023

System and method for controlling metal oxide gel particle size

Metal oxide gel particles, may be prepared with a desired particle size, by preparing a low-temperature aqueous metal nitrate solution containing hexamethylene tetramine as a feed solution; and causing the feed solution to flow through a first tube and exit the first tube as a first stream at a first flow rate, so as to contact a high-temperature nonaqueous drive fluid. The drive fluid flows through a second tube at a second flow rate. Shear between the first stream and the drive fluid breaks the first stream into particles of the metal nitrate solution, and decomposition of hexamethylene tetramine converts metal nitrate solution particles into metal oxide gel particles. A metal oxide gel particle size is measured optically, using a sensor device directed at a flow of metal oxide gel particles within the stream of drive fluid. The sensor device measures transmission of light absorbed by either the metal oxide gel particles or the drive fluid, so that transmission of light through the drive fluid changes for a period of time as a metal oxide gel particle passes the optical sensor. If a measured particle size is not about equal to a desired particle size, the particle size may be corrected by adjusting a ratio of the first flow rate to a total flow rate, where the total flow rate is the sum of the first and second flow rates.

Linneen, Nicholas↗
NASA NTRS1979

Frequency-scanning particle size spectrometer

A particle size spectrometer having a fixed field of view within the forward light scattering cone at an angle theta sub s between approximately 100 and 200 minutes of arc (preferably at 150 minutes), a spectral range extending approximately from 0.2 to 4.0 inverse micrometers, and a spectral resolution between about 0.1 and 0.2 inverse micrometers (preferably toward the lower end of this range of spectral resolution), is employed to determine the distribution of particle sizes, independently of the chemical composition of the particles, from measurements of incident light, at each frequency, sigma (=1/lambda), and scattered light, I(sigma).

Fymat, A. L.↗
NASA NTRS1969

Direct indication of particle size in fluidized beds

Differential pressure measurements indicate particle size and particle size distribution in fluidized beds. The technique is based on the relationship between bed particle size and the intensity and frequency of fluctuations. By measuring the fluctuations, an estimate of average particle size of the fluid-bed material can be made.

Knudsen, I. E.↗
NASA NTRS1991

The particle size of Martian aeolian dunes

The effective particle size of unconsolidated materials on the Martian surface can be determined from thermal inertia, due to a pore size dependence of thermal conductivity at Martian atmospheric pressures. Because dunes consist of a narrow range of well-sorted, unconsolidated particles, they provide for a test of the relationship between particle size and thermal inertia calculated from midinfrared emission data for the Martian surface. Two independent approaches are used. First, thermal inertia data indicate that Martian dunes have an average particle size of about 500 +/-100 microns, or medium to coarse sand. Second, expected dune particle sizes are determined from grain trajectory calculations and the particle size transition from suspension to saltation. On earth, the transition occurs for a grain when the ratio of the terminal fall velocity to the wind friction speed, u*(t) is near unity; for grains at u*(t) this occurs at about 52 microns. Terrrestrial dune sands have a mean of 250 microns and are composed entirely of grains greater than 52 microns. The corresponding Martian transition grain size is about 210 microns, suggesting that Martian dunes should be significantly coarser than terrestrial dunes. Grain saltation path length as a function of particle size also shows that, under Martian conditions, larger grains than on earth will become suspended. Both approaches indicate that Martian dune sand should be coarser than terrestrial dune sand. These results closely match the grain sizes determined from thermal inertia models, providing the first direct test of the validity of these models for actual Martian surface materials.

Edgett, Kenneth S.↗
NASA NTRS1972

The determination and optimization of (rutile) pigment particle size distributions

A light scattering particle size test which can be used with materials having a broad particle size distribution is described. This test is useful for pigments. The relation between the particle size distribution of a rutile pigment and its optical performance in a gray tint test at low pigment concentration is calculated and compared with experimental data.

Richards, L. W.↗
NASA NTRS1973

The techniques of holographic particle sizing

Depending on the mechanism of particle production, the resultant particle size and velocity distribution may range over several orders of magnitude. In general, if particle size information is desired from a given type generator, one must resort to some form of experimental determination of the distribution. If the source of particle production is a dynamic one involving a reasonable volume, holography provides a tailor-made particle size and velocity distribution detector. This is evidenced by the fact that holography allows the entire volume to be recorded on one exposure without any interference with the volume of interest. Herein lies a very important characteristic of the holographic particle detection technique: It provides a holographic nondestructive testing technique in the fullest sense of the definition of nondestructive testing. This report provides a description of three different systems useful in this technique and includes the experimental results from one of the holographic systems which was used to detect particle size and velocity distribution from the Skylab waste tank.

Kurtz, R. L.↗
DOE OSTI2023

Particle size and shape effect of Crumbler® rotary shear-milled granular woody biomass on the performance of Acrison® screw feeder: A computational and experimental investigation

Physical experiments and discrete element model (DEM) simulations are conducted to evaluate particle characteristics and operation parameter effects on screw feeding performance for rotary shear-milled Douglas fir. Three performance metrics are used: mass flow rate, shaft driving torque, and specific energy consumption. The impact of particle size, particle size distribution (PSD), shaft rotational speed (rpm), and hopper dimensions on the performance are investigated. All employed performance metrics reveal the superior flowability of the 2-mm particles in contrast to the larger 6-mm counterpart. Remarkably, wider PSD results in poorer flowability than the two mono-sized particles, proving the flowability enhancement achieved by narrower PSD of the woody feedstock. More importantly, DEM simulations unveil PSD-induced degradation in flowability is attributed to mechanical interlocking and particle segregation effects. Furthermore, higher shaft rpm causes higher mass flow rate at the cost of higher specific energy consumption due to viscous dissipation and changes in flow pattern.

09 BIOMASS FUELS↗