SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Traditional circuit analysis defines the power gain of an oscillator to be finite, since there is an output without an input. By defining power gain as the ratio of output power to input power, however, finite power gain can be characterized. Several simple circuit equations which can be used to find power gain in an oscillator circuit are presented and discussed.
In this paper we present first, the results of a study conducted to investigate the microwave performance of a wideband (25-31 GHz) GaN MMIC distributed high power amplifier (HPA). Second, we compare and contrast the above performance with that of an alternate architecture that relies on two HPAs to provide contiguous 25-31 GHz coverage. The two HPAs operate across 25-28 GHz and 27-31 GHz, respectively, and can be switched in and out depending on the need at any given time. The parameters investigated includes the output power, gain, power added efficiency, bandwidth, RMS error vector magnitude for offset-QPSK, 8PSK, 16APSK, and 32 APSK waveforms, 3rd-order intermodulation distortion products, noise figure, and single sideband phase noise.
Abstract. Yaw controllers typically rely on measurements taken at the wind turbine, resulting in a slow reaction to wind direction changes and subsequent power losses due to misalignments. Delayed yaw action is especially problematic in wake steering operation because it can result in power losses when the yaw misalignment angle deviates from the intended one due to a changing wind direction. This study explores the use of preview wind direction information for wake steering control in a two-turbine setup with a wind speed in the partial load range. For these conditions and a simple yaw controller, results from an engineering model identify an optimum preview time of 90 s. These results are validated by forcing wind direction changes in a large-eddy simulation model. For a set of six simulations with large wind direction changes, the average power gain from wake steering increases from only 0.44 % to 1.32 %. For a second set of six simulations with smaller wind direction changes, the average power gain from wake steering increases from 1.24 % to 1.85 %. Low-frequency fluctuations are shown to have a larger impact on the performance of wake steering and the effectiveness of preview control, in particular, than high-frequency fluctuations. From these results, it is concluded that the benefit of preview wind direction control for wake steering is substantial, making it a topic worth pursuing in future work.
The feasibility of Ka-band GaN-on-SiC MMIC based balanced power amplifier for science data downlinks from NASA’s lunar mission assets in space is investigated. The balanced amplifier combines the RF output power from two power amplifiers using a rectangular waveguide based 3-dB hybrid coupler. The investigation includes characterizing the balanced amplifier for the overall RF output power, Gain, power added efficiency, RMS error vector magnitude for offset-QPSK, 8PSK, 16APSK, and 32APSK waveforms, 3rd order intermodulation products, and noise figure. The balanced amplifier has high output RF power and good linearity and can support high data rate downlinks from the surface and vicinity of the Moon to Earth.
A cognitive radio on a future NASA near-Earth spacecraft will be capable of sensing its environment and dynamically adapting its operating parameters to provide the desired SATCOM service to the mission. A key component that can enable this type of operation is a high-power amplifier (HPA) that resides on the radio platform. In this paper, we present the RF performance characteristics of a Ka-band gallium nitride (GaN) monolithic microwave integrated circuit (MMIC) based HPA for cognitive radio platforms. These characteristics include the output power, gain, power added efficiency (PAE), RMS error vector magnitude (EVM), spectral efficiency, 3rd-order intermodulation distortion (IMD) products, spectrum, spectral regrowth, noise figure (NF), and phase noise. The data presented indicates that the HPA meets NTIA, military, and commercial spectral mask requirements. In addition, we discuss the benefits offered by the above performance characteristics toward the design and implementation of a cognitive radio platform. Furthermore, as examples, we discuss three potential use cases that apply artificial intelligence (AI) and machine learning (ML) techniques and exploit the performance characteristics discussed above to provide a knowledge-based cognitive radio platform design for SATCOM. Thus, cognitive radios with performance flexibility can enable roaming and provide seamless interoperability autonomously in the future between NASA, commercial, and other space networks owned by U.S. government agencies.
A cognitive radio on a future NASA near-Earth spacecraft will be capable of sensing its environment and dynamically adapting its operating parameters to provide the desired SATCOM service to the mission. A key component that can enable this type of operation is a high-power amplifier (HPA) that resides on the radio platform. In this report, we present the RF performance characteristics of a Ka-band gallium nitride (GaN) monolithic microwave integrated circuit (MMIC) based HPA for cognitive radio platforms. These characteristics include the output power, gain, power added efficiency (PAE), RMS error vector magnitude (EVM), spectral efficiency, 3rdorder intermodulation distortion (IMD) products, spectrum, spectral regrowth, noise figure (NF), phase noise, and group delay. The data presented indicates that the HPA meets NTIA, military, and commercial spectral mask requirements. In addition, we discuss the benefits offered by the above performance characteristics toward the design and implementation of a cognitive radio platform. Furthermore, as examples, we discuss three potential use cases that apply artificial intelligence (AI) and machine learning (ML) techniques and exploit the performance characteristics discussed above to provide a knowledge-based cognitive radio platform design for SATCOM. Thus, cognitive radios with performance flexibility can enable roaming and provide seamless interoperability autonomously in the future between NASA, commercial, and other space networks owned by U.S. government agencies.
The paper demonstrates a spectrally efficient Ka-band GaN MMIC based high-power amplifier (HPA) that uses a waveguide 4-port magic-tee as a 2-way power combiner to combine the output from two lower power amplifier circuits. The paper presents for the prototype HPA the measured output power, gain, power added efficiency, error vector magnitude for Offset-QPSK, 8PSK, 16APSK, 32APSK, and 16QAM waveforms, waveform spectrum, and out-of-band spectral regrowth. The HPA is intended for establishing a direct communication link between assets on the lunar surface/orbit and Earth.
Output power and gain saturation characteristics for high speed flowing gas molecular lasers, discussing electrically excited fluid mixing carbon dioxide laser
Power gain in spacecraft power supply obtained by switching off digital computer system
In this paper, we report the high-performance radio-frequency transistors based on the single-walled semiconducting carbon nanotubes with a refined average diameter of ∼1.6 nm. These diameter-separated carbon nanotube transistors show excellent transconductance of 55 μS/μm and desirable drain current saturation with an output resistance of ∼100 KΩ μm. An exceptional radio-frequency performance is also achieved with current gain and power gain cut-off frequencies of 23 GHz and 20 GHz (extrinsic) and 65 GHz and 35 GHz (intrinsic), respectively. These radio-frequency metrics are among the highest reported for the carbon nanotube thin-film transistors. This study provides demonstration of radio frequency transistors based on carbon nanotubes with tailored diameter distributions, which will guide the future application of carbon nanotubes in radio-frequency electronics.
Depletion-mode InGaAs microwave power MISFETs with 1-micron gate lengths and up to 1-mm gate widths have been fabricated using an ion-implantation process. The devices employed a plasma-deposited silicon/silicon dioxide gate insulator. The dc I-V characteristics and RF power performance at 9.7 GHz are presented. The output power, power-added efficiency, and power gain as a function of input power are reported. An output power of 1.07 W with a corresponding power gain and power-added efficiency of 4.3 dB and 38 percent, respectively, was obtained. The large-gate-width devices provided over twice the previously reported output power for InGaAs MISFETs at X-band. In addition, output power stability within 1.2 percent over 24 h of continuous operation was achieved. In addition, a drain current drift of 4 percent over 10,000 sec was obtained.
The output power from a single gallium nitride (GaN) high electron mobility transistor (HEMT) based monolithic microwave integrated circuit (MMIC) power amplifier (PA) chip is limited to few watts. To achieve higher power, the output from several chips have to be combined. In this paper we present, the results of a study conducted to investigate a 2-way power combiner to combine the output power from two GaN MMIC based high power amplifier (HPA) chips The parameters investigated includes the power combiner characteristics, individual GaN MMIC based HPA output power, gain, and power added efficiency, and the overall performance of the combined amplifier.
This paper presents experimental and theoretical studies of the small signal gain and the radiant power for one configuration of CO2 gasdynamic lasers to define the optimum-gas temperature, pressure and gas compositions for the gain and the laser power. The laser was operated with two gas mixtures (CO2-N2-He and CO2-N2-H2O) at temperatures of 800-2200 deg K, pressures of 2-16 atm, and a wide range of gas compositions. For this laser optimum gas temperatures were roughly 1500-1600 deg K for gain and more than 2200 deg K for power. It was found that the gasdynamic laser would not oscillate for He or H2O concentrations of less than 10% and 1%, respectively. The various kinetic processes for establishing gain and the various laser cavity parameters that determine laser power were examined. The theories were assessed for their ability to predict gain and power. In most cases, the gain theory gave excellent quantitative results whereas the power theory gave only qualitative results. Laser power of nearly 2 kw was obtained.
The design and financing of commercial-scale floating offshore wind projects require a better understanding of how power generation differs between newer floating turbines and well-established fixed-bottom turbines. In floating turbines, platform mobility causes additional rotor motion that can change the time-averaged power generation. In this work, OpenFAST simulations examine the power generated by the National Renewable Energy Laboratory's 5-MW reference turbine mounted on the OC3-UMaine spar and OC4-DeepCWind semisubmersible floating platforms, subjected to extreme irregular waves and below-rated turbulent inflow wind from large-eddy simulations of a neutral atmospheric boundary layer. For these below-rated conditions, average power generation in floating turbines is most affected by two types of turbine displacements: an average rotor pitch angle that reduces power, caused by platform pitch; and rotor motion upwind-downwind that increases power, caused by platform surge and pitch. The relative balance between these two effects determines whether a floating platform causes power gains or losses compared to a fixed-bottom turbine; for example, the spar creates modest (3.1%–4.5%) power gains, whereas the semisubmersible creates insignificant (0.1%–0.2%) power gains for the simulated conditions. Furthermore, platform surge and pitch motions must be analyzed concurrently to fully capture power generation in floating turbines, which is not yet universal practice. Finally, a simple analytical model for predicting average power in floating turbines under below-rated wind speeds is proposed, incorporating effects from both the time-averaged pitch displacement and the dynamic upwind-downwind displacements.
The essence of this project was for diamond films to be deposited on cold cathodes to improve their emission properties. Films with varying morphology, composition, and size of the crystals were deposited and the emission properties of the cathodes that utilize such films were studied. The prototype cathodes fabricated by the methods developed during Phase I were tested and evaluated in an actual high-power RF device during Phase II. These high-power tests used the novel active RF pulse compression system and the X-band magnicon test facility at US Naval Research Laboratory. In earlier tests, plasma switches were employed, while tests under this project utilized electron-beam switching. The intense electron beams required in the switches were supplied from cold cathodes embodying diamond films with varying morphology, including uncoated molybdenum cathodes in the preliminary tests. Tests with uncoated molybdenum cathodes produced compressed X-band RF pulses with a peak power of 91 MW, and a maximum power gain of 16.5:1. Tests were also carried out with switches employing diamond coated cathodes. The pulse compressor was based on use of switches employing electron beam triggering to effect mode conversion. In experimental tests, the compressor produced 165 MW in a ~ 20 ns pulse at ~18× power gain and ~ 140 MW at ~ 16× power gain in a 16 ns pulse with a ~ 7 ns flat-top. In these tests, molybdenum blade cathodes with thin diamond coatings demonstrated good reproducible emission uniformity with a 100 kV, 100 ns high voltage pulse. The new compressor does not have the limitations of earlier types of active pulse compressors and can operate at significantly higher electric fields without breakdown.
In the SLED 1 method of RF pulse compression, two high Q resonators store energy from an RF source for a relatively long time interval (typically 3 to 5 J.1sec). Triggered by a reversal in RF phase, this stored energy is then released during a much shorter interval equal to the filling time of the accelerating structure. A peak power gain on the order of three and a compression efficiency on the order of 60% are typically attained. The shape of the output pulse is, however, a sharply decaying expo- nential. In SLED-II the two cavities are replaced by two lengths of resonant line, forming a Resonant Line SLED (RELS) and resulting in a flat output pulse. Therefore, RELS stages can be cascaded to give a greater peak power gain. Using two stages, a peak power gain greater than ten can be achieved with a reasonable compression efficiency. Unlike the BEC,2 the RELS compression fac- tor per stage is not limited to two, albeit at the expense of intrinsic efficiency. Like the BEC, it uses long lines rather than short cavities.
The power gain and thrust for plasma engines available by unreeling 10 km of insulated Al wire from a spacecraft are investigated. The wire, unreeling in the vertical, would cut the earth's magnetic field lines, thereby generating 20 kW of power in the wire. A drag loss of 20.4 kJ/sec would reduce the power gain to 18.7 kW, an efficiency of 92 percent. Thicker wires could push the power gain to 1 MW at 95 percent efficiency. Conductive 'balloons' at the ends of the tether would function as ionospheric 'brushes' to complete the circuit. Reversing the IXB force by employing on-board stored power would drive the tether current against the induced voltage, providing a 1 N thrust for 8 kW of energy consumed, which could be supplied by solar panels during the day portion of orbit. The equivalent thrust by conventional stationkeeping means would consume 8000 kg of propellant/yr. Techniques for stabilizing the tether in the presence of variable magnetic fields are discussed.
Abstract. Wind farm flow control represents a category of control strategies for achieving wind-plant-level objectives, such as increasing wind plant power production and/or reducing structural loads, by mitigating the impact of wake interactions between wind turbines. Wake steering is a wind farm flow control technology in which specific turbines are misaligned with the wind to deflect their wakes away from downstream turbines, thus increasing overall wind plant power production. In addition to promising results from simulation studies, wake steering has been shown to successfully increase energy production through several recent field trials. However, to better understand the benefits of wind farm flow control strategies such as wake steering, the value of the additional energy to the electrical grid should be evaluated – for example, by considering the price of electricity when the additional energy is produced. In this study, we investigate the potential for wake steering to increase the value of wind plant energy production by combining model predictions of power gains using the FLOw Redirection and Induction in Steady State (FLORIS) engineering wind farm flow control tool with historical electricity price data for 15 existing US wind plants in four different electricity market regions. Specifically, for each wind plant, we use FLORIS to estimate power gains from wake steering for a time series of hourly wind speeds and wind directions spanning the years 2018–2020, obtained from the ERA5 reanalysis dataset. The modeled power gains are then correlated with hourly electricity prices for the nearest transmission node. Through this process we find that wake steering increases annual energy production (AEP) between 0.4 % and 1.7 %, depending on the wind plant, with average increases in potential annual revenue (i.e., annual revenue of production, ARP) 4 % higher than the AEP gains. For most wind plants, ARP gain was found to exceed AEP gain. But the ratio between ARP gain and AEP gain is greater for wind plants in regions with high wind penetration because electricity prices tend to be relatively higher during periods with below-rated wind plant power production, when wake losses occur and wake steering is active; for wind plants in the Southwest Power Pool – the region with the highest wind penetration analyzed (31 %) – the increase in ARP from wake steering is 11 % higher than the AEP gain. Consequently, we expect the value of wake steering, and other types of wind farm flow control, to increase as wind penetration continues to grow.