Engineering PapersSearch

SEARCH · Engineering Papers

Results for “PEO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Molecular-level Regulation of PEO-Based Electrolytes with CaF 2 Nanoparticles for Advanced Solid-State Lithium Metal Batteries

The poly(ethylene oxide) (PEO)-based electrolyte has caught much attention for its flexibility, interfacial compatibility, and low cost, but the low ionic conductivity and poor mechanical strength severely hinder its further application in solid-state batteries. Herein, a molecular level regulation through adding CaF 2 nanoparticle fillers is proposed to enhance the electrochemical performance of the PEO-based electrolyte. The strong coordination effects of the Ca cation with a Li salt anion and ether-oxygen increase the dissociated Li ion concentration and accelerate Li ion migration, thus enhancing the ionic conductivity of the electrolyte when combined with their physical disruption in the PEO matrix (0.31 mS cm -1 at 55 °C). Moreover, the spontaneous reaction between Li and CaF 2 generates a LiF-rich solid electrolyte interphase, which promotes homogeneous Li deposition. Consequently, the PEO-CaF 2 electrolyte delivers symmetric cells over 6300 h and maintains full batteries over 1000 cycles with 80% capacity retention. In conclusion, the assembled pouch-cell displays robust performance, further demonstrating its potential practical application.

Li, Tao [Lanzhou Univ. (China)] (ORCID:00000003196

Solid State Electrolytes Prepared from PEO (360) Silanated Silica

All solid state composite electrolytes were prepared using fumed silica (SiO2) silanated with an oligomeric polyethylene oxide (PEO) silane containing 6-9 ethylene oxide repeat units, a PEO matrix and LiClO4 (8/1 O/Li). The PEO-silane covalently attached to the silica was amorphous, with a T(sub g) that increased from -90 C to -53 C after attachment. The conductivity of films prepared using the PEO-silanated silica increased to approx. 6 x 10(exp -5) S/cm at RT compared with approx. 1 x 10(-5) S/cm for films prepared with unsilanated SiO2.

Maitra, P.

Inter and Intra Molecular Phase Separation Environment Effects on PI-PEO Block Copolymers for Batteries and Fuel Cells

Rod-coil molecules have been introduced as a novel type of block copolymers with unique microstructure due to their ability to self-assemble to various ordered morphologies on a nanometer length scale. These molecules, comprised two homo polymers joined together at one end, microphase separate into ordered, periodic arrays of spheres, cylinders in the bulk state and or solution. To get ordered structure in a reasonable scale, additional force field are applied, such as mechanical shearing, electric field and magnetic field. Recently, progress has made it a possible to develop a new class of polyimides (PI)-Polyethylene oxide (PEO) that are soluble in polar organic solvents. The solvent-soluble PI-PEO has a wide variety of applications in microelectronics, since these PI-PEO films exhibit a high degree of thermal and chemical stability. In this paper, we report the self-assembled ordered structure of PI-PEO molecules formed from concentrate solution.

Xue, Chen-Chen

Manufacturing, Characterization and Terrestrial Passive Radiative Cooling Performance of Nanofibrous PTFR-PEO Composite Thermal Coatings

Passive heat management is desirable in many applications since it can reduce the energy expended for cooling, for example, in buildings and automobiles. Specifically, materials with wavelength-dependent reflectance and emittance can manage incident solar fluxes while enabling passive radiative cooling by thermal emission. This study demonstrates the use of polymeric nanofibers, specifically polytetrafluoroethylene (PTFE) and polyethylene oxide (PEO) composite, as thermal coatings for passive temperature control. Employing the electrospinning fabrication process, we engineer nano and micro-scale fibrous structures, studying the influence of fabrication parameters, such as precursor material concentration and rotating collector speed, on fiber geometry and optical properties. To understand the role of material and fiber geometry on optical performance, we characterize various samples' spectral reflectance, absorptance, and transmittance using spectrophotometers interfaced with integrating spheres. The results show the potential of nanofabricated PTFE-PEO coatings as promising candidates for passive thermal control. We highlight their competitive edge by comparing their solar reflectance and emittance values to existing passive radiative thermal control materials. In essence, this study contributes to advancing passive heat management technologies, offering insights into optimizing material composition and fabrication techniques for enhanced performance in various applications.

Chieloka Ibekwe

Homopolyrotaxanes and Homopolyrotaxane Networks of PEO

In order to identify the optimum size of macrocrown ether for threading, we first investigated the size and shape of simple crown ethers in the melt at 373 K, and their extent of threading with PEO in the melt using coarse-grained Monte Carlo simulations on the 2nnd (second nearest neighbor diamond) lattice, which is a high coordination lattice whose coarse-grained chains can be reverse mapped into fully atomistic models in continuous space.

Pugh, Coleen

Crystallization of Bottlebrush Statistical Copolymers of Polystyrene and Poly(ethylene oxide)

Here, bottlebrush statistical copolymers (BSCPs) with poly(ethylene oxide) (PEO) and polystyrene (PS) side chains grafted to a polynorbornene (PNB) backbone were synthesized by ring-opening metathesis polymerization (ROMP). The impact of the glassy PS side chains on the crystallization of the PEO side chains as a function of the backbone length, grafting densities, and fraction of the PS and PEO side chains is described. The bottlebrush architecture, where the side chains are anchored to the backbone, inherently constrains the mobility of PEO. Compared with the bulk crystallization temperature of PEO, the higher glass transition temperature of PS places further constraints on PEO crystallization. The limited mobility of PEO leads to cold crystallization behavior during heating. Reduced grafting densities, in turn, reduce side-chain crowding, leading to less extended pendant structures. The degree of crystallinity of PEO was found to decrease at lower grafting densities to a point where crystallization was not observed. The average distance between bottlebrush backbones increased linearly with the backbone length, suggesting that the backbone forms a distinct mesodomain. For BSCPs with asymmetric volume fractions of PS and PEO side chains, the degree of crystallinity of PEO increases with a change from cold crystallization to normal nucleation and growth during cooling, as a result of reduced constraints on PEO mobility by the glassy PS side chains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH

Backbone Stitching in Bottlebrush Copolymer Mesodomains and the Impact of Side Chain Crystallization

We synthesized bottlebrush statistical copolymers (BSCPs) having poly­(ethylene oxide) (PEO) and poly­(dimethylsiloxane) (PDMS) side chains attached to a polynorbornene backbone. Small-angle X-ray scattering analysis showed that for densely grafted BSCPs, the scattering length density gradually transitions between the PEO and PDMS domains. For loosely grafted BSCPs, the polymer backbone formed a distinct mesodomain, with a lower electron and mass density than both the PEO and PDMS domains. The bottlebrush backbone essentially “stitches” the PEO and PDMS side chains, looping back and forth from the PEO to PDMS domains with the backbone segments oriented normal to the domain interfaces. Self-consistent field theory (SCFT) calculations validated the stitching of the backbone driven by the microphase separation of PEO and PDMS, along with a strong segmental order of the side chains in the melt. The reduced birefringence upon PEO crystallization suggests the disruption of the strong segmental order by the crystallization. Both the static intrinsic and the form birefringences of the BSCPs decreased upon PEO crystallization. Solid-state NMR confirmed the rigidity of PEO crystallites and the bottlebrush backbone. Self-assembly of BSCPs containing polyhedral oligomeric silsesquioxane (POSS) pendent groups was also evaluated by X-ray scattering, showing the formation of lamellar microdomains that inhibited POSS crystallization.

Hu, Mingqiu

Establishing the Stability of Cross-Linked Poly(ethylene oxide) Blended with Poly(pentyl malonate) against Lithium Metal Anodes

This work focuses on an electrolyte obtained by infusing linear poly(pentyl malonate) (PPM) chains into cross-linked poly(ethylene oxide) (PEO). A lithium salt is added to enable ion transport. Obtaining this electrolyte is only possible because PPM is miscible with PEO irrespective of salt concentration. The properties of this electrolyte are compared against two benchmarks: an electrolyte obtained by infusing linear PEO into cross-linked PEO and cross-linked PEO with no added linear polymer. Measurements of storage moduli and ion transport efficacies are found to be similar across the three electrolytes, suggesting similar stability behavior against lithium metal anodes, based on current theoretical models. Instead, the PPM infused electrolyte outperforms the other two electrolytes. In the cycling tests, the current supported by the PPM infused electrolyte was a factor of 20 higher than that of the PEO infused electrolyte and a factor of 4 higher than that of the cross-linked PEO electrolyte. In the unidirectional plating experiments, the other two electrolytes fail after about 4 h or less, while the PPM containing electrolyte did not fail during the 140 h testing period. Insight into the nature of failure modes was obtained using synchrotron hard X-ray microtomography.

Gido, Lily [University of California, Berkeley]

Upcycling waste PET into functional multiblock copolymers through controlled macromolecular design

Poly(ethylene terephthalate) (PET) oligomers derived from glycolysis depolymerization were converted into multiblock copolymers through diisocyanate-mediated coupling with dihydroxy-terminated oligomers, enabling precise control over copolymer sequence distribution, connectivity, and mechanical performance. Here, we demonstrate that telechelic PET oligomers isolated directly from depolymerized consumer waste can serve as reactive building blocks for the formation of segmented multiblock copolymers, eliminating the need to revert to monomeric feedstocks. Dihydroxy-terminated PET oligomers (Mw ≈ 8 kg mol−1) were coupled with poly(ethylene oxide) (PEO, Mw ≈ 4 kg mol−1) to form PET-PEO multiblock copolymers with high molar mass (Mw ≈ 160 kg mol−1). We further show that the timing of end-capping reactions provides a key control parameter that governs the competition between chain extension and termination, thereby dictating the resulting multiblock architecture and molecular-weight evolution. Evaluation of their mechanical properties reveals that virgin PET exhibits high modulus (∼3 GPa) and strength (43 MPa) but limited ductility (<10% elongation). In contrast, PET–PEO multiblock copolymers retain comparable tensile strength (44 MPa), albeit while exhibiting dramatically enhanced ductility (>90% elongation), forming tougher materials with efficient stress transfer between the rigid PET domains and the flexible PEO segments. When incorporated into PET/PEO blends at low loadings, the multiblock copolymers serve as effective compatibilizers, yielding materials with an intermediate modulus (1.1–1.2 GPa) and improved elongation compared to uncompatibilized blends. Furthermore, the presence of PEO blocks increases water uptake and gas permeability relative to virgin PET, reflecting the tunability of molecular transport through the copolymeric blocks. To our knowledge, this represents the first report of PET–PEO multiblock copolymers derived from post-consumer PET for gas transport applications. These results demonstrate that multiblock copolymer formation from telechelic PET oligomers provides a versatile platform for tailoring the mechanical and transport behavior of polyester-based materials through controlled macromolecular design and establishes a generalizable strategy for transforming consumer plastic waste into functional segmented polymers without requiring complete depolymerization to monomers.

Watson-Sanders, Shelby [Department of Chemistry, U

Confocal Raman Microscopy for Measuring In Situ Temperature-Dependent Structural Changes in Poly(Ethylene Oxide) Thin Films

Crystallization from the melt is a critical process governing the properties of semi-crystalline polymeric materials. While structural analyses of melting and crystallization transitions in bulk polymers have been widely reported, in contrast, those in thin polymer films on solid supports have been underexplored. Herein, in situ Raman microscopy and self-modeling curve resolution (SMCR) analysis are applied to investigate the temperature-dependent structural changes in poly(ethylene oxide) (PEO) films during melting and crystallization phase transitions. By resolving complex overlapping sets of spectra, SMCR analysis reveals that the thermal transitions of 50 µm thick PEO films comprise two structural phases: an ordered crystalline phase and a disordered amorphous phase. The ordered structure of the crystalline PEO film entirely disappears as the polymer is heated; conversely, the disordered structure of the amorphous PEO film reverts to the ordered structure as the polymer is cooled. Broadening of the Raman bands was observed in PEO films above the melting temperature (67 °C), while sharpening of bands was observed below the crystallization temperature (45 °C). The temperatures at which these spectral changes occurred were in good agreement with differential scanning calorimetry (DSC) measurements, especially during the melting transition. The results illustrate that in situ Raman microscopy coupled with SMCR analysis is a powerful approach for unraveling complex structural changes in thin polymer films during melting and crystallization processes. Furthermore, we show that confocal Raman microscopy opens opportunities to apply the methodology to interrogate the structural features of PEO or other surface-supported polymer films as thin as 2 µm, a thickness regime beyond the reach of conventional thermal analysis techniques.

Koh, Miharu [Department of Chemistry, University o

Plasma Rapid Oxidation Technique for Extending Component Tenability (PROTECT)

Additive manufacturing (AM) is increasingly utilized in aerospace applications. However, post-processing is required for many applications, so intricate designs are limited. Plasma electrolytic oxidation (PEO) was investigated as a post-processing treatment on Ti-6-4 (or Ti-6Al-4V: Alpha-beta titanium alloy with a high specific strength and excellent corrosion resistance)additively manufactured specimens. The “Keronite Black” PEO treatment reduced the surface roughness (Ra) of test specimens by approximately 0.5 μm. This reduction in Ra compared to the as-printed sample was hypothesized to benefit corrosion and fatigue properties because increased Ra is known to negatively impact corrosion and fatigue characteristics. Up to a 101% improvement in the corrosion potential (Ɛcorr) was observed. Although fatigue characteristics varied by PEO parameters, there was no significant fatigue debit due to the PEO treatment. Additionally, no effect to adhesion characteristics was observed due to PEO treatment. It is recommended that additional studies investigate the ability of PEO treatments to improve the corrosion, fatigue, chemical compatibility, radiation hardening, particle shedding characteristics, and flammability/oxidizer compatibility of aerospace additively manufactured components.

Jennifer Williams

Effects of 12-crown-4 ether on the electrochemical performance of CoO2 and TiS2 cathodes in Li polymer electrolyte cells

The effect of adding 12-crown-4 ether (12Cr4) to the polyethylene oxide (PEO) electrolyte on the electrochemical properties of cells with Li(x)CoO2 or TiS2 as the cathode was investigated. The polymer electrolyte films were: (1) PEO, LiBF4; (2) PEO, LiBF4 with 12Cr4; (3) Li(x)CoO2, PEO, and LiBF4; and (4) Li(x)CoO2, PEO, LiBF4, and 12Cr4. It was found that, although 12Cr4 improved the cell performance over cells without 12Cr4 in the shallow c/d cycles (cyclic voltammetric behavior), it did not seem to prolong the active life of the cell. The cells with CoO2 as the cathode failed after a few c/d cycles, while similar cells with TiS2 did not fail even after 12 c/d cycles. The probable cause of failure in the case of CoO2 is ascribed to the instability of the CoO2 cathode.

Nagasubramanian, G.

Achieving Electrode Smoothing by Controlling the Nucleation Phase of Metal Deposition Through Polymer‐Substrate Binding

Polymer additives [like polyethylene oxide (PEO)] are widely used for smooth electrode deposition in aqueous zinc and many other battery systems. However, the precise mechanism by which they regulate morphology and suppress dendrite formation remains unclear. In this study, the knowledge gap is addressed by using in situ electrochemical atomic force microscopy to directly observe the interfacial evolution during Zn electrodeposition and polymer adsorption on Cu substrates in the presence of varying concentrations of ZnSO 4 and PEO. Contrary to previous literature assumptions, which emphasize the binding to the growing Zn crystal surfaces or Zn 2+ ions, the results demonstrate that PEO smooths Zn films by promoting nucleation of (002)-oriented Zn platelets through interactions with the Cu substrate. Density functional theory simulations support this finding by showing that PEO adsorption on Cu modifies the interfacial energy of Zn/Cu/electrolyte interfaces, favoring the stabilization of Zn (002) on the Cu substrate, as well as confines Zn electrodeposition to a narrow near-surface region. In conclusion, these findings elucidate a novel design principle for electrode smoothing, emphasizing the importance of substrate selection paired with polymer additives that exhibit an attractive interaction with the substrate but minimal interaction with growing crystals, offering a mechanistic perspective for improved battery performance.

Electrodeposition

Engineering a biopolymer for vascular embolization based on fundamental polymer principals

Herein we describe the engineering of a potential polymer substitute to metal coils for achieving vascular embolization. Our system is based on a methacrylate end-functionalized polyethylene oxide-polypropylene oxide-polyethylene oxide (PEO-PPO-PEO) triblock copolymer which displays thermal-reversible gelation properties and FCC ordering of the original copolymer while also being able to chemically crosslink. This system shows injectability, two-step gelation, chemical crosslinking with a five-fold increase in modulus and is highly resistant to washout under physiological flow conditions. Furthermore, we show that exposure to aqueous flow imparts resistance to swelling where less than 10 % swelling was observed under physiological flow as opposed to more than 60 % under static conditions after 30 days. Auxiliary experiments with PEO-PPO-PEO copolymers of various molecular weights indicate that this phenomenon may possibly be attributed to entanglements known to occur between adjacent micelles, where the reptation time, the time for polymer disentanglement, is long compared to the flow rate.

36 MATERIALS SCIENCE

A structural and electrochemical study of perfluoropolyether-poly(ethylene oxide) solid polymer electrolytes

Solid polymer electrolytes offer attractive safety, processability, and interfacial adhesion for enabling high–energy solid-state lithium batteries, but they are often limited by narrow oxidative stability windows and low lithium-ion transference numbers. In an attempt to broaden the electrochemical stability window and increase lithium-ion transference number of poly(ethylene oxide) (PEO)-based solid polymer electrolytes, we produce an optically clear, crosslinked membrane of PEO and perfluoropolyether (PFPE) using a mixed solvent method and subsequently infuse the membrane with a lithium salt. Structural and thermal analyses reveal nanoscale phase separation between fluorocarbon and hydrocarbon domains with characteristic spacings of 7–8 nm and an elevated glass transition for the hydrocarbon phase. Consistent with this, PFPE-containing membranes exhibit substantially lower ionic conductivity than PEO analogs (dry and plasticized). The transference number and electrochemical stability are similar to pure PEO. These results demonstrate that fluorination implemented as segregated nanoscale domains does not deliver the anticipated transport or stability benefits; instead, phase separation increases tortuosity and suppresses hydrocarbon-phase dynamics. The work underscores the importance of fluorine placement and morphology control, guiding the design of partially fluorinated solid polymer electrolytes toward architectures that avoid detrimental nanoscale phase separation.

Carden, Peyton [ORNL] (ORCID:0000000162296538)

Tunable Nanoscale Structure via Divalent Ion Identity in Charged-Neutral Polymer Blends

Charged-neutral polymer blends, wherein an ioncontaining polymer is blended with a neutral polymer, are potential candidates for battery electrolytes due to their improved ion transport properties and electrochemical stability. Though electrostatic interactions in charged polymer blends can theoretically stabilize ordered nanostructures analogous to those observed in neutral block copolymers, direct experimental evidence remains limited. Here, we investigate the effects of divalent cation identity on the nanoscale morphology of charged-neutral polymer blends composed of poly(ethylene oxide) (PEO) and Mg 2+ or Ca 2+ ioncontaining polymers, poly[3-(methylacryloxy)propylsulfonyl-1-(trifluoromethanesulfonylimide)] (P(Mg(MTFSI) 2 ) or P(Ca- (MTFSI) 2 ). By tuning the size of the divalent counterion, we are able to precisely tune the ion solvation between the free cation and PEO, which acts as a solvent in this system. Differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS) measurements reveal that Mg 2+ and Ca 2+ ions induce distinct structural behavior. In both systems, the blends become more miscible as the concentration of ion-containing polymer is increased indicated by increased suppression of PEO crystallinity. At the highest concentrations of P(Mg(MTFSI) 2 ), the blends undergo microphase separation and generate nanostructures with shortranged ordering. In contrast, calcium ions, which are more readily solvated by PEO, produce more homogeneous blends characterized by a single glass-transition temperature and featureless SAXS data. The results demonstrate the novel experimental confirmation that charged-neutral polymer blends can undergo microphase separation and show that counterion identity can be exploited as a design parameter to control nanoscale morphology.

Ions

Improved interfacial li-ion transport in composite polymer electrolytes via surface modification of LLZO

Composite polymer electrolytes that incorporate ceramic fillers in a polymer matrix offer mechanical strength and flexibility as solid electrolytes for lithium metal batteries. However, fast Li + transport between polymer and Li + -conductive filler phases is not a simple achievement due to high barriers for Li + exchange across the interphase. This study demonstrates how modification of Li 7 La 3 Zr 2 O 12 (LLZO) nanofiller surfaces with silane chemistries influences Li + transport at local and global electrolyte scales. Anhydrous reactions covalently link amine-functionalized silanes [(3-aminopropyl)triethoxysilane (APTES)] to LLZO nanoparticles, which protects LLZO in air. APTES functionalization lowers the poly (ethylene oxide) (PEO)-LLZO interphase resistance to half that of unmodified LLZO and increases effective Li + transference number, while insulating Al 2 O 3 completely blocks ion exchange and lowers transference number and conductivity in PEO-lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-LLZO composites. Modeling an inner resistive interphase between LLZO and PEO surrounded by an outer conductive interphase explains non-linear conductivity trends. Solid-state 7 Li & 6 Li nuclear magnetic resonance shows Li + only exchanges between PEO-LiTFSI and some LLZO interphase, with no appreciable Li + transport through bulk LLZO. Surface functionalization is a promising path toward lowering the polymer-ceramic interphase resistance. This work demonstrates that local changes in Li + transport affect macroscopic performance, highlighting the intricate relationships between all interfaces in inherently heterogeneous composite polymer electrolytes.

25 ENERGY STORAGE

Novel Elastomeric Membranes Developed for Polymer Electrolytes in Lithium Batteries

Lithium-based polymer batteries for aerospace applications need to be highly conductive from -70 to 70 C. State-of-the-art polymer electrolytes are based on polyethylene oxide (PEO) because of the ability of its ether linkages to solvate lithium ions. Unfortunately, PEO has a tendency to form crystalline regions below 60 C, dramatically lowering conductivity below this temperature. PEO has acceptable ionic conductivities (10(exp -4) to 10(exp -3) S/cm) above 60 C, but it is not mechanically strong. The room-temperature conductivity of PEO can be increased by adding solvent or plasticizers, but this comes at the expense of thermal and mechanical stability. One of NASA Glenn Research Center s objectives in the Polymer Rechargeable System program (PERS) is to develop novel polymer electrolytes that are highly conductive at and below room temperature without added solvents or plasticizers.

Tigelaar, Dean M.