Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PEEK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Coal Enhanced PEEK Filament Production for Additive Manufacturing in Industrial Services

The project (Award DE-FE0032146), led by Baker Hughes in collaboration with the University of Wyoming, aims to develop composite PEEK (Polyether-ether-ketone) materials enhanced using coal-derived graphene-based additives suitable for additive manufacturing (3D printing). Coal char (CC), graphene oxide (GO), and reduced graphene oxide (rGO), derived from Powder River Basin (PRB) coal, were successfully integrated into commercial PEEK feedstock. The composite PEEK materials demonstrated tensile and flexural strengths and modulus, Shore hardness, and thermal properties similar to unfilled PEEK. Dielectric strength of 0.5% GO/PEEK is twice that of unfilled PEEK. However, tensile elongation and Izod impact toughness of the composite materials are lower than unfilled PEEK. The 10% CC/PEEK material also shows good recyclability albeit with slightly increased glass transition and cold crystallization temperatures. Filaments of the composite PEEK materials were fabricated using a Filabot system. 3D printing of the composite PEEK initially encountered feeding stoppage caused by the non-uniform diameter of the filament, which was resolved by reducing the nominal diameter from 1.75 to 1.65 mm. The printability of the composite PEEK filaments is limited in geometry and build time, driven by differences in base PEEK feedstock from the commercial PEEK filament at printing conditions. Prototype part printed using the composite filaments shows inconsistent bead width and bead interruption resulting in porosity. Preliminary process and economic evaluation using PRB coal char estimates the cost of GO to be $0.5/lb. Considering the small fraction expected in the composite PEEK, the GO cost is several orders of magnitude lower than the commercial PEEK filament. It is recommended that the printability of composite PEEK filaments to be improved by optimizing the composite PEEK material at the printing conditions and reducing the variations in filament extrusion. Also important is to identify the mechanisms of how coal-derived additives affect the composite PEEK performance and printing characteristics to allow customized material design and processing for target performance.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

Additively Manufactured Carbon Fiber-Reinforced Siliconized Silicon Carbide Composites Using Carbon Fiber-Reinforced Poly-Ether-Ether-Ketone (PEEK) as a Precursor

Herein, we report a method to additively manufacture carbon fiber-reinforced siliconized silicon carbide composites. The process involves the pyrolysis of a 3D-printed carbon fiber-reinforced poly-ether-ether-ketone (PEEK) composite to produce a porous carbon fiber-reinforced carbon matrix composite preform, which is subsequently infiltrated with molten silicon to obtain a carbon fiber-reinforced siliconized silicon carbide composite. A key aspect of the method is limiting polymer melt flow during pyrolysis of PEEK, which is achieved by thermally annealing the 3D-printed carbon fiber-reinforced PEEK preform in air at a temperature below PEEK’s melting temperature. Rheological and differential scanning calorimetry (DSC) measurements demonstrate that the thermal annealing treatment altered the melting behavior of PEEK, while NMR and FTIR measurements provided a mechanistic explanation for the structural changes responsible for the behavior. It was also found that dimensional changes during pyrolysis were anisotropic with greater shrinkage in the stacking direction of the material.

Yoon, Bola [ORNL] (ORCID:0000000260875373)↗
DOE OSTI2025

Investigating intermolecular interactions among CO 2 , water and PEEK-ionene membrane using cryo ToF-SIMS and isotopic labeling

Cryogenic time-of-flight secondary ion mass spectrometry (cryo ToF-SIMS) has emerged as a powerful tool for investigating molecular interactions, speciation, and dynamics in materials for CO 2 capture. In this study, we apply cryo ToF-SIMS to probe interactions between CO 2 , water, and PEEK-ionene membranes—a promising material for direct CO 2 capture due to its selectivity, durability, and efficiency. Despite this potential, the mechanisms governing CO 2 diffusion and the influence of water vapor on CO 2 behavior remain unclear. To address this, we loaded PEEK-ionene membranes with 13 CO 2 and D 2 O and employed cryo ToF-SIMS to visualize the 3D distribution of CO 2 and water within the membrane. While prior studies suggest that 13 CO 2 is absorbed under ambient conditions, our cryo ToF-SIMS analysis revealed no enhancement of the 13 C/ 12 C ratio, suggesting weak CO 2 -membrane interactions. As a result, CO 2 vaporizes even at low temperatures (−140°C) under vacuum conditions. In contrast, D 2 O displayed a relatively homogeneous distribution in the membrane, suggesting stronger water-membrane interactions via hydrogen bonding (18–20 kJ/mol). Interestingly, CO 2 was not detected in D 2 O-loaded membranes, indicating minimal interference from water vapor on CO 2 diffusion. As a comparison, the cryo ToF-SIMS data show that 13 CO 2 can readily react with a basic Na 2 CO 3 aqueous solution to form NaH 13 CO 3 . These findings demonstrate cryo ToF-SIMS as a critical technique for understanding gas-water-membrane interactions, offering insights for membrane functionalization to improve CO 2 capture efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Peeking into the next decade in large-scale structure cosmology with its Effective Field Theory

After the successful full-shape analyses of BOSS data using the Effective Field Theory of Large-Scale Structure, we investigate what upcoming galaxy surveys might achieve. We introduce a “perturbativity prior” that ensures that loop terms are as large as theoretically expected, which is effective in the case of a large number of EFT parameters. After validating our technique by comparison with already-performed analyses of BOSS data, we provide Fisher forecasts using the one-loop prediction for power spectrum and bispectrum for two benchmark surveys: DESI and MegaMapper. We find overall great improvements on the cosmological parameters. In particular, we find that MegaMapper (DESI) should obtain at least a 12σ (2σ) evidence for non-vanishing neutrino masses, bound the curvature Ω k to 0.0012 (0.012), and primordial inflationary non-Gaussianities as follows: f NL loc. to ± 0.26 (3.3), f NL eq. to ±16 (92), f NL orth. to ± 4.2 (27). Such measurements would provide much insight on the theory of Inflation. We investigate the limiting factor of shot noise and ignorance of the EFT parameters.

cosmological parameters from LSS↗
DOE OSTI2025

Microextraction-Single Particle-Inductively Coupled Plasma-Mass Spectrometry for the Direct Analysis of Nanoparticles on Surfaces

A novel employment of single particle-inductively coupled plasma-mass spectrometry (SP-ICP-MS) was developed, where a microextraction (ME) probe is used to sample nanoparticles from a surface and analyze them in a single analytical step. The effects of several parameters on the performance of ME-SP-ICP-MS were investigated, including the flow rate, choice of carrier solution, particle size, and the design of the microextraction probe head itself. The optimized ME-SP-ICP-MS technique was used to compare the extraction efficiency (EE, defined as the ratio of particles measured to particles deposited on the surface) of the commercial probe head to a newly designed SP polyether ether ketone (PEEK) probe head. The SP PEEK probe head was found to have increased EE compared to the commercial probe head (8.5 ± 3% vs 3.9 ± 3%, respectively). Increasing the carrier solution flow rate was found to decrease the total analysis time at the cost of decreasing EE. Extraction efficiencies for ME-SP-ICP-MS were typically 4–10%, which is similar to transport efficiencies (1–10%) for conventional SP-ICP-MS. Lastly, ME-SP-ICP-MS was employed for the analysis of nano- and microparticles. The sizes of gold nanoparticles, 30 ± 3 and 51 ± 1.9 nm (certified sizes), and iron-based microparticles, 1000 ± 50 nm (certified size), were accurately determined to be 32.2 ± 2.5, 50.8 ± 3.4, and 1030 ± 57 nm, respectively, by ME-SP-ICP-MS. Further, this work demonstrates the potential of ME-SP-ICP-MS for the direct analysis of particles on common collection surfaces (GSR tabs, carbon planchettes, etc.) while retaining spatial information on particle distribution across the surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Gamma Radiation Effects in Amorphous and Crystalline Polyaryletherketones

This work investigates the effect of gamma radiation on chain scission and crosslinking in polyaryletherketone (PAEK) thermoplastic filaments, namely, polyetheretherketone (PEEK) and polyetherketoneketone (PEKK) that is either semicrystalline (PEKK-c) or highly amorphous (PEKK-a). The PAEK thermoplastic filaments were exposed to total ionizing doses (TID) of gamma radiation from 1 to 8 MGy in the Gamma Irradiation Facility at Sandia National Laboratories. A combination of thermal and FT-IR spectral analysis of the irradiated specimens was used to study the chain scission and crosslinking behavior between PEEK, PEKK-c, and PEKK-a. Crystallinity decreased with increased TID and melt enthalpy decreased. Despite clear indications of changes to melt and crystallization behavior, any change to the glass-transition temperature was minor until a post-irradiation thermal annealing occurred, which caused an increase in crystallinity. Gamma radiation impacted PEKK-a more due to the lower degree of initial crystallinity, where a reduction in melt enthalpy, crystallinity, and crystallization kinetics was observed. Despite these effects, the ability to achieve a higher degree of crystallization (X c < 20%) by annealing was not affected. The results presented here provide important insight into the performance of a class of commercialized PEKK thermoplastics exposed to a harsh radiation environment.

Crystallinity↗
DOE OSTI2025

Mechanical Design of the PIP-II ORBUMP Pulsed Dipole Magnet

The Proton Improvement Plan II (PIP-II) project is a vital upgrade to the Fermilab accelerator complex. The magnet pulse rate of the PIP-II Injection system requires an increase from the current rate of 15 Hz to 20 Hz as well as a roughly 30% increase in the magnetic field of the new Orbital Bump (ORBUMP) pulsed dipole magnets in the Booster. Here, the ORBUMP magnet mechanical design is presented in this paper. The ORBUMP magnet is secured in a vacuum box and the core is made up of 0.127 mm thick, low carbon steel laminations with a C-5 inorganic magnesium phosphate coating. The core is clamped using external tie bars welded to the core end plates. ANSYS Finite Element Analysis (FEA) was used to evaluate the clamping design to minimize the deflection of the core post welding of the tie bars. The water-cooled, single turn coil, which shapes the magnetic field by acting as the pole tips, is critical for the integrated field homogeneity. The coil manufacturing tolerances and fabrication techniques were evaluated to ensure the magnetic properties of the magnet could be obtained. The coil is electrically isolated from the core using virgin Polyether ether ketone (PEEK) insulating material in the gap. An investigation into the high voltage performance of the virgin PEEK insulator was conducted via partial discharge testing using a 1:1 scale sample.

Karas, D. [Fermi National Accelerator Laboratory (↗
DOE OSTI2025

Mechanical Design of the PIP-II ORBUMP Pulsed Dipole Magnet

The Proton Improvement Plan-II (PIP-II) is a vital upgrade to Fermilab's accelerator complex. The upgrade is designed to power the world s most intense high-energy neutrino beam in future experiments. The magnet pulse repetition rate of the PIP-II injection system is being upgraded from 15 Hz to 20 Hz and requires a roughly 30% increase in the magnetic field of the new Orbital Bump (ORBUMP) magnets in the Booster. The magnet is secured in a vacuum box and the core is made up of 0.127 mm thick, low carbon steel laminations with a C-5 inorganic coating. The core is clamped using external tie bars welded to the core end plates. ANSYS Finite Element Analysis (FEA) was used to evaluate the clamping design to minimize the deflection of the core post welding of the tie bars. The water-cooled single turn coil is electrically isolated from the core using virgin PEEK insulating material in the gap. An investigation into the high voltage performance of the virgin PEEK insulator was conducted. The design of the coil which shapes the magnetic field by acting as the pole tips is critical for the integrated field homogeneity. The coil manufacturing tolerances and fabrication techniques were evaluated to ensure the magnetic properties of the magnet could be obtained. The ORBUMP magnet mechanical design is presented in this paper.

Karas, Dino [Fermilab] (ORCID:0000000304340670)↗
DOE OSTI2025

Cryogenic Gear System for ADMX Tuning Cavity

The Axion Dark Matter Experiment (ADMX) searches for axions by converting them into detectable photons using resonant microwave cavities at cryogenic temperatures. A precise tuning system is needed to adjust cavity frequency without adding thermal load or electromagnetic interference. This project developed and tested a 1000 to 1 gear reduction system made from PEEK, a low thermal conductivity plastic with good dimensional stability and self lubrication at low temperatures. A compound gear train design of five 3 to 1 stages and one 4 to 1 stage achieves high reduction within a 40 mm diameter compact housing. Prototypes were 3D printed and later CNC machined in PEEK using Fusion 360 and Bantam Tools to confirm manufacturability. Prototype testing showed smooth gear engagement and no slipping. The final gearbox improves cavity tuning precision for axion searches while protecting cryogenic conditions.

Ortega, Giancarlo [Marquette U.]↗
DOE OSTI2026

Characterization of UV optical components for photon detector calibration in liquid argon TPCs

Large liquid argon time projection chambers (LArTPCs)require stable and well-characterized delivery of ultraviolet (UV)light for in situ calibration of photosensors at cryogenictemperatures. This article reports bench-top and cryogenicmeasurements of the optical components used in a UV lightcalibration system, including multi-mode fused-silica fibers,SMA-to-SMA connectors, optical fiber feedthroughs, andlight-diffuser assemblies. Light loss in several fiber types and SMAconnectors was measured across wavelengths from275–970 mm. In addition,light-loss measurements of the tested fibers after severalliquid-nitrogen thermal cycles showed no statistically significantdegradation relative to baseline measurements, and high-rate pulsedexposure (30–90 million pulses from a275 nm LED) likewise showed nomeasurable aging in jacketed fibers. A compact, palm-sized,3D-printed PEEK diffuser housing with stacked UV-grade fused-silicadiffusers yields Lambertian emission and the most uniform angulardistribution. Optical components exhibiting improved UV transmissionwere deployed successfully in multiple DUNE small- and large-scaleprototypes, demonstrating reliable operation of UV light calibrationsystem. These findings inform component selection and calibrationprocedures for achieving reliable, uniform UV light delivery inlarge-scale cryogenic detectors such as DUNE.

Behera, B. [South Dakota Sch. Mines Tech.] (ORCID:↗
NASA NTRS2026

Beyond Melting: Amorphous Bonding for Joining and Consolidation

Crystallization may be the hidden constraint in thermoplastic composite manufacturing. It requires tightly controlled cooling, induces residual stresses through shrinkage, and introduces path-dependent behavior that complicates predictive modeling yet remains essential for structural performance. This work asks: can bonding be achieved without relying on melt-driven crystallization? To address this, thin (5–20 μm) polyetherimide (PEI) interlayers are pre-healed to slow-cooled polyaryletherketone (PAEK) in two contexts. The first, Thermabond®, is sub-melt joining of low melt-PAEK laminates. Results show that bond quality is governed primarily by processing (i.e., adequate healing and film handling) rather than modest changes in interlayer thickness. This concept is then extended to laminate-scale manufacturing through an architecture known as OATMEAL (Out-of-autoclave Amorphous/semicrystalline Thermoplastic Material for Energy-efficient Aerospace-grade Laminates). PEI is healed to carbon fiber reinforced polyetheretherketone (PEEK) at the prepreg and excess PEI is then ablated from the surface. Crystallinity is developed off-line during prepreg fabrication, while subsequent consolidation occurs below the melt temperature to preserve it. Cross-ply warpage experiments show that, contrary to intuition, repeated amorphous interfaces reduce global curvature by lowering the effective stress lock-in temperature and eliminating crystallization shrinkage from the lamina response. Correspondingly, laminate behavior is accurately predicted using classical laminate theory (CLT) with a single effective stress-free temperature, whereas conventional CF/PEEK requires accounting for crystallization-driven effects. By decoupling interfacial healing from crystallization, OATMEAL enables sub-melt consolidation, reduces energy consumption by up to 75%, and increases manufacturing throughput by fivefold. These results demonstrate that amorphous bonding is not only a joining strategy, but a pathway to more predictable and scalable thermoplastic composite manufacturing.

solidification↗
DOE OSTI2025

Mechanical and Thermal Characterization of Additively Manufactured Carbon/Nylon 12 and Carbon/PEEK Composites

This study explores additive manufacturing of carbon fiber-reinforced thermoplastic composites using the Composite-Based Additive Manufacturing (CBAM) process. Carbon/Nylon 12 and Carbon/PEEK composites were fabricated and evaluated through mechanical (compression, tensile, flexural, and impact) and thermal (DSC and TGA) tests. Carbon/PEEK exhibited superior mechanical performance, with 97.5% higher tensile strength, 79.8% higher elastic modulus, and 59.6% higher flexural strength compared to Carbon/Nylon 12. Thermal testing showed that Carbon/PEEK had higher thermal stability, beginning degradation at 350 °C versus 298 °C for Carbon/Nylon. These results indicate that CBAM-fabricated Carbon/PEEK composites are suitable for applications requiring high strength and temperature resistance.

Additive manufacturing↗
DOE OSTI2025

Giant coercivity and enhanced intrinsic anomalous Hall effect at vanishing magnetization in a compensated kagome ferrimagnet

Ferrimagnets that can be driven to magnetic compensation show promise for use in spintronics as they exhibit a finite anomalous Hall effect at zero magnetic field without having a substantial magnetic moment. Compensated ferrimagnet spintronic devices with both a large anomalous Hall effect and a high coercivity would be simultaneously easy to read and difficult to erase. The kagome ferrimagnet TbMn 6 Sn 6 has been reported to host a large intrinsic anomalous Hall effect. Here, we demonstrate that doping the Mn sites with Cr drives the system toward magnetic compensation. For nearly compensated compositions at low temperatures, giant coercive fields exceeding 14 T are observed. Additionally, Cr doping markedly enhances the intrinsic anomalous Hall effect, which can be attributed to a shift in the Fermi level. Our results extend the range of unique magnetic states observed in kagome materials, demonstrating that chemical doping is an effective strategy to tune and realize these states.

DeStefano, Jonathan M. [Univ. of Washington, Seatt↗
DOE OSTI2026

Reimagining Heating, Ventilation, and Air Conditioning for New Manufactured Homes

Manufactured homes represent one of the most affordable paths to home ownership for American households, but minimum-efficiency equipment and poor-quality home installation can lead to excess energy use and high operating costs. Slipstream, with partners from the Florida Solar Energy Center (FSEC), Northwest Energy Works, and Washington State University, identified and tested manufactured home HVAC innovations targeted for new construction offering the most promising mix of improved energy performance and likelihood of industry uptake.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

A Deep, High-angular-resolution 3D Dust Map of the Southern Galactic Plane

We present a deep, high-angular-resolution 3D dust map of the southern Galactic plane over 239° < l < 6° and ∣ b∣ < 10° built on photometry from the DECaPS2 survey, in combination with photometry from VISTA Variables in the Via Lactea, the Two Micron All Sky Survey, and “Unofficial” Wide-field Infrared Survey Explorer and parallaxes from Gaia Data Release 3 where available. To construct the map, we first infer the distance, extinction, and stellar types of over 700 million stars using the brutus stellar inference framework with a set of theoretical MESA Isochrone and Stellar Tracks (MIST) stellar models. Our resultant 3D dust map has an angular resolution of 1′ , roughly an order of magnitude finer than existing 3D dust maps and comparable to the angular resolution of the Herschel 2D dust emission maps. We detect complexes at the range of distances associated with the Sagittarius-Carina and Scutum-Centaurus arms in the fourth quadrant, as well as more distant structures out to a maximum reliable distance of d ≈ 10 kpc from the Sun. The map is sensitive up to a maximum extinction of roughly A V ≈ 12 mag. We publicly release both the stellar catalog and the 3D dust map, the latter of which can easily be queried via the Python package dustmaps. When combined with the existing Bayestar19 3D dust map of the northern sky, the DECaPS 3D dust map fills in the missing piece of the Galactic plane, enabling extinction corrections over the entire disk ∣b∣ < 10°. Our map serves as a pathfinder for the future of 3D dust mapping in the era of LSST and Roman, targeting regimes accessible with deep optical and near-infrared photometry but often inaccessible with Gaia.

Milky Way galaxy↗
NASA NTRS2026

X-Hab 2026: LiDAR-Powered Autonomous Charging Service Capability for Surface Rovers and Systems

This document details the timeline of the LiDAR-Powered Autonomous Charging Service Capability for Surface Rovers and Systems project, initiated by the Fall 2025 semester class and completed by the Spring 2026 semester class. This project focuses on developing a fully autonomous system composed of a mobile surface rover and an induction charging station with a robotic arm, both controlled by their own NVIDIA Jetson Orin Nano. Structural improvements to the rover suspension system and body eliminated excessive camber, reduced stress and strain on the plexiglass body, and improved maneuverability and durability of the rover. The charging station robotic arm was fully redesigned to increase reach while minimizing weight and increasing misalignment tolerance during docking on uneven terrain. Electrical system improvements addressed previous torque and power limitations of both the rover and charging station arm. High-torque servo motors were selected based on updated calculations which incorporated terrain slope and Factor of Safety, enabling zero-point turning for the rover and increased payload capacity of the charging station arm. Significant progress was made in autonomy and perception. The rover now employs 3D LiDAR and SLAM mapping for localization, mapping, and path planning. The Battery Monitoring System (BMS) was created to coordinate battery management between the rover and charging station. The BMS provides continuous monitoring of battery state of charge, temperature, current, and will enable the autonomous initiation, execution, and termination of the charging cycle via Bluetooth communication. Testing of the WIBOTIC induction charging system demonstrated reliable power transfer under both aligned and misaligned conditions. This project demonstrated the ability of an autonomously navigating surface rover to independently plan a path to the charging station, dock, and the charging station to autonomously deploy a robotic charging arm and initiate charging of the rover. This work details the progress made to demonstrate the feasibility of autonomous surface rover navigation and recharging systems.

Megan Steele↗