The oxygen partial pressure in solid oxide electrolysis cells with multilayer electrolytes
Not provided.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not provided.
Not Available
Not Available
A new type of in-vessel Penning gauge, the Wisconsin In Situ Penning (WISP) gauge, has been developed and successfully operated in the Wendelstein 7-X (W7-X) island divertor baffle and vacuum vessel. The capacity of the quantitative measurements of the neutral reservoir for light impurities, in particular, helium, is important for tokamaks as well as stellarator divertors in order to avoid fuel dilution and radiative energy loss. Penning gauges assisted by spectroscopy are a powerful tool to obtain the total neutral pressure as well as fractional neutral pressures of specific impurities. The WISP gauge is a miniaturized Penning gauge arrangement, which exploits the ambient magnetic field of magnetic confinement fusion experiments to establish the Penning discharge. Then, in situ spectroscopy is conducted to separate the fractional neutral pressures of hydrogen, helium, and possibly also other impurities. The WISP probe head was qualified using the magnetic field of the Magnetized Dusty Plasma Experiment at Auburn University between 0.25 T and 3.5 T [E. Thomas et al ., J. Plasma Phys. 81, 345810206 (2015)]. The in-depth quantitative evaluation for hydrogen and helium will be shown as well as an exploration of nitrogen, argon, and neon. A power law scaling between current I and pressure p, I = f (Gas,V) p n⁽Gas, B⁾ , was shown. The factor f is gas and anode potential dependent, while n is gas and magnetic field strength dependent. Pressure measurements from 0.1 mbar and down to 1 × 10 -5 mbar were achieved, demonstrating a reliable operating range for relevant pressure levels in the divertor and main vessel regions in current and future fusion devices, with a time resolution of up to 1 kHz. The lowest achievable pressure measurement increases with an increase in B and can be shifted with the anode potential V . At W7-X, the WISP probe head was mounted on an immersion tube setup that passes through the cryostat and places the probe head close to the plasma. Two probe heads were positioned in different divertor pump gaps, top and bottom, and one close to the plasma on the midplane in one module. The gauges were in situ calibrated together with the ASDEX pressure gauges [G. Haas and H.-S. Bosch, Vacuum 51, 39 (1998)]. Data were taken during the entire operation phase 1.2b, and measurements were coherent with other neutral gas pressure gauges. For the spectroscopic partial pressure measurements, channels of a spectroscopic detection system based on photo-multipliers, a so-called filterscope [R. J. Colchin et al ., Rev. Sci. Instrum. 74, 2068 (2003)], provided by the Oak Ridge National Lab were used.
Oxygen partial pressure is an important thermodynamic state variable that affects both the performance and degradation of solid oxide electrolysis cells. In this work, a 3D model developed from Virkar’s 1D model has been applied to reconstructed and synthetic microstructures of Ni-YSZ-GDC-LSCF cell. The effect of the microstructures, including the thickness of the YSZ and GDC layer, and the compositions of the hydrogen and oxygen electrode, on the distribution of oxygen partial pressure has been investigated. The results show that the maximum oxygen partial pressure may occur on the interface between oxygen electrode and GDC layer or between GDC layer and YSZ layer depending on the rate of oxygen ion exchange between GDC and YSZ. A thicker GDC layer lowers the maximum oxygen partial pressure in the cell, while a thicker YSZ layer lowers the maximum oxygen partial pressure in the hydrogen electrode. In addition, the Ni:YSZ ratio and porosity also affects the maximum partial pressure. These findings provide insights on mitigating degradation in solid oxide electrolysis cell by tuning the microstructures.
The effect of O{sub 2} partial pressure on the mechanical properties of Al{sub 2}O{sub 3} films is studied. Using films prepared by inductively coupled plasma-assisted radio frequency magnetron sputtering, the deposition rate of Al{sub 2}O{sub 3} decreases rapidly when oxygen is added to the argon sputtering gas. The internal stresses in the films are compressive, with magnitude decreasing steeply from 1.6 GPa for films sputtered in pure argon gas to 0.5 GPa for films sputtered in argon gas at an O{sub 2} partial pressure of 0.89 Multiplication-Sign 10{sup -2} Pa. Stress increases gradually with increasing O{sub 2} partial pressure. Using a nanoindentation tester with a Berkovich indenter, film hardness was measured to be about 14 GPa for films sputtered in pure argon gas. Hardness decreases rapidly on the addition of O{sub 2} gas, but increases when the O{sub 2} partial pressure is increased. Adhesion, measured using a Vickers microhardness tester, increases with increasing O{sub 2} partial pressure. Electron probe microanalyzer measurements reveal that the argon content of films decreases with increasing O{sub 2} partial pressure, whereas the O to Al composition ratio increases from 1.15 for films sputtered in pure argon gas to 1.5 for films sputtered in argon gas at O{sub 2} partial pressures over 2.4 Multiplication-Sign 10{sup -2} Pa. X-ray diffraction measurements reveal that films sputtered in pure argon gas have an amorphous crystal structure, whereas {gamma}-Al{sub 2}O{sub 3} is produced for films sputtered in argon gas with added O{sub 2} gas. Atomic force microscopy observations reveal that the surface topography of sputtered Al{sub 2}O{sub 3} films changes from spherical to needlelike as O{sub 2} partial pressure is increased. Fracture cross sections of the films observed by scanning electron microscopy reveal that the film morphology exhibits no discernible features at all O{sub 2} partial pressures.
HyperCoal was produced from coal by a solvent extraction method. The effect of the partial pressure of steam on the gasification rate and gas composition at temperatures of 600, 650, 700, and 750{sup o}C was examined. The gasification rate decreased with decreasing steam partial pressure. The reaction order with respect to steam partial pressure was between 0.2 and 0.5. The activation energy for the K{sub 2}CO{sub 3}-catalyzed HyperCoal gasification was independent of the steam partial pressure and was about 108 kJ/mol. The gas composition changed with steam partial pressure and H{sub 2} and CO{sub 2} decreased and CO increased with decreasing steam partial pressure. By changing the partial pressure of the steam, the H{sub 2}/CO ratio of the synthesis gas can be controlled. 18 refs., 7 figs., 2 tabs.
γ-TiAl intermetallic alloys can be potentially employed as structural materials for many industries where high temperature and access of atmosphere with variable oxygen partial pressures are often met. Different partial pressures of oxygen may influence oxidation behavior and induce different oxide scale phase constitutes. This study investigated the influences of oxygen partial pressures on the oxidation resistance of a γ-TiAl alloy, Ti-46.7Al-1.9W-0.5Si (at.%), in Ar-O{sub 2} environments (5%O{sub 2}, 20%O{sub 2} and 80%O{sub 2}) at 750, 850 and 950 °C, respectively. The oxidation products were characterized using scanning electron microscopy, energy-dispersive x-ray analysis, x-ray diffraction and transmission electron microscopy. The oxidation kinetic results achieved by a discontinuous gravimetric method revealed that the alloy oxidized following a parabolic rate law. The oxidation resistance of the alloy was enhanced with increasing the oxygen partial pressures at all three experimental temperatures. Multilayered oxide scales of TiO{sub 2}/Al{sub 2}O{sub 3} were developed during the oxidation process. The enhancement of oxidation resistance was resulted from preferential generation of Al{sub 2}O{sub 3} and the reduction in defects in TiO{sub 2} with increasing the oxygen partials pressures.
Graphical abstract: - Highlights: • Microstructural and optical properties are studied systematically. • The optical properties are studied by UV–visible and photoluminescence. • The PL spectra shows two peaks correspond to bandgap of anatase and rutile. • The maximum refractive index of 2.73 is obtained for rutile phase of titania. - Abstract: Nanocrystalline titanium oxide (TiO{sub 2}) thin films were deposited on silicon (1 0 0) and quartz substrates at various oxygen partial pressures (1 × 10{sup −5} to 3.5 × 10{sup −1} mbar) with a substrate temperature of 973 K by pulsed laser deposition. The microstructural and optical properties were characterized using Grazing incidence X-ray diffraction, atomic force microscopy, UV–visible spectroscopy and photoluminescence. The X-ray diffraction studies indicated the formation of mixed phases (anatase and rutile) at higher oxygen partial pressures (3.5 × 10{sup −2} to 3.5 × 10{sup −1} mbar) and strong rutile phase at lower oxygen partial pressures (1 × 10{sup −5} to 3.5 × 10{sup −3} mbar). The atomic force microscopy studies showed the dense and uniform distribution of nanocrystallites. The root mean square surface roughness of the films increased with increasing oxygen partial pressures. The UV–visible studies showed that the bandgap of the films increased from 3.20 eV to 3.60 eV with the increase of oxygen partial pressures. The refractive index was found to decrease from 2.73 to 2.06 (at 550 nm) as the oxygen partial pressure increased from 1.5 × 10{sup −4} mbar to 3.5 × 10{sup −1} mbar. The photoluminescence peaks were fitted to Gaussian function and the bandgap was found to be in the range ∼3.28–3.40 eV for anatase and 2.98–3.13 eV for rutile phases with increasing oxygen partial pressure from 1 × 10{sup −5} to 3.5 × 10{sup −1} mbar.
In this work, the effect of the Xe partial pressure on the excimer vacuum ultraviolet (VUV) emission intensity of the plasma display panels is investigated, both by measuring the spectral emission directly and by two-dimensional simulations. Experimentally, we find that at the high Xe partial pressure levels, there is an supra-linear increase of excimer VUV radiation and that determines the strong increase of luminance at the high pressures and high voltage. Due to the increase of the luminance and the almost unchanged discharge current, the luminous efficacy strongly increases with the Xe partial pressure. In addition, we also investigated the dynamics of the VUV generation, by measuring the decay time of the excimer VUV light as a function of the gas pressure. It is found that the decay time decreases with the increase of gas pressure. The spatial characteristics of the excimer VUV emission are also discussed. Different from the Ne and near-infrared emission, the excimer VUV emission is generated near the surface of the electrodes and increases uniformly on both sides of the anode and cathode (i.e., the bulk plasma region). Most importantly, it is found that the VUV production occurs during the afterglow period, while it is almost zero at the moment of the discharge itself. From the simulations, it can be seen that the Xe{sub 2}*({sup 3}{Sigma}{sub u}{sup +}) excimer species, which are generated from Xe*(1s{sub 5}), play a dominant role in the excimer VUV emission output at the high Xe partial pressure. The two-dimensional simulations also show that the strong increase of Xe excimer excitation states in the case of high pressure is mainly the result of the high conversion efficiency of the Xe excimer states, especially in the afterglow period. Due to the high conversion efficiency of Xe excitation species to Xe excimer species by the high collision rate in the case of high pressure, there is a strong increase of excimer VUV production, especially from the cathode.
Thin films of zirconium oxide (ZrO{sub 2}) were deposited on (100) p-silicon and quartz substrates by sputtering of metallic zirconium target under different oxygen partial pressures in the range 8 Multiplication-Sign 10{sup -3}-6 Multiplication-Sign 10{sup -2}Pa. The effect of oxygen partial pressure on the structural and optical properties of the deposited films was systematically investigated. The deposition rate of the films decreased from 3.3 to 1.83 nm/min with the increase of oxygen partial pressure from 8 Multiplication-Sign 10{sup -3}-6 Multiplication-Sign 10{sup -2}Pa respectively. The X-ray diffraction profiles revealed that the films exhibit (111) refection of zirconium oxide in monoclinic phase. The optical band gap of the films increased from 5.62 to 5.80 eV and refractive index increased from 2.01 to 2.08 with the increase of oxygen partial pressure from 8 Multiplication-Sign 10{sup -3}-6 Multiplication-Sign 10{sup -2}Pa respectively.
Er-doped ZnO thin films have been prepared by using inductively coupled plasma enhanced physical vapor deposition at different O{sub 2}:Ar gas flow ratio (R = 0:30, 1:30, 1:15, 1:10 and 1:6). The influence of oxygen partial pressure on the structural, optical and magnetic properties was studied. It is found that an appropriate oxygen partial pressure (R=1:10) can produce the best crystalline quality with a maximum grain size. The internal strain, estimated by fitting the X-ray diffraction peaks, varied with oxygen partial pressure during growth. PL measurements show that plenty of defects, especially zinc vacancy, exist in Er-doped ZnO films. All the samples show room-temperature ferromagnetism. Importantly, the saturation magnetization exhibits similar dependency on oxygen partial pressure with the internal strain, which indicates that internal strain has an important effect on the magnetic properties of Er-doped ZnO thin films.
An approach to estimate the maximum hydrogen and oxygen partial pressures within sealed containers is described and applied to a set of packages containing high-purity plutonium dioxide. The approach uses experimentally determined maximum hydrogen and oxygen partial pressures and scales the experimentally determined pressures to the relevant packaged material properties. The important material properties are the specific wattage and specific surface area (SSA). Important results from the experimental determination of maximum partial pressures are (1) the ratio of hydrogen to oxygen is stoichiometric, and (2) the maximum pressures increase with increasing initial rates of production. The material properties that influence the rates are the material specific wattage and the SSA. The unusual properties of these materials, high specific wattage and high SSA, result in higher predicted maximum pressures than typical plutonium dioxide in storage. The pressures are well within the deflagration range for mixtures of hydrogen and oxygen.
There is an increasing interest in ensuring compatibility of existing natural gas infrastructure with conveyance of hydrogen, especially for vintage (pre-1970s) pipeline steels. While hydrogen is known to affect the fatigue and fracture resistance of these materials, there is a lack of data on its effects on crack initiation at low hydrogen partial pressure. To address this gap, the current work presents a series of fatigue tests on vintage API Grade X52 steel in pure nitrogen, air and gaseous hydrogen at partial pressures of 1 and 207 bar. Circumferential notch tension (CNT) specimens with direct current potential difference (DCPD) measurements are used to get S–N curves for crack initiation and failure, and compact tension (CT) tests to assess crack growth rates. Results indicate that air accelerates crack initiation, low hydrogen partial pressure affects the crack growth rate, and higher pressures have the largest impact on both. Surprisingly, crack initiation is faster in air than at 1 bar hydrogen partial pressure. The CNT tests also reveal that the orientation of the banded microstructure has no effect on the crack initiation site, but it influences its growth behavior. Moreover, fractography shows that hydrogen also promotes instances of quasi-cleavage and intergranular fracture, linked to embrittlement of the material. Here, these results demonstrate that, while hydrogen may impact the entirety of the fatigue process, its effects on the early stages of damage accumulation become relevant only at larger pressures. More comprehensive studies of crack initiation in hydrogen atmospheres will be critical to future codes and standards for hydrogen infrastructure.
In this work, the mechanism of the vacuum ultra-violet (VUV) emission of plasma discharges, with high Xe partial pressure and high ion-induced secondary electrons emission protective layer, is studied by measuring the VUV light emission directly and comparing it with two-dimensional simulations. From the panel measurement, we find that the high intensity of excimer VUV mainly contributes to the high luminous efficacy of SrCaO-plasma display panels (PDP) at a low sustain voltage. The unchanged Xe excitation efficiency indicates that the electron temperature is not decreased by the high secondary electrons emission protective layer, even though the sustain voltage is much lower. From the two-dimensional simulations, we can find that the ratio of excimer VUV to resonant VUV, which is determined by the collision rate in the discharge, is only significantly affected by the Xe partial pressure, while it is independent of the sustain voltage and the secondary-electrons-emission capability of protective layer. The unchanged average electron energy at the moment when the electric field becomes maximum confirms that the improvement of the VUV production efficiency mainly is attributed to the increase in electron heating efficiency of a PDP with high ion-induced secondary electrons emission protective layer. Combining the experimental and the simulation results, we conclude about the mechanism by which the VUV production is improved for the plasma display panel with a high Xe partial pressure and a cold cathode with high ion-induced secondary electrons emission.
Highlights: ► Fe doped and undoped TiO{sub 2} films are grown with varying oxygen partial pressure (OPP). ► Different structural and electrical phases of TiO{sub 2} films evolve with OPP. ► Phases obtained at different OPP are not same for films with different Fe doping. ► XPS confirms Fe is not in metal cluster form. ► Charge ordering is observed in magneli phase of Fe doped and undoped TiO{sub 2} films. -- Abstract: We have studied the influence of oxygen partial pressure (OPP; 250 mTorr–1 × 10{sup −5} Torr) and Fe doping (2 and 4 at.%) on structural and electrical properties of TiO{sub 2} thin films on LaAlO{sub 3} substrates. X-ray photoelectron spectroscopy suggests that Fe is not in metal cluster form. It is found that the evolution of the three phases; anatase, rutile and brookite of TiO{sub 2} as well as the magneli phase (Ti{sub n}O{sub 2n−1}) strongly depends on the OPP and Fe doping concentration. All the films grown at 250 mTorr show insulating behavior, whereas films grown at 1 × 10{sup −2} and 1 × 10{sup −4} Torr reveal high temperature metallic to low temperature semiconducting transition. Interestingly, films deposited at 1 × 10{sup −5} Torr reveal charge ordering, which is contributed to the magneli phase of TiO{sub 2}. The present study suggests that functionality of TiO{sub 2} thin film based devices can be tuned by properly selecting the OPP and dopant concentration.