Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Oxide Particles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Analysis of mid-tropospheric Space Shuttle exhausted aluminum oxide particles

Aluminum oxide particles from the exhaust of the Space Shuttle were collected immediately after the launch of the SEPEX mission and during the descent over the altitude interval of 7.6-4.6 km. The SEM examination revealed that the particles were spherical and ranged in diameter from about 0.1 micron to 10 microns. Results from the energy dispersive analysis (by an X-ray method) and of the particle chemistry (by electron spectroscopy) confirmed that the particles were predominantly composed of aluminum and oxygen. The particle size distribution of the Al2O3 was bimodal, with one observed peak centered near 2.0 microns; the other distribution mode centered at a diameter of less than 0.3 micron, but could not be accurately located. A mass median diameter was slightly less than 2 microns. Evaluation of ice nucleation activity revealed only a small fraction (about 1 ppm) of active ice nuclei among the Al2O3 particulates.

Cofer, Wesley R., III↗
NASA NTRS2000

Molecular Level Coating for Metal Oxide Particles

Polymer encapsulated metal oxide particles are prepared by combining a polyamide acid in a polar aprotic solvent with a metal alkoxide solution. The polymer was imidized and the metal oxide formed simultaneously in a refluxing organic solvent. The resulting polymer-metal oxide is an intimately mixed commingled blend, possessing synergistic properties of both the polymer and preceramic metal oxide. The encapsulated metal oxide particles have multiple uses including, being useful in the production of skin lubricating creams, weather resistant paints, as a filler for paper, making ultraviolet light stable filled printing ink, being extruded into fibers or ribbons, and coatings for fibers used in the production of composite structural panels.

McDaniel, Patricia R.↗
NASA NTRS2002

Molecular Level Coating of Metal Oxide Particles

Polymer encapsulated metal oxide particles are prepared by combining a polyamide acid in a polar osmotic solvent with a metal alkoxide solution. The polymer was imidized and the metal oxide formed simultaneously in a refluxing organic solvent. The resulting polymer-metal oxide is an intimately mixed commingled blend, possessing, synergistic properties of both the polymer and preceramic metal oxide. The encapsulated metal oxide particles have multiple uses including, being useful in the production of skin lubricating creams, weather resistant paints, as a filler for paper. making ultraviolet light stable filled printing ink, being extruded into fibers or ribbons, and coatings for fibers used in the production of composite structural panels.

Patricia R McDaniel↗
NASA NTRS2026

Influences of Introduced Yttrium Oxide Particles on Superalloy 718

Additive manufacturing has proven useful for introducing oxide particles into superalloys, to provide oxide dispersion strengthening (ODS) at high temperatures. This study screened how such an approach can influence microstructure and failure modes for superalloy 718. The objective of this study was to compare tensile and creep failure modes for additively manufactured superalloy 718 having introduced oxide particles. Fine yttrium-oxide (yttria) particles were introduced into 718 powder using two different powder mixing methods. Additive manufacturing by laser powder bed fusion was then used to prepare specimen blanks for each case, oriented parallel and transverse to the building direction. These were subsequently given consistent stress relief, hot isostatic pressurization, and final heat treatments, then subjected to tensile and creep tests at varied temperatures. Additively manufactured 718 without ODS (“no-ODS”) had nearly equiaxed grains at 50 μm in width. Roll-mixed ODS material had a bimodal grain size distribution, with fine grains at 9 μm and coarse grains at 66 μm in average width. The fine grains were elongated about 5x in the building direction. Acoustic-mixed ODS materials had grains at 10 μm in width that were elongated about 10x in the build direction. Compared to no-ODS, roll-mixed and acoustic mixed ODS materials did not show improved tensile strengths at room temperature, 760 °C, and 1093 °C. The tensile failure strains parallel to the building direction of roll-mixed ODS material were lowest in these tests. Flattened clumps of yttria had formed transverse to the building direction in roll-mixed material, which were easily cracked. Creep rupture response at 760 °C in the building direction was highest for acoustic-mixed material test. Creep tests at 1093 °C showed varied results, with low rupture lives associated with enhanced cavitation at grain boundaries and surface oxidation. Transverse to the building direction, all three materials had low failure strains in tests at 760 °C. The elongated grain boundaries failed readily in all transverse specimens tested at 760 °C and 1093 °C.

oxide dispersion strengthening↗
NASA NTRS1973

Observation of oxide particles below the apparent oxygen solubility limit in tantalum

The apparent solubility of oxygen in polycrystalline tantalum as determined by the X-ray diffraction lattice parameter technique is about 1.63 atomic percent at 820 C. However, oxide particles were identified in samples containing as low as 0.5 atomic percent of oxygen. These oxide particles were present at the grain boundaries and within the grains. The number of oxide particles increased with increasing oxygen concentration in tantalum. The presence of oxide particles suggests that the true solubility of oxygen in the polycrystalline tantalum metal is probably significantly lower than that reported in the literature.

Stecura, S.↗
NASA NTRS1974

Observation of oxide particles below the apparent oxygen solubility limit in tantalum

The apparent solubility of oxygen in polycrystalline tantalum as determined by the X-ray diffraction lattice parameter technique is about 1.63 at. pct at 820 C. However, oxide particles were identified in samples containing as low as 0.5 at. pct oxygen. These particles were present at the grain boundaries and within the grains. The number of oxide particles increased with increasing oxygen concentration in tantalum. The presence of oxide particles suggests that the true solubility in the polycrystalline tantalum metal is probably lower than that reported in the literature.

Stecura, S.↗
NASA NTRS1972

An experimental investigation of radiative properties of aluminum oxide particles.

The radiative properties of aluminum oxide at high temperatures were determined at various wavelengths. Absorption cross-sections of aluminum oxide particles averaged over a particle size distribution were determined by measuring the radiative emission from the particles in a flame and by determining the particle number density and size distribution from measurements of the scattering of laser light incident on the particles in this flame. From these values of average absorption cross-section, the imaginary part of the refractive index was deduced. Results indicate that the absorption cross-section and the imaginary part of the refractive index increase as the temperature increases in the range from 1920 to 2610 K, and that these properties decrease with increasing wavelength in the interval from 0.35 to 1.2 micron, indicating a nongray-body behavior.

Mularz, E. J.↗
NASA NTRS1957

A study of liquid boric oxide particle growth rates in a gas stream from a simulated jet engine combustor

It was experimentally determined that the liquid boric oxide particles leaving a jet engine combustor, burning a boron-containing fuel, will have diameters of 1.0 x 10(exp -5) to 2.0 x 10(exp -5) centimeter. For this size range the particle heat-transfer and drag coefficients are essentially infinite. The results may be applied to any boron-containing fuel. Equations are developed that enable the calculation of the particle size-time history. A study of boric oxide deposition mechanisms is included, and suggestions for decreading deposition rates given.

Setze, Paul C↗
NASA NTRS1989

Surface composition of solid-rocket exhausted aluminum oxide particles

Particulate samples of aluminum oxide were collected on Teflon filters from the exhaust plume of the Space Shuttle (STS-61A, October 30, 1985) over the altitude interval 4.6-7.6 km immediately after launch. These particles were analyzed using SEM, energy-dispersive X-ray analysis, electron spectroscopy for chemical analysis, X-ray fluorescent spectroscopy, and conventional wet-chemical techniques. The samples were 0.6-1.0 percent surface-chlorided (chlorided meaning predominantly aluminum chlorides and oxychlorides, possibly including other adsorbed forms of chloride) by weight. This level of chloriding is about one-third of the amount determined previously from laboratory-prepared alumina and surface site samples of solid-rocket-produced alumina (SRPA) after both had been exposed to moist HCl vapor at temperatures down to ambient. This level is equivalent to previous laboratory results with samples exposed to moist HCl at temperatures above the boiling point of water. It is suggested that the present lower chloriding levels, determined for samples from a 'dry' Shuttle exhaust cloud, underscore the importance of a liquid water/hydrochloric acid phase in governing the extent of surface chloriding of SRPA. The reduced chloriding is not trivial with respect to potential physical/chemical modification of the SRPA particle surfaces and their corresponding interaction with the atmosphere.

Cofer, Wesley R., III↗