Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Null Steering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Two-Channel Monopulse Antenna Null Steering

Traditional dual-channel phase-monopulse and amplitude-monopulse antenna systems might electrically steer their difference-channel nulls by suitably adjusting characteristics of their constituent beams or lobes. A phase-monopulse systems' null might be steered by applying suitable relative phase shifts. An amplitude-monopulse systems' null might be steered by applying a suitable relative beam amplitude scaling. The steering of the null might be employed by a continuously mechanically-scanning antenna to stabilize the null direction over a series of radar pulses.

42 ENGINEERING↗
NASA NTRS2018

Phased Array Antenna for the Mitigation of UAS Interference

The growing demand for Unmanned Aerial Systems (UAS) operating beyond the line of sight (BLOS) has resulted in an increased interest in using existing commercial satellite communication capabilities for UAS command and control (C2) communications. The World Radiocommunication Conference in 2015 designated portions of Ku-Band and Ka-Band fixed satellite service (FSS) spectrum to support UAS C2 communications, provided that potential interference with existing co-allocated users in these bands is addressed. As the user base in this new spectrum allocation expands, there is an increased potential for interference with existing terrestrial communication systems operating under fixed service (FS) allocations. The portion of Ka-Band spectrum allocated for UAS C2 avoids significant interference issues, but the Ku-Band allocation contains a co-primary FS allocation, creating potential interference problems. Therefore, UAS must identify solutions to avoid interfering with these existing FS ground sites while maintaining good links with satellite constellations. UAS operating with conventional fixed feed parabolic antennas will have difficulty in meeting interference thresholds, especially at high latitudes where the antennas will operate with low elevation angles. As a means of addressing this limitation, NASA is investigating the use of a phased array antenna to enable mitigation of interference into ground-based FS receivers. In this paper, a novel lightweight conformal phased array antenna will be presented that can use null-steering and/or beam shaping to avoid ground interference while simultaneously providing strong satellite microwave links for communications. The reduced weight of this design and ability to integrate into the fuselage of smaller UAS platforms will also be discussed as a potential solution to provide BLOS operation via spectrum sharing for an expanding user base. This paper will review design aspects of the conformal phased array antenna, describe the intended benefits in reducing interference with FS ground stations, and describe phased array development and test plans.

Phased Array↗
NASA NTRS2018

Phased Array Antenna for the Mitigation of UAS Interference

The growing demand for Unmanned Aerial Systems (UAS) operating beyond the line of sight (BLOS) has resulted in an increased interest in using existing commercial satellite communication capabilities for UAS command and control (C2) communications. The World Radiocommunication Conference in 2015 designated portions of Ku-Band and Ka-Band fixed satellite service (FSS) spectrum to support UAS C2 communications, provided that potential interference with existing co-allocated users in these bands is addressed. As the user base in this new spectrum allocation expands, there is an increased potential for interference with existing terrestrial communication systems operating under fixed service (FS) allocations. The portion of Ka-Band spectrum allocated for UAS C2 avoids significant interference issues, but the Ku-Band allocation contains a co-primary FS allocation, creating potential interference problems. Therefore, UAS must identify solutions to avoid interfering with these existing FS ground sites while maintaining good links with satellite constellations. UAS operating with conventional fixed feed parabolic antennas will have difficulty in meeting interference thresholds, especially at high latitudes where the antennas will operate with low elevation angles. As a means of addressing this limitation, NASA is investigating the use of a phased array antenna to enable mitigation of interference into ground-based FS receivers. In this paper, a novel lightweight conformal phased array antenna will be presented that can use null-steering and/or beam shaping to avoid ground interference while simultaneously providing strong satellite microwave links for communications. The reduced weight of this design and ability to integrate into the fuselage of smaller UAS platforms will also be discussed as a potential solution to provide BLOS operation via spectrum sharing for an expanding user base. This paper will review design aspects of the conformal phased array antenna, describe the intended benefits in reducing interference with FS ground stations, and describe phased array development and test plans.

Beam Forming↗
NASA NTRS2003

Comparison of TCeMA and TDMA for Inter-Satellite Communications using OPNET Simulation

A robust data link protocol, enabling unique physical and MAC layer technologies and sub-network level protocols, is needed in order to take advantage of the full potential of using both TDMA and CDMA in a satellite communication network. A novel MAC layer protocol, TDMA with CDMA-encoding multiple access (TCeMA) integrated with null-steered digital beam-forming spatial multiplexing, is investigated to support flexible spacecraft communications. Abstract models of the TCeMA and TDMA processes are developed in OPNFiT and a comparison of the performances of TCeMA and TDMA in a satellite network simulation are made. TCeMA provides the better connectivity and capacity with respect to TDMA for satellite communication traffic.

Hain, Regina Rosales↗
NASA NTRS2015

Signals of Opportunity Airborne Demonstrator (SoOP-AD)

In the second year of the SoOp-AD project, a brassboard analog section has been completed, along with working designs for the digital section and an antenna compatible with the NASA Langley B-200 or UC-12B aircraft. Resource requirements for the digital section FPGA are being finalized. One technical challenge at P-band is that the low transmitted data rate makes isolation of the direct and reflected signals using path delay, the conventional practice for GNSS reflectometry, difficult. Any retrieval of surface reflectivity from these measurements must account for the combination of direct and reflected signal in both the sky-view and Earth-view antennas. We have approached this challenge on several fronts; First, through null steering of the antenna. Second, through the formulation of an empirical calibration function for the reflectivity; and finally through estimating the direct and reflected signal powers as independent states in a Kalman filter. In addition to the direct-reflected interference from the same transmitter, there is also the possibility of interference due to transmissions, in adjacent bands, from other satellites in the constellation. Ground-based repeaters are also present in the S-band spectrum. Digital filters are being designed to isolate these repeaters, using simulations to verify the magnitude of their effect on the reflectivity and soil moisture retrievals. Other contributions to the error budget include the uncertainty in aircraft altitude, and the antenna pattern.

Radar↗
NASA NTRS2018

Phased Array Antenna for the Mitigation of UAS Interference

The growing demand for Unmanned Aerial Systems (UAS) operating beyond the line of sight (BLOS) has resulted in an increased interest in using existing commercial satellite communication capabilities for UAS command and control (C2) communications. The World Radiocommunication Conference in 2015 designated portions of Ku-Band and Ka-Band fixed satellite service (FSS) spectrum to support UAS C2 communications, provided that potential interference with existing co-allocated users in these bands is addressed. As the user base in this new spectrum allocation expands, there is an increased potential for interference with existing terrestrial communication systems operating under fixed service (FS) allocations. The portion of Ka-Band spectrum allocated for UAS C2 avoids significant interference issues, but the Ku-Band allocation contains a co-primary FS allocation, creating potential interference problems. Therefore, UAS must identify solutions to avoid interfering with these existing FS ground sites while maintaining good links with satellite constellations. UAS operating with conventional fixed feed parabolic antennas will have difficulty in meeting interference thresholds, especially at high latitudes where the antennas will operate with low elevation angles. As a means of addressing this limitation, NASA is investigating the use of a phased array antenna to enable mitigation of interference into ground-based FS receivers. In this paper, a novel lightweight conformal phased array antenna will be presented that can use null-steering and/or beam shaping to avoid ground interference while simultaneously providing strong satellite microwave links for communications. The reduced weight of this design and ability to integrate into the fuselage of smaller UAS platforms will also be discussed as a potential solution to provide BLOS operation via spectrum sharing for an expanding user base. This presentation will review design aspects of the conformal phased array antenna, describe the intended benefits in reducing interference with FS ground stations, and describe phased array development and test plans.

Conformal Phased Array↗
NASA NTRS2018

CLAS-ACT: Conformal, Lightweight Antennas for Aeronautical Communications Technology

The growing demand for Unmanned Aerial Vehicles (UAVs) and operating them beyond the line of sight (BLOS) has resulted in an increased interest in using existing satellite communication capabilities for command, control, and telemetry (CC&T). As the user base in this allocated portion of the spectrum expands, there is an increased potential for interference with existing terrestrial fixed-point communication systems. As secondary users, UAVs must seek out new solutions to avoid interfering with these existing ground sites while maintaining good links with satellite constellations. In this presentation, a novel lightweight conformal phased array antenna currently under development is presented that can use null steering and/or beam shaping to avoid ground interference while simultaneously providing strong satellite microwave links for communications. The reduced weight of this design and ability to integrate into the fuselage of smaller UAV platforms will also be discussed as a potential solution to provide BLOS operation via spectrum sharing for an expanding user base.

Meador, Mary Ann↗
NASA NTRS2019

Electromagnetic Modeling for the Conformal Lightweight Antenna System for Aeronautical Communications Technologies (CLAS-ACT) Program: Final Report

A series of electromagnetic simulations was conducted for the Conformal Lightweight Antenna System for Aeronautical Communications Technologies (CLAS-ACT) Program. The program designed, built, and flight tested a 14.25 GHz conformal patch array antenna for satellite communications on a T-34C airplane. Various studies were performed to evaluate the effects of antenna element spacing, array shape, signal taper, phased array pointing angle, null steering coefficients, antenna platform, and location on the airplane. This report documents the methods and some of the results of tests done over a 2 ½ year period.

Mackenzie, Anne I.↗
NASA NTRS2004

Digitally Synthesized Phased Antenna for Multibeam Global Positioning

In a system according to the proposed technique, the signal received by each element of the array antenna would be subjected to downconversion, and spread-spectrum demodulation and correlation as necessary; this processing would be performed separately from, and simultaneously with, similar processing of signals received by the other antenna elements. For the GPS implementation, following downconversion to baseband, the signals would be digitized, and all subsequent processing would be digital. In In the digital process, residual carriers would be removed and each signal would be correlated with a locally generated model pseudo random-noise code, all following normal GPS procedure. As part of this procedure, accumulated values would be added in software and the resulting signals would be phase-shifted in software by the amounts necessary to synthesize the desired antenna directional gain pattern of peaks and nulls. The principal advantage of this technique over the conventional radio-frequency-combining technique is that the parallel digital baseband processing of the signals from the various antenna elements would be a relatively inexpensive and flexible means for exploiting the inherent multiple-peak/multiple-null aiming capability of a phased-array antenna. In the original intended GPS application, the peaks and nulls could be directed independently for each GPS signal being tracked by the GPS receiver. This will improve the SNR simultaneously for each GPS signal being tracked while steering multiple nulls toward sources of interference. The technique could also be applied to other code-division multiple-access communication systems.

Charles E Dunn↗
NASA NTRS2004

Digitally synthesized phased antenna for multibeam global positioning

In a system according to the proposed technique (see figure), the signal received by each element of the array antenna would be subjected to downconversion, and spread-spectrum demodulation and correlation as necessary; this processing would be performed separately from, and simultaneously with, similar processing of signals received by the other antenna elements. For the GPS implementation, following downconversion to baseband, the signals would be digitized, and all subsequent processing would be digital. In the digital process, residual carriers would be removed and each signal would be correlated with a locally generated model pseudo random-noise code, all following normal GPS procedure. As part of this procedure, accumulated values would be added in software and the resulting signals would be phase-shifted in software by the amounts necessary to synthesize the desired antenna directional gain pattern of peaks and nulls. The principal advantage of this technique over the conventional radio-frequency-combining technique is that the parallel digital baseband processing of the signals from the various antenna elements would be a relatively inexpensive and flexible means for exploiting the inherent multiple-peak/multiple-null aiming capability of a phased-array antenna. In the original intended GPS application, the peaks and nulls could be directed independently for each GPS signal being tracked by the GPS receiver. This will improve the SNR simultaneously for each GPS signal being tracked while steering multiple nulls toward sources of interference. The technique could also be applied to other code-division multiple-access communication systems.

Dunn, Charles E.↗
NASA NTRS1987

Steering Law Design for Redundant Single Gimbal Control Moment Gyro Systems

The correspondence between robotic manipulators and single gimbal Control Moment Gyro (CMG) systems was exploited to aid in the understanding and design of single gimbal CMG Steering laws. A test for null motion near a singular CMG configuration was derived which is able to distinguish between escapable and unescapable singular states. Detailed analysis of the Jacobian matrix null-space was performed and results were used to develop and test a variety of single gimbal CMG steering laws. Computer simulations showed that all existing singularity avoidance methods are unable to avoid Elliptic internal singularities. A new null motion algorithm using the Moore-Penrose pseudoinverse, however, was shown by simulation to avoid Elliptic type singularities under certain conditions. The SR-inverse, with appropriate null motion was proposed as a general approach to singularity avoidance, because of its ability to avoid singularities through limited introduction of torque error. Simulation results confirmed the superior performance of this method compared to the other available and proposed pseudoinverse-based Steering laws.

Bedrossian, Nazareth Sarkis↗
NASA NTRS1991

Application of a directed search to global steering of single gimballed CMGs

A guided depth-first search that manages null motion about torque-producing trajectories calculated with a singularity-robust (SR) inverse is proposed as a practical feedforward steering law that can globally avoid (or minimize the impact of) singular states in minimally-redundant single gimballed CMG systems. Cost and heuristic functions are defined to guide the search procedure in improving CMG trajectories. On-orbit implementation of the steering law is proposed as an extension to momentum management algorithms. A set of simulation examples is presented, illustrating the search performance for a 4-CMG pyramid-mounted array. Sensitivities of feedforward gimbal trajectories are examined in the presence of unmodeled disturbances, and techniques are proposed for avoiding excessive divergence.

Paradiso, Joseph A.↗
NASA NTRS1990

Steering law design for redundant single-gimbal control moment gyroscopes

Two steering laws are presented for single-gimbal control moment gyroscopes. An approach using the Moore-Penrose pseudoinverse with a nondirectional null-motion algorithm is shown by example to avoid internal singularities for unidirectional torque commands, for which existing algorithms fail. Because this is still a tangent-based approach, however, singularity avoidance cannot be guaranteed. The singularity robust inverse is introduced as an alternative to the pseudoinverse for computing torque-producing gimbal rates near singular states. This approach, coupled with the nondirectional null algorithm, is shown by example to provide better steering law performance by allowing torque errors to be produced in the vicinity of singular states.

Bedrossian, Nazareth S.↗
NASA NTRS2019

Active Array Measurements using the Portable Laser Guided Robotic Metrology System

In this paper, we will discuss the impact of mounting structures on the installed performance of phased arrays. In particular, performance data for the Conformal, Lightweight Antennas for Aeronautical Communications Technology (CLAS-ACT) antenna will be presented. Performance data from a series of mounting configurations will show that null depth and location is particularly susceptible while the main beam steering angle remain relatively stable. In addition, the Portable Laser Guided Robotic antenna range (PLGR) will be discussed as a suitable instrument for measuring antenna patterns in complex or difficult locations that are challenging for traditional ranges. The PLGR antenna range was recently developed at the National Aeronautics and Space Administration's (NASA) Glenn Research Center (GRC) and deployed to measure in situ antenna patterns.

Piasecki, Marie↗
DOE OSTI2022

First Results from Diamagnetic Loop Measurements of the DARHT-I Electron Beam [Slides]

Diamagnetic-loop (DML) measurements can inform efforts to improve radiographic resolution. DML is non-invasive, so time-resolved data is available on every shot while tuning or executing a hydrotest. The time-resolved beam size can be deduced from the DML data. LIA beam-transport dynamics affecting beam size can be monitored while testing mitigation measures (e.g., beam halo suppression). Time-resolved beam size at final focus provides immediate information about spot size enlargement due to blur, and effectiveness of mitigation efforts. DML measures magnetic flux produced by a rotating beam, so it also enables monitoring of Larmor emittance that can enlarge the spot size. Beam rotation adds in quadrature with emittance, hence “Larmor emittance." Observing zero bias-field DML flux monitors beam rotation resulting from imperfect nulling of flux linking the cathode, and/or broken LIA transport symmetry (e.g., steering, quads, etc.).

43 PARTICLE ACCELERATORS↗
NASA NTRS2009

Balloon Exoplanet Nulling Interferometer (BENI)

We evaluate the feasibility of using a balloon-borne nulling interferometer to detect and characterize exosolar planets and debris disks. The existing instrument consists of a 3-telescope Fizeau imaging interferometer with 3 fast steering mirrors and 3 delay lines operating at 800 Hz for closed-loop control of wavefront errors and fine pointing. A compact visible nulling interferometer is under development which when coupled to the imaging interferometer would in-principle allow deep suppression of starlight. We have conducted atmospheric simulations of the environment above 100,000 feet and believe balloons are a feasible path forward towards detection and characterization of a limited set of exoplanets and their debris disks. Herein we will discuss the BENI instrument, the balloon environment and the feasibility of such as mission.

Lyon, Richard G.↗
NASA NTRS2011

Multi-Segment Radius Measurement Using an Absolute Distance Meter Through a Null Assembly

This system was one of the test methods considered for measuring the radius of curvature of one or more of the 18 segmented mirrors that form the 6.5 m diameter primary mirror (PM) of the James Webb Space Telescope (JWST). The assembled telescope will be tested at cryogenic temperatures in a 17-m diameter by 27-m high vacuum chamber at the Johnson Space Center. This system uses a Leica Absolute Distance Meter (ADM), at a wavelength of 780 nm, combined with beam-steering and beam-shaping optics to make a differential distance measurement between a ring mirror on the reflective null assembly and individual PM segments. The ADM is located inside the same Pressure-Tight Enclosure (PTE) that houses the test interferometer. The PTE maintains the ADM and interferometer at ambient temperature and pressure so that they are not directly exposed to the telescope s harsh cryogenic and vacuum environment. This system takes advantage of the existing achromatic objective and reflective null assembly used by the test interferometer to direct four ADM beamlets to four PM segments through an optical path that is coincident with the interferometer beam. A mask, positioned on a linear slide, contains an array of 1.25 mm diameter circular subapertures that map to each of the 18 PM segments as well as six positions around the ring mirror. A down-collimated 4 mm ADM beam simultaneously covers 4 adjacent PM segment beamlets and one ring mirror beamlet. The radius, or spacing, of all 18 segments can be measured with the addition of two orthogonally-oriented scanning pentaprisms used to steer the ADM beam to any one of six different sub-aperture configurations at the plane of the ring mirror. The interferometer beam, at a wavelength of 687 nm, and the ADM beamlets, at a wavelength of 780 nm, pass through the objective and null so that the rays are normally incident on the parabolic PM surface. After reflecting off the PM, both the ADM and interferometer beams return to their respective instruments on nearly the same path. A fifth beamlet, acting as a differential reference, reflects off a ring mirror attached to the objective and null and returns to the ADM. The spacings between the ring mirror, objective, and null are known through manufacturing tolerances as well as through an in situ null wavefront alignment of the interferometer test beam with a reflective hologram located near the caustic of the null. Since total path length between the ring mirror and PM segments is highly deterministic, any ADM-measured departures from the predicted path length can be attributed to either spacing error or radius error in the PM. It is estimated that the path length measurement between the ring mirror and a PM segment is accurate to better than 100 m. The unique features of this invention include the differential distance measuring capability and its integration into an existing cryogenic and vacuum compatible interferometric optical test.

Merle, Cormic↗
NASA NTRS2019

Active Array Measurements using the Portable Laser Guided Robotic Metrology System

In this paper, we will discuss the impact of mounting structures on the installed performance of phased arrays. In particular, performance data for the Conformal, Lightweight Antennas for Aeronautical Communications Technology (CLAS-ACT) antenna will be presented. Performance data from a series of mounting configurations will show that null depth and location is particularly susceptible to change while the main beam steering angle remains relatively stable. In addition, the Portable Laser Guided Robotic Metrology (PLGRM) system will be discussed as a suitable instrument for measuring antenna patterns in complex or difficult locations that are challenging for traditional ranges. The PLGRM system was recently developed at the National Aeronautics and Space Administration's (NASA) Glenn Research Center (GRC) and deployed to measure in situ antenna patterns.

Piasecki, Marie↗