Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NITROGEN OXIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Effects of Vegetation on Fluxes of Nitric Oxide, Nitrogen Dioxide, and Nitrous Oxide in a Mixed Deciduous Forest Clearing

Atmosphere-terrestrial exchange of nitrogen oxides, such as nitric oxide (NO), nitrogen dioxide (NO2) and nitrous oxide (N2O), plays an important role in controlling atmospheric composition and the radiative forcing of Earth’s atmosphere. In this study, the impact of vegetation ground cover on NOx (NOx = NO + NO2) and N2O fluxes in a deciduous forest clearing was studied using dynamic flow chambers located on three experimental plots with differing vegetation ground cover. Microbial emissions of NO and N2O were observed throughout the measurement period, while NO2 was exclusively deposited. Vegetation had no observable impact on NO2 deposition. Under dry conditions, total measured nitrogen emissions were numerically similar across all plots, although the N2O:NO ratio was higher for plots containing plants. Vegetation elevates soil water content through enhanced water retention, a condition that favors denitrification and more N2O production, relative to NO. Two rain events induced pulses of NO and N2O that were higher for bare soil compared to the vegetated plots. Lower NO and N2O emissions in plant-containing chambers stemmed from enhanced root uptake of N following rewetting, which diminished the amount of N substrate available for microbial NO and N2O production. The sensitivity of soil N emissions to vegetation ground cover highlights the need for more studies that investigate this effect over a wide range of ecosystems and to include vegetation effects in future parameterizations of soil NOx and N2O used in atmospheric models. This dataset includes processed data collected from 4 dynamic flux chambers and 17 sensors. Data includes ambient gas measurements made 1 m from the surface and soil flux measurements of NO, NO2, N2O, ozone (O3) and carbon dioxide (CO2). Also included is a suite of meteorological (air temperature, humidity, pressure) and soil parameters (water filled pore space, soil temperature). Refer to the readme for more information about each of the data sets.

54 ENVIRONMENTAL SCIENCES↗

A new method for inferring city emissions and lifetimes of nitrogen oxides from high-resolution nitrogen dioxide observations: a model study

We present a new method to infer emissions and lifetimes of nitrogen oxides (NO x ) based on tropospheric nitrogen dioxide (NO 2 ) observations together with reanalysis wind fields for cities located in polluted backgrounds. Since the accuracy of the method is difficult to assess due to lack of “true values” that can be used as a benchmark, we apply the method to synthetic NO 2 observations derived from the NASA-Unified Weather Research and Forecasting (NU-WRF) model at a high horizontal spatial resolution of 4 km × 4 km for cities over the continental United States. We compare the inferred emissions and lifetimes with the values given by the NU-WRF model to evaluate the method. The method is applicable to 26 US cities. The derived results are generally in good agreement with the values given by the model, with the relative differences of 2 % ± 17 % (mean ± standard deviation) and 15 % ± 25 % for lifetimes and emissions, respectively. Our investigation suggests that the use of wind data prior to the satellite overpass time improves the performance of the method. The correlation coefficients between inferred and NU-WRF lifetimes increase from 0.56 to 0.79 and for emissions increase from 0.88 to 0.96 when comparing results based on wind fields sampled simultaneously with satellite observations and averaged over 9 h data prior to satellite observations, respectively. We estimate that uncertainties in NO x lifetime and emissions arising from the method are approximately 15 % and 20 %, respectively, for typical (US) cities. The total uncertainties reach up to 43% (lifetimes) and 45% (emissions) by considering the additional uncertainties associated with satellite NO 2 observations and wind data. We expect this new method to be applicable to NO 2 observations from the TROPOspheric Monitoring Instrument (TROPOMI) and geostationary satellites, such as Geostationary Environment Monitoring Spectrometer (GEMS) or the Tropospheric Emissions: Monitoring Pollution (TEMPO) instrument, to estimate urban NO x emissions and lifetimes globally.

54 ENVIRONMENTAL SCIENCES↗

Copper Single Atom-Triggered Niobia–Ceria Catalyst for Efficient Low-Temperature Reduction of Nitrogen Oxides

To reduce nitrogen oxide (NO x ) emission from diesel engines in the cold-start process benefitting the atmospheric environment, catalysts with superior low-temperature NO x removal efficiency are highly demanded. Herein, we report an efficient Nb 2 O 5 /CuO/CeO 2 (NbCuCe) oxide catalyst for the selective catalytic reduction (SCR) of NO x , showing much higher DeNO x activity below 200 °C, superior sulfur resistance, faster response, and much less NH 3 slip than the state-of-the-art Cu-CHA zeolite catalyst. Additionally, atomically dispersed Cu species facilitate the strong interaction between Cu and the Nb/Ce base catalyst, which significantly improves the low-temperature redox properties at Cu–O–Ce sites and NH 3 adsorption/activation at Nb–O–Cu sites, thus contributing to the superior SCR performance of NbCuCe at low temperatures. The developed NbCuCe catalyst is highly promising for efficient DeNO x from cold-start diesel engines and can be coupled with Cu-CHA to achieve a broad operation temperature window.

36 MATERIALS SCIENCE↗

The impact of nitrogen oxides on electrochemical carbon dioxide reduction

The electroreduction of carbon dioxide offers a promising avenue to produce valuable fuels and chemicals using greenhouse gas carbon dioxide as the carbon feedstock. Because industrial carbon dioxide point sources often contain numerous contaminants, such as nitrogen oxides, understanding the potential impact of contaminants on carbon dioxide electrolysis is crucial for practical applications. Herein, we investigate the impact of various nitrogen oxides, including nitric oxide, nitrogen dioxide, and nitrous oxide, on carbon dioxide electroreduction on three model electrocatalysts (i.e., copper, silver, and tin). We demonstrate that the presence of nitrogen oxides (up to 0.83%) in the carbon dioxide feed leads to a considerable Faradaic efficiency loss in carbon dioxide electroreduction, which is caused by the preferential electroreduction of nitrogen oxides over carbon dioxide. The primary products of nitrogen oxides electroreduction include nitrous oxide, nitrogen, hydroxylamine, and ammonia. Despite the loss in Faradaic efficiency, the electrocatalysts exhibit similar carbon dioxide reduction performances once a pure carbon dioxide feed is restored, indicating a negligible long-term impact of nitrogen oxides on the catalytic properties of the model catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SCILLA nitrogen oxide (NOx) airborne data

Nitrogen oxides mixing ratios in ppb are measured using a Teledyne API Model T200UP. The analyzer uses chemiluminescence to determine NO concentration. Alternating measurement of the concentrations of total NOx (NO + NO2) and just NO are made by directing the sample through a blue light converter that photolyzes NO2 to NO and bypassing it, respectively, with the NO2 concentration calculated as the difference between the two. Sampled air was pulled from above the Naval Postgraduate School’s (NPS) Twin Otter aircraft through a rear-facing, ¼” OD PFA Teflon tube. The sample stream was split between several other gas analyzers (CO, O3, and H2O) and an oxidation flow reactor. The NO, NO2, and NOx mixing ratios were recorded once per minute.

NOx concentration↗

Nitrogen oxides storage catalysts containing cobalt

Nitrogen oxides (NO.sub.x) storage catalysts comprising cobalt and barium with a lean NO.sub.x storage ratio of 1.3 or greater. The NO.sub.x storage catalysts can be used to reduce NO.sub.x emissions from diesel or gas combustion engines by contacting the catalysts with the exhaust gas from the engines. The NO.sub.x storage catalysts can be one of the active components of a catalytic converter, which is used to treat exhaust gas from such engines.

Lauterbach, Jochen↗

Quorum Quenching of Nitrobacter winogradskyi Suggests that Quorum Sensing Regulates Fluxes of Nitrogen Oxide(s) during Nitrification

ABSTRACT Quorum sensing (QS) is a widespread process in bacteria used to coordinate gene expression with cell density, diffusion dynamics, and spatial distribution through the production of diffusible chemical signals. To date, most studies on QS have focused on model bacteria that are amenable to genetic manipulation and capable of high growth rates, but many environmentally important bacteria have been overlooked. For example, representatives of proteobacteria that participate in nitrification, the aerobic oxidation of ammonia to nitrate via nitrite, produce QS signals called acyl-homoserine lactones (AHLs). Nitrification emits nitrogen oxide gases (NO, NO 2 , and N 2 O), which are potentially hazardous compounds that contribute to global warming. Despite considerable interest in nitrification, the purpose of QS in the physiology/ecology of nitrifying bacteria is poorly understood. Through a quorum quenching approach, we investigated the role of QS in a well-studied AHL-producing nitrite oxidizer, Nitrobacter winogradskyi . We added a recombinant AiiA lactonase to N. winogradskyi cultures to degrade AHLs to prevent their accumulation and to induce a QS-negative phenotype and then used mRNA sequencing (mRNA-Seq) to identify putative QS-controlled genes. Our transcriptome analysis showed that expression of nirK and nirK cluster genes ( ncgABC ) increased up to 19.9-fold under QS-proficient conditions (minus active lactonase). These data led to us to query if QS influenced nitrogen oxide gas fluxes in N. winogradskyi . Production and consumption of NO x increased and production of N 2 O decreased under QS-proficient conditions. Quorum quenching transcriptome approaches have broad potential to identify QS-controlled genes and phenotypes in organisms that are not genetically tractable. IMPORTANCE Bacterial cell-cell signaling, or quorum sensing (QS), is a method of bacterial communication and gene regulation that is well studied in bacteria. However, little is known about the purpose of QS in many environmentally important bacteria. Here, we demonstrate quorum quenching coupled with mRNA-Seq to identify QS-controlled genes and phenotypes in Nitrobacter winogradskyi , a nitrite-oxidizing bacterium. Nitrite oxidizers play an important role in the nitrogen cycle though their participation in nitrification, the aerobic oxidation of ammonia to nitrate via nitrite. Our quorum quenching approach revealed that QS influences production and consumption of environmentally important nitrogen oxide gases (NO, NO 2 , and N 2 O) in N. winogradskyi . This study demonstrated a novel technique for studying QS in difficult-to-work-with microorganisms and showed that nitrite oxidizers might also contribute to nitrification-dependent production of nitrogen oxide gases that contribute to global warming.

Mellbye, Brett L.↗

Production of ozone and nitrogen oxides by laser filamentation

We have experimentally measured that laser filaments in air generate up to 10{sup 14}, 3x10{sup 12}, and 3x10{sup 13} molecules of O{sub 3}, NO, and NO{sub 2}, respectively. The corresponding local concentrations in the filament active volume are 10{sup 16}, 3x10{sup 14}, and 3x10{sup 15} cm{sup -3}, and allows efficient oxidative chemistry of nitrogen, resulting in concentrations of HNO{sub 3} in the parts per million range. The latter forming binary clusters with water, our results provide a plausible pathway for the efficient nucleation recently observed in laser filaments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Testing of an Integrated Nitrogen Oxide Catcher

A gas-purification system with maximum capacity 50 m{sup 3}/h was developed, fabricated, and tested to catch nitrogen oxides released during hydrometallurgical processing of spent fuel from the BREST reactor. To catch nitrogen oxides, the setup employs water aerosols introduced into the gas duct; it also includes a tank for mixing water aerosols with gas flow, coarse and fine filters, and BRUNS and SMOG apparatus. The filtering complex (mixing tank, FCGO and FAROS filters) gave 72–76% conversion of nitrogen dioxide with initial concentration of 11 g/m{sup 3}; this confirmed that aerosol fiberglass filters can be used to catch nitrogen dioxide. In the tests, the complex of units comprising the setup gave 95.4–98.5% conversion of nitrogen oxide with initial concentration 11–50 g/m{sup 3}. After the design of the mixing tanks is improved and remote extraction of the cartridges of the gas purification apparatus is organized, the tested gas purification setup can be used in radiochemical production.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Experimental Characterization of Hydrocarbons and Nitrogen Oxides Production in a Heavy-Duty Diesel–Natural Gas Reactivity-Controlled Compression Ignition Engine

Reactivity-Controlled Compression Ignition (RCCI) combustion is considered one of the most promising Low-Temperature Combustion (LTC) concepts aimed at reducing greenhouse gases for the transportation and power generation sectors. Due to the spontaneous combustion of a lean, nearly homogeneous mixture of air and low-reactivity fuel (LRF), ignited through the direct injection of a small quantity of high-reactivity fuel (HRF), RCCI (dual-fuel) shows higher efficiency and lower pollutants compared to conventional diesel combustion (CDC) if run at very advanced injection timing. Even though a HRF is used, the use of advanced injection timing leads to high ignition delays, compared to CDC, and generates high cycle-to-cycle variability, limited operating range, and high pressure rise rates at high loads. This work presents an experimental analysis performed on a heavy-duty single-cylinder compression ignited engine in dual-fuel diesel–natural gas mode. The objective of the present work is to investigate and highlight the correlations between combustion behavior and pollutant emissions, especially unburned hydrocarbons (HC) and oxides of nitrogen (NOx). Based on the analysis of crank-resolved pollutants measurements performed through fast FID and fast NOx systems under different engine operating conditions, two correlations were found demonstrating a good accordance between pollutant production and combustion behavior: Net Cyclic Hydrocarbon emission—cyclic IMEP variations (R 2 = 0.86), and Cyclic NOx—maximum value of the Rate of Heat Released (R 2 = 0.82).

33 ADVANCED PROPULSION SYSTEMS↗

High-resolution mapping of nitrogen oxide emissions in large US cities from TROPOMI retrievals of tropospheric nitrogen dioxide columns

Satellite-derived spatiotemporal patterns of nitrogen oxide (NOx) emissions can improve accuracy of emission inventories to better support air quality and climate research and policy studies. In this study, we develop a new method by coupling the chemical transport Model-Independent SATellite-derived Emission estimation Algorithm for Mixed-sources (MISATEAM) with a divergence method to map high-resolution NO x emissions across US cities using TROPOspheric Monitoring Instrument (TROPOMI) tropospheric nitrogen dioxide (NO 2 ) retrievals. The accuracy of the coupled method is validated through application to synthetic NO 2 observations from the NASA-Unified Weather Research and Forecasting (NU-WRF) model, with a horizontal spatial resolution of 4 km × 4 km for 33 large and mid-size US cities. Validation reveals excellent agreement between inferred and NU-WRF-provided emission magnitudes (R= 0.99, normalized mean bias, NMB = —0.01) and a consistent spatial pattern when comparing emissions for individual grid cells (R = 0.88 ± 0.06). We then develop a TROPOMI-based database reporting annual emissions for 39 US cities at a horizontal spatial resolution of 0.05° × 0.05° from 2018 to 2021. This database demonstrates a strong correlation (R= 0.90) with the National Emission Inventory (NEI) but reveals some bias (NMB = —0.24). There are noticeable differences in the spatial patterns of emissions in some cities. Our analysis suggests that uncertainties in TROPOMI-based emissions and potential misallocation of emissions and/or missing sources in bottom-up emission inventories both contribute to these differences.

54 ENVIRONMENTAL SCIENCES↗

Molecular Understanding of Nitrogen Oxide Fixation of Water-Lean Carbon Capture Solvents by Atomistic Modeling

Nitrogen oxides, present in flue gas, can cause negative impacts on amine carbon capture solvents by the formation of heat-stable salts and suspected carcinogens. Thus, to maximize the performance of water-lean solvents, a better understanding of this process in these systems is necessary. Here, a computational study for the fixation of the CO 2 capture solvent N-(2-ethoxyethyl)-3-morpholinopropan-1-amine (EEMPA) to nitramine/nitrosamine was conducted. The first step involves the dissociation of the NH bond of EEMPA, in which the homolytic mechanism is energetically more favorable than the heterolytic mechanism. The second step involves radical recombination to form N–N bonds. While NO 2 directly reacts with EEMPA, NO has almost no effect. However, in the presence of O 2 , fixation of EEMPA by NO is enhanced via the formation of N 2 O 4 species. Finally, low reaction energies indicate that the formation of nitramine/nitrosamine may be a reversible process, suggesting that EEMPA could be recovered under thermal stripping conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

System and method for controlling ammonia levels in a selective catalytic reduction catalyst using a nitrogen oxide sensor

A system according to the principles of the present disclosure includes an air/fuel ratio determination module and an emission level determination module. The air/fuel ratio determination module determines an air/fuel ratio based on input from an air/fuel ratio sensor positioned downstream from a three-way catalyst that is positioned upstream from a selective catalytic reduction (SCR) catalyst. The emission level determination module selects one of a predetermined value and an input based on the air/fuel ratio. The input is received from a nitrogen oxide sensor positioned downstream from the three-way catalyst. The emission level determination module determines an ammonia level based on the one of the predetermined value and the input received from the nitrogen oxide sensor.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In-Use Passenger Vessel Emission Rates of Black Carbon and Nitrogen Oxides

This study quantified emission factors of black carbon (BC) and nitrogen oxides (NO x ) from 21 engines on in-use excursion vessels and ferries operating in California's San Francisco Bay, including EPA uncertified and Tier 1-4 engines and across engine operating modes. On average, ~60 fuel-based emission factors per engine were measured using a novel combination of exhaust plume capture combined with GPS location and speed data that can be more readily deployed than common portable emissions measurement systems. Here, BC and NO x emission factors (g kg -1 ) were lowest and least variable during fast cruising and highest during maneuvering and docked operation. Selective catalytic reduction (SCR) reduced NO x emissions by ~80% when functional. However, elevated NO x emissions that exceeded corresponding exhaust standards were measured on most Tier 3 and Tier 4 engines sampled, which can be attributed to inactive SCR during frequent low engine load operation. In contrast, BC emissions exceeded the PM emission standard for only one engine, and SCR systems employed as a NO x reduction technology also reduced emitted BC. Using these measured emission factors to compare commuting options, we show that the CO 2 -equivalent emissions per passenger-kilometer are comparable when commuting by car and ferry, but BC and NO x emissions can be several to more than ten times larger when commuting by ferry.

54 ENVIRONMENTAL SCIENCES↗

Preliminary Evidence of Gas-Phase Water Splitting on Holmium Nitrogen Oxide Clusters

Preliminary Evidence of Gas-Phase Water Splitting on Holmium Nitrogen Oxide Clusters Christopher A. Zarzana1, Makayla R. Baxter , Introduction: Molecular hydrogen is a potential energy carrier that could be used to help implement a clean energy economy if it is generated from splitting of water. Improvements in the efficiencies of water-splitting electrolyzers relies on development of novel materials with enhanced performance. However, research in this area is slowed due to underdeveloped understanding of the mechanisms of device performance due to challenges interrogating the fundamental chemical reactions at play in bulk materials. Studies of the intrinsic reactivity of clusters that are representative of the reactive sites of these materials can increase understanding of the fundamental reaction mechanisms involved in hydrogen production, allowing for more efficient development of new water-splitting materials. Methods: Holmium tetranitrato ([Ho(NO3)4]-) clusters were generated in gas-phase using the electrospray ionization source of a Bruker (Billerica, MA, USA) micrOTOF-Q II quadrupole time-of-flight mass spectrometer. Spray solutions consisted of aqueous holmium (Ho) nitrate solutions (at nominally 3 mM) diluted to 30 µM in acetonitrile. The holmium (Ho) tetranitrato clusters were isolated using the quadrupole and were subsequently activated and allowed to react with background water in the collision cell. High resolution, high mass accuracy spectra were recorded using the time-of-flight. Mass accuracy was ensured using external calibration with Agilent (Santa Clara, CA, USA) ESI-L Low Concentration tuning mix. Preliminary data: Collisional activation of the holmium tetranitrato complexes ([Ln(NO3)4]-) resulted in an expected series of ions resulting from the loss of ·NO and ·NO2. This included an ion at m/z = 382.885 assigned as [HoO2(NO3)3]- (theoretical m/z=382.884, error=-1.2 ppm), resulting from loss of ·NO, and an ion at m/z=366.890 assigned as [HoO(NO3)3]- (theorical m/z=366.889, error=-1.8 ppm), resulting from loss of ·NO2. Additional ions were detected that would result from more complicated losses from [Ho(NO3)4]-, including ions at m/z=320.898 assigned as [HoO2(NO3)2]- (theoretical m/z=320.896, error=-4.9 ppm), at m/z=304.904 assigned as [HoO(NO3)2]- (theoretical m/z=304.901, error=-8.1 ppm, very low signal), and at m/z=288.908 assigned as [Ho(NO3)2]- (theoretical m/z=288.907, error=-3.4 ppm). This ion series would arise from loss of some combination of ·NO, ·NO2, and ·NO3, although it is not known whether these losses occur sequentially (e.g. loss of ·NO and ·NO3 to yield [HoO2(NO3)2]-) or as a single species (e.g. direct loss of N2O4). These ions were accompanied by a complementary series representing addition of a single water molecule. This included an ion at m/z=338.908 assigned as [HoO2(NO3)2H2O]- (theoretical m/z=338.907, error=-4.1 ppm), an ion at m/z=322.912 assigned as [HoO(NO3)2H2O]- (theoretical m/z=322.912, error=1.2 ppm), and an ion at m/z=306.918 assigned as [Ho(NO3)2H2O]-, (theoretical m/z=306.918, error=-3.7 ppm). An additional hydrated ion was observed at m/z=276.921 assigned as [HoO2(NO3) H2O]- (theoretical m/z=276.919, error=-7.3 ppm), although corresponding dehydrated ion was not observed. An additional ion was observed at m/z=367.898 that has been assigned as [Ho(NO3)3OH]- (theoretical m/z=367.897, error=-2.5 ppm). It is hypothesized that this ion arises from addition of water to [Ho(NO3)3]- followed by elimination of a hydrogen radical. Neither [Ho(NO3)3]- nor [Ho(NO3)3H2O]- were detected, suggesting that, if the hypothesis is correct, addition of water to [Ho(NO3)3]- and its subsequent splitting is rapid. Elimination of HNO3 from [Ho(NO3)4H2O]- could also yield [Ho(NO3)3OH]-; however, no [Ho(NO3)4H2O]- ions were observed. Novelty: Potential evidence of water splitting on gas-phase lanthanide clusters offers a way to study the intrinsic reactivity of hydrogen-generation materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Decarbonizing nitrogen fertilizer production via the electrochemical nitrogen oxidation reaction

Nitric acid is an important commodity chemical with extensive applications in both agricultural and industrial sectors. However, current production methods involve a combination of the Haber–Bosch and Ostwald processes, which are both energy and carbon emission intensive. The electrochemical nitrogen oxidation reaction (NOR) to produce nitric acid or nitrates shows great potential as an environmentally friendly method for producing fertilizers under mild conditions. The key to progress in this field lies in understanding the fundamental mechanistic insights and establishing robust experimental methods, which is essential for the efficient design and synthesis of electrocatalysts for NOR. Additionally, poor gas mass transport in conventional electrochemical reactors at present lead to lower NOR activity, thereby limiting the progress in this field. In this work, we present a synergistic computational and experimental approach to map out the potential chemical and electrochemical steps and determine the energetics on PtO 2 catalyst to gain mechanistic insights into NOR. Here, this study marks the first attempt to perform NOR in a vapor-fed reactor designed using advanced (additive) manufacturing. The vapor-fed reactor significantly improved the N 2 mass transport to the catalyst, allowing us to report the highest rate for nitrate production to date at 3.3 μmol cm -2 h -1 at 2.01 V vs RHE.

30 DIRECT ENERGY CONVERSION↗