SEARCH · Engineering Papers
Results for “Microstructural viscosity”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effect of CMAS viscosity on the infiltration depth in thermal barrier coatings of different microstructures
Calcium magnesium aluminum silicate (CMAS) is one of the leading concerns for the gas turbine industry. The effects of CMAS viscosity and the coating microstructure on CMAS infiltration depth were explored by conducting a time dependent interaction study. Three CMAS compositions were used from literature, and their viscosities predicted through FactSage viscosity module were drastically different. The interaction was carried out on three different TBCs synthesized using the solution precursor plasma spray process (SPPS): two of the TBCs were made of yttrium aluminum garnet (YAG) having different microstructures that promote different modes of CMAS infiltration, and one TBC was made of gadolinium zirconate (GZO). All samples had stress relieving vertical cracks and different intensities of horizontally banded porosity, (inter pass boundaries IPBs). A concentration of 100 mg/cm 2 of CMAS was applied on the TBCs which were then subjected to a 5-minute interaction at 1300 °C. Samples were analyzed using scanning electron microscopy (SEM), electron dispersive X-ray spectroscopy (EDXS), and transmission electron microscopy (TEM). Low viscosity CMAS readily penetrated the TBCs while more viscous CMAS showed less penetration. The depth of CMAS infiltration depended on the coating microstructure. In the YAG with IPBs, the CMAS spread horizontally in the IPBs before infiltrating deeper, resulting in reduced infiltration depth compared to other samples in spite of having wider vertical cracks. TEM and EDXS analysis were performed to investigate the phases present in the CMAS-TBC interaction region in YAG. Two regions were chosen, the top TBC surface in direct contact with the sea of CMAS, and the region at the CMAS penetration ended within the coating. Finally, the results showed that no secondary phases like apatite were observed in YAG, thus it can be concluded that the arrest of CMAS happened solely because of CMAS viscosity and the short infiltration time.
Containment strategy for subsurface H 2 storage based on time-dependent soft solids
Here, we propose an innovative containment strategy based on time-dependent soft solids, namely 2 wt% Laponite suspensions, to reinforce natural subsurface seals and engineer flow barriers, with an eye toward making H 2 subsurface storage scalable and geographically agnostic. This suspension can be injected at its initial low viscosity and elasticity into a porous medium, allowing for easy pumping and targeted delivery. Once inside the target zone, it matures into a soft solid with much higher viscosity and elasticity, acting as a potential flow barrier. We discuss the rheological properties of the suspensions and demonstrate that hydrogen does not adversely affect their microstructure, but rather increases the suspensions’ viscosity and elasticity. Moreover, the suspensions enhance the rock samples’ compressive strength, while hydrogen exposure increases their stiffness and ductility. The ability of rock samples saturated with the suspensions to contain higher injected gas pressures is enhanced by aging at higher temperatures.
Reliability of Materials and Components for Solid Oxide Fuel Cells
Planar stack solid-oxide fuel cells (SOFCs) require seals that must operate reliably under demanding conditions for lifetimes of 40000 hours. This includes temperature fluctuations between 800°C and RT during on and off cycles, thermal stresses, oxidizing environments and chemical degradation to name a few. This comprehensive report provides results from long term testing of two commercially available multicomponent barium alkali silicate glasses: SCN and G6, chosen as sealing candidates. In this scope, the glass seals were deposited on YSZ and Al 2 O 3 substrates simulating electrolytes (Zrbased) and coatings (both zirconia and Al 2 O 3 ). The seal-substrate couples were subjected to 800°C under air and steam+H 2 +N 2 environments up to 40000 hours to test their integrity under real operating conditions. Extensive studies on the effects of exposure have been conducted over the span of testing at various time intervals. Within the context of characterization, mechanical properties such as density, roughness, thermal expansion and glass transition, viscosity and wettability behavior; and microstructural properties such as glass chemistries, defect formation (cracks and pores), phase transformations (devitrification) and glass-interface reactions are investigated. Results and discussions are provided with a focus on the degradation of the properties over long term interrupted testing.
Coarsening dynamics of ternary polymer solutions with mobility and viscosity contrasts
Using phase-field simulations, we investigate the bulk coarsening dynamics of ternary polymer solutions undergoing a glass transition for two models of phase separation: diffusion only and with hydrodynamics. The glass transition is incorporated in both models by imposing mobility and viscosity contrasts between the polymer-rich and polymer-poor phases of the evolving microstructure. For microstructures composed of polymer-poor clusters in a polymer-rich matrix, the mobility and viscosity contrasts significantly hinder coarsening, effectively leading to structural arrest. For microstructures composed of polymer-rich clusters in a polymer-poor matrix, the mobility and viscosity contrasts do not impede domain growth; rather, they change the transient concentration of the polymer-rich phase, altering the shape of the discrete domains. This effect introduces several complexities to the coarsening process, including percolation inversion of the polymer-rich and polymer-poor phases—a phenomenon normally attributed to viscoelastic phase separation.
Effect of Microstructure on Chain Flexibility and Glass Transition Temperature of Polybenzofulvene
Polybenzofulvene (PBF) is a polydiene with a very high glass transition temperature (T g ), which makes it a potential candidate for use as the hard block for high-temperature thermoplastic elastomer applications. The T g s of polydienes are known to be related to chain flexibility. However, no studies have been reported that correlate the chain flexibility to the microstructure of PBF. Herein, we present a study of solution properties of linear PBFs with narrow molecular weight dispersity and having 1,2-addition ranging from 23% to 99%. The materials were prepared by living anionic polymerization under different conditions. Specifically, the chain flexibility as defined by the Flory's characteristic ratio, , and dependence of chain flexibility on microstructure by combined measurements of intrinsic viscosity and molecular weight using triple-detector size exclusion chromatography (SEC) is studied. The persistence lengths (l p ) and chain diameters (d B ) were also estimated using the touched-bead wormlike chain model. To the best of our knowledge, the characteristic ratio of PBF is found to be the highest of all polydienes that have been reported so far.
Morphological controls on flow conductivity and viscosity of bentonite–polymer composites
In this study, the authors investigate the morphological organisation of polymers in bentonite–polymer composites (BPCs) used in geosynthetic clay liners and controls on hydraulic conductivity and viscosity. A limited understanding of the relationship between the microstructure of BPCs and their macroscopic engineering behaviour motivates this study. The polymer resides in the inter-granular pores of bentonite based on synchrotron-based small-angle X-ray scattering measurements, scanning electron microscopy imaging and pore size analyses. On wetting, the polymer swells to produce a swollen hydrogel residing in the inter-granular pores. Enhanced tortuosity arising from hydrogel formation reduces the hydraulic conductivity of BPCs. The higher viscosity of the BPC slurry is attributed to the higher shear resistance emerging from swelling of the polymer fraction on wetting. These findings link the morphological features of BPCs to the observed hydraulic conductivity and viscosity of these materials.
Connecting particle interactions to agglomerate morphology and rheology of boehmite nanocrystal suspensions
Rheology imposes significant challenges on processing of complex suspensions such as nuclear waste slurries at the Hanford and Savannah River sites. Understanding rheology connecting to microstructures and underlying particle interactions in complex slurries is therefore important for both fundamental knowledge and practical applications. Here, we use suspensions of aluminum oxyhydroxide minerals in the form of boehmite as an analog of the radioactive waste slurry to gain physical insights on the correlation between particle interactions, microstructures, and slurry rheology. Specifically, we use a combination of Couette rheometry and small-angle scattering techniques (independently and simultaneously) to understand how the slurry microstructure changes under flow and how these structural changes manifest themselves in the bulk rheology of the suspensions. Our experiments show that the boehmite slurries are thixotropic, with the rheology and structure of the suspensions changing with increasing exposure to flow. In the slurries, particle aggregates begin as loose, system-spanning clusters, but exposure to moderate shear rates causes the aggregates to irreversibly consolidate into denser clusters of finite size. The microstructural changes directly influence the rheological properties of the slurries such as viscosity and viscoelasticity. More importantly, our study shows that solution pH affects the amount of structural rearrangement and the kinetics of the rearrangement process, with an increase in pH leading to faster and more dramatic changes in the bulk rheology. Such dynamic microstructural changes and resultant rheology are understood via correlations between particle interactions and strength of particle network, coupled with surface chemistry and anisotropic nature of particle interactions. Nearly identical structural changes are also observed in Poiseuille flow geometries, implying that the observed changes are relevant in the pipe flow conditions present during waste processing.
Evaluating the Rheo-electric Performance of Aqueous Suspensions of Oxidized Carbon Black
Here, the macroscopic properties of carbon black suspensions are primarily determined by the agglomerate microstructure built of primary aggregates. Conferring colloidal stability in aqueous carbon black suspensions should thus have a drastic impact on their viscosity and conductivity. Carbon black was treated with strong acids following a wet oxidation procedure. An analysis of the resulting particle surface chemistry and electrophoretic mobility was performed in evaluating colloidal stability. Changes in suspension microstructure due to oxidation were observed using small-angle X-ray scattering. Utilizing rheo-electric measurements, the evolution of the viscosity and conductivity of the carbon black suspensions as a function of shear rate and carbon content was thoroughly studied. The carboxyl groups installed on the carbon black surface through oxidation increased the surface charge density and enhanced repulsive interactions. Electrostatic stability inhibited the formation of the large-scale agglomerates in favor of the stable primary aggregates in suspension. While shear thinning, suspension conductivities were found to be weakly dependent on the shear intensity regardless of the carbon content. Most importantly, aqueous carbon black suspensions formulated from electrostatically repulsive primary aggregates displayed a smaller rise in conductivity with carbon content compared to those formulated from attractive agglomerates.
Atmospheric plasma spraying to fabricate metal‐supported solid oxide fuel cells with open‐channel porous metal support
Abstract Metal‐supported solid oxide fuel cells (MS‐SOFCs) have been fabricated by applying phase‐inversion tape‐casting and atmospheric plasma spraying (APS). The effect of the binder amount of the phase‐inversion slurries on the microstructure development of the 430L stainless steel metal support was investigated. The pore structures, the viscosity of the slurry, porosity and permeability of the as‐prepared metal supports are significantly influenced by the amount of the binder. NiO–scandia‐stabilized zirconia (ScSZ) anode, ScSZ electrolyte and La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3−δ (LSCF) cathode layers were consecutively deposited on the metal support with an ideal microstructure by APS process. The effect of plasma power of the APS on the microstructure of the electrolyte and cathode was investigated. A dense electrolyte layer and a porous cathode layer were successfully obtained at 40 and 6 kW of the APS plasma power, respectively. MS‐SOFCs, with a cell configuration of 430L/Ni‐ScSZ/ScSZ/LSCF, achieved a maximum cell power density of 1079 mW cm −2 at 700°C using humidified H 2 as fuel and ambient air as oxidant. The corresponding ohmic resistance and total resistance of MS‐SOFCs was 0.14 and 0.32 Ω cm 2 , respectively. This work demonstrates the feasibility of fabricating high‐performance MS‐SOFCs with economical and scalable techniques.
Block Polyelectrolyte Additives That Modulate the Viscoelasticity and Enhance the Printability of Gelatin Inks at Physiological Temperatures
We demonstrate the utility of block polyelectrolyte (bPE) additives to enhance viscosity and resolve challenges with the three-dimensional (3D) printability of extrusion-based biopolymer inks. The addition of oppositely charged bPEs to solutions of photocurable gelatin methacryloyl (GelMA) results in complexation-driven self-assembly of the bPEs, leading to GelMA/bPE inks that are printable at physiological temperatures, representing stark improvements over GelMA inks that suffer from low viscosity at 37 °C, leading to low printability and poor structural stability. The hierarchical microstructure of the self-assemblies (either jammed micelles or 3D networks) formed by the oppositely charged bPEs, confirmed by small-angle X-ray scattering, is attributed to the enhancements in the shear strength and printability of the GelMA/bPE inks. Varying bPE concentration in the inks is shown to enable tunability of the rheological properties to meet the criteria of pre- and postextrusion flow characteristics for 3D printing, including prominent yielding behavior, strong shear thinning, and rapid recovery upon flow cessation. Moreover, the bPE self-assemblies also contribute to the robustness of the photo-cross-linked hydrogels; photo-cross-linked GelMA/bPE hydrogels are shown to exhibit higher shear strength than photo-cross-linked GelMA hydrogels. Last, the assessment of the printability of GelMA/bPE inks indicates excellent printing performance, including minimal swelling postextrusion, satisfactory retention of the filament shape upon deposition, and satisfactory shape fidelity of the various printed constructs. We envision this study to serve as a practical guide for the printing of bespoke extrusion inks where bPEs are used as scaffolds and viscosity enhancers that can be emulated in a range of photocurable precursors.
Quantifying electron transport in aggregated colloidal suspensions in the strong flow regime
Electron transport in complex fluids, biology, and soft matter is a valuable characteristic in processes ranging from redox reactions to electrochemical energy storage. These processes often employ conductor–insulator composites in which electron transport properties are fundamentally linked to the microstructure and dynamics of the conductive phase. While microstructure and dynamics are well recognized as key determinants of the electrical properties, a unified description of their effect has yet to be determined, especially under flowing conditions. In this work, the conductivity and shear viscosity are measured for conductive colloidal suspensions to build a unified description by exploiting both recent quantification of the effect of flow-induced dynamics on electron transport and well-established relationships between electrical properties, microstructure, and flow. These model suspensions consist of conductive carbon black (CB) particles dispersed in fluids of varying viscosities and dielectric constants. In a stable, well-characterized shear rate regime where all suspensions undergo self-similar agglomerate breakup, competing relationships between conductivity and shear rate were observed. To account for the role of variable agglomerate size, equivalent microstructural states were identified using a dimensionless fluid Mason number, Mn f , which allowed for isolation of the role of dynamics on the flow-induced electron transport rate. At equivalent microstructural states, shear-enhanced particle–particle collisions are found to dominate the electron transport rate. This work rationalizes seemingly contradictory experimental observations in literature concerning the shear-dependent electrical properties of CB suspensions and can be extended to other flowing composite systems.
In situ deformation of antigorite-olivine two-phase mixtures: Implications for dynamics and seismic anisotropy in the mantle wedge
Water released from hydrous minerals in subducting slabs reacts with the overlying plate, resulting in widespread serpentinization in the mantle wedge. Deformation of serpentinized peridotites has been invoked to explain forearc seismic anisotropy, yet studies of the mechanical properties and deformation behaviors of serpentine-bearing multiphase aggregates remain limited. Here we deformed olivine-antigorite mixtures containing 70, 50, and 20 vol.% of antigorite at 2.5 – 7.6 GPa, 673 K and strain rates of ∼10 –5 –10 –4 s –1 . Elasto-viscoplastic self-consistent simulations, constrained by synchrotron X-ray diffraction (XRD) data, were used to estimate lattice strain, stress–strain partitioning, crystallographic preferred orientations (CPO) development, and aggregate strength. Selected run products were also analyzed by electron backscatter diffraction for comparison with the CPO results obtained from XRD experiments. We found olivine transitions from A- or B-type to C-type when antigorite fraction drops to 20 vol.%, coinciding with a microstructural change from interconnected weak layers to a load-bearing framework (LBF). An additional run on a sample Atg50/Ol50 with preexisting microstructures suggested the formation of LBF was promoted by these microstructures, although the preexisting antigorite CPO has been overprinted at 20.8 % strain and could be erased completely by subsequent deformation in nature. Estimated viscosity of the two-phase mixtures suggests that low-degree serpentinization (≤20 %) in the mantle wedge may increase the strength of olivine-rich peridotite and hinder slab-mantle decoupling, whereas high-degree serpentinization (≥50–70 %) weakens the peridotite and favors decoupling if sufficient viscosity contrast (>10) develops. Seismic anisotropy shows a nonlinear dependence on antigorite fraction: antigorite CPO governs the anisotropy of the mixtures with ≥50 vol.% antigorite, whereas olivine CPO dominates at low fractions (∼20 vol.%). The presence of pre-existing microstructures reduces seismic anisotropy of the deformed mixtures, however the persistence of pre-existing CPO in actively subducting slabs remains uncertain, making their significance over geological timescales questionable.
Dynamic strength of iron under pressure-temperature conditions of Earth’s inner core
Iron (Fe) is a primary constituent of terrestrial planetary cores, yet its rheological properties under extreme conditions remain uncertain. Here we present direct measurements of Fe strength at 310-430 GPa pressures and 3700-5800 K temperatures, obtained using Rayleigh-Taylor (RT) instability experiments at the National Ignition Facility. Single-crystal α-Fe samples with [001] and [111] orientations are shock-ramp compressed past the α-ε transition along paths approaching Earth’s inner core conditions. We find that ε-Fe derived from [001] α-Fe is consistently stronger (11-20 GPa) than that from [111] α-Fe (8-18 GPa), contrary to the trend at ambient conditions. Large-scale molecular dynamics simulations reproduce this atypical strength anisotropy and attribute it to microstructural evolution during the phase transition and subsequent ε-phase plasticity. Ripple growth analysis further constrains viscosities of 100-170 Pa·s under the driven conditions. Our results provide experimental benchmarks for Fe rheology at inner-core conditions, with implications for seismic anisotropy and the geodynamo.
Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes
A major factor driving fuel cell costs is the quantity of precious metal required. Therefore, it is important to understand a timeframe where inks can be reused. Here, in this work, we explore differences between a freshly prepared catalyst ink and one that has been stored for over a year – comparing ink properties, cathode catalyst layer microstructure, and their respective fuel cell performance. Ink studies revealed smaller agglomerate sizes and a decrease in shear viscosity for the aged ink. Longer storage time also results in fewer cracks and a more uniform ionomer distribution, as evidenced by microscopy characterization of rod-coated electrodes. Lastly, polarization curves show improved performance at higher current densities for the electrode prepared from the aged ink. We rationalize such effect in terms of enhanced ionomer adsorption onto the catalyst over time.
Material processing, microstructure, and composite properties of low carbon Engineered Cementitious Composites (ECC)
Traditional PVA fiber-reinforced Engineered Cementitious Composites (ECC) show high tensile ductility and superior durability with tight crack width, but the high cost and embodied carbon can hinder its wider application in infrastructures. The objective of this study is to develop a better understanding of the fresh and hardened properties of an ECC that employs a lower embodied-carbon binder, Limestone Calcined Clay Cement (LC3), and lower-cost PP fiber that is widely available. Specifically, the interrelations between material processing, microstructure, and composite properties were studied experimentally. The results showed that ECC with high tensile ductility up to 9% tensile strain and tight crack width with 50 μm at 2% tensile strain can be achieved. It was found that a matrix paste with higher viscosity generally enhanced fiber dispersion uniformity and robustness in tensile strain-hardening. The paste viscosity is increased when OPC is replaced by LC3 and can be tuned with superplasticizer content. Larger maximum flaw size leads to lower first crack strength, beneficial for microcrack initiation and multiple cracking. This study generates fundamental knowledge linking processing-microstructure-performance of PP-LC3-ECC. This class of low embodied carbon ECC with tight crack width is expected to contribute to reducing the carbon footprint of the built environment.
Rheological dynamics and structural characteristics of supramolecular assemblies of β-cyclodextrin and sulfonic surfactants
Cyclodextrins are highly functional compounds with a hydrophobic cavity capable of forming supramolecular inclusion complexes with various classes of molecules including surfactants. The resultant rich nanostructures and their dynamics are an interesting research problem in the area of soft condensed matter and related applications. In this paper, we report novel dynamical supramolecular assemblies based on the complexation of β-cyclodextrin with 3 different sulfonic surfactants, which are sodium hexadecylsulfate, sodium dodecylbenzenesulfonate, and myristyl sulfobetaine. It was observed that a β-cyclodextrin : surfactant/2 : 1 molar ratio was ideal for inducing axial growth and imparting large viscosities in the suspensions. Such complexation processes were accompanied by intriguing nanostructural phase behaviors and rheological properties that were very sensitive to the molecular architecture of sulfonic surfactants. The presence of an amino group in the head group of the surfactant allowed for large viscosities that reached 2.4 × 10 4 Pa s which exhibited gel-like behavior. In contrast, smaller viscosity values with a lower consistency index were observed when a bulky aromatic ring was present instead. DIC microscopy was used to visually probe the microstructure of the systems with respect to sulfonate molecular architecture. Additionally, surface tension measurements, and FTIR and NMR spectroscopies were used to gain insights into the nature of interactions that lead to the complexation and nanostructural characteristics. Finally, mechanics correlating the supramolecular morphologies to the rheological properties were proposed.
Rheo-electric measurements of carbon black suspensions containing polyvinylidene difluoride in N -methyl-2-pyrrolidone
Lithium-ion battery cathode slurries have a microstructure that depends sensitively on how they are processed due to carbon black's (CB) evolving structure when subjected coating flows. While polyvinylidene difluoride (PVDF), one of the main components of the cathode slurry, plays an important role in modifying the structure and rheology of CB, a quantitative understanding is lacking. In this work, we explore the role of PVDF in determining the structural evolution of Super C65 CB in N-methyl-2-pyrrolidinone (NMP) with rheo-electric measurements. We find that PVDF enhances the viscosity of NMP resulting in a more extensive structural erosion of CB agglomerates with increasing polymer concentration and molecular weight. We also show that the relative viscosity of all suspensions can be collapsed by the fluid Mason number (Mnf), which compares the hydrodynamic forces imposed by the medium to cohesive forces holding CB agglomerates together. Using simultaneous rheo-electric measurements, we find at high Mnf, the dielectric strength (Δε) scales with Mnf, and the power-law scaling can be quantitatively predicted by considering the self-similar break up of CB agglomerates. The collapse of the relative viscosity and scaling of Δε both suggest that PVDF increases the hydrodynamic force of the suspending medium without directly changing the CB agglomerate structure. These findings are valuable for optimizing the rheology of lithium ion battery cathode slurries. We also anticipate that these findings can be extended to understand the microstructure of similar systems under flow.