Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MFI”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

Design and Test of Mixed-flow Impellers III : Design and Experimental Results for Impeller Model MFI-2A and Comparison with Impeller Model MFI-1A

A mixed-flow impeller was designed to give a prescribed blade-surface velocity distribution at mean blade height for a given hub-shroud profile. The blade shape at mean blade height, which was produced by the prescribed velocity distribution, was extended by means of radial lines to form the composite blade shape from hub to shroud. The resulting blade was relatively thick; therefore, it was necessary to retain the inverse blade taper which resulted from extension of the radial lines in order to prevent merging or near merging of the separate blades near the hub. For the first test version of the impeller, designated the MFI-2A, the blade height was arbitrarily made greater than that for the basic impeller (the MFI-2) to allow for viscous effects. At design equivalent speed of 1400 feet per second the peak pressure ratio and maximum adiabatic efficiency were 3.95 and 79 percent, respectively. The adiabatic efficiency of the MFI-2A is four points lower than that for impeller model MFI-1A, but because of the higher slip factor for the MFI-2A, the pressure ratios are approximately equal. The procedures followed in the design of the MFI-1A and MFI-2A were, in general, the same; and, although the prescribed initial condition resulted in geometrical configurations that were quite dissimilar, the resulting performance characteristics compare favorably with designs for which considerable development work has been necessary.

COMPRESSION AND COMPRESSORS↗
NASA NTRS1954

Design and Test of Mixed-flow Impellers IV : Experimental Results for Impeller Models MFI-1 and MFI-2 with Changes in Blade Height

Modifications A and B of impeller model MFI-1 and A, B, and C of impeller model MFI-2 were investigated experimentally in an attempt to determine what allowance in blade height should be made for boundary layer and viscous losses in an impeller designed for isentropic compressible flow. A gradual increase in blade height was arbitrarily made from inlet to outlet in anticipation of a gradual build-up of boundary layer. Apparently there was a rapid build-up of boundary layer near the inlet in the experimental case rather than a gradual one. Therefore, the proper allowance for boundary layer cannot be described from the data obtained. Decreasing the pressure gradient along the shroud by reducing the blade height allowance apparently did little to increase the overall efficiency. At the design speed of 1400 feet per second, the overall adiabatic efficiency was increased from 0.83 for the MFI-1A to 0.85 for the MFI-1B with reduction in height; however, it is indicated from the theoretical velocity distribution and outlet surveys that the increase was due to a change from decelerating to accelerating flow along the hub rather than from any change along the shroud. It is further indicated that the consequences of a thickened or separated boundary layer depend not only on the design velocity gradients but also on the shape of the passage.

Hamrick, Joseph T↗
NASA NTRS1952

Design and Test of Mixed-flow Impellers II : Experimental Results, Impeller Model MFI-1A

An investigation was conducted to determine the performance characteristics of a mixed-flow impeller which was designed with special emphasis on the reduction or elimination of flow decelerations along wetted surfaces. The performance was investigated over a range of equivalent impeller speeds from 700 to 1600 feet per second and over a range of flow rates from maximum adiabatic temperature-rise efficiency, measured at 1-1/2 impeller diameters in a vaneless diffuser, at the design speed of 1400 feet per second were 4.00 and 0.83, respectively.

THEORY AND EXPERIMENT↗
NASA NTRS1997

High-Flux, High-Temperature Thermal Vacuum Qualification Testing of a Solar Receiver Aperture Shield

As part of the International Space Station (ISS) Phase 1 program, NASA Lewis Research Center (LERC) and the Russian Space Agency (RSA) teamed together to design, build and flight test the world's first orbital Solar Dynamic Power System (SDPS) on the Russian space station Mir. The Solar Dynamic Flight Demonstration (SDFD) program was to operate a nominal 2 kWe SDPS on Mir for a period up to 1-year starting in late 1997. Unfortunately, the SDFD mission was demanifested from the ISS phase 1 shuttle program in early 1996. However, substantial flight hardware and prototypical flight hardware was built including a heat receiver and aperture shield. The aperture shield comprises the front face of the cylindrical cavity heat receiver and is located at the focal plane of the solar concentrator. It is constructed of a stainless steel plate with a 1-m outside diameter, a 0.24-m inside diameter and covered with high-temperature, refractory metal Multi-Foil Insulation (MFI). The aperture shield must minimize heat loss from the receiver cavity, provide a stiff, high strength structure to accommodate shuttle launch loads and protect receiver structures from highly concentrated solar fluxes during concentrator off-pointing events. To satisfy Mir operational safety protocols, the aperture shield was required to accommodate direct impingement of the intensely concentrated solar image for a 1-hour period. To verify thermal-structural durability under the anticipated high-flux, high-temperature loading, an aperture shield test article was constructed and underwent a series of two tests in a large thermal vacuum chamber configured with a reflective, point-focus solar concentrator and a solar simulator. The test article was positioned near the focal plane and exposed to concentrated solar flux for a period of 1-hour. In the first test, a near equilibrium temperature of 1862 K was attained in the center of the shield hot spot. In the second test, with increased incident flux, a near equilibrium temperature of 2072 K was achieved. The aperture shield sustained no visible damage as a result of the exposures. This paper describes the aperture shield thermal-vacuum qualification test program including the test article, test facility, procedures, data collection, test success criteria, results and conclusions.

Kerslake, Thomas W.↗
NASA NTRS1999

Predictions of Substorms and Intensifications Following Northward Turnings of the IMF

Substorms are often observed to occur at the end of intervals of Southward interplanetary magnetic field (IMF), i.e. following the northward turning. Despite the significant correlation between northward turning and substorms, no direct causal relationship between northward turnings and substorms has been demonstrated. Assuming such a causal relationship, we predict that substorms will occur within a particular interval following the observation of a northward turning in the IMF. We observe 16 northward turnings following steady, southward IMF in data taken by the WIND spacecraft magnetic field instrument (MFI). To ensure that the northward turning was observed at the magnetosphere, we require that the northward turning also be observed by instruments on either one of Geotail or IMP-8 while the separation of the second spacecraft from WIND was more that 10 R(sub E). These two-spacecraft observations also allow us to predict more accurately the arrival time of the northward turning at the Earth. Of the predictions substorms, 10 predictions were clearly successful to within +/- 12 min. Five predictions failed, but the failures reveal clear shortcomings in the criteria for a northward turning that we correct. The failures were caused by an increase in the absolute value of B(sub YGSM) simultaneous with the northward turning in 3 cases, and a weak southward IMF preceding the northward turning in 2 cases. The final northward turning arrived in the recovery phase of an ongoing substorm, and resulted in unusual auroral activity. The implication of the predictability of substorms following sharp northward turnings is that the postulated causal relationship between northward turnings and substorm onset exists. The effect of increases in the absolute value of B(sub YGSM) to negate the triggering ability of northward turnings suggests that the triggering mechanism involves sharp reductions in the magnetospheric convection electric field.

Blanchard, G. T.↗
NASA NTRS1999

Some Peculiar Properties of Magnetic Clouds as Observed by the WIND Spacecraft

We aimed at understanding the common characteristics of magnetic clouds, relevant to solar-interplanetary connections, but exceptional ones were noted and are stressed here through a short compendium. The study is based on analyses of 28 good or better events (Out of 33 candidates) as identified in WIND magnetic field and plasma data. These cloud intervals are provided by WIND-MFI's Website under the URL (http://lepmfi.gsfc.nasa.gov/mfi/mag_cloud_publ.html#table). The period covered is from early 1995 to November 1998. A force free, cylindrically symmetric, magnetic field model has been applied to the field data in usually 1-hour averaged form for the cloud analyses. Some of the findings are: (1) one small duration event turned out to have an approximately normal size which was due to a distant almost "skimming" passage by the spacecraft; (2) One truly small event was observed, where 10 min averages had to be used in the model fitting; it had an excellent model fit and the usual properties of a magnetic cloud, except it possessed a small axial magnetic flux; (3) One cloud ha a dual axial-field-polarity, in the sense that the "core" had one polarity and the annular region around it had an opposite polarity. This event also satisfied the model and with a ve3ry good chi-squared value. Some others show a hint of this dual polarity; (4) The temporal distribution of occurrence clouds over the 4 years show a dip in 1996; (5) About 50 % of the clouds had upstream shocks; any others had upstream pressure pulses; (6) The overall average speed (390 km/s) of the best 28 events is less than the normally quoted for the average solar wind speed (420 km/s) The average of central cloud speed to the upstream solar wind speed was not much greater than one (1.08), even though many of these clouds were drivers of interplanetary shocks. Cloud expansion is partly the reason for the existence of upstream shocks; (7) The cloud axes often (about 50 % of the time) revealed reasonable attitudes with respect to the interpreted solar source, from simple geometry, but many bore no relationship, suggesting that their observations at 1 AU were probably those of the legs of the global cloud often having near-radial axes; (8) many clouds appear to have magnetic holes at or their their boundaries.

Berdichevsky, D.↗
NASA NTRS1999

Typical and Unusual Properties of Magnetic Clouds during the WIND Era

A list of 33 magnetic clouds as identified in WIND magnetic field and plasma data has been compiled. The intervals for these events are provided as part of NASA/GSFC, WIND-MFI's Website under the URL http://lepmfi.qsfc.nasa.gov/mfi/mag_cloud publ.html#table The period covered in this study is from early 1995 to November 1998 which primarily occurs in the quiet part of the solar cycle. A force free, cylindrically symmetric, magnetic field model has been applied to the field data in 1-hour averaged form for all of these events (except one small event where 10 min avg's were used) and the resulting fit-parameters examined. Each event was provided a semi-quantitatively determined quality factor (excellent, good or poor). A set of 28 good or better cases, spanning a surprisingly large range of values for its various properties, was used for further analysis. These properties are, for example, durations, attitudes, sizes, asymmetries, axial field strengths, speeds, and relative impact parameters. They will be displayed and analyzed, along with some related derived quantities, with emphasis on typical vs unusual properties and on the magnetic fields magnetic clouds' relationships to the Sun and to upstream interplanetary shocks, where possible. For example, it is remarkable how narrowly distributed the speeds of these clouds are, and the overall average speed (390 techniques km/s) is less than that normally quoted for the average solar wind speed (420 km/s) despite the fact that many of these clouds are d"drivers" of interplanetary shocks. On average, a cloud appears to be a little less symmetric when the spacecraft is able to pass close to the cloud's axis as compared to a farther out passage. The average longitude and latitude (in GSE) of the axes of the clouds are 85 degrees and 8 degrees, respectively, with standard deviations near 40 degrees. Also, the half=yearly averaged axial magnetic flux has approximately tripled. almost monotonically, from about 6 to 17 X 10(exp 29) Mx over the first 3.5 years of consideration, but with a large uncertainty on each of the half-year estimates, because of small sampling. If true,this finding implies an approximate tripling of the events' solar fluxes over this period as it goes into solar maximum.

Lepping, R. P.↗
NASA NTRS2001

A Multispacecraft/Instrument Case Study of the Relationship Between the Solar Wind and Ionospheric Plasma Outflow

The study of the relationship between the solar wind and ionospheric plasma outflows is fundamental to understanding the solar- terrestrial relationship. A multi-spacecraft/instrument case study has been carried out to address this relationship. On 11-26-00 the Polar spacecraft made a pass through the southern cleft region near perigee where the Thermal Ion Dynamics Experiment (TIDE) instrument observed a classic Cleft Ion Fountain/upwelling ion signature. These observations followed several pressure pulses from the solar wind as evidenced by observations from the Magnetic Field Instrument (MFI) on the WIND spacecraft. Several interesting electric field features were observed by the Electric Field Instrument (EFI) as Polar appeared to pass through a narrow region of strong currents into a region with significant oscillations at a large range of frequencies. In addition, coincident with the TIDE observations of ion outflow, the low-energy edge of the characteristic V-shape of cusp ion injections was also observed. During this same time frame the Cluster spacecrafts crossed the magnetopause in the dusk sector and observed the electric field signatures associated with this region on all three satellites. This event is addressed in detail to further detail cleft ion fountain source characteristics, to add additional data regarding the hypothesis that solar wind pressure pulses are a trigger for cleft outflow, and to investigate possible interactions among waves, ionospheric plasma, and cusp injected plasma.

Craven, Paul D.↗
NASA NTRS2003

High-Time-Resolution Study of Magnetic Holes in the Solar Wind

The objectives of this investigation are to determine the internal plasma structure of kinetic-scale and larger scale magnetic holes, and to determine their stability, their source mechanism(s), and their spatial extent. It is also of importance to determine the relationship between kinetic-scale holes and long-duration holes. As smaller and smaller magnetic depressions are investigated in order to make this a complete study, a robust criterion is necessary for distinguishing magnetic holes from random or unresolvable fluctuations in the interplanetary magnetic field. In order to resolve this ambiguity, we obtained from the MFI experiments magnetic field measurements from the WIND spacecraft at a time resolution of 46 to 184 ms over certain periods. We have also devised a measure of certainty for magnetic hole detections. The certainty factor, q, is defined as the difference between the mean magnetic field in the hole and the local magnetic field, in units of the local standard deviation of the field strength. For fullest generality, it is necessary to calculate this q over the range of available scales of interest, from 60 ms up to 300 s. This technique establishes a two dimensional matrix of relative probabilities that a hole of some duration (d) might exist in the data set at a given time (t). In identifying q-peaks in time and duration, we also come upon a natural method for distinguishing holes with internal structure from multiple holes in close proximity or holes nested inside of others. If two q-peaks are more than a half-width apart, they are simply said to be separate events.

Lazarus, Alan↗
NASA NTRS2006

In vitro Catecholamine Exposure Produces Variable Effects on the B7 Costimulatory Pathway in Human Monocytic Cells

Catecholamines have been associated with immunomodulation of the adaptive immune system towards a Th2 response in vitro. We therefore examined the role of in vitro epinephrine (EPI) and norepinephrine (NE) exposure on the B7 costimulatory expression of antigen presenting cells (APC) from human monocytic cell lines and human peripheral blood mononuclear cells (PBMC). THP1 monocytic cells and CD14+ cells from normal human PBMC were stimulated with lipopolysaccharide (LPS) and incubated with physiologic stress levels (10(exp -6) - 10(exp -8)M) of EPI or NE for 24 hours. Cells were subsequently stained with CD80 FITC, CD86 PE, and CD14 PC5 antibodies and analyzed by flow cytometry for changes in fluorescence and mean fluorescence intensity (MFI). Exposure of THP1 to EPI in vitro at concentrations of 10(exp -6), 10(exp -7) and 10(exp -8)M significantly decreased mean CD80 from 42 plus or minus 0.7% to 11 plus or minus 0.44%, 19.1 plus or minus 2.0%, and 30.7 plus or minus 2.1% expression, respectively (p less than 0.01). In addition, CD86 expression increased with EPI at 10(exp -6), 10(exp -7) and 10(exp -8) M from 9.2 plus or minus 0.52% to 41 plus or minus 3.8%, 26.4 plus or minus 1.9%, and 15.74 plus or minus 1.8% expression, respectively (p less than 0.01). Similar results for mean CD80 and CD86 percent expression were observed for CD14+ cells from PBMC with a sample size of N = 6 and for NE when substituted for EPI. The data show that in vitro exposure to catecholamines significantly decreases %CD86 expression and significantly increases %CD86 expression in THP1 cells and human CD14+ APC. Previous studies have suggested an association between increased CD86 expression and TH2 activity. Thus, these data suggest that immunomodulation by catecholamines results in part by the variable effects of the B7 costimulatory pathway in APC.

Salicru, A. N.↗
NASA NTRS2008

Hybrid Multifoil Aerogel Thermal Insulation

This innovation blends the merits of multifoil insulation (MFI) with aerogel-based insulation to develop a highly versatile, ultra-low thermally conductive material called hybrid multifoil aerogel thermal insulation (HyMATI). The density of the opacified aerogel is 240 mg/cm3 and has thermal conductivity in the 20 mW/mK range in high vacuum and 25 mW/mK in 1 atmosphere of gas (such as argon) up to 800 C. It is stable up to 1,000 C. This is equal to commercially available high-temperature thermal insulation. The thermal conductivity of the aerogel is 36 percent lower compared to several commercially available insulations when tested in 1 atmosphere of argon gas up to 800 C.

Sakamoto, Jeffrey↗
NASA NTRS2010

Interplanetary Magnetic Field Power Spectrum Variations: A VHO Enabled Study

The newly reprocessed high time resolution (11/22 vectors/sec) Wind mission interplanetary magnetic field data and the solar wind key parameter search capability of the Virtual Heliospheric Observatory (VHO) affords an opportunity to study magnetic field power spectral density variations as a function of solar wind conditions. In the reprocessed Wind Magnetic Field Investigation (MFI) data, the spin tone and its harmonics are greatly reduced that allows the meaningful fitting of power spectra to the approx.2 Hz limit above which digitization noise becomes apparent. The power spectral density is computed and the spectral index is fitted for the MHD and ion inertial regime separately along with the break point between the two for various solar wind conditions . The time periods of fixed solar wind conditions are obtained from VHO searches that greatly simplify the process. The functional dependence of the ion inertial spectral index and break point on solar wind plasma and magnetic field conditions will be discussed

Szabo, A.↗
NASA NTRS2011

Interplanetary Magnetic Field Power Spectrum Variations: A VHO Enabled Study

The newly reprocessed high time resolution (11/22 vectors/sec) Wind mission interplanetary magnetic field data and the solar wind key parameter search capability of the Virtual Heliospheric Observatory (VHO) affords an opportunity to study magnetic field power spectral density variations as a function of solar wind conditions. In the reprocessed Wind Magnetic Field Investigation (MFI) data, the spin tone and its harmonics are greatly reduced that allows the meaningful fitting of power spectra to the ~2 Hz limit above which digitization noise becomes apparent. The power spectral density is computed and the spectral index is fitted for the MHD and ion inertial regime separately along with the break point between the two for various solar wind conditions. The time periods of fixed solar wind conditions are obtained from VHO searches that greatly simplify the process. The functional dependence of the ion inertial spectral index and break point on solar wind plasma and magnetic field conditions will be discussed

Szabo, A.↗
NASA NTRS2011

Interplanetary Magnetic Field Power Spectrum Variations in the Inner Heliosphere: A Wind and MESSENGER Study

The newly reprocessed high time resolution (11/22 vectors/sec) Wind mission interplanetary magnetic field data and the similar observations made by the MESSENGER spacecraft in the inner heliosphere affords an opportunity to compare magnetic field power spectral density variations as a function of radial distance from the Sun under different solar wind conditions. In the reprocessed Wind Magnetic Field Investigation (MFI) data, the spin tone and its harmonics are greatly reduced that allows the meaningful fitting of power spectra to the approx.2 Hz limit above which digitization noise becomes apparent. The powe'r spectral density is computed and the spectral index is fitted for the MHD and ion inertial regime separately along with the break point between the two for various solar wind conditions. Wind and MESSENGER magnetic fluctuations are compared for times when the two spacecraft are close to radial and Parker field alignment. The functional dependence of the ion inertial spectral index and break point on solar wind plasma and magnetic field conditions will be discussed.

Szabo, Adam↗