SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
MFC Transient Testing Capabilities and Fuel Fabrication capabilities are summarized in this slide deck. Slides are included for TREAT and TREAT capabilities, EFF, FASB, FMF, ZPPR, AFF, and the Fuels Fabrication Modernization Capability. First use of this slide deck is for presentation at Westinghouse Electric Corporation, but there will be other uses later.
The Irradiated Material Properties Accelerated Characterization Test (IMPACT) series of experiments will irradiate three metallic fuel alloy specimens with embedded thermal conductivity probes in the Advanced Test Reactor (ATR). Metallic fuel alloys have long been under investigation for use in advanced reactors on account of their high thermal conductivity. Metallic fuel undergoes dramatic microstructural changes early in life due to fission gas swelling until ~2-3 at% burnup when pores interconnect, thus allowing fission gas to escape into the fuel pin plenum and swelling effectively ceases. The evolution of metallic fuel thermal conductivity during this early phase has never been successfully measured in situ. This experiment will be designed to use advances in measurement sciences to characterize how thermal transport properties evolve while in reactor. The IMPACT experiment consists of three metallic fuel rodlets with thermal conductivity probes axially centered within the fuel specimen. This presentation is an overview of the IMPACT-01 assembly process with a focus MFC fuel fabrication and experiment assembly steps.
Abstract Microfibrillated cellulose (MFC) with reinforcing effects is a useful building block in the fabrication of flexible and thin supercapacitors. Herein, a hybrid tin oxide‐cellulose nanocomposite was hydrothermally produced and coated on MFC thin films to form a supercapacitor. The hybrid tin oxide‐cellulose thin films were structurally analyzed using scanning electrode microscopy, Fourier transform infrared spectroscopy and x‐ray diffraction. The cellulose thin film with the highest loading of hybrid tin oxide‐cellulose nanocomposite exhibited a specific capacitance of 225.88 F g −1 at 100 mV s −1 and 486.38 F g −1 at 20 mV s −1 in the three‐electrode electrochemical system. In addition, it revealed good cyclic stability up to 40 cycles run continuously with 95% cyclic retention. The high specific capacitance and superior cyclic stability could be related to the enhanced charge mobility and ion diffusion between the solid and electrolyte interface. The cellulose thin film coated with flower‐like hybrid nanocomposite showed great potential in energy storage.
In a metal fiber composite (MFC) additive manufacturing (AM) method, a layer of polymer structures is deposited using a fused filament fabrication (FFF) printer assembly comprising at least one nozzle. Subsequently, an MFC printer assembly is used to embed a continuous metal fiber into one or more of the polymer structures of the layer. The embedding is achieved by heating the metal fiber and applying pressure to the metal fiber using an embedding surface of the MFC printer assembly. The heated metal fiber melts polymer adjacent thereto, thereby allowing the pressure to embed the metal fiber into the polymer structure. Using the MFC-AM method, various composite structures can be formed, such as novel heat exchangers that may otherwise be difficult or impossible to fabricate via other manufacturing techniques.
A. The Microreactor Applications Research Validation and Evaluation (MARVEL) reactor will offer experimental capabilities that are not currently available at DOE’s national laboratories. Idaho National Laboratory (INL), operated for the U.S. Department of Energy (DOE) by Battelle Energy Alliance, LLC (BEA) (Contractor hereafter) is procuring services for the design, analysis, fabrication, testing and delivery of a Secondary Coolant Equipment system (SCE). This specification contains the requirements for design, analysis, fabrication, testing and delivery of the SCE as described herein. The MARVEL reactor is a microreactor which uses eutectic sodium-potassium alloy (NaK) as a primary coolant. The primary coolant is circulated through four primary loops by natural convection of the coolant. In each loop is a closed well which will accommodate an intermediate heat exchanger (IHX) for extracting heat from the loop. These wells will be referred to in this specification as the “IHX wells.” It is intended for the IHX containment to also be filled with NaK. The MARVEL design team has determined that a Heat Extraction System (HES) using pumped NaK will be used to extract heat from the IHXs and deliver it to a downstream system for power generation or alternate process heat users. This Heat Extraction System will enable MARVEL operations including the ability to test, demonstrate, and address issues related to installation, startup, and operations. In addition, it will allow down-stream utilization of process heat for various uses. The objective of this specification is to develop the final design for the HES Secondary Coolant Equipment system (SCE) that will be used as the core of the HES. This system provides control of the NaK circulation between the MARVEL reactor and the subsequent process heat utilization systems. It does not include design of the Intermediate Heat Exchangers and piping inside the T-REXc pit in which the reactor is located. B. The MARVEL microreactor will be installed in the Transient Reactor Test Facility (TREAT) building in the Transient Reactor Test (TREAT) Micro-Reactor Experiment Cell (T-REXc) C. An INL Subcontractor has developed a conceptual design for this system per SPC-71145, referred to in that specification as the Process Heat Extraction System. SPC-71260 is based on the pumped NaK loop concept developed under SPC-71145. D. The SCE system design and (as option scope) fabrication shall be provided by the awardee of the subcontract (Subcontractor hereafter) pertaining to this Specification. Prior to shipment, the SCE will be fabricated, assembled, and tested at the Subcontractor’s facility. After successful completion of acceptance testing, the SCE and associated equipment will be shipped to the Materials and Fuels Complex (MFC) at the INL (Contractor’s Facility hereafter) to be installed by others in TREAT/T-REXc.
TRIPWIRE is a multi-modal system for containment verification in inaccessible radiological and nuclear waste repositories. The sensing modes are focused on radiation, electromagnetic and vibration. The radiation detection component has been developed over the last three years at Idaho National Laboratory (INL). This development has focused on the fabrication, characterization, and testing of long-length (greater than 10-m) plastic scintillating fibers. This fiscal year, the focus of TRIPWIRE has been on field testing and demonstration of the radiation sensing component in a relevant environment. After reviewing the static storage facilities at INL, the Radioactive Scrap Waste Facility (RSWF) south storage area outside the Materials and Fuels Complex (MFC) was selected due to its periodic changes in configuration and inventory. This report summarizes the research outcomes for the work performed in fiscal year (FY) 2023.