Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MANNED REENTRY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1960

An Analysis of Ablation-Shield Requirements for Manned Reentry Vehicles

The problem of sublimation of material and accumulation of heat in an ablation shield is analyzed and the results are applied to the reentry of manned vehicles into the earth's atmosphere. The parameters which control the amount of sublimation and the temperature distribution within the ablation shield are determined and presented in a manner useful for engineering calculation. It is shown that the total mass loss from the shield during reentry and the insulation requirements may be given very simply in terms of the maximum deceleration of the vehicle or the total reentry time.

Roberts, Leonard↗
NASA NTRS1960

Landing Energy Dissipation for Manned Reentry Vehicles

The film shows experimental investigations to determine the landing-energy-dissipation characteristics for several types of landing gear for manned reentry vehicles. The landing vehicles are considered in two categories: those having essentially vertical-descent paths, the parachute-supported vehicles, and those having essentially horizontal paths, the lifting vehicles. The energy-dissipation devices include crushable materials such as foamed plastics and honeycomb for internal application in couch-support systems, yielding metal elements as part of the structure of capsules or as alternates for oleos in landing-gear struts, inflatable bags, braking rockets, and shaped surfaces for water impact.

REENTRY VEHICLES↗
NASA NTRS1960

Analytical Investigation of the Dynamic Behavior of a Nonlifting Manned Reentry Vehicle

An analytic investigation was made of the dynamic behavior of a nonlifting manned reentry vehicle as it descended through the atmosphere. The investigation included the effects of variations in the aerodynamic stability derivatives, the spin rate, reentry angle, and velocity. The effect of geostrophic winds and of employing a drogue parachute for stability purposes were also investigated. It was found that for the portion of the flight above a Mach number of 1 a moderate amount of negative damping could be tolerated but below a Mach number of 1 good damping is necessary. The low-speed stability could be improved by employing a drogue parachute. The effectiveness of the drogue parachute was increased when attached around the periphery of the rear of the vehicle rather than at the center. Neither moderate amounts of spin or the geostrophic winds had appreciable effects on the stability of the vehicle. The geostrophic winds and the reentry angle or velocity all showed important effects on the range covered by the reentry flight path.

Lichtenstein, Jacob H.↗
NASA NTRS1960

Landing Energy Dissipation for Manned Reentry Vehicles

Analytical and experimental investigations have been made to determine the landing-energy-dissipation characteristics for several types of landing gear for manned reentry vehicles. The landing vehicles are considered in two categories: those having essentially vertical-descent paths, the parachute-supported vehicles, and those having essentially horizontal paths, the lifting vehicles. The energy-dissipation devices discussed are crushable materials such as foamed plastics and honeycomb for internal application in couch-support systems, yielding metal elements as part of the structure of capsules or as alternates for oleos in landing-gear struts, inflatable bags, braking rockets, and shaped surfaces for water impact. It appears feasible to readily evaluate landing-gear systems for internal or external application in hard-surface or water landings by using computational procedures and free-body landing techniques with dynamic models. The systems investigated have shown very interesting energy-dissipation characteristics over a considerable range of landing parameters. Acceptable gear can be developed along lines similar to those presented if stroke requirements and human-tolerance limits are considered.

Fisher, Lloyd J., Jr.↗
NASA NTRS1960

Radiation and Ablation Cooling for Manned Reentry Vehicles

The necessity of reducing heat transfer to reentry vehicles has led I to the consideration of both radiative and ablation shields. The paper reviews briefly the heating problems for manned vehicles and the means whereby ablation and radiation afford thermal protection. The principal energy disposal and weight parameters are then presented and their relation to the vehicle and trajectory parameters is discussed. A comparative analysis of three types of ablation shield is made and broad conclusions are drawn as to the type of shield most appropriate to manned reentry vehicles.

Roberts, L.↗
NASA NTRS1960

Noise Considerations for Manned Reentry Vehicles

Noise measurements pertaining mainly to the static firing, launch, 0 and exit flight phases are presented for three rocket-powered vehicles 4 in the Project Mercury test program. Both internal and external data 4 from onboard recordings are presented for a range of Mach numbers and dynamic pressures and for different external vehicle shapes. The main sources of noise are noted to be the rocket engines during static firing and launch and the aerodynamic boundary layer during the high-dynamic-pressure portions of the flight. Rocket-engine noise measurements along the surface of the Mercury Big Joe vehicle were noted to correlate well with data from small models and available data for other large rockets. Measurements have indicated that the aerodynamic noise pressures increase approximately as the dynamic pressure increases and may vary according to the external shape of the vehicle, the highest noise levels being associated with conditions of flow separation. There is also a trend for the aerodynamic noise spectra to peak at higher frequencies as the flight Mach number increases.

Hilton, David A.↗
NASA NTRS1961

Landing of Manned Reentry Vehicles

Landing characteristics were investigated using dynamic models. The landing speeds for several let-down systems are simulated. Demonstrations include: (1) the vertical landing of parachute-supported capsules on water; (2) reduction of landing acceleration by shaping the impact surface for water entry; (3) problems created by horizontal velocity due to wind; (4) the use of energy absorbers (yielding metal legs or torus bags) for land or water landings; (5) problems associated with horizontal land landings; (6) the use of a paraglider to aid in vehicle direction control; (7) a curved undersurface to serve as a skid-rocker to convert sinking-speed energy into angular energy; (8) horizontal-type landing obtained with winged vehicles on a hard runway; (9) the dangers of high-speed water landings; and (10) the positive effects of parachute support for landing winged vehicles.

Source record↗
NASA NTRS2008

Simulated Reentry Heating by Torching

The two first order reentry heating parameters are peak heating flux (W/cm2) and peak heat load (kJ/cm2). Peak heating flux (and deceleration, gs) is higher for a ballistic reentry and peak heat load is higher for a lifting reentry. Manned vehicle reentries are generally lifting reentries at nominal 1-5 gs so that personnel will not be crushed by high deceleration force. A few off-nominal manned reentries have experienced 8 or more gs with corresponding high heating flux (but below nominal heat load). The Shuttle Orbiter reentries provide about an order of magnitude difference in peak heating flux at mid-bottom (TPS tiles, approximately 6 W/cm2 or 5 BTU/ft2- sec) and leading edge (RCC, approximately 60 W/cm2 or 50 BTU/ft2- sec). Orion lunar return and Mars sample lander are of the same order of magnitude as orbiter leading edge peak heat loads. Flight temperature measurements are available for some orbiter TPS tile and RCC locations. Return-to-Flight on-orbit tile-repair-candidate-material-heating performance was evaluated by matching propane torch heating of candidate-materials temperatures at several depths to orbiter TPS tile flight-temperatures. Char and ash characteristics, heat expansion, and temperature histories at several depths of the cure-in-place ablator were some of the TPS repair material performance characteristics measured. The final char surface was above the initial surface for the primary candidate (silicone based) material, in contrast to a receded surface for the Apollo-type ablative heat shield material. Candidate TPS materials for Orion CEV (LEO and lunar return), and for Mars sample lander are now being evaluated. Torching of a candidate ablator material, PICA, was performed to match the ablation experienced by the STARDUST PICA heat shield. Torching showed that the carbon fiberform skeleton in a sample of PICA was inhomogeneous in that sample, and allowed measurements (of the clumps and voids) of the inhomogeneity. Additional reentry heating-performance characterizations of high temperature insulation materials were performed.

Harvey, Gale A.↗
NASA NTRS2008

Simulated Reentry Heating by Torching

The two first order reentry heating parameters are peak heating flux (W/square cm) and peak heat load (kJ/square cm). Peak heating flux (and deceleration, gs) is higher for a ballistic reentry and peak heat load is higher for a lifting reentry. Manned vehicle reentries are generally lifting reentries at nominal 1-5 gs so that personnel will not be crushed by high deceleration force. A few off-nominal manned reentries have experienced 8 or more gs with corresponding high heating flux (but below nominal heat load). The Shuttle Orbiter reentries provide about an order of magnitude difference in peak heating flux at mid-bottom (TPS tiles, approximately 6 W/square cm or 5 BTU/square ft - sec) and leading edge (RCC, approximately 60 W/square cm or 50 BTU/square ft- sec). Orion lunar return and Mars sample lander are of the same order of magnitude as orbiter leading edge peak heat loads. Flight temperature measurements are available for some orbiter TPS tile and RCC locations. Return-to-Flight on-orbit tile-repair-candidate-material-heating performance was evaluated by matching propane torch heating of candidate-materials temperatures at several depths to orbiter TPS tile flight-temperatures. Char and ash characteristics, heat expansion, and temperature histories at several depths of the cure-in-place ablator were some of the TPS repair material performance characteristics measured. The final char surface was above the initial surface for the primary candidate (silicone based) material, in contrast to a receded surface for the Apollo-type ablative heat shield material. Candidate TPS materials for Orion CEV (LEO and lunar return), and for Mars sample lander (MSL) are now being evaluated. Torching of a candidate ablator material, PICA, was performed to match the ablation experienced by the STARDUST PICA heat shield. Torching showed that the carbon fiberform skeleton in a sample of PICA was inhomogeneous in that sample, and allowed measurements (of the clumps and voids) of the inhomogeneity. Additional reentry heating-performance characterizations of high temperature insulation materials were performed.

Harvey, Gale A.↗