Engineering PapersSearch

SEARCH · Engineering Papers

Results for “Localized deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Strain localization during deformation of Westerly granite

A specimen of Westerly granite was cyclically loaded to near failure at 50 MPa confining pressure. Holographic interferometry provided detailed measurements of localized surface deformations during loading and unloading. The data are consistent with deformation occurring primarily elastically at low differential stress; in conjunction with one incipient fault zone between approximately 350 and 520 MPa differential stress; and in conjunction with a second incipient fault zone above 580 MPa and/or during creep. During unloading only one fault zone, that which is active at the intermediate stress levels during loading, is seen to recede.

Brodsky, N. S.

Ridge belts - Evidence for regional- and local-scale deformation on the surface of Venus

Models for the formation of the ridge belt fan assemblage on Venus are evaluated through consideration of the orientation, spatial distribution, topographic expression, and wavelengths of observed tectonic surface features. A compressional mechanism is favored for long wavelength deformation corresponding to the spacing of ridge belts (300 - 400 km). However, short wavelength ridges and grooves (10 - 20 km) that are contained within belts and trend parallel to them are likely to be compressional and extensional, and to reflect both regional and local stress fields. It is hypothesized that large-scale (much greater than ridge spacing) early-stage mantle downwelling is the source of regional compression responsible for the establishment of the long wavelength of deformation.

Zuber, M. T.

The influence of a local wall deformation on the development of natural instabilities in a laminar boundary layer

The natural instabilities which propagate in the laminar boundary layer of a flat plate composed of intermittent wave trains are described. A spectral analysis determines the frequency range and gives a frequency and the harmonic 2 only if there is a wall deformation. This analysis provides the amplitude modulation spectrum of the instabilities. Plots of the evolution of power spectral density are compared with the numerical results obtained from the resolve of the Orr-Sommerfeld equation, while the harmonic is related to a micro-recirculating flow near the wall deformation.

Burnel, S.

Elastohydrodynamic film thickness measurements of artificially produced surface dents and grooves

Elastohydrodynamic (EHD) film thickness measurements using optical interferometry were made of artificially produced dents and grooves under rolling and sliding conditions. These measurements are compared to stylus traces of the dent and groove profiles to determine the local deformation associated with micro-EHD pressure generation. The surface geometry associated with the dents and grooves became intimately involved in the lubrication process itself, creating local pressure variations that substantially deformed the local surface geometry, particularly under sliding conditions. The rolling results implied surface initiated fatigue, and the sliding results showed clearly the EHD surface interactions that must occur prior to scuffing failure.

Wedeven, L. D.

Elastohydrodynamic film thickness measurements of artificially produced surface dents and grooves

Elastohydrodynamic (EHD) film thickness measurements using optical interferometry have been made of artificially produced dents and grooves under rolling and sliding conditions. These measurements are compared to stylus traces of the dent and groove profiles to determine the local deformation associated with micro-EHD pressure generation. The surface geometry associated with the dents and grooves is seen to become intimately involved in the lubrication process itself, creating local pressure variations that substantially deform the local surface geometry, particularly under sliding conditions. The rolling results have implications concerning surface initiated fatigue and the sliding results show clearly the EHD surface interactions that must occur prior to scuffing failure.

Wedeven, L. D.

Local flow structures defined by kinematic events in isotropic turbulence

The spatial structure of turbulent motion in incompressible isotropic turbulence is investigated using a conditional average in which the conditional event specifies the local deformation tensor in addition to the local velocity vector. This average gives the best estimate of the flow field around a fixed point x given the kinematic state at x. Estimates are calculated for various kinematic states in isotropic turbulence, including pure translation, pure shear, plane strain, axisymmetric strain, and pure rotation. It is demonstrated that the large-scale motion is dominated by a vortex ring structure associated with the translational component, except at critical points of the velocity vector field.

Adrian, R. J.

Hybrid-coordinate spacecraft dynamics using large-deformation modal coordinates

For a vehicle amenable to idealization as a set of n + 1 rigid bodies interconnected by n line hinges (implying tree topology), a set of minimum-dimension matrix equations of motion is recorded in terms of variables including the relative rotations of contiguous bodies. When a substructure or portion of the vehicle is subjected to large gross deformations but is restricted to 'small' strains or local deformations, the n-body model is (for sufficiently large n) assumed to experience 'small' relative rotations of contiguous bodies within the substructure, and the equations of motion are linearized in these variables. The application of coordinate transformations and truncations to the linearized subset of the system equations of motion then produces a hybrid-coordinate formulation of the problem involving both discrete and distributed coordinates.

Likins, P. W.

Finite-element models of continental extension

Numerical models of the initial deformation of extending continental lithosphere, computed to investigate the control of preexisting thermal and mechanical heterogeneities on the style of deformation, are presented. The finite element method is used to calculate deformation with a viscoelastic-plastic model for the lithosphere. Comparisons of the results of analytic models and finite-element models using this method show that good results may be obtained by the numerical technique, even with elements containing both brittle and viscoelastic sampling points. It is shown that the gross style of initial extensional deformation is controlled by the depth and width of the initial heterogeneity which localizes deformation.

Lynch, H. David

Deformation analysis of boron/aluminum specimens by moire interferometry

Whole-field surface deformations were measured for two slotted tension specimens from multiply laminates, one with 0 deg fiber orientation in the surface ply and the other with 45 deg orientation. Macromechanical and micromechanical details were revealed using high-sensitivity moire interferometry. Although global deformations of all plies were essentially equal, numerous random or anomalous features were observed. Local deformations of adjacent 0 deg and 45 deg plies were very different, both near the slot and remote from it, requiring large interlaminar shear strains for continuity. Shear strains were concentrated in the aluminum matrix. For 45 deg plies, a major portion of the deformation was by shear; large plastic slip of matrix occurred at random locations in 45 deg plies, wherein groups of fibers slipped relative to other groups. Shear strains in the interior, between adjacent fibers, were larger than the measured surface strains.

Post, Daniel

Strain accumulation and surface deformation along the San Andreas, California

The goal of this project remains to be the achievement of a better understanding of the regional and local deformation and crustal straining processes in western North America, particularly the effect of the San Andreas and nearby faults on the spatial and temporal crustal deformation behavior. Construction of theoretical models based on the mechanics of coupled elastic plate/viscoelastic foundation and large scale crack mechanics provide a rational basis for the interpretation of seismic and aseismic anomalies and expedite efforts in forecasting the stability of plate boundary deformations. In the present period, special focus is placed on the 3-D effect of irregular fault locked patches on the ground measured deformation fields. Specifically, use is made of a newly developed 3-D boundary element program to analyze the fault slip and vertical ground motion in the Parkfield area on the San Andreas.

Li, Victor C.

Elastohydrodynamic film thickness measurements of artificially produced nonsmooth surfaces

Optical interferometry is used to measure the elastohydrodynamic (EHD) film thickness associated with artificially produced nonsmooth surfaces. The nonsmooth surfaces are produced by modifying the surfaces of highly-polished balls with irregularities in the form of multiple grooves and dents. By closely spacing these irregularities it is possible not only to produce depressions on the surface of the balls but also to generate pseudo asperities. The average roughness wavelength of this artificially-produced, nonsmooth, surface approximates the average fundamental roughness wavelength found on surfaces of some mechanical elements operating under concentrated contact. By comparing the measured film thickness profiles to the stylus traces of the irregularities, it was possible to observe the local deformations associated with micro-EHD pressure generation. In both pure rolling and pure sliding conditions the artificially-produced asperities are deformed and complete separation exists between them and the mating surface. Such findings demonstrate the importance of local surface topography and resulting micro-EHD effects on the film thickness between rough surfaces in concentrated contact. Sliding data are presented which demonstrate a severe constriction, caused by the irregularities, at the exit of the Hertzian region.

Cusano, C.

Elastohydrodynamic film thickness measurements of artificially-produced nonsmooth surfaces

Optical interferometry is used to measure the elastohydrodynamic (EHD) film thickness associated with artificially produced, nonsmooth surfaces. The nonsmooth surfaces are produced by modifying the surfaces of highly-polished balls with irregularities in the form of multiple grooves and dents. By closely spacing these irregularities, it is possible not only to produce depressions on the surface of the balls but also to generate pseudo asperities. The average roughness wavelength of this artificially-produced, nonsmooth surface approximates the average fundamental roughness wavelength found on surfaces of some mechanical elements operating under concentrated contact. By comparing the measured film thickness profiles to the stylus traces of the irregularities, it is possible to observe the local deformations associated with micro-EHD pressure generation. In both pure rolling and pure sliding conditions, the artificially-produced 'asperities' are deformed and complete separation exists between them and the mating surface. Such findings demonstrate the importance of local surface topography and resulting micro-EHD effects on the film thickness between rough surfaces in concentrated contact. In addition, sliding data are presented which demonstrate a severe constriction, caused by the irregularities, at the exit of the Hertzian region.

Cusano, C.

Orientation of late Precambrian sutures in the Arabian-Nubian shield

Recent tectonic models have resulted in conflicting descriptions of how the late Precambrian sutures of the Arabian-Nubian shield extend into northeast Africa. The Hamisana shear zone in northeastern Sudan is critical to this discussion because it truncates and disrupts two sutures, the Allaqi-Heiani and the Onib-Sol Hamed. Analysis of field structural data, Thematic Mapper imagery, and Rb-Sr and U-Pb geochronology suggests that the Allaqi-Heiani suture is the western extension of the Onib-Sol Hamed suture and that both make up the exposed parts of a far-traveled, polydeformed ophiolitic nappe complex. Subsequent deformation localized in the Hamisana shear zone disrupted this nappe and displaced the suture between 660 and 550 Ma during regional deformation associated with the Najd fault system. These results indicate that at least one suture extends westward into the interior of northern Africa.

Stern, Robert J.

Eastern Ishtar Terra: Tectonic evolution derived from recognized features

Previous analyses have recognized several styles and orientations of compressional deformation, crustal convergence, and crustal thickening in Eastern Ishtar Terra. An east to west sense of crustal convergence through small scale folding, thrusting, and buckling is reflected in the high topography and ridge-and-valley morphology of Maxwell Montes and the adjacent portion of Fortuna Tessera. This east to west convergence was accompanied by up to 1000 km of lateral motion and large scale strike-slip faulting within two converging shear zones which has resulted in the present morphology of Maxwell Montes. A more northeast to southwest sense of convergence through large scale buckling and imbrication is reflected in large, northwest-trending scarps along the entire northern boundary of Ishtar Terra, with up to 2 km of relief present at many of the scarps. It was previously suggested that both styles of compression have occurred at the expense of pre-existing tessera regions which have then been overprinted by the latest convergence event. The difference in style is attributed mostly to differences in the properties of the crust converging with the tessera blocks. If one, presumably thick, tessera block converges with another tessera region, then the widespread, distributed style of deformation occurs, as observed in western Fortuna Tessera. However, if relatively thin crust (such as suggested for the North Polar Plains converges with thicker tessera regions, then localized deformation occurs, as reflected in the scarps along Northern Ishtar Terra. The purpose is to identify the types of features observed in Eastern Ishtar Terra. Their potential temporal and spatial relationships, is described, possible origins for them is suggested, and how the interpretation of some of these features has led to the multiple-style tectonic evolution model described is shown.

Vorderbruegge, R. W.

A coupled fluid-structure dynamic analysis for water impact loads

In this paper a nonlinear transient, hydroelastic method is developed for response analysis of the Space Shuttle recoverable booster on water impact. At each time step, coupled equations of fluid flow and structure dynamics are solved with an iterative, self-correcting process. Rigid body motions are represented by large angle equations. Local deformations are represented by a NASTRAN-generated model of the three-dimensional structure. The fluid is represented by series solutions of the potential flow equation which include the effects of the local structure motions. The resulting water loads and structural stresses obtained will aid in qualification of the final structural design. Comparisons are made to experimental impact data to validate the method.

Herting, D. N.

Low velocity impact analysis with NASTRAN

A nonlinear elastic force-displacement relationship is used to calculate the transient impact force and local deformation at the point of contact between impactor and target. The nonlinear analysis and transfer function capabilities of NASTRAN are used to define a finite element model that behaves globally linearly elastic, and locally nonlinear elastic to model the local contact behavior. Results are presented for two different structures: a uniform cylindrical rod impacted longitudinally; and an orthotropic plate impacted transversely. Calculated impact force and transient structural response of the targets are shown to compare well with results measured in experimental tests.

Trowbridge, Daniel A.

Topology of three-dimensional, variable density flows

This paper is concerned with the interpretation of unsteady, variable-density flow fields. The topology of the flow is determined by finding critical points and identifying the character of local solution trajectories. The time evolution of the flow is studied by following the paths of the critical points in the three-dimensional space of invariants of the local deformations tensor. The methodology can be applied to any smooth vector field and its associated gradient tensor including the vorticity and pressure gradient fields. This approach provides a framework for describing the geometry of complex flow patterns. Concisely summarizing that geometry in the space of invariants of the local gradient tensor may be a useful way of gaining insight into time-dependent processes described by large computational data bases. Applications to the descriptions of a flickering diffusion flame and a compressible wake are discussed.

Cantwell, Brian

Plastic deformation - Its role in fatigue crack propagation

Recognizing the fact that the effective driving force Delta-K(eff) determines the fatigue crack propagation (FCP) rate and that the shear strain, which is considered to develop due to an occurrence of crack closure, primarily contributes to the plastic deformation, an effort is made here to elucidate the role of plastic deformation in FCP by developing a correlation between the Delta-K(eff) and the applied driving force (Delta-K) with shear strain as variable. The disparity between Delta(K)eff) and Delta-K, which apparently increases with shear strain level, persists at lower values of Delta-K. This suggests a strong influence of the degree of localized deformation on the FCP rates in the near threshold level. Hence, an improvement of FCP rates in the near threshold level should follow an effort that promotes the plastic deformation near the crack tip to a greater degree. This approach could explain the effect of the grain size, microstructure, environment, R-ratio and crack size on the near-threshold FCP rates.

Mazumdar, P. K.