Results for “Lifting map” | Engineering Papers

NASA NTRS1993

Approaches to high aspect ratio triangulations

In aerospace computational fluid dynamics calculations, high aspect ratio, or stretched, triangulations are necessary to adequately resolve the features of a viscous flow around bodies. In this paper, we explore alternatives to the Delaunay triangulation which can be used to generate high aspect ratio triangulations of point sets. The method is based on a variation of the lifting map concept which derives Delaunay triangulations from convex hull calculations.

Posenau, M.-A.↗

NASA NTRS1999

Influence of Buoyant Convection on the Stability of Enclosed Laminar Flames

An investigation of the stability limits of Enclosed Laminar Flames (ELF) was conducted in the Middeck Glovebox (MGBX) facility on the STS-87 Space Shuttle mission (November to December 1997). The primary objective of the ELF glovebox investigation is to determine the effect of buoyancy on the stability of round, laminar, gas-jet diffusion flames in a co-flow air duct. Comparison tests were conducted in normal gravity to allow isolation and identification of the influence of buoyancy. The results were used to map the lift-off and blow-out stability limits as a function of the fuel and air velocities for the two buoyancy conditions. Approximately 50 tests were conducted during the Space Shuttle mission, using a 50/50 mixture (volume basis) of methane and nitrogen as the fuel. The experimental results verified the hypothesis that substantially greater velocities are required to destabilize the flame in microgravity. The increase in air velocity required to induce lift off in microgravity (compared to normal gravity) was nearly equal to the increase required to induce blow out. Furthermore, the air velocity increase was relatively independent of the fuel flow, except at low fuel flows. At high fuel flows, it was found that the microgravity flames tend to immediately blow out after lift off. This is in agreement with the free-jet theory which suggests that stable lifted flames are not possible for fuels with a Schmidt number of 0.5<Sc<l, such as the diluted methane used in this study. However, stable lifted flames were observed in microgravity at low fuel flows, and in normal gravity, despite the fuel's low Schmidt number. The discrepancy between the experimental data and the theory of Chung and Lee is presumably due to the differences in the flow condition; namely, the ducted flow versus a free jet, and a non-similar velocity profile versus a self-similar profile.

Brooker, John E.↗

NASA NTRS1990

Control law system for X-Wing aircraft

Control law system for the collective axis, as well as pitch and roll axes, of an X-Wing aircraft and for the pneumatic valving controlling circulation control blowing for the rotor. As to the collective axis, the system gives the pilot single-lever direct lift control and insures that maximum cyclic blowing control power is available in transition. Angle-of-attach de-coupling is provided in rotary wing flight, and mechanical collective is used to augment pneumatic roll control when appropriate. Automatic gain variations with airspeed and rotor speed are provided, so a unitary set of control laws works in all three X-Wing flight modes. As to pitch and roll axes, the system produces essentially the same aircraft response regardless of flight mode or condition. Undesirable cross-couplings are compensated for in a manner unnoticeable to the pilot without requiring pilot action, as flight mode or condition is changed. A hub moment feedback scheme is implemented, utilizing a P+I controller, significantly improving bandwidth. Limits protect aircraft structure from inadvertent damage. As to pneumatic valving, the system automatically provides the pressure required at each valve azimuth location, as dictated by collective, cyclic and higher harmonic blowing commands. Variations in the required control phase angle are automatically introduced, and variations in plenum pressure are compensated for. The required switching for leading, trailing and dual edge blowing is automated, using a simple table look-up procedure. Non-linearities due to valve characteristics of circulation control lift are linearized by map look-ups.

Lawrence, Thomas H.↗

NASA NTRS1990

Patterns of vortex shedding from an oscillating circular cylinder

Vortex shedding from an oscillating circular cylinder was numerically investigated at Re = 100 with the Navier-Stokes equations and the new boundary conditions. The detailed shedding patterns are characterized by means of streakline plotting and lift-coefficient curves. A parameter map is presented which distinguishes the synchronized shedding from the asynchronous and the double vortices shedding from the single vortex shedding. The computational result is in good agreement with earlier experimental results.

Chang, Keun-Shik↗

NASA NTRS1955

Lift on a bent, flat plate

The lift on a bent, flat plate is calculated exactly by the use of conformal mapping. Results are presented in terms permitting direct determination of the angle of zero lift, the lift coefficient, and the lift-curve slope for any flap-chord ratio, flap-deflection angle, and angle of attack.

WING FLAPS - DEFLECTION↗

NASA NTRSDate not supplied

Investigation of Aerodynamic Matching Sensitivities for Conceptual Design

A methodology for aerodynamic matching was implemented in the Higher fidelity Conceptual Design and structural optimization (HCDstruct) tool to support transonic flutter simulations. The Enhanced Factor Correction Technique was implemented in HCDstruct to correct the Nastran doublet lattice method using data from corresponding computational fluid dynamics simulations. In this paper, sensitivities associated with this aerodynamic matching technique were investigated using HCDstruct and a Boeing 737-200-like aircraft configuration. Specifically, sensitivities of the aerodynamic matching method were investigated with respect to changes in flight conditions, such as changes in Mach number and angle of attack, and also in key design variables for the main wing, such as changes in aspect ratio and sweep angle. The variations in flight conditions and design parameters were mapped to estimated prediction error in sectional lift for the main wing, which helps to demonstrate the extent to which a user may expect a given aerodynamic correction matrix to provide suitable aerodynamic predictions for a realistic aircraft wing.

Jesse R. Quinlan↗

NASA NTRSDate not supplied

Investigation of Aerodynamic Matching Sensitivities for Conceptual Design

A methodology for aerodynamic matching was implemented in the Higher fidelity Conceptual Design and structural optimization (HCDstruct) tool to support transonic flutter simulations. The Enhanced Factor Correction Technique was implemented in HCDstruct to correct the Nastran doublet lattice method using data from corresponding computational fluid dynamics simulations. In this paper, sensitivities associated with this aerodynamic matching technique were investigated using HCDstruct and a Boeing 737-200-like aircraft configuration. Specifically, sensitivities of the aerodynamic matching method were investigated with respect to changes in flight conditions, such as changes in Mach number and angle of attack, and also in key design variables for the main wing, such as changes in aspect ratio and sweep angle. The variations in flight conditions and design parameters were mapped to estimated prediction error in sectional lift for the main wing, which helps to demonstrate the extent to which a user may expect a given aerodynamic correction matrix to provide suitable aerodynamic predictions for a realistic aircraft wing.

Jesse Ray Quinlan↗

NASA NTRSDate not supplied

Aeroacoustic Study of a Subscale Large Civil Transport (STAR) Model – Part 2: Validation of Simulated Results

Aeroacoustic measurements of the 26%-scale, semispan Boeing 777-200 Subsonic Transport Aeroacoustic Research (STAR) model tested in the NASA Ames Research Center 40- by 80-foot wind tunnel were used to ascertain the efficacy of high-fidelity simulations to accurately predict noise from the landing gear of large commercial transports. The simulations, conducted with the lattice Boltzmann solver PowerFLOW®, used a digital replica of the STAR model with or without main landing gear deployed and slats and flaps set to their highest deflection angles to represent aircraft during landing. The computations were performed at a Mach number of 0.21, Reynolds number of 8.2 million based on the model mean aerodynamic chord, and other conditions prevalent during the STAR model test. Measured and computed surface pressures were in very good agreement at most port locations on the model, as were global force coefficients, indicating that the simulations captured the impact of main gear deployment on inboard flap loading. Noise sources produced by the main landing gear and high-lift devices were determined via source localization maps generated with CLEAN from synthetic and experimental data. In general, very good agreement between predicted and measured acoustic source location and relative strength was observed in the maps. Comparisons of far-field noise spectra obtained from the CLEAN deconvolution maps showed remarkable agreement between synthetic and experimental broadband noise at low and medium frequencies. Main landing gear sources for model-scale frequencies above 7,000 Hz could not be resolved with the spatial resolution used during the simulations.

airframe noise↗

NASA NTRS1975

Design of high lift airfoils with a Stratford distribution by the Eppler method

Airfoils having a Stratford pressure distribution, which has zero skin friction in the pressure recovery area, were investigated in an effort to develop high lift airfoils. The Eppler program, an inverse conformal mapping technique where the x and y coordinates of the airfoil are developed from a given velocity distribution, was used.

Thomson, W. G.↗

NASA NTRS1976

Investigation of the use of an electronic multifunction display and an electromechanical horizontal situation indicator for guidance and control of powered-lift short-haul aircraft

The use which pilots make of a moving map display from en route through the terminal area and including the approach and go-around flight phases was investigated. The content and function of each of three primary STOLAND displays are reviewed from an operational point of view. The primary displays are the electronic attitude director indicator (EADI), the horizontal situation indicator (HSI), and the multifunction display (MFD). Manually controlled flight with both flight director guidance and raw situation data is examined in detail in a simulated flight experiment with emphasis on tracking reference flight plans and maintaining geographic orientation after missed approaches. Eye-point-of-regard and workload measurements, coupled with task performance measurements, pilot opinion ratings, and pilot comments are presented. The experimental program was designed to offer a systematic objective and subjective comparison of pilots' use of the moving map MFD in conjunction with the other displays.

Clement, W. F.↗

NASA NTRSDate not supplied

Airframe Noise Simulations of a Full-Scale Large Civil Transport in Landing Configuration

This paper summarizes the results obtained from an extensive computational campaign to accurately predict full-scale landing gear noise for large civil transports. A highly accurate digital model of a full-scale Boeing 777-300ER aircraft with as-flown nose and main landing gear components was developed for use in the simulations. Two aircraft configurations were selected: nose and main landing gear deployed with wing high-lift devices retracted, and nose and main landing gear deployed with wing high-lift devices deflected. The two configurations were simulated without and with toboggan fairings installed on the main gear to represent the principal configurations evaluated during the 2005 QTD2 flight test. All simulations were performed with the lattice Boltzmann solver PowerFLOW® to resolve and capture the highly complex, unsteady flow field in the immediate vicinity of the aircraft. The far-field noise sig-nature of the aircraft was computed via a Ffowcs-Williams and Hawkings integral approach, with flow quantities on a permeable surface enclosing the source regions used as input. Synthetic pressure records at ground array microphone locations used during the QDT2 test were employed to generate narrowband acoustic maps and integrated far-field noise spectra. With high-lift devices retracted, the predicted spectra showed that landing gear noise is equivalent to total airframe noise, with no other airframe sources appearing within 10 dB of gear peak levels. Application of a toboggan fairing to the main gear produced modest noise reductions of 1-2 dB across the resolved frequency range. With high-lift devices deflected, undercarriage noise was within 3-4 dB of the total airframe noise, thus comprising nearly half of the total airframe noise. For this configuration, the toboggan fairing did not produce a reduction in noise, corroborating trends previously observed in QTD2 flight test data.

airframe noise↗

NASA NTRS2012

Classification of Ascension Island and Natal Ozonesondes Using Self-Organizing Maps

Ozone profiles from balloon-borne ozonesondes are used for development of satellite algorithms and in chemistry-climate model initialization, assimilation and evaluation. An important issue in the application of these profiles is how best to treat variations where varying photochemical and dynamical influences can cause the ozone mixing ratio in the tropospheric segments of the profile to change by of a factor of 2-3 within a day. Clustering techniques are an ideal way to approach the statistical classification of profile data and we apply self-organizing maps to tropical tropospheric SHADOZ data, hypothesizing that the data will sort according to various influences on ozone, namely anthropogenic sources like biomass burning, meteorological conditions, and stratospheric or extra-tropical intrusions. Self-organizing maps, that use a learning algorithm to reveal the most prominent features of a data set according to a specified number of clusters, have been determined for the 1998-2009 SHADOZ profiles over Ascension Island (512 profiles, 7.98 deg. S, 14.42 deg. W) and Natal, Brazil (425 profiles, 5.42degS, 35.38degW). The 2 × 2 self-organizing map, which creates 4 clusters, reveals that deviations from the average ozone in the free troposphere include both increased ozone resulting from seasonal biomass burning in Africa and locally reduced ozone brought about by convective lifting of unpolluted boundary-layer air. Expanding to a 4 × 4 self-organizing map shows how biomass burning influences the yearly cycle of tropospheric ozone at Ascension Island and captures the seasonality of ozone at both Ascension Island and Natal. Comparing Ascension Island and Natal using a 4 × 4 self-organizing map at each site reveals similarities in mid-tropospheric ozone, but shows differences in lower-tropospheric ozone due to Ascension Island being closer to African biomass burning and more affected by descent from the mean Walker circulation, with less convective activity, than Natal.

algorithms↗

NASA NTRS2001

Flying wings / flying fuselages

The present paper has documented the historical relationships between various classes of all lifting vehicles, which includes the flying wing, all wing, tailless, lifting body, and lifting fuselage. The diversity in vehicle focus was to ensure that all vehicle types that map have contributed to or been influenced by the development of the classical flying wing concept was investigated. The paper has provided context and perspective for present and future aircraft design studies that may employ the all lifting vehicle concept. The paper also demonstrated the benefit of developing an understanding of the past in order to obtain the required knowledge to create future concepts with significantly improved aerodynamic performance.

Wood, Richard M.↗

NASA NTRSDate not supplied

Validation of the NASA Electrical Power System – Sizing and Analysis Tool (EPS-SAT)

The electrification of aircraft propulsion systems has opened the design space for engineers by allowing for unique and highly specialized propulsion system and vehicle designs. NASA developed the Electrical Power System – Sizing and Analysis Tool (EPS-SAT) to conduct high-level trade studies and sensitivity studies on the various propulsion system designs that can be implemented in electrified aircraft. The results of these studies would be used to better direct investment dollars and determine strengths and weaknesses of propulsion system designs. In this paper, the results of the EPS-SAT tool were validated with hardware data extracted from the NASA Revolutionary Vertical Lift Technology (RVLT) Advanced Reconfigurable Electric Aircraft Lab (AREAL). Updated performance maps were added to the EPS-SAT library so that high-fidelity results could be calculated.

Patrick A. Hanlon↗

NASA NTRS1983

Theoretical investigations of high lift aerodynamics

A program which generates a coordinate system for a two element airfoil with the mesh points concentrated in areas of significant vorticity, i.e., boundary layer and wake is operational. The 'imbedded' grid method developed allows a transition from the scale of the main airfoil to the scale of the flap. This requirement is essential for the modeling of viscous flows over the flap and slat of a multielement airfoil. An airfoil mounted in a 2-D wind tunnel was formulated. The program is ready for a fine grid and a large number of planes to explore the characteristics of a Navier-Stokes solver in a quasi-3D case. The program was converted to a form suitable for the STAR computer. Runs were made to map a three dimensional flow field for a wall airfoil intersection with and without lift.

Bennett, G.↗

NASA NTRS1999

STS-99 SRTM Lift and Insert into Canister

The primary objective of the STS-99 mission was to complete high resolution mapping of large sections of the Earth's surface using the Shuttle Radar Topography Mission (SRTM), a specially modified radar system. This radar system produced unrivaled 3-D images of the Earth's Surface. The mission was launched at 12:31 on February 11, 2000 onboard the space shuttle Endeavour. and led by Commander Kevin Kregel. The crew was Pilot Dominic L. Pudwill Gorie and Mission Specialists Janet L. Kavandi, Janice E. Voss, Mamoru Mohri from the National Space Development Agency (Japanese Space Agency), and Gerhard P. J. Thiele from DARA (German Space Agency). This videotape shows clean room technicians working on a part of the 200 foot long mast that will hold the SRTM in position during the mission. This videotape also shows the lowering of the SRTM into the canister.

Source record↗

NASA NTRSDate not supplied

Velocity Measurements in the Wake of the Swept Wing Flow Test Model at the National Transonic Facility

Femtosecond laser electronic excitation tagging (FLEET) was applied to obtain flowfield velocity data for the Swept Wing Flow Test (SWiFT) at the NASA Langley Research Center National Transonic Facility (NTF). Despite numerous challenges associated with performing flow velocimetry measurements within a large-scale cryogenic wind tunnel facility, the experimental campaign was conducted under various conditions, including dry air at 320 K, cool nitrogen at 240 K, and Mach numbers of 0.2 and 0.8. FLEET velocimetry measurements were performed in the downstream wake of the SWiFT model, providing a quantitative dataset. This dataset includes one-dimensional velocity profiles and two-dimensional velocity maps acquired at different angles of attack and Reynolds numbers. The two-dimensional single component velocity maps indicate relatively uniform flow across the 120-mm wide wake flow survey suggesting that the main flow features can be represented by single-position linear velocity profiles. The measured instantaneous velocity profiles at variable angles of attack are compared to model lift coefficient information obtained at Mach 0.2. At high Reynolds numbers, a sudden velocity decrease was observed in the FLEET measurements at the same time as stall in lift coefficient was observed. At a low Reynolds number, both the velocity profiles and the lift coefficient show a smoother transition, without a sudden stall. Furthermore, the two-dimensional, one component velocity map reveals a velocity deficit region at Mach 0.8 at various angles of attack. Both single shot and mean velocity measurements were acquired allowing assessment of flowfield fluctuations and measurement precisions. The uncertainties are within 4 m/s in mean measurements based on repeatability data and about 5 m/s in instantaneous single-shot measurements. Measurements are reported with ~4.8 mm spatial resolution with 32-pixel averaging used to reduce measurement errors.

femtosecond↗

NASA NTRSDate not supplied

Velocity Measurements in the Wake of the Swept Wing Flow Test (SWIFT) Model at the National Transonic Facility

Femtosecond laser electronic excitation tagging (FLEET) was applied to obtain flowfield velocity data for the Swept Wing Flow Test (SWiFT) at the NASA Langley Research Center National Transonic Facility (NTF). Despite numerous challenges associated with performing flow velocimetry measurements within a large-scale cryogenic wind tunnel facility, the experimental campaign was conducted under various conditions, including dry air at 320 K, cool nitrogen at 240 K, and Mach numbers of 0.2 and 0.8. FLEET velocimetry measurements were performed in the downstream wake of the SWiFT model, providing a quantitative dataset. This dataset includes one-dimensional velocity profiles and two-dimensional velocity maps acquired at different angles of attack and Reynolds numbers. The two-dimensional single component velocity maps indicate relatively uniform flow across the 120-mm wide wake flow survey suggesting that the main flow features can be represented by single-position linear velocity profiles. The measured instantaneous velocity profiles at variable angles of attack are compared to model lift coefficient information obtained at Mach 0.2. At high Reynolds numbers, a sudden velocity decrease was observed in the FLEET measurements at the same time as stall in lift coefficient was observed. At a low Reynolds number, both the velocity profiles and the lift coefficient show a smoother transition, without a sudden stall. Furthermore, the two-dimensional, one component velocity map reveals a velocity deficit region at Mach 0.8 at various angles of attack. Both single shot and mean velocity measurements were acquired allowing assessment of flowfield fluctuations and measurement precisions. The uncertainties are within 4 m/s in mean measurements based on repeatability data and about 5 m/s in instantaneous single-shot measurements. Measurements are reported with ~4.8 mm spatial resolution with 32-pixel averaging used to reduce measurement errors.

Transonic↗