Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LiBH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Ionic conductivity and the formation of cubic CaH{sub 2} in the LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composite

LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composites were prepared by ball milling. Their crystal structures and phase composition were investigated using synchrotron X-ray diffraction and Rietveld refinement, and their ionic conductivity was measured using impedance spectroscopy. The materials were found to form a physical mixture. The composites were composed of α-Ca(BH{sub 4}){sub 2}, γ-Ca(BH{sub 4}){sub 2} and orthorhombic LiBH{sub 4}, and the relative phase quantities of the Ca(BH{sub 4}){sub 2} polymorphs varied significantly with LiBH{sub 4} content. The formation of small amounts of orthorhombic CaH{sub 2} and cubic CaH{sub 2} in a CaF{sub 2}-like structure was observed upon heat treatment. Concurrent formation of elemental boron may also occur. The ionic conductivity of the composites was measured using impedance spectroscopy, and was found to be lower than that of ball milled LiBH{sub 4}. Electronic band structure calculations indicate that cubic CaH{sub 2} with hydrogen defects is electronically conducting. Its formation along with the possible precipitation of boron therefore has an effect on the measured conductivity of the LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composites and may increase the risk of an internal short-circuit in the cells. -- Graphical abstract: An Arrhenius plot of the ionic conductivity of the LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composites (red, blue, green). The ionic conductivity of ball milled (gray) and non-milled (black) LiBH{sub 4} is shown for comparison. The filled symbols are measured during heating runs and the empty symbols are measured during subsequent cooling runs. The conductivity of the composites is in all cases higher during cooling, most probably due to the formation of an electronically conducting layer containing defect-rich cubic CaH{sub 2}. Such layer formation could eventually lead to a short circuit in the cell and reveals a general issue of chemical stability that should be attended to in the development of solid electrolyte materials. Highlights: • The LiBH{sub 4}–Ca(BH{sub 4}){sub 2} composite forms a physical mixture rather than a solid solution. • The formation of defect-rich, cubic CaH{sub 2} in a CaF{sub 2}-like structure is observed. • A new layer containing cubic CaH{sub 2} is conducting and may lead to a short-circuit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of MoS{sub 2} on hydrogenation storage properties of LiBH{sub 4}

The hydrogen storage properties of LiBH{sub 4} ball milled with 20 wt% MoS{sub 2} have been investigated. It shows that the LiBH{sub 4} doped with MoS{sub 2} exhibits favorable hydrogenation and dehydrogenation properties in terms of decomposition temperature and hydriding/dehydriding reversibility. The sample with MoS{sub 2} starts to release hydrogen at 230 °C and has a decrease of 80 °C in contrast with pristine LiBH{sub 4}. Furthermore, for the second cycle, the LiBH{sub 4} with MoS{sub 2} maintains a reversible hydrogen storage capacity of about 8.0 wt% which is almost identical with the first cycle under 5 MPa at 550 °C. Analyzed by the XRD and the FTIR results, LiBH{sub 4} can be regenerated after re-hydrogenation under a relatively mild condition by adding MoS{sub 2}. The improvement of the hydrogenation and dehydrogenation properties mainly results from the formation of Li{sub 2}S and MoB{sub 2} during ball milling. -- Graphical abstract: Hydrogen absorption curves of LiBH{sub 4} doped with MoS{sub 2} for five cycles at 400 °C. Highlights: • The hydrogen absorption capacity is nearly the same for 5 cycles at 400 °C. • The sample with MoS{sub 2} starts to release hydrogen at 230 °C. • The coexistence of MoB{sub 2} and Li{sub 2}S catalyzes the decomposition of LiBH{sub 4}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preparation of MgH{sub 2} composite with a composition of 40%MgH{sub 2} + 30%LiBH{sub 4} + 30%(2LiBH{sub 4} + MgF{sub 2})

Graphical abstract: Hydrogen content vs. desorption time curves for consecutive 1st desorptions of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) at 533–873 K. Highlights: ► Addition of MgF{sub 2} and LiBH{sub 4} with a higher hydrogen storage capacity to MgH{sub 2}. ► Preparation of 40%MgH{sub 2} + 30%LiBH{sub 4} + 30% (2LiBH{sub 4} + MgF{sub 2}) composite. ► Examination of desorption properties of the composite. ► Total desorbed hydrogen quantity for consecutive 1st desorptions of 7.07 wt%. ► Reactions of LiBH{sub 4} → LiH + B + (3/2)H{sub 2}, and 2LiBH{sub 4} + MgF{sub 2} → 2LiF + MgB{sub 2} + 4H{sub 2}. -- Abstract: A mixture of containing two chemical equivalents of lithium borohyride and one equivalent of magnesium fluoride is known to yield hydrogen in an amount of about 7.6 wt% of the mixture when heated to about 150 °C at atmospheric pressure by the following reaction; 2LiBH{sub 4} + MgF{sub 2} = 2LiF + MgB{sub 2} + 4H{sub 2}. In order to increase hydrogen storage capacity of Mg-based materials, a mixture with a composition of 2LiBH{sub 4} + MgF{sub 2} and LiBH{sub 4}with a higher hydrogen storage capacity of 18.4 wt% were added to MgH{sub 2}. MgH{sub 2} composite with a composition of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) was prepared by reactive mechanical grinding. The hydrogen storage properties of the sample were then examined. Hydrogen content vs. desorption time curves for consecutive 1st desorptions of 40 wt%MgH{sub 2} + 30 wt%LiBH{sub 4} + 30 wt%(2LiBH{sub 4} + MgF{sub 2}) at 533–873 K showed that the total desorbed hydrogen quantity for consecutive 1st desorptions is 7.07 wt%.

36 MATERIALS SCIENCE↗

Stability and conductivity of cation- and anion-substituted LiBH 4 -based solid-state electrolytes

The high-temperature phase of LiBH 4 (HT-LiBH 4 ) exhibits a promisingly high lithium ion conductivity but is unstable at room temperature. We use density functional theory (DFT) calculations to investigate the stabilization effect of halogen and alkali cation/anion substitutions on HT-LiBH 4 as well the underlying mechanism for the high lithium ion conductivity. We find that increasing the substituent concentration enhances the stabilization of HT-LiBH 4 (i.e., the DFT energy difference between the low- and high-temperature forms of substituted LiBH 4 is reduced). Cation/anion substitution also leads to a higher Li defect (vacancy, interstitial, and Frenkel) formation energy, thereby reducing the Li defect (vacancy, interstitial, and Frenkel) concentrations. Using DFT migration barriers input into kinetic Monte Carlo simulations and the Materials INTerface (MINT) framework, here we calculate the room-temperature lithium ion conductivities for Li(BH 4 ) 1-x I x (x = 0.25 and 0.5) and Li 1-y K y BH 4 (y = 0.25). Our calculations suggest that the lower I concentration leads to a higher lithium ion conductivity of 5.7 x10 -3 S/cm compared with that of Li(BH 4 ) 0.5 I 0.5 (4.2 ×10 -5 S/cm) because of the formation of more Li-related defects. Based on our findings, we suggest that the stabilization of HT-LiBH 4 -based lithium ion conductors can be controlled by carefully tuning the cation/anion substituent concentrations to maximize the lithium ionic conductivities of the specific system.

36 MATERIALS SCIENCE↗

First-principles calculated decomposition pathways for LiBH 4 nanoclusters

Here, we analyze thermodynamic stability and decomposition pathways of LiBH 4 nanoclusters using grand-canonical free-energy minimization based on total energies and vibrational frequencies obtained from density-functional theory (DFT) calculations. We consider (LiBH 4 ) n nanoclusters with n = 2 to 12 as reactants, while the possible products include (Li) n , (B) n , (LiB) n , (LiH) n , and Li 2 B n H n ; off-stoichiometric LinBnHm (m ≤ 4n) clusters were considered for n = 2, 3, and 6. Cluster ground-state configurations have been predicted using prototype electrostatic ground-state (PEGS) and genetic algorithm (GA) based structural optimizations. Free-energy calculations show hydrogen release pathways markedly differ from those in bulk LiBH 4 . While experiments have found that the bulk material decomposes into LiH and B, with Li 2 B 12 H 12 as a kinetically inhibited intermediate phase, (LiBH 4 ) n nanoclusters with n ≤ 12 are predicted to decompose into mixed Li n B n clusters via a series of intermediate clusters of Li n B n H m (m ≤ 4n). The calculated pressure-composition isotherms and temperature-pressure isobars exhibit sloping plateaus due to finite size effects on reaction thermodynamics. Generally, decomposition temperatures of free-standing clusters are found to increase with decreasing cluster size due to thermodynamic destabilization of reaction products.

36 MATERIALS SCIENCE↗

Development of bulk-type all-solid-state lithium-sulfur battery using LiBH{sub 4} electrolyte

Stable battery operation of a bulk-type all-solid-state lithium-sulfur battery was demonstrated by using a LiBH{sub 4} electrolyte. The electrochemical activity of insulating elemental sulfur as the positive electrode was enhanced by the mutual dispersion of elemental sulfur and carbon in the composite powders. Subsequently, a tight interface between the sulfur-carbon composite and the LiBH{sub 4} powders was manifested only by cold-pressing owing to the highly deformable nature of the LiBH{sub 4} electrolyte. The high reducing ability of LiBH{sub 4} allows using the use of a Li negative electrode that enhances the energy density. The results demonstrate the interface modification of insulating sulfur and the architecture of an all-solid-state Li-S battery configuration with high energy density.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Hydriding and dehydriding characteristics of LiBH{sub 4} and transition metals-added magnesium hydride

Graphical abstract: Hydriding reaction curves under 12 bar H{sub 2}, and dehydriding reaction curves under 1.0 bar H{sub 2}, at 593 K at the 1st cycle for MgH{sub 2}–10Ni–2LiBH{sub 4}–2Ti and MgH{sub 2}. Highlights: ► Addition of Ni, LiBH{sub 4}, and Ti to MgH{sub 2} to increase reaction rates. ► Sample preparation by reactive mechanical grinding. ► At n = 2, the sample absorbed 4.05 wt% H for 60 min at 593 K under 12 bar H{sub 2}. ► Analysis of rate-controlling step for dehydriding of the sample at n = 3. - Abstract: In this study, MgH{sub 2} was used as a starting material instead of Mg. Ni, Ti, and LiBH{sub 4} with a high hydrogen-storage capacity of 18.4 wt% were added. A sample with a composition of MgH{sub 2}–10Ni–2LiBH{sub 4}–2Ti was prepared by reactive mechanical grinding. The activation of MgH{sub 2}–10Ni–2LiBH{sub 4}–2Ti was completed after the first hydriding–dehydrding cycle. The hydriding rate decreases as the temperature increases due to the decrease in the driving force for the hydriding reaction. At the 1st cycle, the sample desorbs 1.45 wt% H for 10 min, 2.54 wt% H for 20 min, 3.13 wt% H for 30 min, and 3.40 wt% H for 60 min at 593 K under 1.0 bar H{sub 2}. At the 2nd cycle, the sample absorbs 3.84 wt% H for 5 min, 3.96 wt% H for 10 min, and 4.05 wt% H for 60 min at 593 K under 12 bar H{sub 2}. MgH{sub 2}–10Ni–2LiBH{sub 4}–2Ti after reactive mechanical grinding contained MgH{sub 2}, Mg, Ni, TiH{sub 1.924}, and MgO phases. The reactive mechanical grinding of Mg with Ni, LiBH{sub 4}, and Ti is considered to create defects on the surface and in the interior of Mg (to facilitate nucleation), and to reduce the particle size of Mg (to shorten diffusion distances of hydrogen atoms). The formation of Mg{sub 2}Ni during hydriding–dehydriding cycling increases the hydriding and dehydriding rates of the sample.

36 MATERIALS SCIENCE↗

Mechanochemistry of the LiBH 4 –AlCl 3 System: Structural Characterization of the Products by Solid-State NMR

The double-cation metal borohydride, Li 4 Al 3 (BH 4 ) 13 , mechanochemically produced from a 13:3 mixture of lithium borohydride (LiBH 4 ) and aluminum chloride (AlCl 3 ), has a low hydrogen desorption temperature; however, the material’s decomposition is accompanied by a large emission of toxic diborane (B 2 H 6 ). In this study, we found that a decrease of the LiBH 4 :AlCl 3 ratio in the starting mixture yields increased amounts of partially chlorinated products that also dehydrogenate at low temperature, but release negligibly small amounts of diborane. Extensive characterization by solid-state NMR spectroscopy (SSNMR) and powder X-ray diffraction (XRD) found that the 11:3 ratio product maintains the Li 4 Al 3 (BH 4 ) 13- like structure, with additional Cl – anions substituting for [BH 4 ] – compared to the 13:3 mixture. Further decrease of relative LiBH 4 concentration in the starting mixture to 9:3 results in a different product composed of tetrahedral [Al(BH 4 ) 4 ] - and [Al(BH 4 ) 2 Cl 2 ] - complexes, in which two hydrogen atoms of each borohydride group are bridged to aluminum sites. Additionally, SSNMR revealed the covalent character of the Al–H bonds, which is not observed in Li 4 Al 3 (BH 4 ) 13 . In conclusion, these findings suggest that the Al–Cl bonding present in the chlorinated complexes prevents the formation of Al(BH 4 ) 3 , which is a known intermediate leading to the formation of diborane during thermal dehydrogenation of the nearly chlorine-free Li 4 Al 3 (BH 4 ) 13 .

36 MATERIALS SCIENCE↗

Reversible Hydrogen Storage in a LiBH 4 –C 60 Nanocomposite

Reversible hydrogen storage in a LiBH 4 :C 60 nanocomposite (70:30 wt. %) synthesized by solvent-assisted mixing has been demonstrated. During the solvent-assisted mixing and nanocomposite formation, a chemical reaction occurs in which the C 60 cages are significantly modified by polymerization as well as by hydrogenation (fullerane formation) in the presence of LiBH{sub 4}. We have determined that two distinct hydrogen desorption events are observed upon rehydrogenation of the material, which are attributed to the reversible formation of a fullerane (C 60 H x ) as well as a LiBH4 species. This system is unique in that the carbon species (C 60 ) actively participates in the hydrogen storage process which differs from the common practice of melt infiltration of high surface area carbon materials with LiBH 4 (nanoconfinment effect). This nanocomposite demonstrated good reversible hydrogen storage properties as well as the ability to absorb hydrogen under mild conditions (pressures as low as 10 bar H 2 or temperatures as low as 150°C). The nanocomposite was characterized by TGA-RGA, DSC, XRD, LDI-TOF-MS, FTIR, 1H NMR, and APPI MS.

08 HYDROGEN↗

Biased interface between solid ion conductor LiBH{sub 4} and lithium metal: A first principles molecular dynamics study

We use first-principles molecular dynamics to study the electrochemical solid-solid interface between lithium metal and lithium electrolyte LiBH{sub 4}. An external bias is applied by using an effective screening medium. We observe large polarization in the LiBH{sub 4}, because the lithium cations in LiBH{sub 4} are shifted more on one side of the double-well potential of Li{sup +}. This results in a large potential drop in the interface region and a large double-layer capacity corresponding to ca. 70 μF/cm{sup 2}. H-coordination to the Li atoms plays an important role in the charge-transfer reaction and ion transfer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Materials Data on LiBH by Materials Project

LiBH crystallizes in the orthorhombic Pnma space group. The structure is two-dimensional and consists of two LiBH sheets oriented in the (0, 1, 0) direction. Li is bonded in a 3-coordinate geometry to three equivalent H atoms. There are two shorter (1.94 Å) and one longer (2.07 Å) Li–H bond lengths. B is bonded in a distorted single-bond geometry to one H atom. The B–H bond length is 1.28 Å. H is bonded to three equivalent Li and one B atom to form corner-sharing HLi3B trigonal pyramids.

36 MATERIALS SCIENCE↗

Nuclear magnetic resonance study of Li and H diffusion in the high-temperature solid phase of LiBH{sub 4}

In order to study the atomic jump motions in the high-temperature solid phase of LiBH{sub 4}, we have measured the {sup 1}H and {sup 11}B nuclear magnetic resonance (NMR) spectra and the {sup 1}H, {sup 7}Li and {sup 11}B spin-lattice relaxation rates in this compound over the resonance frequency range of 14-34.4 MHz. In the temperature range 384-500 K, all the spin-lattice relaxation data are satisfactorily described in terms of a thermally activated jump motion of Li ions with the pre-exponential factor tau{sub 0}=1.1x10{sup -15} s and the activation energy E{sub a}=0.56 eV. The observed frequency dependences of the spin-lattice relaxation rates in this temperature range exclude a presence of any distributions of the Li jump rate or any other jump processes on the frequency scale of 10{sup 7}-10{sup 10} s{sup -1}. The strong narrowing of the {sup 1}H and {sup 11}B NMR lines above 440 K is consistent with the onset of diffusive motion of the BH{sub 4} tetrahedra. - Graphical abstract: The measured spin-lattice relaxation rates of {sup 1}H (a), {sup 7}Li (b) and {sup 11}B (c) as functions of the inverse temperature for the high-temperature solid phase of LiBH{sub 4}. The curves show the simultaneous Bloembergen-Purcell-Pound fits to the data with the fixed parameters of Li diffusion (the pre-exponential factor tau{sub 0}=1.1x10{sup -15} s and the activation energy E{sub a}=0.56 eV). This plot indicates that all the relaxation data for different nuclei and at different resonance frequencies are governed by a single Li jump process. Display Omitted

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure and Dynamics for LiBH4-LiCl Solid Solutions

A surprisingly high degree of structural and compositional dynamics is observed in the system LiBH{sub 4}-LiCl as a function of temperature and time. Rietveld refinement of synchrotron radiation powder X-ray diffraction (SR-PXD) data reveals that Cl{sup -} readily substitutes for BH{sub 4}{sup -} in the structure of LiBH{sub 4}. Prolonged heating a sample of LiBH{sub 4}-LiCl (1:1 molar ratio) above the phase transition temperature and below the melting point (108 < T < 275 C) can produce highly chloride substituted hexagonal lithium borohydride, h-Li(BH{sub 4}){sub 1-x}Cl{sub x}, e.g., x {approx} 0.42, after heating from room temperature (RT) to 224 C at 2.5 C/min. LiCl has a higher solubility in h-LiBH{sub 4} as compared to orthorhombic lithium borohydride, o-LiBH{sub 4}, which is illustrated by a LiBH{sub 4}-LiCl (1:1) sample equilibrated at 245 C for 24 days and left at RT for another 13 months. Rietveld refinement reveals that this sample contains o-Li(BH{sub 4}){sub 0.91}Cl{sub 0.09} and LiCl. This illustrates a significantly faster dissolution of LiCl in h-LiBH{sub 4} as compared to a slower segregation of LiCl from o-LiBH{sub 4}, which is also demonstrated by in situ SR-PXD from three cycles of heating and cooling of the same Li(BH{sub 4}){sub 0.91}Cl{sub 0.09} sample. The substitution of the smaller Cl{sup -} for the larger BH{sub 4}{sup -} ion is clearly observed as a reduction in the unit cell volume as a function of time and temperature. A significant stabilization of h-LiBH{sub 4} is found to depend on the degree of anion substitution. Variable temperature solid-state magic-angle spinning (MAS) {sup 7}Li and {sup 11}B NMR experiments on pure LiBH{sub 4} show an increase in full width at half maximum (fwhm) when approaching the phase transition from o- to h-LiBH{sub 4}, which indicates an increase of the relaxation rate (i.e., T{sub 2} decreases). A less pronounced effect is observed for ion-substituted Li(BH{sub 4}){sub 1-x}Cl{sub x}, 0.09 < x < 0.42. The MAS NMR experiments also demonstrate a higher degree of motion in the hexagonal phase, i.e., fwhm is reduced by more than a factor of 10 at the o- to h-LiBH{sub 4} phase transition.

36 MATERIALS SCIENCE↗

Synthesis of rock-salt type lithium borohydride and its peculiar Li{sup +} ion conduction properties

The high energy density and excellent cycle performance of lithium ion batteries makes them superior to all other secondary batteries and explains why they are widely used in portable devices. However, because organic liquid electrolytes have a higher operating voltage than aqueous solution, they are used in lithium ion batteries. This comes with the risk of fire due to their flammability. Solid electrolytes are being investigated to find an alternative to organic liquid. However, the nature of the solid-solid point contact at the interface between the electrolyte and electrode or between the electrolyte grains is such that high power density has proven difficult to attain. We develop a new method for the fabrication of a solid electrolyte using LiBH{sub 4,} known for its super Li{sup +} ion conduction without any grain boundary contribution. The modifications to the conduction pathway achieved by stabilizing the high pressure form of this material provided a new structure with some LiBH{sub 4}, more suitable to the high rate condition. We synthesized the H.P. form of LiBH{sub 4} under ambient pressure by doping LiBH{sub 4} with the KI lattice by sintering. The formation of a KI - LiBH{sub 4} solid solution was confirmed both macroscopically and microscopically. The obtained sample was shown to be a pure Li{sup +} conductor despite its small Li{sup +} content. This conduction mechanism, where the light doping cation played a major role in ion conduction, was termed the “Parasitic Conduction Mechanism.” This mechanism made it possible to synthesize a new ion conductor and is expected to have enormous potential in the search for new battery materials.

36 MATERIALS SCIENCE↗

Solid state electrolyte composites based on complex hydrides and metal doped fullerenes/fulleranes for batteries and electrochemical applications

A LiBH 4 --C 60 nanocomposite that displays fast lithium ionic conduction in the solid state is provided. The material is a homogenous nanocomposite that contains both LiBH 4 and a hydrogenated fullerene species. In the presence of C 60 , the lithium ion mobility of LiBH 4 is significantly enhanced in the as prepared state when compared to pure LiBH 4 . After the material is annealed the lithium ion mobility is further enhanced. Constant current cycling demonstrated that the material is stable in the presence of metallic lithium electrodes. The material can serve as a solid state electrolyte in a solid-state lithium ion battery.

25 ENERGY STORAGE↗