Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LIMESTONE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Direct in-situ observation of early age void evolution in sustainable cement paste containing fly ash or limestone

This paper uses fast X-ray Computed Tomography (fCT) to study the change in air-filled voids during hydration of portland cement pastes of different water to cement ratios and with fly ash and limestone additives between 30 min and 12 h of hydration with deionized and de-aired water. For the deionized samples, the total volume of the air-filled voids increased during the induction period and decreased as the acceleration period began and finally stayed constant. The samples with 20% replacement of fly ash and 20% replacement of limestone showed the same trends as the OPC samples but with a reduction in the observed air-filled void formation. The air-filled void distribution in these samples changed from a limited number of large voids at the beginning of the measurements to a system with a significantly greater number of uniformly distributed smaller voids. The changes in the air-filled voids were not significant in pastes made with 50% fly ash or with de-aired water in the same testing condition. This might be explained by differences in pore solution chemistry and a reduced amount of dissolved air in the mixing water. A mechanism is proposed for a change in ionic concentration in solution to cause release of the dissolved air within the mixing water.

Cement hydration↗

Limestone calcination with CO{sub 2} capture (III): characteristics of coal combustion during limestone decomposition

In this study, the combustion characteristics of coal in CO{sub 2}/O{sub 2} and steam/CO{sub 2}/O{sub 2} atmospheres were investigated during limestone decomposition in a continuously operating fluidized bed reactor for CO{sub 2} capture. The results show that the variations and concentrations of CO, CH{sub 4}, and H{sub 2} in the exhaust gas of the reactor in the steam/CO{sub 2}/O{sub 2} atmosphere were smaller than those in the CO{sub 2}/O{sub 2} atmosphere. Because of steam dilution, the CO{sub 2} concentration in the bed was lower in the steam/CO{sub 2}/O{sub 2} atmosphere than that in the CO{sub 2}/O{sub 2} atmosphere, and the effect of differential pressure variation on limestone decomposition in the fluidized bed was less pronounced in the steam/CO{sub 2}/O{sub 2} atmosphere than that in the CO{sub 2}/O{sub 2} atmosphere. Additionally, N{sub 2}O emission was detected only in the CO{sub 2}/O{sub 2} atmosphere, and the conversion of N to NO in the steam dilution atmosphere was of a smaller magnitude than that observed in the CO{sub 2}/O{sub 2} atmosphere. We also found that the conversion of S to SO{sub 2} in the steam/CO{sub 2}/O{sub 2} atmosphere was lower than that observed in the CO{sub 2}/O{sub 2} atmosphere. The contents of sulfur, SiO{sub 2}, and Al{sub 2}O{sub 3} were much higher in solid samples located in the cyclone than in the overflow holder in both steam/CO{sub 2}/O{sub 2} and CO{sub 2}/O{sub 2} atmospheres. Finally, the hydration and carbonation reactivities of CaO produced in the steam/CO{sub 2}/O{sub 2} atmosphere were better than those produced in the CO{sub 2}/O{sub 2} atmosphere. 13 refs., 14 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Towards ternary binders involving limestone additions — A review

The review summarises literature to examine the transition from portland limestone cement system to composite ternary binder systems involving limestone. Interest in limestone addition as an ideal component in multicomponent binder systems has surged as evident from the large volume of literature published in the recent past. A ternary blended system, with co-substitution of limestone, has the potential to complement the reaction of the supplementary cementitious materials (SCMs). The direct addition of limestone powder helps to attain higher substitution levels of portland cement clinker, improve early age properties, and supplement SCM's reactivity. However, the dilution of hydrates could hamper the long-term benefits. In this review, the interaction of fine limestone is classified and elaborated under two broad umbrellas: physical and chemical interactions. The physical interactions can manifest in three ways, namely, filler action, shearing action and improved packing, which alters reaction rate and extent at early ages. The chemical interactions also modify the reaction kinetics and phase assemblage due to nucleation of C-S-H on calcite surfaces, preservation of the ettringite phase and formation of carboaluminates. Two different forms of carboaluminate hydrates — hemicarboaluminate and mono-carboaluminate can be present in the hydrate matrix depending on the balance between carbonate ions and aluminates in the pore solution. Several factors such as replacement level, particle size, choice of SCM, its reactivity and reactive aluminates content, sulphate levels, curing temperature, and duration of curing can control the carboaluminate formation, reaction degree of SCMs and chemical interaction from limestone additions. A combination of physical and chemical effects makes fine limestone a potential material for co-substitution with aluminosilicate based SCMs, mainly fly ash, slag, and calcined clay. In this review, the factors affecting limestone-SCM composites are summarised based on a detailed literature survey. The effects of SCM-limestone cement composites on hydration kinetics, reaction chemistry, the reactivity of SCMs, the stability of hydrated phases, and contribution to the physical structure development and macroscopic properties by evaluating hydration and mechanical properties are discussed. The importance of AFm (Al{sub 2}O{sub 3}–Fe{sub 2}O{sub 3}-mono) phases in various deterioration mechanisms in concrete and their influence on performance characteristics in different exposure environment is critically appraised.

36 MATERIALS SCIENCE↗

Influence of microstructure on replacement and porosity generation during experimental dolomitization of limestones

Replacement reactions commonly alter the multiscale pore structures of rocks during fluid-rock interactions. Analysis of these processes in various model fluid-rock systems during controlled laboratory experiments provides insights into the origins of microstructures found in natural materials. This study focused on understanding the effects of initial starting material permeability and resultant differences in transport pathways on porosity and mineralogical changes during limestone dolomitization.A series of replacement experiments (32–317 days in duration) have been conducted in which 1.59 cm (5/8 in.) diameter cores of two different limestones were reacted with saturated MgCl2 solutions at 200 °C. The Texas Cream (Austin Chalk) is a high-porosity, high-permeability limestone, whereas both the porosity and permeability of the Carthage Marble (Burlington Limestone) are relatively low. Altered limestones were imaged using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Time-of-Flight Secondary Ion Mass Spectrometry (ToF–SIMS) and electron microprobe analysis (EMPA). A representative grain boundary of the low-porosity limestone was targeted for a focused ion beam (FIB) lift-out and characterized using transmission electron microscopy (TEM). These results were coupled with analyses of radial changes in the porosity distribution of the core derived from X-ray and neutron small- and ultra-small angle scattering ((U)SANS/(U)SAXS).The high-porosity/permeability limestone showed a four times faster bulk replacement rate than the lower-porosity/permeability material, and a different mechanism of porosity development. For the low-porosity limestone, a two-stage replacement occurred, with the reacted region of the core consisting of an inner rim in which the limestone was replaced by two calcite-dolomite solid solutions, and an outer rim in which the dolomite was replaced by magnesite. Elongated pores formed along grain boundaries at the initial limestone/dolomite reaction interface, and additional nanometer-scale porosity was formed at the secondary magnesite replacement rim. Grain boundaries were identified as preferential pathways for transport leading to dolomitization and a grain boundary diffusion rate was calculated based on microstructural characterization. In contrast, replacement in the high-porosity limestone was accompanied by porosity generation through replacement of individual grains by dolomite throughout the sample and, in longer runs, magnesite in outer parts of the core. These observations emphasize that both the mechanisms of the replacement reaction and the microstructure and chemistry of the replaced product are contingent on the initial structure of the starting material.

36 MATERIALS SCIENCE↗

{sup 13}C chemical shift anisotropies for carbonate ions in cement minerals and the use of {sup 13}C, {sup 27}Al and {sup 29}Si MAS NMR in studies of Portland cement including limestone additions

{sup 13}C isotropic chemical shifts and chemical shift anisotropy parameters have been determined for a number of inorganic carbonates relevant in cement chemistry from slow-speed {sup 13}C MAS or {sup 13}C({sup 1}H) CP/MAS NMR spectra (9.4 T or 14.1 T) for {sup 13}C in natural abundance. The variation in the {sup 13}C chemical shift parameters is relatively small, raising some doubts that different carbonate species in Portland cement-based materials may not be sufficiently resolved in {sup 13}C MAS NMR spectra. However, it is shown that by combining {sup 13}C MAS and {sup 13}C({sup 1}H) CP/MAS NMR carbonate anions in anhydrous and hydrated phases can be distinguished, thereby providing valuable information about the reactivity of limestone in cement blends. This is illustrated for three cement pastes prepared from an ordinary Portland cement, including 0, 16, and 25 wt.% limestone, and following the hydration for up to one year. For these blends {sup 29}Si MAS NMR reveals that the limestone filler accelerates the hydration for alite and also results in a smaller fraction of tetrahedrally coordinated Al incorporated in the C-S-H phase. The latter result is more clearly observed in {sup 27}Al MAS NMR spectra of the cement–limestone blends and suggests that dissolved aluminate species in the cement–limestone blends readily react with carbonate ions from the limestone filler, forming calcium monocarboaluminate hydrate. -- Highlights: •{sup 13}C chemical shift anisotropies for inorganic carbonates from {sup 13}C MAS NMR. •Narrow {sup 13}C NMR chemical shift range (163–171 ppm) for inorganic carbonates. •Anhydrous and hydrated carbonate species by {sup 13}C MAS and {sup 13}C({sup 1}H) CP/MAS NMR. •Limestone accelerates the hydration for alite in Portland – limestone cements. •Limestone reduces the amount of aluminium incorporated in the C-S-H phase.

36 MATERIALS SCIENCE↗

3D mapping of water in oolithic limestone at atmospheric and vacuum saturation using X-ray micro-CT differential imaging

Determining the distribution of fluids in porous sedimentary rocks is of great importance in many geological fields. However, this is not straightforward, especially in the case of complex sedimentary rocks like limestone, where a multidisciplinary approach is often needed to capture its broad, multimodal pore size distribution and complex pore geometries. This paper focuses on the porosity and fluid distribution in two varieties of Massangis limestone, a widely used natural building stone from the southeast part of the Paris basin (France). The Massangis limestone shows locally varying post-depositional alterations, resulting in different types of pore networks and very different water distributions within the limestone. Traditional techniques for characterizing the porosity and pore size distribution are compared with state-of-the-art neutron radiography and X-ray computed microtomography to visualize the distribution of water inside the limestone at different imbibition conditions. X-ray computed microtomography images have the great advantage to non-destructively visualize and analyze the pore space inside of a rock, but are often limited to the larger macropores in the rock due to resolution limitations. In this paper, differential imaging is successfully applied to the X-ray computed microtomography images to obtain sub-resolution information about fluid occupancy and to map the fluid distribution in three dimensions inside the scanned limestone samples. The detailed study of the pore space with differential imaging allows understanding the difference in the water uptake behavior of the limestone, a primary factor that affects the weathering of the rock. - Highlights: • The water distribution in a limestone was visualized in 3D with micro-CT. • Differential imaging allowed to map both macro and microporous zones in the rock. • The 3D study of the pore space clarified the difference in water uptake behavior. • Trapped air is visualized in the moldic macropores at atmospheric saturation.

36 MATERIALS SCIENCE↗

Impact of limestone fineness on cement hydration at early age

This study compares the influence of two limestone fineness on strength development and cement hydration. The replacement of clinker by 20% of fine limestone (d{sub v,50} = 2 μm and SSA = 4,21 m{sup 2}/g) gives similar strength development to PC up to 7 days. Fine limestone enhances cement hydration and offsets the dilution effect caused by the decrease of clinker amount. The accelerating effect of the limestone was explained by a higher degree of undersaturation with respect to C{sub 3}S. The influence of coarse limestone (d{sub v,50} = 130 μm and SSA = 0,46 m{sup 2}/g) on cement hydration is limited to dilution effect. The combination of fine and coarse limestone was also studied. A linear correlation was obtained between strength and gel space ratio for all investigated systems. Furthermore, the results showed that despite the similarity of specific surface area, limestone is more effective than quartz for the enhancement of cement hydration.

36 MATERIALS SCIENCE↗

Microstructural characterization of limestone exposed to heat with XRD, SEM and TG-DSC

Highlights: • The microstructure of limestone (25 °C–800 °C) was analyzed by XRD, SEM and TG-DSC. • The microstructural properties of the crystal are anisotropic in different crystal plane directions. • Microstructure controls the macroscopic properties of limestone. - Abstract: Limestone is a common rock used in many buildings and found in underground engineering projects. After exposure to heat, for example, the occurrence of fires, the stability of limestone structures is mostly affected, which may have safety repercussions. Therefore, the impact of thermal effects on the microstructure of limestone is investigated in this study, in which 8 groups of limestone samples are exposed to different temperatures (25 °C, 100 °C, 200 °C, 300 °C, 500 °C, 600 °C, 700 °C and 800 °C), after which X-ray diffraction, differential scanning calorimetry and scanning electron microscopy are carried out. The mineral composition and the microstructure of the samples are numerically modeled, in which the diffraction peaks, full width at half maximum, integral breadth, microstrain, average domain size and dislocation density are analyzed. The macroscopic properties obtained from the results in other works in the literature including porosity, compressive strength, damage coefficients and modulus of elasticity are also compared with the parameters above. The changes in the crystal structure of two minerals, calcite and dolomite, are found to be anisotropic in the different crystal plane directions. It is also found that the limestone microstructure affects the macroscopic properties. A temperature between 200 °C to 300 °C is the critical temperature at which both the macroscopic properties and macrostructure demonstrate significant changes.

36 MATERIALS SCIENCE↗

Influence of limestone on the hydration of Portland cements

The influence of the presence of limestone on the hydration of Portland cement was investigated. Blending of Portland cement with limestone was found to influence the hydrate assemblage of the hydrated cement. Thermodynamic calculations as well as experimental observations indicated that in the presence of limestone, monocarbonate instead of monosulfate was stable. Thermodynamic modelling showed that the stabilisation of monocarbonate in the presence of limestone indirectly stabilised ettringite leading to a corresponding increase of the total volume of the hydrate phase and a decrease of porosity. The measured difference in porosity between the 'limestone-free' cement, which contained less than 0.3% CO{sub 2}, and a cement containing 4% limestone, however, was much smaller than calculated. Coupling of thermodynamic modelling with a set of kinetic equations which described the dissolution of the clinker, predicted quantitatively the amount of hydrates. The quantities of ettringite, portlandite and amorphous phase as determined by TGA and XRD agreed well with the calculated amounts of these phases after different periods of time. The findings in this paper show that changes in the bulk composition of hydrating cements can be followed by coupled thermodynamic models. Comparison between experimental and modelled data helps to understand in more detail the dominating processes during cement hydration.

36 MATERIALS SCIENCE↗

Direct sulfation of limestone based on oxy-fuel combustion technology

With limestone as the sorbent, the sulfation reaction can proceed via two different routes depending on whether calcination of the limestone takes place under the given reaction conditions. The direct sulfation reaction is defined as the sulfation reaction between sulfur dioxide (SO{sub 2}) and limestone in an uncalcined state. This reaction, based on oxyfuel combustion technology, was studied by thermogravimetric analysis. Surface morphologies of the limestone particles after sulfation were examined by a scanning electron microscope. Results show that there are more pores or gaps in the product layer formed by direct sulfation of limestone than by indirect sulfation, which can be attributed to the generation of carbon dioxide (CO{sub 2}) at a reaction interface. Compared with indirect sulfation, direct sulfation of limestone can yield much higher conversion and has a much higher reaction rate. For direct sulfation, the greater porosity in the product layer greatly reduces the solid-state ion diffusion distance, resulting in a higher reaction rate and higher conversion.

01 COAL, LIGNITE, AND PEAT↗

Comparison of the morphology of alkali–silica gel formed in limestones in concrete affected by the so-called alkali–carbonate reaction (ACR) and alkali–silica reaction (ASR)

The morphology of alkali–silica gel formed in dolomitic limestone affected by the so-called alkali–carbonate reaction (ACR) is compared to that formed in a siliceous limestone affected by alkali–silica reaction (ASR). The particle of dolomitic limestone was extracted from the experimental sidewalk in Kingston, Ontario, Canada that was badly cracked due to ACR. The siliceous limestone particle was extracted from a core taken from a highway structure in Quebec, affected by ASR. Both cores exhibited marked reaction rims around limestone particles. The aggregate particles were polished and given a light gold coating in preparation for examination in a scanning electron microscope. The gel in the ACR aggregate formed stringers between the calcite crystals in the matrix of the rock, whereas gel in ASR concrete formed a thick layer on top of the calcite crystals, that are of the same size as in the ACR aggregate.

36 MATERIALS SCIENCE↗

Limestone reaction in calcium aluminate cement–calcium sulfate systems

This paper reports a study of ternary blends composed of calcium aluminate cement, calcium sulfate hemihydrate and limestone. Compressive strength tests and hydration kinetics were studied as a function of limestone and calcium sulfate content. The phase evolution and the total porosity were followed and compared to thermodynamic simulation to understand the reactions involved and the effect of limestone on these binders. The reaction of limestone leads to the formation of hemicarboaluminate and monocarboaluminate. Increasing the ratio between sulfate and aluminate decreases the extent of limestone reaction.

36 MATERIALS SCIENCE↗

Toxicity of acid mine pit lake water remediated with limestone and phosphorus

Pit lakes are increasingly common worldwide and have potential to provide many benefits. However, lake water toxicity may require remediation before beneficial end uses can be realised. Three treatments to remediate AMD (pH similar to 4.8) pit lake water containing elevated concentrations of Al and Zn from Collie, Western Australia were tested in mesocosms. Treatments were: (a) limestone neutralisation (L), (b) phosphorus amendment (P), and c) combined limestone neutralisation and phosphorus amendment (L+P). Laboratory bioassays with Ceriodaphnia cf. dubia, Chlorella protothecoides and Tetrahymena thermophila assessed remediation. Limestone neutralisation increased pH and reduced heavy metal concentrations by 98% (Al) to 14% (Mg), removing toxicity to the three test species within 2 months. Phosphorus amendment removed toxicity after 6 months of treatment. However, phosphorus amendment to prior limestone neutralisation failed to reduce toxicity more than limestone neutralisation alone. Low concentrations of both phosphorus and nitrogen appear to limit phytoplankton population growth in all treatments.

01 COAL, LIGNITE, AND PEAT↗

Water quality changes in acid mine drainage streams in Gangneung, Korea, 10 years after treatment with limestone

To determine the long-term effectiveness of the limestone treatment for acid mine drainage (AMD) in Gangneung, Korea, we investigated the elemental distribution in streams impacted by AMD and compared the results of previous studies before and approximately 10 years after the addition of limestone. Addition of limestone in 1999 leads to a pH increase in 2008, and with the exception of Ca, the elemental concentrations (e.g., Fe, Mn, Mg, Sr, Ni, Zn, S) in the streams decreased. The pH was 2.5–3 before the addition of limestone and remained stable at around 4.5–5 from 2008 to 2011, suggesting the reactivity of the added limestone was diminished and that an alternative approach is needed to increase the pH up to circumneutral range and maintain effective long-term treatment. To identify the processes causing the decrease in the elemental concentrations, we also examined the spatial (approximately 7 km) distribution over three different types of streams affected by the AMD. Lastly, the elemental distribution was mainly controlled by physicochemical processes including redox reactions, dilution on mixing, and co-precipitation/adsorption with Fe (hydr)oxides.

58 GEOSCIENCES↗

Improvement of Alstom's Limestone-Based Chemical Looping Combustion Process for Higher Purity Flue Gas Production

Alstom Power Inc., a wholly owned subsidiary of the General Electric Company (GE), is developing Limestone-based Chemical Looping (LCL™) Processes, utilizing limestone derived calcium sulfate as an oxygen carrier to transport oxygen from air to the fuel. The LCL™ process is a breakthrough technology with the potential to capture CO 2 and SO 2 from new and existing coal-fired power plants at reduced costs while maintaining high plant power generation efficiency. Chemical looping is a next generation advancement to oxy-combustion which would not require the significant investment in a cryogenic distillation type oxygen production plant. Instead of the energy-consuming oxygen plant, chemical looping uses a benign material to directly remove oxygen from the air and bring that oxygen into contact with the fuel. This "game changing" technology is the lowest cost-of-electricity technical approach that GE Power has identified to date for coal power with carbon capture. The technology has significantly lower capital costs compared to a conventional steam power plant with first generation carbon capture technologies. This new power plant concept is based on a hybrid combustion-gasification process utilizing high temperature chemical and thermal looping technology. In the air reactor, a solid oxygen carrier picks up oxygen from air through an oxidation reaction and leaves nitrogen behind. The hot oxygen-carrying solid carrier is then transported to a fuel reactor, where it releases oxygen. The released oxygen then converts the coal in the fuel reactor into combustion gases. The solid carrier is recycled back to the air reactor for regeneration completing the “chemical loop.” The regeneration step produces heat from which steam is produced for power generation while the process results in a concentrated carbon dioxide stream in which the carbon is captured for use or sequestration (CCUS). Limestone as a precursor for the oxygen carrier is abundant, benign, low cost, and is used in CFB and PC boilers for sulfur control. Challenges associated with this carrier include a complex reaction mechanism with possible side reactions leading to the release of SO 2 . The present project (DOE/NETL Cooperative Agreement No. DE-FE0025073) report focuses on coal-fired Limestone Chemical Looping Combustion (LCL-C™) processes that can produce a higher purity flue gas stream and achieve an improved overall performance that will meet the stated DOE goal of generating power from coal while achieving greater than 90% CO2 removal at less than 35% increase in the Levelized Cost of Electricity (LCOE). It builds on the concurrent and synergistic limestone-based chemical looping combustion (LCL-C™) and gasification (LCL-G™) projects with the Department of Energy, that were executed in parallel with the present project. In this report, the LCL-C™ experimental testing from the electrically-heated, once-through, 100 kW Pilot-Scale Test Facility (PSTF) is analysed and reviewed. The PSTF Oxidizer is a 50-foot tall, 100-mm diameter transport reactor, while the PSTF Reducer reactor is based upon a bubbling-bed design. The experimental data from designated test periods (denoted “Weeks”) are reviewed and discussed. The application of high sulfur release in the Reducer (with proper sulfur management) exceeded the LCL-CTM performance targets. Furthermore, the ilmenite blend came within 1 percentage point of meeting all of the performance targets.

01 COAL, LIGNITE, AND PEAT↗