Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LEAD 184”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

Post-Test Inspection of NASA's Evolutionary Xenon Thruster Long-Duration Test Hardware: Discharge and Neutralizer Cathodes

The NEXT Long-Duration Test is part of a comprehensive thruster service life assessment intended to demonstrate overall throughput capability, validate service life models, quantify wear rates as a function of time and operating condition, and identify any unknown life-limiting mechanisms. The test was voluntarily terminated in February 2014 after demonstrating 51,184 hours of high-voltage operation, 918 kg of propellant throughput, and 35.5 MN-s of total impulse. The post-test inspection of the thruster hardware began shortly afterwards with a combination of non-destructive and destructive analysis techniques, and is presently nearing completion. This paper presents relevant results of the post-test inspection for both discharge and neutralizer cathodes. Discharge keeper erosion was found to be significantly reduced from what was observed in the NEXT 2 kh wear test and NSTAR Extended Life Test, providing adequate protection of vital cathode components throughout the test with ample lifetime remaining. The area of the discharge cathode orifice plate that was exposed by the keeper orifice exhibited net erosion, leading to cathode plate material building up in the cathode-keeper gap and causing a thermally-induced electrical short observed during the test. Significant erosion of the neutralizer cathode orifice was also found and is believed to be the root cause of an observed loss in flow margin. Deposition within the neutralizer keeper orifice as well as on the downstream surface was thicker than expected, potentially resulting in a facility-induced impact on the measured flow margin from plume mode. Neutralizer keeper wall erosion on the beam side was found to be significantly lower compared to the NEXT 2 kh wear test, likely due to the reduction in beam extraction diameter of the ion optics that resulted in decreased ion impingement. Results from the post-test inspection have led to some minor thruster design improvements.

Electric Propulsion↗

Post-test Inspection of NASA’s Evolutionary Xenon Thruster Long-Duration Test Hardware: Discharge and Neutralizer Cathodes

The NEXT Long-Duration Test is part of a comprehensive thruster service life assessment intended to demonstrate overall throughput capability, validate service life models, quantify wear rates as a function of time and operating condition, and identify any unknown life-limiting mechanisms. The test was voluntarily terminated in February 2014 after demonstrating 51,184 h of high-voltage operation, 918 kg of propellant throughput, and 35.5 MN-s of total impulse. The post-test inspection of the thruster hardware began shortly afterwards with a combination of non-destructive and destructive analysis techniques, and is presently nearing completion. This paper presents relevant results of the post-test inspection for both discharge and neutralizer cathodes. Discharge keeper erosion was found to be significantly reduced from what was observed in the NEXT 2 kh wear test and NSTAR Extended Life Test, providing adequate protection of vital cathode components throughout the test with ample lifetime remaining. The area of the discharge cathode orifice plate that was exposed by the keeper orifice exhibited net erosion, leading to cathode plate material building up in the cathode-keeper gap and causing a thermally-induced electrical short observed during the test. Significant erosion of the neutralizer cathode orifice was also found and is believed to be the root cause of an observed loss in flow margin. Deposition within the neutralizer keeper orifice as well as on the downstream surface was thicker than expected, potentially resulting in a facility-induced impact on the measured flow margin from plume mode. Neutralizer keeper wall erosion on the beam side was found to be significantly lower compared to the NEXT 2 kh wear test, likely due to the reduction in beam extraction diameter of the ion optics that resulted in decreased ion impingement. Results from the post-test inspection have led to some minor thruster design improvements.

Ion engine↗

Combining Modis and Quikscat Data to Delineate Surface and Near-Surface Melt on the Greenland Ice Sheet

Over the last two decades, increasing melt has been measured on the Greenland Ice Sheet, along with mass loss as determined from satellite data, Monitoring the state of the Greenland Ice Sheet becomes critical especially because it is actively losing mass, and the ice sheet has a sea-level rise potential of 7 in. However measurement of the extent of surface melt varies depending on the sensor used, whether it is passive or active microwave or visible or thermal infrared. We have used remote-sensing data products to study surface and near-surface melt characteristics of the Greenland Ice Sheet. We present a blended MODIS-QS melt daily product for 2007 [1]. The products, including Moderate Resolution Imaging Spectroradiometer (MODIS) daily land-surface temperature (LST) and a special daily melt product derived from the QuikSCAT (QS) scatterometer [2,3] show consistency in delineating the melt boundaries on a daily basis in the 2007 melt season [I], though some differences are identified. An assessment of maximum melt area for the 2007 melt shows that the QSCAT product detects a greater amount of melt (862,769 square kilometers) than is detected by the MODIS LST product (766,184 square kilometers). The discrepancy is largely because the QS product can detect both surface and near-surface melt and the QS product captures melt if it occurred anytime during the day while the MODIS product is obtained from a point in time on a given day. However on a daily bases, other factors influence the measurement of melt extent. In this work we employ the digital-elevation model of Bamber et al. [4] along with the National Centers for Environmental Prediction (NCEP) data to study some areas and time periods in detail during the 2007 melt season. We focus on times in which the QS and MODIS LST products do not agree exactly. We use NCEP and elevation data to analyze the atmospheric factors forcing the melt process, to gain an improved understanding of the conditions that lead to melt and melt persistence, and our ability to capture surface melt accurately using MODIS and QS data.

Hall, Dorothy K.↗