Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Kovar”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Elevated temperature creep properties of the 54Fe-29Ni-17Co "Kovar" alloy.

The outline of this presentation is: (1) Applications of Kovar Alloy in metal/ceramic brazing; (2) Diffusion bonding of precision-photoetched Kovar parts; (3) Sample composition and annealing conditions; (4) Intermediate temperature creep properties (350-650 C); (5) Power law creep correlations--with and without modulus correction; (6) Compressive stress-strain properties (23-900 C); (7) Effect of creep deformation on grain growth; and (8) Application of the power law creep correlation to the diffusion bonding application. The summary and conclusions are: Elevated temperature creep properties of Kovar from 750-900 C obey a power law creep equation with a stress exponent equal to 4.9, modulus compensated activation energy of 47.96 kcal/mole. Grain growth in Kovar creep samples tested at 750 and 800 C is quite sluggish. Significant grain growth occurs at 850 C and above, this is consistent with isothermal grain growth studies performed on Kovar alloy wires. Finite element analysis of the diffusion bonding of Kovar predict that stresses of 30 MPa and higher are needed for good bonding at 850 C, we believe that 'sintering' effects must be accounted for to allow FEA to be predictive of actual processing conditions. Additional creep tests are planned at 250-650 C.

36 MATERIALS SCIENCE↗

Laser Welding Characterization of Kovar and Stainless Steel Alloys as Suitable Materials for Components of Photonic Devices Packaging

The weldability of Kovar and stainless steel alloys by Nd:YAG laser beam is studied through changing of some laser beam parameters. It has been found that there is a suitable interaction of the pulsed laser beam of low power laser pulse with both the two alloys. The change of thermophysical properties with absorbed energy from the laser pulse is discussed in this paper which reports the suitability of both Kovar and stainless steel 304 as the base materials for photonic devices packaging. We used laser weld system (LW4000S from Newport) which employs Nd:YAG laser system with two simultaneous beams output for packaging 980 nm high power laser module. Results of changing both laser spot weld width and penetration depth with changing both the pulse peak power density, pulse energy and pulse duration show that there are good linear relationships between laser pulse energy or peak power density and pulse duration with laser spot weld dimensions( both laser spot weld width and penetration depth). Therefore we concluded that there should be an optimization for both the pulse peak power and pulse duration to give a suitable aspect ratio (laser spot width to penetration depth) for achieving the desired welds with suitable penetration depth and small spot width. This is to reduce the heat affected zone (HAZ) which affects the sensitive optical components. An optimum value of the power density in the order of 10{sup 5} w/cm{sup 2} found to be suitable to induce melting in the welded joints without vaporization. The desired ratio can also be optimized by changing the focus position on the target material as illustrated from our measurements. A theoretical model is developed to simulate the temperature distribution during the laser pulse heating and predict the penetration depth inside the material. Samples have been investigated using SEM with EDS. The metallographic measurements on the weld spot show a suitable weld yield with reasonable weld width to depth ratio.

36 MATERIALS SCIENCE↗

A strong and ductile Super Kovar alloy via fully coherent nanoprecipitates

Emerging high-precision technologies demand materials with exceptional dimensional stability and mechanical robustness, as even microscopic thermomechanical deformation can cause functional failure. However, a fundamental trilemma exists: High strength, ductility, and low thermal expansion are mutually exclusive, as strengthening-induced lattice distortions compromise the spin-lattice coupling, which is essential for low thermal expansion. Here, we overcome this trilemma by designing “Super Kovar,” an Fe-Ni-Co-Al-Ta alloy, featuring fully coherent nanoprecipitates. It unifies a 1.0-gigapascal ultimate tensile strength and ∼39% elongation with a Kovar-grade thermal expansion of 3.81 × 10−6 K−1 (100 to 410 K). The key is a dense dispersion of L12 nanoprecipitates that form an almost strain-free coherent interface with the ferromagnetic matrix. Beyond providing precipitation strengthening, these coherent interfaces suppress intrinsic phonons of nanoprecipitates via elastic coupling while avoiding magnetic domain pinning to preserve the Invar effect of the matrix. This reduces the thermal expansion of the precipitates by 56% and achieves a fourfold enhancement in the strength-ductility product, establishing a paradigm for dimensionally stable, ultrastrong alloys.

Yu, Chengyi [University of Science and Technology ↗

Effect of Annealing on the Microstructure and Properties of Electron Beam Welded 4J34 Kovar Alloy

Electron beam welding of 4J34 Kovar alloy was conducted, and the microstructure and mechanical properties of the joints in as-welded and postweld annealing treatment (PWAT) states were investigated. The martensitic transformation occurred and led to the generation of α lath martensite due to the rapid cooling in the as-welded condition. After annealing treatment, part of the α martensite transformed to γ austenite and subsequently developed the bulk γ phase and α/γ lamellar microstructures in the fusion zone (FZ) of the postwelded joint. Grains in the heat-affected zone (HAZ) clearly developed and penetrated into the FZ, causing the disappearance of the fusion line between the FZ and the HAZ. All the joints in both the as-welded and PWAT conditions exhibited ductile fracture. The maximum tensile strength of 505 MPa was obtained in the as-welded joint with the welding speed of 150 mm/min. The linear expansion coefficients of the joint and base metal decreased with the increase in temperature. However, the decreasing rate of PWAT joints was lower than that of the as-welded joints.

36 MATERIALS SCIENCE↗

Parallel-gap welding for joints between copper conductors and Kovar

Welding technique produces more reliable joints than soldering. Investigation used different sizes of copper conductors and component lead ribbons, corrosion protection platings, and melting points of metals being joined. Optimum combination is gold-plated component lead ribbons and solder-plated copper conductors.

Mc Daniel, G. E.↗

Borosilicate glass-to-Kovar tube bonding

Two-micron-diameter inlet leak, useful in mass spectrometry applications, minimizes gas sample distortion that occurs between sample and leak, is easily joined to spectrometer inlet system, and withstands unusual gas pressures and temperatures.

Harris, R. F.↗

Arcing in space structures in low Earth orbit

This report describes results of an experimental and theoretical program to investigate arcing of structures containing dielectric and conducting materials when they are biased negatively with respect to a plasma. An argon ion source generated Ar(+) ions of directed energy 20 to 40 eV and density approximately 10(exp 7) cm(exp -3) that impinged upon samples containing a dielectric material on top of a negatively biased Kovar plate. Arcing events were studied for bias voltages between -300 and -1000V with respect to the ion beam. The samples were Dow Corning 93-500 adhesive on Kovar, fused silica cover slips bonded on Kovar, and silicon solar cells mounted on Kovar. Measurements of discharge current, Kovar plate voltage, and radiation from the arc versus time were carried out. Microsecond duration exposure images and optical spectra in the 0.24 to 0.40 micron band were also acquired during arcing events. Arcing events were found to be associated with exposed adhesive and means were found to eliminate arcing altogether. The charging of a silica cover plate and the fields around the plate were calculated using a particle-in-cell code. Models were developed to explain the ignition of the arc and the physical processes occurring during the discharge.

Upschulte, B. L.↗

Mechanical design of ceramic beam tube braze joints for NOvA kicker magnets

The NO?A Experiment will construct a detector optimized for electron neutrino detection in the existing NuMI neutrino beam. The NuMI beam line is capable of operating at 400 kW of primary beam power and the upgrade will allow up to 700 kW. Ceramic beam tubes are utilized in numerous kicker magnets in different accelerator rings at Fermi National Accelerator Laboratory. Kovar flanges are brazed onto each beam tube end, since kovar and high alumina ceramic have similar expansion curves. The tube, kovar flange, end piece, and braze foil alloy brazing material are stacked in the furnace and then brazed. The most challenging aspect of fabricating kicker magnets in recent years have been making hermetic vacuum seals on the braze joints between the ceramic and flange. Numerous process variables can influence the robustness of conventional metal/ceramic brazing processes. The ceramic-filler metal interface is normally the weak layer when failure does not occur within the ceramic. Differences between active brazing filler metal and the moly-manganese process will be discussed along with the applicable results of these techniques used for Fermilab production kicker tubes.

43 PARTICLE ACCELERATORS↗

A data-driven multiscale model for reactive wetting simulations

Here, we describe a data-driven, multiscale technique to model reactive wetting of a silver–aluminum alloy on a Kovar™ (Fe-Ni-Co alloy) surface. We employ molecular dynamics simulations to elucidate the dependence of surface tension and wetting angle on the drop’s composition and temperature. A design of computational experiments is used to efficiently generate training data of surface tension and wetting angle from a limited number of molecular dynamics simulations. The simulation results are used to parameterize models of the material’s wetting properties and compute the uncertainty in the models due to limited data. The data-driven models are incorporated into an engineering-scale (continuum) model of a silver–aluminum sessile drop on a Kovar™ substrate. Model predictions of the wetting angle are compared with experiments of pure silver spreading on Kovar™ to quantify the model-form errors introduced by the limited training data versus the simplifications inherent in the molecular dynamics simulations. The paper presents innovations in the determination of “convergence” of noisy MD simulations before they are used to extract the wetting angle and surface tension, and the construction of their models which approximate physio-chemical processes that are left unresolved by the engineering-scale model. Together, these constitute a multiscale approach that integrates molecular-scale information into continuum scale models.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗